Ubuntu-fr

Alexandra

[RESOLU]I_O_support

Bonsoir mes amis,

j'ai des sérieux soucis, je pense même retourner sous windows ( nan je rigole... ), voilà mon soucis :

Mon pc refuse de garder le I_O_support à 32 bits, ce qui fait que je ne peux pas graver de cd ou dvd, le matos plante direct.......je vous copie ci dessous mon hdparm :

## This is the default configuration for hdparm for Debian.  It is a 
## rather simple script, so please follow the following guidelines :)
## Any line that begins with a comment is ignored - add as many as you 
## like.  Note that an in-line comment is not supported.  If a line 
## consists of whitespace only (tabs, spaces, carriage return), it will be
## ignored, so you can space control fields as you like.  ANYTHING ELSE
## IS PARSED!!  This means that lines with stray characters or lines that 
## use non # comment characters will be interpreted by the initscript.  
## This has probably minor, but potentially serious, side effects for your 
## hard drives, so please follow the guidelines.  Patches to improve 
## flexibilty welcome.  Please read /usr/share/doc/hdparm/README.Debian for 
## notes about known issues, especially if you have an MD array.
##
## Note that if the init script causes boot problems, you can pass 'nohdparm' 
## on the kernel command line, and the script will not be run.
##
## Uncommenting the options below will cause them to be added to the DEFAULT
## string which is prepended to options listed in the blocks below.
##
## If an option is listed twice, the second instance replaces the first.
##
## /sbin/hdparm is not run unless a block of the form:
##      DEV {
##         option
##         option
##         ...
##      }
## exists.  This blocks will cause /sbin/hdparm OPTIONS DEV to be run.
## Where OPTIONS is the concatenation of all options previously defined
## outside of a block and all options defined with in the block.

# -q be quiet
quiet 
# -a sector count for filesystem read-ahead
#read_ahead_sect = 12
# -A disable/enable the IDE drive's read-lookahead feature
#lookahead = on
# -b bus state
#bus = on
# -B apm setting
#apm = 255
# -c enable (E)IDE 32-bit I/O support - can be any of 0,1,3
#io32_support = 1
# -d disable/enable the "using_dma" flag for this drive
#dma = off
# -D enable/disable the on-drive defect management
#defect_mana = off
# -E cdrom speed
#cd_speed = 16
# -k disable/enable the "keep_settings_over_reset" flag for this drive
#keep_settings_over_reset = off
# -K disable/enable the drive's "keep_features_over_reset" flag
#keep_features_over_reset = on
# -m sector count for multiple sector I/O
#mult_sect_io = 32
# -P maximum sector count for the drive's internal prefetch mechanism
#prefetch_sect = 12
# -r read-only flag for device
#read_only = off
# -S standby (spindown) timeout for the drive
#spindown_time = 24
# -u interrupt-unmask flag for the drive
#interrupt_unmask = on
# -W Disable/enable the IDE drive's write-caching feature
#write_cache = off
# -X IDE transfer mode for newer (E)IDE/ATA2 drives
#transfer_mode = 34
# -y force to immediately enter the standby mode
#standby
# -Y force to immediately enter the sleep mode
#sleep
# -Z Disable the power-saving function of certain Seagate drives
#disable_seagate
# -M Set the acoustic management properties of a drive
#acoustic_management
# -p Set the chipset PIO mode
# chipset_pio_mode
# --security-freeze Freeze the drive's security status
# security_freeze
# --security-unlock Unlock the drive's security
# security_unlock = PWD
# --security-set-pass Set security password
# security_pass = password
# --security-disable Disable drive locking
# security_disable
# --user-master Select password to use
# user-master = u
# --security-mode Set the security mode
# security_mode = h

# Root file systems.  Please see README.Debian for details
# ROOTFS = /dev/hda

## New note - you can use straight hdparm commands in this config file 
## as well - the set up is ugly, but it keeps backwards compatibility
## Additionally, it should be noted that any blocks that begin with 
## the keyword 'command_line' are not run until after the root filesystem
## is mounted.  This is done to avoid running blocks twice.  If you need 
## to run hdparm to set parameters for your root disk, please use the 
## standard format.

#Samples follow:
#First three are good for devfs systems, fourth one for systems that do 
#not use devfs.  The fifth example uses straight hdparm command line
#syntax.  Any of the blocks that use command line syntax must begin with
#the keyword 'command_line', and no attempt is made to validate syntax.  
#It is provided for those more comfortable with hdparm syntax. 

#/dev/discs/disc0/disc {
#	mult_sect_io = 32
#	write_cache = on
#	spindown_time = 240
#	io32_support = 1
#}

#/dev/discs/disc1/disc {
#	mult_sect_io = 32
#	spindown_time = 36
#	write_cache = on
#	io32_support = 1
#}

#/dev/cdroms/cdrom0 {
#	dma = on		   
#	interrupt_unmask = on
#	io32_support = 1
#	cd_speed = 48
#}

#/dev/hda {
#	quiet
#	mult_sect_io = 32
#	write_cache = off
#	dma = on
#	io32_support = 1
#}

#command_line {
#       hdparm -q -m16 -q -W0 -q -d1 /dev/hda
#}

pourriez-vous m'aider, j'ai essayé plein de solutions sans résultats.

quand je fait un : sudo hdparm /dev/hda ca me donne ceci :

/dev/hda:
 multcount    =  0 (off)
 IO_support   =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 16383/255/63, sectors = 160086528, start = 0

I_O_support est à 16 bits !!!

Dernière modification par Alexandra (Le 18/04/2007, à 18:41)

---

Miss Geek is on www.ubuntu.cz
7.04 : Nová verze populárního opera?ního systému nabízí ?erstvý vzhled !!!

Alexandra

Re : [RESOLU]I_O_support

Je viens tout juste de trouver la solution, voici mon hdparm :

/dev/hda {
	quiet
	mult_sect_io = 32
	write_cache = off
	dma = on
	io32_support = 1
}

/dev/hdc {
	interrupt_unmask = on
  	quiet
  	dma = on
  	io32_support = 1
}

/dev/hdd {
	interrupt_unmask = on
  	quiet
  	dma = on
  	io32_support = 1
}

#command_line {
#       hdparm -q -m16 -q -W0 -q -d1 /dev/hda
#}

et voilà ce que ca donne :

/dev/hdd:
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)

---

Miss Geek is on www.ubuntu.cz
7.04 : Nová verze populárního opera?ního systému nabízí ?erstvý vzhled !!!