#1 Le 29/04/2007, à 14:50
- Aureschnoe
[ABANDON]Mon disque dur scsi ne fonctionne pas....
Bonjour,
Le possède un disque dur SCSI de 8GB qui fonctionne avec une carte SCSI TECKRAM dc315U. Mon problême est le suivant : le disque dur tourne bien, mais IMPOSSIBLE de le voir sous linux (je suis sous Ubuntu Feisty Fawn). Et le problême est le même avec les autres distributions de Ubuntu (et de linux d'ailleur). Je ne parviens pas a voir d'où vient le problême.
Voila !
Dernière modification par Aureschnoe (Le 17/05/2007, à 17:33)
Cordialement,
Aureschnoe.
Hors ligne
#2 Le 30/04/2007, à 12:05
- Desintegr
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Que donne : lsmod et dmesg ?
Hoc Volo, Sic Jubeo !
Mon wiki : http://desintegr.free.fr
Hors ligne
#3 Le 30/04/2007, à 19:03
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Voila ce que donne lsmode :
Module Size Used by
binfmt_misc 12680 1
rfcomm 40856 0
l2cap 25728 5 rfcomm
bluetooth 55908 4 rfcomm,l2cap
apm 22752 1
r128 40832 2
drm 81044 3 r128
ppdev 10116 0
cpufreq_powersave 2688 0
cpufreq_stats 7360 0
cpufreq_userspace 5408 0
cpufreq_ondemand 9228 0
cpufreq_conservative 8200 0
freq_table 5792 2 cpufreq_stats,cpufreq_ondemand
ipv6 268704 8
lp 12452 0
fuse 46612 0
snd_ens1370 21664 1
snd_pcm_oss 44544 0
snd_mixer_oss 17408 1 snd_pcm_oss
snd_pcm 79876 2 snd_ens1370,snd_pcm_oss
snd_ak4531_codec 9856 1 snd_ens1370
snd_seq_dummy 4740 0
snd_seq_oss 32896 0
sg 36252 0
sd_mod 23428 0
analog 12832 0
ns558 5760 0
gameport 16520 4 snd_ens1370,analog,ns558
snd_seq_midi 9600 0
snd_rawmidi 25472 2 snd_ens1370,snd_seq_midi
snd_seq_midi_event 8448 2 snd_seq_oss,snd_seq_midi
snd_seq 52592 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 23684 2 snd_pcm,snd_seq
snd_seq_device 9100 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
parport_pc 36388 1
parport 36936 3 ppdev,lp,parport_pc
snd 54020 12 snd_ens1370,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_ak4531_codec,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcspkr 4224 0
soundcore 8672 1 snd
snd_page_alloc 10888 2 snd_ens1370,snd_pcm
intel_agp 25116 1
agpgart 35400 2 drm,intel_agp
i2c_piix4 9740 0
i2c_core 22784 1 i2c_piix4
shpchp 34324 0
pci_hotplug 32576 1 shpchp
af_packet 23816 2
tsdev 8768 0
evdev 11008 1
reiserfs 247680 1
usbhid 26592 0
hid 27392 1 usbhid
ide_cd 32672 0
cdrom 37664 1 ide_cd
ide_disk 17024 3
floppy 59524 0
dc395x 35980 0
3c59x 46632 0
mii 6528 1 3c59x
uhci_hcd 25360 0
usbcore 134280 3 usbhid,uhci_hcd
piix 10756 0 [permanent]
generic 5124 0 [permanent]
ata_generic 9092 0
libata 125720 1 ata_generic
scsi_mod 142348 4 sg,sd_mod,dc395x,libata
fbcon 42656 0
tileblit 3584 1 fbcon
font 9216 1 fbcon
bitblit 6912 1 fbcon
softcursor 3200 1 bitblit
vesafb 9220 0
capability 5896 0
commoncap 8192 1 capabilityet voici ce que donne dmesg :
[ 0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 00000000000a0000 end: 00000000000a0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 0000000017f00000 end: 0000000018000000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000018000000 (usable)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 384MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 98304) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 98304
[ 0.000000] HighMem 98304 -> 98304
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 98304
[ 0.000000] On node 0 totalpages: 98304
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 736 pages used for memmap
[ 0.000000] Normal zone: 93472 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.0 present.
[ 0.000000] ACPI: Unable to locate RSDP
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 18000000:e7ff0000)
[ 0.000000] Detected 501.182 MHz processor.
[ 34.254323] Built 1 zonelists. Total pages: 97536
[ 34.254339] Kernel command line: root=UUID=636e84fb-2513-4bfb-8dfe-59a2a2329224 ro quiet splash locale=fr_FR apm=off acpi=force
[ 34.255240] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 34.255283] mapped APIC to ffffd000 (0130a000)
[ 34.255299] Enabling fast FPU save and restore... done.
[ 34.255349] Initializing CPU#0
[ 34.255507] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 34.257194] Console: colour VGA+ 80x25
[ 34.259148] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 34.262078] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 34.321487] Memory: 378436k/393216k available (1992k kernel code, 14164k reserved, 893k data, 328k init, 0k highmem)
[ 34.321532] virtual kernel memory layout:
[ 34.321537] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 34.321543] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 34.321549] vmalloc : 0xd8800000 - 0xff7fe000 ( 623 MB)
[ 34.321555] lowmem : 0xc0000000 - 0xd8000000 ( 384 MB)
[ 34.321561] .init : 0xc03d7000 - 0xc0429000 ( 328 kB)
[ 34.321567] .data : 0xc02f2264 - 0xc03d16d4 ( 893 kB)
[ 34.321572] .text : 0xc0100000 - 0xc02f2264 (1992 kB)
[ 34.321586] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 34.399494] Calibrating delay using timer specific routine.. 1003.36 BogoMIPS (lpj=2006723)
[ 34.399662] Security Framework v1.0.0 initialized
[ 34.399692] SELinux: Disabled at boot.
[ 34.399762] Mount-cache hash table entries: 512
[ 34.400309] CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 34.400356] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 34.400367] CPU: L2 cache: 128K
[ 34.400380] CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 34.400424] Compat vDSO mapped to ffffe000.
[ 34.400456] Remapping vsyscall page to ffffe000
[ 34.400493] Checking 'hlt' instruction... OK.
[ 34.415601] SMP alternatives: switching to UP code
[ 34.416224] Freeing SMP alternatives: 11k freed
[ 34.417011] Early unpacking initramfs... done
[ 35.778229] CPU0: Intel Celeron (Mendocino) stepping 05
[ 35.778256] SMP motherboard not detected.
[ 35.778266] Local APIC not detected. Using dummy APIC emulation.
[ 35.778458] Brought up 1 CPUs
[ 35.779540] Booting paravirtualized kernel on bare hardware
[ 35.779850] Time: 16:44:26 Date: 03/30/107
[ 35.779988] NET: Registered protocol family 16
[ 35.780463] EISA bus registered
[ 35.812856] PCI: PCI BIOS revision 2.10 entry at 0xfb390, last bus=1
[ 35.812867] PCI: Using configuration type 1
[ 35.812875] Setting up standard PCI resources
[ 35.816789] ACPI: Interpreter disabled.
[ 35.816811] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 35.816849] pnp: PnP ACPI: disabled
[ 35.816865] PnPBIOS: Scanning system for PnP BIOS support...
[ 35.817568] PnPBIOS: Found PnP BIOS installation structure at 0xc00fbf30
[ 35.817591] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf58, dseg 0xf0000
[ 35.823451] PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
[ 35.823720] PCI: Probing PCI hardware
[ 35.823739] PCI: Probing PCI hardware (bus 00)
[ 35.824340] * Found PM-Timer Bug on the chipset. Due to workarounds for a bug,
[ 35.824349] * this clock source is slow. Consider trying other clock sources
[ 35.824423] PCI quirk: region 4000-403f claimed by PIIX4 ACPI
[ 35.824436] PCI quirk: region 5000-500f claimed by PIIX4 SMB
[ 35.824988] Boot video device is 0000:01:00.0
[ 35.828317] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 35.915963] NET: Registered protocol family 8
[ 35.915974] NET: Registered protocol family 20
[ 35.916323] pnp: 00:0a: ioport range 0x208-0x20f has been reserved
[ 35.918039] PCI: Bridge: 0000:00:01.0
[ 35.918056] IO window: d000-dfff
[ 35.918071] MEM window: e8000000-e9ffffff
[ 35.918084] PREFETCH window: e4000000-e7ffffff
[ 35.918213] NET: Registered protocol family 2
[ 35.951648] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 35.952034] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 35.952776] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 35.953339] TCP: Hash tables configured (established 16384 bind 8192)
[ 35.953354] TCP reno registered
[ 35.963889] checking if image is initramfs... it is
[ 38.498845] Freeing initrd memory: 6998k freed
[ 38.500628] audit: initializing netlink socket (disabled)
[ 38.500679] audit(1177951469.392:1): initialized
[ 38.501272] VFS: Disk quotas dquot_6.5.1
[ 38.501354] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 38.501580] io scheduler noop registered
[ 38.501593] io scheduler anticipatory registered
[ 38.501603] io scheduler deadline registered
[ 38.501651] io scheduler cfq registered (default)
[ 38.501680] Limiting direct PCI/PCI transfers.
[ 38.502579] isapnp: Scanning for PnP cards...
[ 38.613961] pnp: SB audio device quirk - increasing port range
[ 38.614457] isapnp: Card 'Creative ViBRA16X PnP'
[ 38.614472] isapnp: 1 Plug & Play card detected total
[ 38.852616] Real Time Clock Driver v1.12ac
[ 38.852972] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 38.853327] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 38.854234] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 38.857849] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 38.859265] 00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 38.860684] mice: PS/2 mouse device common for all mice
[ 38.864063] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 38.864833] input: Macintosh mouse button emulation as /class/input/input0
[ 38.865032] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 38.865051] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 38.865859] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 38.865876] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 39.119407] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 39.120093] EISA: Probing bus 0 at eisa.0
[ 39.120161] Cannot allocate resource for EISA slot 4
[ 39.120171] Cannot allocate resource for EISA slot 5
[ 39.120199] EISA: Detected 0 cards.
[ 39.120523] TCP cubic registered
[ 39.120552] NET: Registered protocol family 1
[ 39.120638] Using IPI No-Shortcut mode
[ 39.120734] Magic number: 3:623:743
[ 39.122968] Time: tsc clocksource has been installed.
[ 39.123292] Freeing unused kernel memory: 328k freed
[ 39.143127] input: AT Translated Set 2 keyboard as /class/input/input1
[ 41.229318] Capability LSM initialized
[ 41.474788] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 44.107549] SCSI subsystem initialized
[ 44.149604] libata version 2.20 loaded.
[ 44.168568] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 44.168617] PIIX4: chipset revision 1
[ 44.168626] PIIX4: not 100% native mode: will probe irqs later
[ 44.168649] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 44.168688] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 44.168716] Probing IDE interface ide0...
[ 44.240997] usbcore: registered new interface driver usbfs
[ 44.241098] usbcore: registered new interface driver hub
[ 44.241230] usbcore: registered new device driver usb
[ 44.247887] USB Universal Host Controller Interface driver v3.0
[ 44.594488] hda: FUJITSU MPD3064AT, ATA DISK drive
[ 44.871806] Floppy drive(s): fd0 is 1.44M
[ 44.969049] FDC 0 is a post-1991 82077
[ 45.042436] hdb: TSSTcorpDVD-ROM SH-D162C, ATAPI CD/DVD-ROM drive
[ 45.098853] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 45.099116] Probing IDE interface ide1...
[ 45.834322] hdc: RICOH CD-R/RW MP7200A, ATAPI CD/DVD-ROM drive
[ 46.170718] ide1 at 0x170-0x177,0x376 on irq 15
[ 46.172149] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 46.173232] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 46.173307] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000e000
[ 46.176076] usb usb1: configuration #1 chosen from 1 choice
[ 46.177201] hub 1-0:1.0: USB hub found
[ 46.177274] hub 1-0:1.0: 2 ports detected
[ 46.208533] hda: max request size: 128KiB
[ 46.208555] hda: 12672450 sectors (6488 MB) w/512KiB Cache, CHS=13410/15/63, UDMA(33)
[ 46.208576] hda: cache flushes not supported
[ 46.208693] hda: hda1 hda2
[ 46.278701] PCI: setting IRQ 12 as level-triggered
[ 46.278718] PCI: Found IRQ 12 for device 0000:00:0a.0
[ 46.278777] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[ 46.278801] 0000:00:0a.0: 3Com PCI 3c905C Tornado at d8846000.
[ 46.300449] dc395x: Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040 v2.05, 2004/03/08
[ 46.300496] PCI: setting IRQ 5 as level-triggered
[ 46.300507] PCI: Found IRQ 5 for device 0000:00:0b.0
[ 46.543617] dc395x: Used settings: AdapterID=07, Speed=0(20.0MHz), dev_mode=0x57
[ 46.543633] dc395x: AdaptMode=0x0f, Tags=4(16), DelayReset=1s
[ 46.543647] dc395x: Connectors: int50 Termination: Auto Low High
[ 46.543823] dc395x: Performing initial SCSI bus reset
[ 46.544347] scsi0 : Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040 v2.05, 2004/03/08
[ 46.631898] hdb: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
[ 46.631931] Uniform CD-ROM driver Revision: 3.20
[ 46.723570] hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 46.750150] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 46.925598] usb 1-1: configuration #1 chosen from 1 choice
[ 47.004733] usbcore: registered new interface driver hiddev
[ 47.043090] input: Logitech Optical USB Mouse as /class/input/input2
[ 47.043801] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:07.2-1
[ 47.043863] usbcore: registered new interface driver usbhid
[ 47.043891] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 47.317375] Attempting manual resume
[ 47.317391] swsusp: Resume From Partition 3:2
[ 47.317399] PM: Checking swsusp image.
[ 47.318065] PM: Resume from disk failed.
[ 47.363570] ReiserFS: hda1: found reiserfs format "3.6" with standard journal
[ 47.363606] ReiserFS: hda1: using ordered data mode
[ 47.385518] ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 47.395102] ReiserFS: hda1: checking transaction log (hda1)
[ 47.474339] ReiserFS: hda1: Using r5 hash to sort names
[ 48.407263] dc395x: Target 00: Sync: 48ns Offset 15 (20.8 MB/s)
[ 48.408620] scsi 0:0:0:0: Direct-Access SEAGATE ST39236LW 0004 PQ: 0 ANSI: 3
[ 66.885142] eth0: setting half-duplex.
[ 68.386450] NET: Registered protocol family 17
[ 72.073514] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 72.126239] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 72.312758] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 73.334464] Linux agpgart interface v0.102 (c) Dave Jones
[ 73.946213] agpgart: Detected an Intel 440BX Chipset.
[ 73.952843] agpgart: AGP aperture is 64M @ 0xe0000000
[ 74.682766] input: PC Speaker as /class/input/input3
[ 75.565950] parport: PnPBIOS parport detected.
[ 75.566027] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 75.967613] pnp: Device 01:01.01 activated.
[ 75.984836] gameport: NS558 PnP Gameport is pnp01:01.01/gameport0, io 0x201, speed 685kHz
[ 76.150706] sda : READ CAPACITY failed.
[ 76.150714] sda : status=12, message=00, host=7, driver=00
[ 76.150727] sda : sense not available.
[ 76.152949] sda: test WP failed, assume Write Enabled
[ 76.153678] sda: asking for cache data failed
[ 76.153692] sda: assuming drive cache: write through
[ 76.154067] sd 0:0:0:0: Attached scsi disk sda
[ 76.436502] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 77.477182] PCI: setting IRQ 11 as level-triggered
[ 77.477199] PCI: Found IRQ 11 for device 0000:00:09.0
[ 78.235609] fuse init (API version 7.8)
[ 78.307343] lp0: using parport0 (interrupt-driven).
[ 78.456052] Adding 514072k swap on /dev/disk/by-uuid/ee2be880-500d-4a50-9d3b-e5548db16e77. Priority:-1 extents:1 across:514072k
[ 85.206823] NET: Registered protocol family 10
[ 85.207166] lo: Disabled Privacy Extensions
[ 94.563010] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 94.563463] acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
[ 94.564521] acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
[ 94.565167] acpi_cpufreq: Unknown symbol acpi_processor_register_performance
[ 96.192292] eth0: no IPv6 routers present
[ 108.282728] ppdev: user-space parallel port driver
[ 109.791850] [drm] Initialized drm 1.1.0 20060810
[ 109.980048] [drm] Initialized r128 2.5.0 20030725 on minor 0
[ 109.984476] agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
[ 109.985615] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 109.986610] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 112.806664] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 115.731831] Bluetooth: Core ver 2.11
[ 115.732028] NET: Registered protocol family 31
[ 115.732038] Bluetooth: HCI device and connection manager initialized
[ 115.732052] Bluetooth: HCI socket layer initialized
[ 116.000617] Bluetooth: L2CAP ver 2.8
[ 116.000635] Bluetooth: L2CAP socket layer initialized
[ 116.227650] Bluetooth: RFCOMM socket layer initialized
[ 116.227702] Bluetooth: RFCOMM TTY layer initialized
[ 116.227711] Bluetooth: RFCOMM ver 1.8
[ 120.585438] eth0: no IPv6 routers presentCordialement,
Aureschnoe.
Hors ligne
#4 Le 02/05/2007, à 14:05
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
up
Cordialement,
Aureschnoe.
Hors ligne
#5 Le 02/05/2007, à 14:17
- Desintegr
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
La carte est bien détectée, les modules sont bien chargés.
Le disque a l'air d'être également bien détecté. Il s'agit bien d'un Seagate ST39236LW ?
Que donne ls -l /dev/sd* et fdisk -l /dev/sda ?
Hoc Volo, Sic Jubeo !
Mon wiki : http://desintegr.free.fr
Hors ligne
#6 Le 02/05/2007, à 14:32
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Voila ce que donne ls -l /dev/sd* :
brw-rw---- 1 root disk 8, 0 2007-05-02 13:54 /dev/sdaEt voila ce que donne fdisk -l /dev/sda :
Ne peut ouvrir /dev/sdaPar contre sous root le fdisk -l /dev/sda ne donne rien (lorsque je fais entrée, aucun messages ne s'affiche) :
root@Aureschnoe:~# fdisk -l /dev/sda
root@Aureschnoe:~#Dernière modification par Aureschnoe (Le 02/05/2007, à 14:34)
Cordialement,
Aureschnoe.
Hors ligne
#7 Le 02/05/2007, à 14:34
- Desintegr
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Et avec sudo ça donne ?
Dernière modification par Desintegr (Le 02/05/2007, à 14:36)
Hoc Volo, Sic Jubeo !
Mon wiki : http://desintegr.free.fr
Hors ligne
#8 Le 02/05/2007, à 14:35
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Avec sudo sa ne donne rien
Cordialement,
Aureschnoe.
Hors ligne
#9 Le 02/05/2007, à 14:36
- Desintegr
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
J'ai vu dans ton dmesg un READ CAPACITY failed. C'est peut-être la raison pour laquelle ton disque dur ne fonctionne pas. Teste le sur un autre OS ou sur un autre ordinateur.
Tu es certain qu'il fonctionne correctement ?
Dernière modification par Desintegr (Le 02/05/2007, à 14:38)
Hoc Volo, Sic Jubeo !
Mon wiki : http://desintegr.free.fr
Hors ligne
#10 Le 02/05/2007, à 14:39
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Ba justement quand j'avais windows mon disque fonctionnai parfaitement, et quand il était sur l'ordi de ma soeur c'est pareil, il marchai bien. C'est pour ça que je ne comprend pas. Et en plus, en live cd avec ubuntu, mon disque est bien vu...
Cordialement,
Aureschnoe.
Hors ligne
#11 Le 03/05/2007, à 18:05
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
up
Cordialement,
Aureschnoe.
Hors ligne
#12 Le 03/05/2007, à 19:53
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
up encore, s'il vous plait, c'est assez urgent...
Cordialement,
Aureschnoe.
Hors ligne
#13 Le 06/05/2007, à 16:42
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
up up up please !!! Personne ne peux donc m'aider ?
Cordialement,
Aureschnoe.
Hors ligne
#14 Le 09/05/2007, à 17:42
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
up up up up HELP !!!!!
Cordialement,
Aureschnoe.
Hors ligne
#15 Le 17/05/2007, à 17:34
- Aureschnoe
Re : [ABANDON]Mon disque dur scsi ne fonctionne pas....
Bon, je vais acheter une nouvelle carte scsi vu que personne ne peu m'aider
Cordialement,
Aureschnoe.
Hors ligne