Ubuntu-fr

jackeson

Psensors et son installation pour la surveillance des Températures !

Bonjour ayant fais la manipulation pour installer
Psensors suivant la définition suivante :

sudo apt-get install lm-sensors
sudo sensors-detect
sensors
sudo apt-add-repository ppa:jfi/psensor-unstable
sudo apt-get update
sudo apt-get install psensor

trouver sur la page suivante
http://forum.ubuntu-fr.org/viewtopic.php?id=535381

J'obtiens la réponse en voulant installer

sudo sensors-detect
[sudo] password for jackeson: 
# sensors-detect revision 5984 (2011-07-10 21:22:53 +0200)
# System: PACKARD BELL BV 0000000000
# Board: PACKARD BELL BV GA-T671MG

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): YES
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 15h power sensors...                             No
Intel digital thermal sensor...                             No
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      Yes
Found `ITE IT8718F Super IO Sensors'                        Success!
    (address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): YES
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): YES
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): YES
Sorry, no supported PCI bus adapters found.
Module i2c-dev loaded successfully.

Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `it87':
  * ISA bus, address 0x290
    Chip `ITE IT8718F Super IO Sensors' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
it87
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)YES
Successful!

Monitoring programs won't work until the needed modules are
loaded. You may want to run 'service module-init-tools start'
to load them.

Unloading i2c-dev... OK
Unloading cpuid... OK

et comme résultat j'obtiens

jackeson@jackeson-0000000000:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +40.0°C  (crit = +75.0°C)

au lieu d'obtenir la réponse suivante

# sensors-detect revision 5861 (2010-09-21 17:21:05 +0200)
# System: Hewlett-Packard HP Pavilion dv8 Notebook PC (laptop)
# Board: Hewlett-Packard 7001

joe7@ubuntu:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:       +52.0°C                                    

coretemp-isa-0000
Adapter: ISA adapter
Core 0:      +52.0°C  (high = +84.0°C, crit = +100.0°C)  

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +50.0°C  (high = +84.0°C, crit = +100.0°C)  

coretemp-isa-0002
Adapter: ISA adapter
Core 2:      +51.0°C  (high = +84.0°C, crit = +100.0°C)  

Avce Psensor j'obtiens

Pouvez vous m'éclairer de vos connaissances afin de régler ce problème.
Merci à vous tous et bonne soirée.

Dernière modification par jackeson (Le 14/04/2013, à 19:43)

linuxienubuntiste

Re : Psensors et son installation pour la surveillance des Températures !

Monitoring programs won't work until the needed modules are
loaded. You may want to run 'service module-init-tools start'
to load them.

???

jackeson

Re : Psensors et son installation pour la surveillance des Températures !

rien n'y change c'est toujours pareil.