Contenu | Rechercher | Menus

Annonce

Si vous rencontrez des soucis à rester connecté sur le forum (ou si vous avez perdu votre mot de passe) déconnectez-vous et reconnectez-vous depuis cette page, en cochant la case "Me connecter automatiquement lors de mes prochaines visites". Attention, le forum rencontre actuellement quelques difficultés. En cas d'erreur 502, il ne faut pas re-valider l'envoi d'un message ou l'ouverture d'une discussion, au risque de créer un doublon.

La section divers se réorganise ! De nouvelles sous-sections à venir. (plus d'infos + donner son avis)

#1 Le 12/09/2013, à 13:45

miir83

Clef usb plus reconnue

Bonjour, cela concerne une mini clef usb EMTEC 4Go qui n'est plus accessible.
- elle s'éclaire et reste éclairée dans le port usb
- dans le poste de travail : Generic DEVICE STORAGE apparaît
- elle n'est pas reconnue dans GPARTED
- lsusb
Bus 001 Device 007: ID 05e3:0727 Genesys Logic, Inc. microSD Reader/Writer
Bus 005 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 005 Device 003: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
- dmesg
  0.138452] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.138457] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.138549] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.138679] system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved
[    0.138686] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.138782] system 00:0d: [mem 0xe0000000-0xefffffff] has been reserved
[    0.138789] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.139017] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.139023] system 00:0e: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.139027] system 00:0e: [mem 0x00100000-0x7fffffff] could not be reserved
[    0.139032] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.139252] pnp: PnP ACPI: found 15 devices
[    0.139255] ACPI: ACPI bus type pnp unregistered
[    0.139261] PnPBIOS: Disabled by ACPI PNP
[    0.177434] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.177441] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[    0.177458] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[    0.177462] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.177470] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff]
[    0.177476] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref]
[    0.177482] pci 0000:01:00.1: BAR 0: assigned [mem 0xcf000000-0xcf003fff]
[    0.177489] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.177494] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.177500] pci 0000:00:01.0:   bridge window [mem 0xce000000-0xcfefffff]
[    0.177505] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfefffff pref]
[    0.177512] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.177517] pci 0000:00:1c.0:   bridge window [io  0xd000-0xdfff]
[    0.177524] pci 0000:00:1c.0:   bridge window [mem 0x80000000-0x801fffff]
[    0.177530] pci 0000:00:1c.0:   bridge window [mem 0x80200000-0x803fffff 64bit pref]
[    0.177539] pci 0000:00:1e.0: PCI bridge to [bus 03]
[    0.177544] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.177551] pci 0000:00:1e.0:   bridge window [mem 0xcff00000-0xcfffffff]
[    0.177557] pci 0000:00:1e.0:   bridge window [mem 0xdff00000-0xdfffffff 64bit pref]
[    0.177593] pci 0000:00:1e.0: setting latency timer to 64
[    0.177600] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.177604] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[    0.177608] pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
[    0.177612] pci_bus 0000:01: resource 1 [mem 0xce000000-0xcfefffff]
[    0.177615] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfefffff pref]
[    0.177619] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    0.177622] pci_bus 0000:02: resource 1 [mem 0x80000000-0x801fffff]
[    0.177626] pci_bus 0000:02: resource 2 [mem 0x80200000-0x803fffff 64bit pref]
[    0.177630] pci_bus 0000:03: resource 0 [io  0xe000-0xefff]
[    0.177633] pci_bus 0000:03: resource 1 [mem 0xcff00000-0xcfffffff]
[    0.177637] pci_bus 0000:03: resource 2 [mem 0xdff00000-0xdfffffff 64bit pref]
[    0.177641] pci_bus 0000:03: resource 4 [io  0x0000-0xffff]
[    0.177644] pci_bus 0000:03: resource 5 [mem 0x00000000-0xfffffffff]
[    0.177691] NET: Registered protocol family 2
[    0.177889] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.177925] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.177960] TCP: Hash tables configured (established 8192 bind 8192)
[    0.177997] TCP: reno registered
[    0.178002] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.178011] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.178082] NET: Registered protocol family 1
[    0.178273] pci 0000:01:00.0: Boot video device
[    0.178302] PCI: CLS 16 bytes, default 64
[    0.178376] Trying to unpack rootfs image as initramfs...
[    0.598451] Freeing initrd memory: 15692k freed
[    0.608622] Initialise module verification
[    0.608679] audit: initializing netlink socket (disabled)
[    0.608698] type=2000 audit(1378989891.608:1): initialized
[    0.635645] bounce pool size: 64 pages
[    0.635664] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.638063] VFS: Disk quotas dquot_6.5.2
[    0.638135] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.639009] fuse init (API version 7.20)
[    0.639153] msgmni has been set to 1719
[    0.639890] Key type asymmetric registered
[    0.639897] Asymmetric key parser 'x509' registered
[    0.639960] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.640024] io scheduler noop registered
[    0.640031] io scheduler deadline registered (default)
[    0.640045] io scheduler cfq registered
[    0.640261] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.640376] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.640487] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.640513] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.640725] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.640733] ACPI: Power Button [PWRB]
[    0.640798] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.640804] ACPI: Power Button [PWRF]
[    0.645308] GHES: HEST is not enabled!
[    0.645384] isapnp: Scanning for PnP cards...
[    0.645468] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.648104] Linux agpgart interface v0.103
[    0.650965] brd: module loaded
[    0.652358] loop: module loaded
[    0.652578] ata_piix 0000:00:1f.1: version 2.13
[    0.652652] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.653103] scsi0 : ata_piix
[    0.654557] scsi1 : ata_piix
[    0.655520] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    0.655525] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    0.655552] ata_piix 0000:00:1f.2: MAP [
[    0.655556]  P0 P2 P1 P3 ]
[    0.655609] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.656062] scsi2 : ata_piix
[    0.656161] scsi3 : ata_piix
[    0.656230] ata3: SATA max UDMA/133 cmd 0xb400 ctl 0xb080 bmdma 0xa880 irq 19
[    0.656234] ata4: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa888 irq 19
[    0.656833] libphy: Fixed MDIO Bus: probed
[    0.656985] tun: Universal TUN/TAP device driver, 1.6
[    0.656989] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.657076] PPP generic driver version 2.4.2
[    0.657155] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.657159] ehci-pci: EHCI PCI platform driver
[    0.657207] ehci-pci 0000:00:1d.7: setting latency timer to 64
[    0.657214] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.657226] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.657246] ehci-pci 0000:00:1d.7: debug port 1
[    0.661149] ehci-pci 0000:00:1d.7: cache line size of 16 is not supported
[    0.661179] ehci-pci 0000:00:1d.7: irq 23, io mem 0xcdffbc00
[    0.661421] ata2: port disabled--ignoring
[    0.672027] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.672083] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.672089] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.672094] usb usb1: Product: EHCI Host Controller
[    0.672099] usb usb1: Manufacturer: Linux 3.8.0-30-generic ehci_hcd
[    0.672103] usb usb1: SerialNumber: 0000:00:1d.7
[    0.672294] hub 1-0:1.0: USB hub found
[    0.672303] hub 1-0:1.0: 8 ports detected
[    0.672579] ehci-platform: EHCI generic platform driver
[    0.672598] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.672633] uhci_hcd: USB Universal Host Controller Interface driver
[    0.672671] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.672678] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.672689] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.672719] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000b480
[    0.672773] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.672779] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.672783] usb usb2: Product: UHCI Host Controller
[    0.672788] usb usb2: Manufacturer: Linux 3.8.0-30-generic uhci_hcd
[    0.672792] usb usb2: SerialNumber: 0000:00:1d.0
[    0.672961] hub 2-0:1.0: USB hub found
[    0.672970] hub 2-0:1.0: 2 ports detected
[    0.673108] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.673114] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.673124] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.673154] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b800
[    0.673205] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.673210] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.673215] usb usb3: Product: UHCI Host Controller
[    0.673220] usb usb3: Manufacturer: Linux 3.8.0-30-generic uhci_hcd
[    0.673224] usb usb3: SerialNumber: 0000:00:1d.1
[    0.673390] hub 3-0:1.0: USB hub found
[    0.673399] hub 3-0:1.0: 2 ports detected
[    0.673539] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.673545] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.673555] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.673600] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b880
[    0.673650] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.673656] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.673661] usb usb4: Product: UHCI Host Controller
[    0.673665] usb usb4: Manufacturer: Linux 3.8.0-30-generic uhci_hcd
[    0.673670] usb usb4: SerialNumber: 0000:00:1d.2
[    0.673833] hub 4-0:1.0: USB hub found
[    0.673841] hub 4-0:1.0: 2 ports detected
[    0.673978] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.673985] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.673994] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.674037] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000bc00
[    0.674093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.674099] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.674103] usb usb5: Product: UHCI Host Controller
[    0.674108] usb usb5: Manufacturer: Linux 3.8.0-30-generic uhci_hcd
[    0.674113] usb usb5: SerialNumber: 0000:00:1d.3
[    0.674276] hub 5-0:1.0: USB hub found
[    0.674284] hub 5-0:1.0: 2 ports detected
[    0.674552] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.674556] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.675437] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.675603] mousedev: PS/2 mouse device common for all mice
[    0.675807] rtc_cmos 00:02: RTC can wake from S4
[    0.675969] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.676018] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[    0.676206] device-mapper: uevent: version 1.0.3
[    0.676321] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com
[    0.676355] EISA: Probing bus 0 at eisa.0
[    0.676394] EISA: Detected 0 cards.
[    0.676410] cpufreq-nforce2: No nForce2 chipset.
[    0.676415] cpuidle: using governor ladder
[    0.676419] cpuidle: using governor menu
[    0.676425] ledtrig-cpu: registered to indicate activity on CPUs
[    0.676428] EFI Variables Facility v0.08 2004-May-17
[    0.676754] ashmem: initialized
[    0.676968] TCP: cubic registered
[    0.677173] NET: Registered protocol family 10
[    0.677491] NET: Registered protocol family 17
[    0.677509] Key type dns_resolver registered
[    0.677764] Using IPI No-Shortcut mode
[    0.677904] Loading module verification certificates
[    0.684837] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: 6780d094f850d74b33615e841427c3cb80cda14b'
[    0.684864] registered taskstats version 1
[    0.689881] Key type trusted registered
[    0.696508] Key type encrypted registered
[    0.701521] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    0.701716] rtc_cmos 00:02: setting system clock to 2013-09-12 12:44:52 UTC (1378989892)
[    0.701813] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.701817] EDD information not available.
[    0.944145] ata3.00: ATA-6: ST3200822AS, 3.02, max UDMA/100
[    0.944153] ata3.00: 390721968 sectors, multi 16: LBA48
[    0.945137] ata3.01: ATA-7: Maxtor 6L160M0, BANC1G10, max UDMA/133
[    0.945143] ata3.01: 320173056 sectors, multi 16: LBA48 NCQ (not used)
[    0.960144] ata3.00: configured for UDMA/100
[    0.977105] ata3.01: configured for UDMA/133
[    0.998758] isapnp: No Plug & Play device found
[    1.016326] ata1.00: ATAPI: LITE-ON DVDRW SOHW-832S, VPDD, max UDMA/33
[    1.016344] ata1.01: ATAPI: LITE-ON DVDRW SHM-165P6S, MS0P, max UDMA/66
[    1.016350] ata1.01: limited to UDMA/33 due to 40-wire cable
[    1.032203] ata1.00: configured for UDMA/33
[    1.064203] ata1.01: configured for UDMA/33
[    1.066100] scsi 0:0:0:0: CD-ROM            LITE-ON  DVDRW SOHW-832S  VPDD PQ: 0 ANSI: 5
[    1.068340] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[    1.068345] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.068510] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.068683] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.069916] scsi 0:0:1:0: CD-ROM            LITE-ON  DVDRW SHM-165P6S MS0P PQ: 0 ANSI: 5
[    1.072305] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.072459] sr 0:0:1:0: Attached scsi CD-ROM sr1
[    1.072609] sr 0:0:1:0: Attached scsi generic sg1 type 5
[    1.072852] scsi 2:0:0:0: Direct-Access     ATA      ST3200822AS      3.02 PQ: 0 ANSI: 5
[    1.073027] sd 2:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
[    1.073133] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    1.073189] sd 2:0:0:0: [sda] Write Protect is off
[    1.073197] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.073252] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.073369] scsi 2:0:1:0: Direct-Access     ATA      Maxtor 6L160M0   BANC PQ: 0 ANSI: 5
[    1.073632] sd 2:0:1:0: Attached scsi generic sg3 type 0
[    1.073760] sd 2:0:1:0: [sdb] 320173056 512-byte logical blocks: (163 GB/152 GiB)
[    1.088164] sd 2:0:1:0: [sdb] Write Protect is off
[    1.088175] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[    1.088188]  sda: sda1 sda2 sda3
[    1.088240] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.088913] sd 2:0:0:0: [sda] Attached SCSI disk
[    1.112544]  sdb: sdb1 sdb2 sdb3 < sdb5 > sdb4
[    1.113259] sd 2:0:1:0: [sdb] Attached SCSI disk
[    1.113325] Freeing unused kernel memory: 788k freed
[    1.113789] Write protecting the kernel text: 6260k
[    1.113897] Write protecting the kernel read-only data: 2436k
[    1.137341] udevd[105]: starting version 175
[    1.317594] Disabling lock debugging due to kernel taint
[    1.336425] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    1.336467] 8139cp 0000:03:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    1.337290] 8139too: 8139too Fast Ethernet driver 0.9.28
[    1.338214] 8139too 0000:03:02.0 eth0: RealTek RTL8139 at 0x0001e800, 00:11:2f:95:e4:16, IRQ 21
[    1.428135] usb 5-1: new full-speed USB device number 2 using uhci_hcd
[    1.440089] firewire_ohci 0000:03:01.0: added OHCI v1.0 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[    1.605095] usb 5-1: New USB device found, idVendor=058f, idProduct=9360
[    1.605102] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.605107] usb 5-1: Product: USB Reader
[    1.605110] usb 5-1: Manufacturer: 
[    1.605114] usb 5-1: SerialNumber: 9205291
[    1.608024] tsc: Refined TSC clocksource calibration: 3000.908 MHz
[    1.608032] Switching to clocksource tsc
[    1.848080] usb 5-2: new low-speed USB device number 3 using uhci_hcd
[    1.940195] firewire_core 0000:03:01.0: created device fw0: GUID 00e0180000a02e71, S400
[    2.022109] usb 5-2: New USB device found, idVendor=093a, idProduct=2510
[    2.022122] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.022129] usb 5-2: Product: USB Optical Mouse
[    2.022136] usb 5-2: Manufacturer: PixArt
[    2.034377] Initializing USB Mass Storage driver...
[    2.036116] scsi4 : usb-storage 5-1:1.0
[    2.036772] usbcore: registered new interface driver usb-storage
[    2.036777] USB Mass Storage support registered.
[    2.068218] usbcore: registered new interface driver usbhid
[    2.068224] usbhid: USB HID core driver
[    2.077175] input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2:1.0/input/input3
[    2.077879] hid-generic 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1d.3-2/input0
[    2.114332] EXT3-fs (sdb2): recovery required on readonly filesystem
[    2.114338] EXT3-fs (sdb2): write access will be enabled during recovery
[    3.040134] scsi 4:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[    3.043148] scsi 4:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[    3.046125] scsi 4:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[    3.049121] scsi 4:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[    3.050107] sd 4:0:0:0: Attached scsi generic sg4 type 0
[    3.050485] sd 4:0:0:1: Attached scsi generic sg5 type 0
[    3.050810] sd 4:0:0:2: Attached scsi generic sg6 type 0
[    3.051119] sd 4:0:0:3: Attached scsi generic sg7 type 0
[    3.350119] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[    3.355117] sd 4:0:0:1: [sdd] Attached SCSI removable disk
[    3.360111] sd 4:0:0:2: [sde] Attached SCSI removable disk
[    3.365113] sd 4:0:0:3: [sdf] Attached SCSI removable disk
[    8.027528] kjournald starting.  Commit interval 5 seconds
[    8.035628] EXT3-fs (sdb2): recovery complete
[    8.035634] EXT3-fs (sdb2): mounted filesystem with ordered data mode
[   27.843659] Adding 971896k swap on /dev/sdb1.  Priority:-1 extents:1 across:971896k
[   27.967650] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.024113] udevd[355]: starting version 175
[   29.183673] parport_pc 00:05: reported by Plug and Play ACPI
[   29.183739] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[   29.249814] microcode: CPU0 sig=0xf34, pf=0x10, revision=0x13
[   29.256659] lp: driver loaded but no devices found
[   29.271529] type=1400 audit(1378982721.063:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=587 comm="apparmor_parser"
[   29.271705] type=1400 audit(1378982721.063:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=592 comm="apparmor_parser"
[   29.273298] type=1400 audit(1378982721.067:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=587 comm="apparmor_parser"
[   29.273553] type=1400 audit(1378982721.067:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=592 comm="apparmor_parser"
[   29.274204] type=1400 audit(1378982721.067:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=587 comm="apparmor_parser"
[   29.274477] type=1400 audit(1378982721.067:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=592 comm="apparmor_parser"
[   29.295368] lp0: using parport0 (interrupt-driven).
[   29.316321] intel_rng: FWH not detected
[   29.322273] ppdev: user-space parallel port driver
[   29.609950] microcode: CPU1 sig=0xf34, pf=0x10, revision=0x13
[   29.615643] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[   29.914556] gpio_ich: ACPI BAR is busy, GPI 0 - 15 unavailable
[   29.914567] gpio_ich: GPIO from 206 to 255 on gpio_ich
[   30.209159] Linux video capture interface: v2.00
[   30.228169] bt87x0: Using board 1, analog, digital (rate 32000 Hz)
[   30.461738] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[   30.585594] snd_hda_intel 0000:01:00.1: enabling device (0000 -> 0002)
[   30.585635] hda_intel: Disabling MSI
[   30.585653] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   31.068212] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input4
[   31.068398] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card2/input5
[   31.153098] bttv: driver version 0.9.19 loaded
[   31.153107] bttv: using 8 buffers with 2080k (520 pages) each for capture
[   31.156033] bttv: Bt8xx card found (0)
[   31.156085] bttv: 0: Bt878 (rev 17) at 0000:03:04.0, irq: 16, latency: 64, mmio: 0xdfffe000
[   31.156114] bttv: 0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
[   31.156119] bttv: 0: using: Hauppauge (bt878) [card=10,autodetected]
[   31.158633] bttv: 0: Hauppauge/Voodoo msp34xx: reset line init [5]
[   31.190796] tveeprom 0-0050: Hauppauge model 44806, rev D109, serial# 2661010
[   31.190802] tveeprom 0-0050: tuner model is Philips FI1216MF MK2 (idx 9, type 3)
[   31.190806] tveeprom 0-0050: TV standards PAL(B/G) SECAM(L/L') (eeprom 0x24)
[   31.190810] tveeprom 0-0050: audio processor is None (idx 0)
[   31.190813] tveeprom 0-0050: has no radio
[   31.190816] bttv: 0: Hauppauge eeprom indicates model#44806
[   31.190819] bttv: 0: tuner type=3
[   31.405355] nvidia: module license 'NVIDIA' taints kernel.
[   31.439588] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   31.440142] NVRM: loading NVIDIA UNIX x86 Kernel Module  304.88  Wed Mar 27 14:31:12 PDT 2013
[   31.444360] bttv: 0: audio absent, no audio device found!
[   31.467382] tuner 0-0061: Tuner -1 found with type(s) Radio TV.
[   31.684072] tuner-simple 0-0061: creating new instance
[   31.684082] tuner-simple 0-0061: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF))
[   31.685159] bttv: 0: registered device video0
[   31.685398] bttv: 0: registered device vbi0
[   31.685423] bttv: 0: Setting PLL: 28636363 => 35468950 (needs up to 100ms)
[   31.716039] bttv: PLL set ok
[   32.041619] EXT3-fs (sdb2): using internal journal
[   32.513277] init: failsafe main process (824) killed by TERM signal
[   32.717143] init: udev-fallback-graphics main process (845) terminated with status 1
[   32.878753] type=1400 audit(1378982724.671:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/i386-linux-gnu/lightdm-remote-session-freerdp/freerdp-session-wrapper" pid=947 comm="apparmor_parser"
[   32.879594] type=1400 audit(1378982724.671:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/i386-linux-gnu/lightdm-remote-session-freerdp/freerdp-session-wrapper//chromium_browser" pid=947 comm="apparmor_parser"
[   32.884920] type=1400 audit(1378982724.679:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=946 comm="apparmor_parser"
[   32.886648] type=1400 audit(1378982724.679:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=946 comm="apparmor_parser"
[   33.180480] Bluetooth: Core ver 2.16
[   33.180520] NET: Registered protocol family 31
[   33.180526] Bluetooth: HCI device and connection manager initialized
[   33.180540] Bluetooth: HCI socket layer initialized
[   33.180549] Bluetooth: L2CAP socket layer initialized
[   33.180572] Bluetooth: SCO socket layer initialized
[   33.275946] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   33.275955] Bluetooth: BNEP filters: protocol multicast
[   33.275974] Bluetooth: BNEP socket layer initialized
[   33.310541] Bluetooth: RFCOMM TTY layer initialized
[   33.310565] Bluetooth: RFCOMM socket layer initialized
[   33.310571] Bluetooth: RFCOMM ver 1.11
[   33.712418] init: avahi-cups-reload main process (993) terminated with status 1
[   35.052597] 8139too 0000:03:02.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[   35.084621] WARNING! power/level is deprecated; use power/control instead
[  658.760021] usb 1-5: new high-speed USB device number 4 using ehci-pci
[  658.897137] usb 1-5: New USB device found, idVendor=13fe, idProduct=4100
[  658.897143] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  658.897148] usb 1-5: Product: USB DISK 2.0
[  658.897152] usb 1-5: Manufacturer:         
[  658.897155] usb 1-5: SerialNumber: 070C29F42BC27228
[  658.897593] scsi5 : usb-storage 1-5:1.0
[  659.984386] scsi 5:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 4
[  659.985494] sd 5:0:0:0: Attached scsi generic sg8 type 0
[  661.153653] sd 5:0:0:0: [sdg] 15124992 512-byte logical blocks: (7.74 GB/7.21 GiB)
[  661.154264] sd 5:0:0:0: [sdg] Write Protect is off
[  661.154270] sd 5:0:0:0: [sdg] Mode Sense: 23 00 00 00
[  661.154889] sd 5:0:0:0: [sdg] No Caching mode page present
[  661.154895] sd 5:0:0:0: [sdg] Assuming drive cache: write through
[  661.158641] sd 5:0:0:0: [sdg] No Caching mode page present
[  661.158649] sd 5:0:0:0: [sdg] Assuming drive cache: write through
[  661.178409]  sdg: sdg1
[  661.182281] sd 5:0:0:0: [sdg] No Caching mode page present
[  661.182293] sd 5:0:0:0: [sdg] Assuming drive cache: write through
[  661.182304] sd 5:0:0:0: [sdg] Attached SCSI removable disk
[  760.868022] usb 1-6: new high-speed USB device number 5 using ehci-pci
[  761.002682] usb 1-6: New USB device found, idVendor=13fe, idProduct=3100
[  761.002687] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  761.002692] usb 1-6: Product: USB DISK 2.0
[  761.002696] usb 1-6: Manufacturer:         
[  761.002699] usb 1-6: SerialNumber: 078C1D510068
[  761.003592] scsi6 : usb-storage 1-6:1.0
[  762.039326] scsi 6:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
[  762.040600] sd 6:0:0:0: Attached scsi generic sg9 type 0
[  762.820550] sd 6:0:0:0: [sdh] 7823360 512-byte logical blocks: (4.00 GB/3.73 GiB)
[  762.821160] sd 6:0:0:0: [sdh] Write Protect is off
[  762.821166] sd 6:0:0:0: [sdh] Mode Sense: 23 00 00 00
[  762.821785] sd 6:0:0:0: [sdh] No Caching mode page present
[  762.821790] sd 6:0:0:0: [sdh] Assuming drive cache: write through
[  763.901748] sd 6:0:0:0: [sdh] No Caching mode page present
[  763.901757] sd 6:0:0:0: [sdh] Assuming drive cache: write through
[  763.937382]  sdh: sdh1
[  763.939750] sd 6:0:0:0: [sdh] No Caching mode page present
[  763.939759] sd 6:0:0:0: [sdh] Assuming drive cache: write through
[  763.939767] sd 6:0:0:0: [sdh] Attached SCSI removable disk
[  998.863570] sdg: detected capacity change from 7743995904 to 0
[ 1005.933216] sdh: detected capacity change from 4005560320 to 0
[ 1010.657840] usb 1-6: USB disconnect, device number 5
[ 5787.437533] usb 1-5: USB disconnect, device number 4
[ 5799.680072] usb 1-5: new high-speed USB device number 6 using ehci-pci
[ 5799.816480] usb 1-5: New USB device found, idVendor=05e3, idProduct=0727
[ 5799.816489] usb 1-5: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 5799.816496] usb 1-5: Product: USB Storage
[ 5799.816501] usb 1-5: Manufacturer: Generic
[ 5799.816506] usb 1-5: SerialNumber: 000000000207
[ 5799.824702] scsi7 : usb-storage 1-5:1.0
[ 5800.825415] scsi 7:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0207 PQ: 0 ANSI: 0
[ 5800.826995] sd 7:0:0:0: Attached scsi generic sg8 type 0
[ 5801.162399] sd 7:0:0:0: [sdg] Attached SCSI removable disk
[ 5807.426025] usb 1-5: USB disconnect, device number 6
[ 5847.372048] usb 1-5: new high-speed USB device number 7 using ehci-pci
[ 5847.508605] usb 1-5: New USB device found, idVendor=05e3, idProduct=0727
[ 5847.508615] usb 1-5: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 5847.508621] usb 1-5: Product: USB Storage
[ 5847.508627] usb 1-5: Manufacturer: Generic
[ 5847.508631] usb 1-5: SerialNumber: 000000000207
[ 5847.514451] scsi8 : usb-storage 1-5:1.0
[ 5848.513397] scsi 8:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0207 PQ: 0 ANSI: 0
[ 5848.514805] sd 8:0:0:0: Attached scsi generic sg8 type 0
[ 5848.850400] sd 8:0:0:0: [sdg] Attached SCSI removable disk

Dernière modification par miir83 (Le 12/09/2013, à 13:46)

Hors ligne

#2 Le 12/09/2013, à 20:42

J5012

Re : Clef usb plus reconnue

que raconte utilitaire de disque ?

Hors ligne

#3 Le 12/09/2013, à 20:48

richardgilbert

Re : Clef usb plus reconnue

À mon avis la clé est morte.


Debian, Ubuntu, ElementaryOS, Voyager Linux, Lubuntu & Crunchbang.

Hors ligne

Haut de page ↑