Ubuntu-fr

hedamilt

Re : Configuration WIFI mode console ERROR

ce qui est bizzare c'est que je viens d'avoir accés au fichier log  en FTP root par filezzilla...

Aug 20 13:49:34 localhost kernel: imklog 4.6.4, log source = /proc/kmsg started.
Aug 20 13:49:34 localhost rsyslogd: [origin software="rsyslogd" swVersion="4.6.4" x-pid="967" x-info="http://www.rsyslog.com"] (re)start
Aug 20 13:49:34 localhost kernel: Linux version 2.6.38 (tanzilli@tanzonew) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #28 Tue Oct 25 11:01:32 CEST 2011
Aug 20 13:49:34 localhost kernel: CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Aug 20 13:49:34 localhost kernel: CPU: VIVT data cache, VIVT instruction cache
Aug 20 13:49:34 localhost kernel: Machine: Acme Systems srl FOX Board G20
Aug 20 13:49:34 localhost kernel: Ignoring unrecognised tag 0x00000000
Aug 20 13:49:34 localhost kernel: Memory policy: ECC disabled, Data cache writeback
Aug 20 13:49:34 localhost kernel: Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz
Aug 20 13:49:34 localhost kernel: On node 0 totalpages: 16384
Aug 20 13:49:34 localhost kernel: free_area_init_node: node 0, pgdat c03de168, node_mem_map c03fb000
Aug 20 13:49:34 localhost kernel:  Normal zone: 128 pages used for memmap
Aug 20 13:49:34 localhost kernel:  Normal zone: 0 pages reserved
Aug 20 13:49:34 localhost kernel:  Normal zone: 16256 pages, LIFO batch:3
Aug 20 13:49:34 localhost kernel: pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Aug 20 13:49:34 localhost kernel: pcpu-alloc: [0] 0 
Aug 20 13:49:34 localhost kernel: Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Aug 20 13:49:34 localhost kernel: Kernel command line: mem=64M console=ttyS0,115200 noinitrd root=/dev/mmcblk0p2 rw rootwait init=/sbin/init
Aug 20 13:49:34 localhost kernel:
Aug 20 13:49:34 localhost kernel: PID hash table entries: 256 (order: -2, 1024 bytes)
Aug 20 13:49:34 localhost kernel: Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Aug 20 13:49:34 localhost kernel: Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Aug 20 13:49:34 localhost kernel: Memory: 64MB = 64MB total
Aug 20 13:49:34 localhost kernel: Memory: 60852k/60852k available, 4684k reserved, 0K highmem
Aug 20 13:49:34 localhost kernel: Virtual kernel memory layout:
Aug 20 13:49:34 localhost kernel:    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
Aug 20 13:49:34 localhost kernel:    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
Aug 20 13:49:34 localhost kernel:    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
Aug 20 13:49:34 localhost kernel:    vmalloc : 0xc4800000 - 0xfee00000   ( 934 MB)
Aug 20 13:49:34 localhost kernel:    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
Aug 20 13:49:34 localhost kernel:    modules : 0xbf000000 - 0xc0000000   (  16 MB)
Aug 20 13:49:34 localhost kernel:      .init : 0xc0008000 - 0xc002a000   ( 136 kB)
Aug 20 13:49:34 localhost kernel:      .text : 0xc002a000 - 0xc03bc000   (3656 kB)
Aug 20 13:49:34 localhost kernel:      .data : 0xc03bc000 - 0xc03de960   ( 139 kB)
Aug 20 13:49:34 localhost kernel: NR_IRQS:192
Aug 20 13:49:34 localhost kernel: AT91: 96 gpio irqs in 3 banks
Aug 20 13:49:34 localhost kernel: Console: colour dummy device 80x30
Aug 20 13:49:34 localhost kernel: console [ttyS0] enabled
Aug 20 13:49:34 localhost kernel: Calibrating delay loop... 197.83 BogoMIPS (lpj=989184)
Aug 20 13:49:34 localhost kernel: pid_max: default: 32768 minimum: 301
Aug 20 13:49:34 localhost kernel: Mount-cache hash table entries: 512
Aug 20 13:49:34 localhost kernel: CPU: Testing write buffer coherency: ok
Aug 20 13:49:34 localhost kernel: NET: Registered protocol family 16
Aug 20 13:49:34 localhost kernel: AT91: Power Management (with slow clock mode)
Aug 20 13:49:34 localhost kernel: AT91: Starting after general reset
Aug 20 13:49:34 localhost kernel: tcb_clksrc: tc0 at 16.012 MHz
Aug 20 13:49:34 localhost kernel: bio: create slab <bio-0> at 0
Aug 20 13:49:34 localhost kernel: SCSI subsystem initialized
Aug 20 13:49:34 localhost kernel: usbcore: registered new interface driver usbfs
Aug 20 13:49:34 localhost kernel: usbcore: registered new interface driver hub
Aug 20 13:49:34 localhost kernel: usbcore: registered new device driver usb
Aug 20 13:49:34 localhost kernel: i2c-gpio i2c-gpio: using pins 55 (SDA) and 56 (SCL)
Aug 20 13:49:34 localhost kernel: Switching to clocksource tcb_clksrc
Aug 20 13:49:34 localhost kernel: Switched to NOHz mode on CPU #0
Aug 20 13:49:34 localhost kernel: NET: Registered protocol family 2
Aug 20 13:49:34 localhost kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Aug 20 13:49:34 localhost kernel: TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Aug 20 13:49:34 localhost kernel: TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Aug 20 13:49:34 localhost kernel: TCP: Hash tables configured (established 2048 bind 2048)
Aug 20 13:49:34 localhost kernel: TCP reno registered
Aug 20 13:49:34 localhost kernel: UDP hash table entries: 256 (order: 0, 4096 bytes)
Aug 20 13:49:34 localhost kernel: UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Aug 20 13:49:34 localhost kernel: NET: Registered protocol family 1
Aug 20 13:49:34 localhost kernel: NetWinder Floating Point Emulator V0.97 (double precision)
Aug 20 13:49:34 localhost kernel: VFS: Disk quotas dquot_6.5.2
Aug 20 13:49:34 localhost kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Aug 20 13:49:34 localhost kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
Aug 20 13:49:34 localhost kernel: JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
Aug 20 13:49:34 localhost kernel: msgmni has been set to 118
Aug 20 13:49:34 localhost kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
Aug 20 13:49:34 localhost kernel: io scheduler noop registered (default)
Aug 20 13:49:34 localhost kernel: atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
Aug 20 13:49:34 localhost kernel: atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
Aug 20 13:49:34 localhost kernel: atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
Aug 20 13:49:34 localhost kernel: atmel_usart.3: ttyS3 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
Aug 20 13:49:34 localhost kernel: atmel_usart.4: ttyS4 at MMIO 0xfffd0000 (irq = 23) is a ATMEL_SERIAL
Aug 20 13:49:34 localhost kernel: brd: module loaded
Aug 20 13:49:34 localhost kernel: loop: module loaded
Aug 20 13:49:34 localhost kernel: MACB_mii_bus: probed
Aug 20 13:49:34 localhost kernel: eth0: Atmel MACB at 0xfffc4000 irq 21 (00:04:25:28:2d:b2)
Aug 20 13:49:34 localhost kernel: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:03, irq=-1)
Aug 20 13:49:34 localhost kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Aug 20 13:49:34 localhost kernel: at91_ohci at91_ohci: AT91 OHCI
Aug 20 13:49:34 localhost kernel: at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
Aug 20 13:49:34 localhost kernel: at91_ohci at91_ohci: irq 20, io mem 0x00500000
Aug 20 13:49:34 localhost kernel: hub 1-0:1.0: USB hub found
Aug 20 13:49:34 localhost kernel: hub 1-0:1.0: 2 ports detected
Aug 20 13:49:34 localhost kernel: Initializing USB Mass Storage driver...
Aug 20 13:49:34 localhost kernel: usbcore: registered new interface driver usb-storage
Aug 20 13:49:34 localhost kernel: USB Mass Storage support registered.
Aug 20 13:49:34 localhost kernel: udc: at91_udc version 3 May 2006
Aug 20 13:49:34 localhost kernel: mousedev: PS/2 mouse device common for all mice
Aug 20 13:49:34 localhost kernel: input: gpio-keys as /devices/platform/gpio-keys/input/input0
Aug 20 13:49:34 localhost kernel: at91_rtt: dev (254:0)
Aug 20 13:49:34 localhost kernel: rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
Aug 20 13:49:34 localhost kernel: i2c /dev entries driver
Aug 20 13:49:34 localhost kernel: Driver for 1-wire Dallas network protocol.
Aug 20 13:49:34 localhost kernel: AT91SAM9 Watchdog: sorry, watchdog is disabled
Aug 20 13:49:34 localhost kernel: at91_wdt: probe of at91_wdt failed with error -5
Aug 20 13:49:34 localhost kernel: cpuidle: using governor ladder
Aug 20 13:49:34 localhost kernel: cpuidle: using governor menu
Aug 20 13:49:34 localhost kernel: Registered led device: user_led
Aug 20 13:49:34 localhost kernel: usbcore: registered new interface driver usbhid
Aug 20 13:49:34 localhost kernel: usbhid: USB HID core driver
Aug 20 13:49:34 localhost kernel: TCP cubic registered
Aug 20 13:49:34 localhost kernel: NET: Registered protocol family 17
Aug 20 13:49:34 localhost kernel: rtc-at91sam9 at91_rtt.0: readtime: 2010-07-20 11:49:09
Aug 20 13:49:34 localhost kernel: rtc-at91sam9 at91_rtt.0: setting system clock to 2010-08-20 11:49:09 UTC (1282304949)
Aug 20 13:49:34 localhost kernel: Waiting for root device /dev/mmcblk0p2...
Aug 20 13:49:34 localhost kernel: mmc0: host does not support reading read-only switch. assuming write-enable.
Aug 20 13:49:34 localhost kernel: mmc0: new SDHC card at address 0001
Aug 20 13:49:34 localhost kernel: mmcblk0: mmc0:0001 00000 7.41 GiB 
Aug 20 13:49:34 localhost kernel: mmcblk0: p1 p2 p3 p4
Aug 20 13:49:34 localhost kernel: EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240)
Aug 20 13:49:34 localhost kernel: EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244)
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): ext4_orphan_cleanup: deleting unreferenced inode 47170
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): 1 orphan inode deleted
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): recovery complete
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Aug 20 13:49:34 localhost kernel: VFS: Mounted root (ext4 filesystem) on device 179:2.
Aug 20 13:49:34 localhost kernel: Freeing init memory: 136K
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Aug 20 13:49:34 localhost kernel: EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
Aug 20 13:49:34 localhost kernel: eth0: link up (100/Full)
Aug 20 13:49:35 localhost /usr/sbin/cron[1014]: (CRON) INFO (pidfile fd = 3)
Aug 20 13:49:35 localhost /usr/sbin/cron[1018]: (CRON) STARTUP (fork ok)
Aug 20 13:49:35 localhost /usr/sbin/cron[1018]: (CRON) INFO (Running @reboot jobs)
Aug 20 13:49:38 localhost kernel: NET: Registered protocol family 10
Aug 20 13:49:38 localhost kernel: sshd (1049): /proc/1049/oom_adj is deprecated, please use /proc/1049/oom_score_adj instead.
Aug 20 13:49:49 localhost kernel: eth0: no IPv6 routers present
Aug 20 13:50:37 localhost kernel: usb 1-2: new full speed USB device using at91_ohci and address 2
Aug 20 13:50:38 localhost kernel: cfg80211: Calling CRDA to update world regulatory domain
Aug 20 13:50:39 localhost kernel: ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Aug 20 13:50:39 localhost kernel: Registered led device: rt73usb-phy0::radio
Aug 20 13:50:39 localhost kernel: Registered led device: rt73usb-phy0::assoc
Aug 20 13:50:39 localhost kernel: Registered led device: rt73usb-phy0::quality
Aug 20 13:50:39 localhost kernel: usbcore: registered new interface driver rt73usb

Dernière modification par hedamilt (Le 26/02/2014, à 21:34)

hedamilt

Re : Configuration WIFI mode console ERROR

Personne pour m'aidé ?

cromanion

Re : Configuration WIFI mode console ERROR

Si je veux bien t'aider !
mais tu tournes autour du pot.

voici un fichier "etc/network/interfaces" que je te propose:

auto lo
iface lo inet loopback

auto eth0
iface eth0 inet dhcp

auto wlan0
iface wlan0 inet dhcp

# canal 6
wireless-freq 2.437G

wpa-mode managed
wpa-ap-scan 1
wpa-scan-ssid 1
wpa-key-mgmt WPA-PSK
wpa-group CCMP
wpa-bssid 00:24:D4:9E:1C:EC
wpa-ssid Freebox-41C81C
wpa-psk --> ta clé que tu dois connaitre <--

Come tu peux le voir, tu ne places aucun "=" ou  " " dans le script interfaces ci-dessus.

Suivant que tu utilises soit eth0 soit wlan0 ou les deux (comme ici: auto eth0 ou wlan0), tu vires la
ligne corespondante ou tu vires rien.

Tu vires le wpa_supplicant.conf (trop technique).
Tu vires tous les utilitaires qui t'aides à te connecter (nework-manager compris)

Tu fais les commandes:

sudo ifdown --verbose wlan0
sudo ifup --verbose wlan0
sudo iwconfig wlan0

Si ça marche pas:
Dans ta freebox, change ton groupe CCMP par du groupe TKIP, si c'est possible.
Ou alors, c'est qu'il y a une anomalie dans ton architecture.

Dernière modification par cromanion (Le 09/03/2014, à 16:39)