Pages : 1
#1 Le 17/06/2014, à 17:31
- Astrolivier
pb disque dur, analyse smartctl
Salut,
Suite à ce sujet : http://forum.ubuntu-fr.org/viewtopic.php?id=1599911
je me décide à faire un autre sujet, pour avoir confirmation que le disque dur de mes amis est en train de mourir (ou autre information) :
smartclt :
Aspire-5736Z:~$ sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.0-29-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K250
Device Model: Hitachi HTS542516K9SA00
Serial Number: 081004BB6300HCGYZTNF
LU WWN Device Id: 5 000cca 592cda25d
Firmware Version: BBCOC33P
User Capacity: 160 041 885 696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 3f
SATA Version is: SATA 2.5, 1.5 Gb/s
Local Time is: Thu Jun 12 13:43:12 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 75) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 094 094 062 Pre-fail Always - 1835009
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 241 241 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 098 098 000 Old_age Always - 3570
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3848
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 3413
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 127
193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 22939
194 Temperature_Celsius 0x0002 177 177 000 Old_age Always - 31 (Min/Max 5/54)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 143
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 23
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 67 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 67 occurred at disk power-on lifetime: 2691 hours (112 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 8a a1 96 e0 Error: UNC at LBA = 0x0096a18a = 9871754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
29 ff 7f 20 a1 96 e0 00 00:01:01.000 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:56.900 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:52.800 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:48.600 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:44.500 READ MULTIPLE EXT
Error 66 occurred at disk power-on lifetime: 2691 hours (112 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 8a a1 96 e0 Error: UNC 21 sectors at LBA = 0x0096a18a = 9871754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 ff 7f 20 a1 96 e0 00 00:00:56.900 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:52.800 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:48.600 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:44.500 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:40.400 READ DMA EXT
Error 65 occurred at disk power-on lifetime: 2691 hours (112 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 8a a1 96 e0 Error: UNC at LBA = 0x0096a18a = 9871754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
29 ff 7f 20 a1 96 e0 00 00:00:52.800 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:48.600 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:44.500 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:40.400 READ DMA EXT
25 ff 62 a6 b8 6b e0 00 00:00:40.400 READ DMA EXT
Error 64 occurred at disk power-on lifetime: 2691 hours (112 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 8a a1 96 e0 Error: UNC 21 sectors at LBA = 0x0096a18a = 9871754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 ff 7f 20 a1 96 e0 00 00:00:48.600 READ DMA EXT
29 ff 7f 20 a1 96 e0 00 00:00:44.500 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:40.400 READ DMA EXT
25 ff 62 a6 b8 6b e0 00 00:00:40.400 READ DMA EXT
25 ff 7f 27 b8 6b e0 00 00:00:40.400 READ DMA EXT
Error 63 occurred at disk power-on lifetime: 2691 hours (112 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 8a a1 96 e0 Error: UNC at LBA = 0x0096a18a = 9871754
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
29 ff 7f 20 a1 96 e0 00 00:00:44.500 READ MULTIPLE EXT
25 ff 7f 20 a1 96 e0 00 00:00:40.400 READ DMA EXT
25 ff 62 a6 b8 6b e0 00 00:00:40.400 READ DMA EXT
25 ff 7f 27 b8 6b e0 00 00:00:40.400 READ DMA EXT
25 ff 7f a8 b7 6b e0 00 00:00:40.400 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.je précise que j'ai aussi fait un fsck, mais qu'il ne m'a rien renvoyé
bien à vous
S'il faut absolument faire des sacrifices pour assurer le progrès de l'humanité, ne serait-il pas indispensable de s'en tenir au principe selon lequel c'est à ceux dont on exige le sacrifice que la décision doit revenir en dernier ressort ? (howard zinn)
Hors ligne
#2 Le 17/06/2014, à 18:37
- jacobus77
Re : pb disque dur, analyse smartctl
Si tu ne veux pas interprêter les données "brutes", tu peux utiliser gsmartcontrol ça te facilitera la tâche.
Hors ligne
Pages : 1