Pages : 1
#1 Le 03/02/2008, à 11:07
- seb_68
Problème au boot
Bonjour,
Cela fait plus d'un an que je suis sous Ubuntu et j'en suis ravi.
Cependant depuis 2 ou 3 jours, j'ai un problème et malgré mes recherches sous google, je ne trouve pas LA solution car je n'arrive pas à savoir quelle en est la cause.
Comme tout le monde, j'aimerais eviter de formater car je voudrais recupérer mes fichiers.
Hélas, je n'ai pas mis mon dossier /home sur 1 partition seule.
Tout d'abord, je tiens à preciser que je suis utilisateur de Ubuntu et pas programmateur ou informaticien donc mes comptétences sont très limitées.
Voilà :
lorsque j'allume mon pc, il m'affiche un message d'erreur:
Busybox v1-1. 3 (Debian ....... Ubuntu7) Built-in shell (ash)
Enter « help » for a list ......
initramsf >
A savoir que je suis en RAID 0
1-J'ai fait 1 memtest --> 2 passes, aucun problème
2-J'ai testé mes 2 DD Seagate avec leur logiciel de boot --> Aucun problème
3-J'ai voulu essayer TESTDISK avec systemrescuecd:
Voici le message d'erreur obtenu peu apres avoir booter sur le livecd:
disabled for 5 mintues init:ID respawning too fast:disabled for 5 mintues no more processes left in this runlevel
(Il y a 1 numéro apres ID mais je ne m 'en souviens plus, je peux vous le dire au besoin)
--> Et toutes les 5minutes, il cherche puis réécrit ce message
4- J'ai booté à partir sur livecd d'ubuntu pour arriver à la console afin de faire 1 fsck.
J'ai, suite à fdisk -l, ces partitions:
sda1; sda2; sda3; sdb1; sdb2
(je me rappelle plus des détails mais m'indique, il me semble un message d'erreur en md0 (???)
j'ai essayé:
sudo umount /dev/sdb1
sudo fsck /dev/sdb1
Et la j'ai le message :
« Le superbloc ou la table des partitions est peut etre corrompue »
Pour plus de détail, n'hesitez pas à me demander en me precisant les commandes à réaliser.
Merci de votre précieuse aide car je ne sais plus quoi faire...
Hors ligne
#2 Le 03/02/2008, à 11:10
- HymnToLife
Re : Problème au boot
RAID logiciel ou matériel ?
- Rodrigue, as-tu du cœur ?
- Non, mais j'ai du pique !
Hors ligne
#3 Le 03/02/2008, à 11:13
- seb_68
Re : Problème au boot
Materiel je pense, ce sont 2 disques durs identiques
Hors ligne
#4 Le 03/02/2008, à 12:22
- seb_68
Re : Problème au boot
Voici le resultat de lspci, lshw et dmesg: (Mon dieu comment peut-on comprendre ce "chinois"?)
ubuntu@ubuntu:~$ lspci
00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
00:05.0 Multimedia audio controller: nVidia Corporation nForce Audio Processing Unit (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3)
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev a3)
00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE 1394) Controller (rev a3)
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
01:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02)
02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB Integrated Fast Ethernet Controller [Tornado] (rev 40)
03:00.0 VGA compatible controller: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
03:00.1 Display controller: ATI Technologies Inc Radeon R300 [Radeon 9500 Pro] (Secondary)
ubuntu@ubuntu:~$
ubuntu@ubuntu:~$ lshw
WARNING: you should run this program as super-user.
ubuntu
description: Computer
width: 32 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 0
size: 1011MB
*-cpu
product: AMD Athlon(tm) XP 2600+
vendor: Advanced Micro Devices [AMD]
physical id: 1
bus info: cpu@0
version: 6.8.1
size: 2100MHz
width: 32 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow up ts
*-cache:0
description: L1 cache
physical id: 0
size: 128KB
*-cache:1
description: L2 cache
physical id: 1
size: 256KB
*-pci
description: Host bridge
product: nForce2 AGP (different version?)
vendor: nVidia Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: c1
width: 32 bits
clock: 66MHz
configuration: driver=agpgart-nvidia module=nvidia_agp
*-memory:0 UNCLAIMED
description: RAM memory
product: nForce2 Memory Controller 1
vendor: nVidia Corporation
physical id: 0.1
bus info: pci@0000:00:00.1
version: c1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:1 UNCLAIMED
description: RAM memory
product: nForce2 Memory Controller 4
vendor: nVidia Corporation
physical id: 0.2
bus info: pci@0000:00:00.2
version: c1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:2 UNCLAIMED
description: RAM memory
product: nForce2 Memory Controller 3
vendor: nVidia Corporation
physical id: 0.3
bus info: pci@0000:00:00.3
version: c1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:3 UNCLAIMED
description: RAM memory
product: nForce2 Memory Controller 2
vendor: nVidia Corporation
physical id: 0.4
bus info: pci@0000:00:00.4
version: c1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:4 UNCLAIMED
description: RAM memory
product: nForce2 Memory Controller 5
vendor: nVidia Corporation
physical id: 0.5
bus info: pci@0000:00:00.5
version: c1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-isa
description: ISA bridge
product: nForce2 ISA Bridge
vendor: nVidia Corporation
physical id: 1
bus info: pci@0000:00:01.0
version: a4
width: 32 bits
clock: 66MHz
capabilities: isa bus_master cap_list
configuration: latency=0
*-serial
description: SMBus
product: nForce2 SMBus (MCP)
vendor: nVidia Corporation
physical id: 1.1
bus info: pci@0000:00:01.1
version: a2
width: 32 bits
clock: 66MHz
capabilities: cap_list
configuration: driver=nForce2_smbus latency=0 maxlatency=1 mingnt=3 module=i2c_nforce2
*-usb:0
description: USB Controller
product: nForce2 USB Controller
vendor: nVidia Corporation
physical id: 2
bus info: pci@0000:00:02.0
version: a4
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd latency=0 maxlatency=1 mingnt=3 module=ohci_hcd
*-usb:1
description: USB Controller
product: nForce2 USB Controller
vendor: nVidia Corporation
physical id: 2.1
bus info: pci@0000:00:02.1
version: a4
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd latency=0 maxlatency=1 mingnt=3 module=ohci_hcd
*-usb:2
description: USB Controller
product: nForce2 USB Controller
vendor: nVidia Corporation
physical id: 2.2
bus info: pci@0000:00:02.2
version: a4
width: 32 bits
clock: 66MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 maxlatency=1 mingnt=3 module=ehci_hcd
*-network
description: Ethernet interface
product: nForce2 Ethernet Controller
vendor: nVidia Corporation
physical id: 4
bus info: pci@0000:00:04.0
logical name: eth0
version: a1
serial: 00:0c:6e:2b:d8:88
width: 32 bits
clock: 66MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=forcedeth driverversion=0.60 latency=0 maxlatency=20 mingnt=1 module=forcedeth multicast=yes
*-multimedia:0 UNCLAIMED
description: Multimedia audio controller
product: nForce Audio Processing Unit
vendor: nVidia Corporation
physical id: 5
bus info: pci@0000:00:05.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: bus_master cap_list
configuration: latency=0 maxlatency=12 mingnt=1
*-multimedia:1
description: Multimedia audio controller
product: nForce2 AC97 Audio Controler (MCP)
vendor: nVidia Corporation
physical id: 6
bus info: pci@0000:00:06.0
version: a1
width: 32 bits
clock: 66MHz
capabilities: bus_master cap_list
configuration: driver=Intel ICH latency=0 maxlatency=5 mingnt=2 module=snd_intel8x0
*-pci:0
description: PCI bridge
product: nForce2 External PCI Bridge
vendor: nVidia Corporation
physical id: 8
bus info: pci@0000:00:08.0
version: a3
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-storage
description: RAID bus controller
product: SiI 3112 [SATALink/SATARaid] Serial ATA Controller
vendor: Silicon Image, Inc.
physical id: b
bus info: pci@0000:01:0b.0
version: 02
width: 32 bits
clock: 66MHz
capabilities: storage bus_master cap_list
configuration: driver=sata_sil latency=32 module=sata_sil
*-ide
description: IDE interface
product: nForce2 IDE
vendor: nVidia Corporation
physical id: 9
bus info: pci@0000:00:09.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: ide bus_master cap_list
configuration: driver=AMD_IDE latency=0 maxlatency=1 mingnt=3 module=amd74xx
*-ide:0
description: IDE Channel 0
physical id: 0
bus info: ide@0
logical name: ide0
clock: 66MHz
*-cdrom
product: PLEXTOR CD-R PX-W4824A
physical id: 0
bus info: ide@0.0
logical name: /dev/hda
capabilities: packet
*-ide:1
description: IDE Channel 1
physical id: 1
bus info: ide@1
logical name: ide1
clock: 66MHz
*-cdrom
product: LITE-ON DVDRW SOHW-1633S
physical id: 1
bus info: ide@1.1
logical name: /dev/hdd
capacity: 695MB
capabilities: packet
*-pci:1
description: PCI bridge
product: nForce2 PCI Bridge
vendor: nVidia Corporation
physical id: c
bus info: pci@0000:00:0c.0
version: a3
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-network
description: Ethernet interface
product: 3C920B-EMB Integrated Fast Ethernet Controller [Tornado]
vendor: 3Com Corporation
physical id: 1
bus info: pci@0000:02:01.0
logical name: eth1
version: 40
serial: 00:26:54:0b:fb:5a
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=3c59x latency=32 maxlatency=10 mingnt=10 module=3c59x multicast=yes
*-firewire
description: FireWire (IEEE 1394)
product: nForce2 FireWire (IEEE 1394) Controller
vendor: nVidia Corporation
physical id: d
bus info: pci@0000:00:0d.0
version: a3
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci1394 latency=0 maxlatency=1 mingnt=3 module=ohci1394
*-pci:2
description: PCI bridge
product: nForce2 AGP
vendor: nVidia Corporation
physical id: 1e
bus info: pci@0000:00:1e.0
version: c1
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-display:0
description: VGA compatible controller
product: Radeon R300 NE [Radeon 9500 Pro]
vendor: ATI Technologies Inc
physical id: 0
bus info: pci@0000:03:00.0
version: 00
width: 32 bits
clock: 66MHz
capabilities: vga bus_master cap_list
configuration: latency=32 mingnt=8
*-display:1 UNCLAIMED
description: Display controller
product: Radeon R300 [Radeon 9500 Pro] (Secondary)
vendor: ATI Technologies Inc
physical id: 0.1
bus info: pci@0000:03:00.1
version: 00
width: 32 bits
clock: 66MHz
capabilities: cap_list
configuration: latency=32 mingnt=8
*-scsi
physical id: 1
bus info: scsi@2
logical name: scsi2
capabilities: scsi-host
configuration: driver=usb-storage
*-network
description: Wireless interface
physical id: 2
logical name: eth2
serial: 00:60:b3:e7:2a:f4
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=IEEE 802.11b/g
ubuntu@ubuntu:~$
ubuntu@ubuntu:~$ dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262128
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262128
[ 0.000000] On node 0 totalpages: 262128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32497 pages, LIFO batch:7
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6D80 checksum 0
[ 0.000000] ACPI: RSDP 000F6D80, 0014 (r0 Nvidia)
[ 0.000000] ACPI: RSDT 3FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 3FFF30C0, 440A (r1 NVIDIA AWRDACPI 1000 MSFT 100000E)
[ 0.000000] ACPI: FACS 3FFF0000, 0040
[ 0.000000] ACPI: APIC 3FFF7500, 005A (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[ 0.000000] Built 1 zonelists. Total pages: 260081
[ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- locale=fr_FR console-setup/layoutcode=fr console-setup/variantcode=oss
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2079.536 MHz processor.
[ 56.692909] Console: colour VGA+ 80x25
[ 56.693493] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 56.694493] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 56.722215] Memory: 1027624k/1048512k available (2015k kernel code, 20172k reserved, 916k data, 364k init, 131008k highmem)
[ 56.722225] virtual kernel memory layout:
[ 56.722226] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 56.722228] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 56.722229] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 56.722230] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 56.722232] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 56.722233] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 56.722234] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 56.722238] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 56.722283] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 56.802241] Calibrating delay using timer specific routine.. 4162.40 BogoMIPS (lpj=8324805)
[ 56.802277] Security Framework v1.0.0 initialized
[ 56.802284] SELinux: Disabled at boot.
[ 56.802301] Mount-cache hash table entries: 512
[ 56.802458] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
[ 56.802467] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 56.802470] CPU: L2 Cache: 256K (64 bytes/line)
[ 56.802473] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
[ 56.802485] Compat vDSO mapped to ffffe000.
[ 56.802498] Checking 'hlt' instruction... OK.
[ 56.818382] SMP alternatives: switching to UP code
[ 56.818666] Freeing SMP alternatives: 11k freed
[ 56.819015] Early unpacking initramfs... done
[ 57.126200] ACPI: Core revision 20070126
[ 57.126292] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 57.128829] CPU0: AMD Athlon(tm) XP 2600+ stepping 01
[ 57.128850] Total of 1 processors activated (4162.40 BogoMIPS).
[ 57.129048] ENABLING IO-APIC IRQs
[ 57.129239] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 57.273935] Brought up 1 CPUs
[ 57.274069] Booting paravirtualized kernel on bare hardware
[ 57.274136] Time: 10:10:30 Date: 01/03/108
[ 57.274166] NET: Registered protocol family 16
[ 57.274270] EISA bus registered
[ 57.274284] ACPI: bus type pci registered
[ 57.306279] PCI: PCI BIOS revision 2.10 entry at 0xfb490, last bus=3
[ 57.306281] PCI: Using configuration type 1
[ 57.306283] Setting up standard PCI resources
[ 57.311648] ACPI: EC: Look up EC in DSDT
[ 57.316011] ACPI: Interpreter enabled
[ 57.316015] ACPI: (supports S0 S1 S4 S5)
[ 57.316030] ACPI: Using IOAPIC for interrupt routing
[ 57.324310] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 57.324321] PCI: Probing PCI hardware (bus 00)
[ 57.324400] PCI: nForce2 C1 Halt Disconnect fixup
[ 57.325364] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 57.325514] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 57.325725] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 57.325814] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB1._PRT]
[ 57.373943] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.374080] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.374214] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 57.374347] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 57.374478] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.374611] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 57.374743] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 57.374875] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 57.375006] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 57.375144] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 57.375276] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.375408] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.375549] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 57.375681] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 57.375815] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 57.375949] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 57.376067] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
[ 57.376170] ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
[ 57.376273] ACPI: PCI Interrupt Link [APC3] (IRQs *18)
[ 57.376375] ACPI: PCI Interrupt Link [APC4] (IRQs *19)
[ 57.376483] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 57.376634] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
[ 57.376782] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
[ 57.376930] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
[ 57.377076] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
[ 57.377223] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
[ 57.377370] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
[ 57.377474] ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
[ 57.377620] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
[ 57.377768] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0
[ 57.377930] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0
[ 57.378079] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
[ 57.378191] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 57.378204] pnp: PnP ACPI init
[ 57.378218] ACPI: bus type pnp registered
[ 57.382722] pnp: PnP ACPI: found 16 devices
[ 57.382726] ACPI: ACPI bus type pnp unregistered
[ 57.382730] PnPBIOS: Disabled by ACPI PNP
[ 57.382794] PCI: Using ACPI for IRQ routing
[ 57.382800] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 57.447734] NET: Registered protocol family 8
[ 57.447736] NET: Registered protocol family 20
[ 57.447811] pnp: 00:00: ioport range 0x4000-0x407f has been reserved
[ 57.447815] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[ 57.447818] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[ 57.447821] pnp: 00:00: ioport range 0x4480-0x44ff has been reserved
[ 57.447823] pnp: 00:00: ioport range 0x4200-0x427f has been reserved
[ 57.447826] pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
[ 57.447833] pnp: 00:01: ioport range 0x5000-0x503f has been reserved
[ 57.447836] pnp: 00:01: ioport range 0x5500-0x553f has been reserved
[ 57.447842] pnp: 00:02: iomem range 0xd7800-0xd7fff has been reserved
[ 57.447845] pnp: 00:02: iomem range 0xf0000-0xf7fff could not be reserved
[ 57.447847] pnp: 00:02: iomem range 0xf8000-0xfbfff could not be reserved
[ 57.447850] pnp: 00:02: iomem range 0xfc000-0xfffff could not be reserved
[ 57.449752] Time: tsc clocksource has been installed.
[ 57.478162] PCI: Bridge: 0000:00:08.0
[ 57.478165] IO window: 9000-afff
[ 57.478171] MEM window: e8000000-e9ffffff
[ 57.478175] PREFETCH window: 50000000-500fffff
[ 57.478180] PCI: Bridge: 0000:00:0c.0
[ 57.478182] IO window: b000-bfff
[ 57.478187] MEM window: e4000000-e5ffffff
[ 57.478190] PREFETCH window: 50100000-501fffff
[ 57.478196] PCI: Bridge: 0000:00:1e.0
[ 57.478198] IO window: c000-cfff
[ 57.478202] MEM window: e6000000-e7ffffff
[ 57.478206] PREFETCH window: d0000000-dfffffff
[ 57.478217] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 57.478224] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 57.478240] NET: Registered protocol family 2
[ 57.517757] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 57.517936] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 57.519945] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 57.520672] TCP: Hash tables configured (established 131072 bind 65536)
[ 57.520676] TCP reno registered
[ 57.529836] checking if image is initramfs... it is
[ 57.981360] Switched to high resolution mode on CPU 0
[ 58.110040] Freeing initrd memory: 7305k freed
[ 58.110488] audit: initializing netlink socket (disabled)
[ 58.110503] audit(1202033431.124:1): initialized
[ 58.110573] highmem bounce pool size: 64 pages
[ 58.112392] VFS: Disk quotas dquot_6.5.1
[ 58.112457] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 58.112557] io scheduler noop registered
[ 58.112560] io scheduler anticipatory registered
[ 58.112562] io scheduler deadline registered
[ 58.112575] io scheduler cfq registered (default)
[ 58.112623] Boot video device is 0000:03:00.0
[ 58.112818] isapnp: Scanning for PnP cards...
[ 58.467011] isapnp: No Plug & Play device found
[ 58.500114] Real Time Clock Driver v1.12ac
[ 58.500221] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 58.500338] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 58.500628] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 58.501523] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 58.501932] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 58.502758] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 58.502995] input: Macintosh mouse button emulation as /class/input/input0
[ 58.503074] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 58.503077] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 58.752972] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 58.753163] mice: PS/2 mouse device common for all mice
[ 58.753291] EISA: Probing bus 0 at eisa.0
[ 58.753314] Cannot allocate resource for EISA slot 4
[ 58.753317] Cannot allocate resource for EISA slot 5
[ 58.753332] EISA: Detected 0 cards.
[ 58.753437] TCP cubic registered
[ 58.753446] NET: Registered protocol family 1
[ 58.753467] Using IPI No-Shortcut mode
[ 58.753674] Magic number: 12:872:172
[ 58.754321] Freeing unused kernel memory: 364k freed
[ 58.796608] input: AT Translated Set 2 keyboard as /class/input/input1
[ 59.965881] AppArmor: AppArmor initialized<5>audit(1202033433.124:2): type=1505 info="AppArmor initialized" pid=1224
[ 59.974494] fuse init (API version 7.8)
[ 59.980544] Failure registering capabilities with primary security module.
[ 60.641730] usbcore: registered new interface driver usbfs
[ 60.641760] usbcore: registered new interface driver hub
[ 60.641784] usbcore: registered new device driver usb
[ 60.642595] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 60.642949] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
[ 60.642958] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IRQ 16
[ 60.642973] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 60.642977] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 60.643194] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 60.643216] ohci_hcd 0000:00:02.0: irq 16, io mem 0xea087000
[ 60.704953] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 60.716976] usb usb1: configuration #1 chosen from 1 choice
[ 60.717010] hub 1-0:1.0: USB hub found
[ 60.717023] hub 1-0:1.0: 3 ports detected
[ 60.744597] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 60.744604] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 60.819181] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
[ 60.819193] ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [APCG] -> GSI 21 (level, high) -> IRQ 17
[ 60.819210] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 60.819214] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 60.819248] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 60.819269] ohci_hcd 0000:00:02.1: irq 17, io mem 0xea082000
[ 60.876820] usb usb2: configuration #1 chosen from 1 choice
[ 60.876852] hub 2-0:1.0: USB hub found
[ 60.876865] hub 2-0:1.0: 3 ports detected
[ 60.897493] SCSI subsystem initialized
[ 60.902662] libata version 2.21 loaded.
[ 60.920327] Floppy drive(s): fd0 is 1.44M
[ 60.969825] FDC 0 is a post-1991 82077
[ 60.979592] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
[ 60.979605] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 20 (level, high) -> IRQ 18
[ 60.979612] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 61.122435] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 61.202363] end_request: I/O error, dev fd0, sector 0
[ 61.335316] usb 1-2: configuration #1 chosen from 1 choice
[ 61.498351] eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
[ 61.498823] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 61.498828] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 16
[ 61.498842] PCI: Setting latency timer of device 0000:00:02.2 to 64
[ 61.498846] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 61.498880] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
[ 61.498919] ehci_hcd 0000:00:02.2: debug port 1
[ 61.498924] PCI: cache line size of 64 is not supported by device 0000:00:02.2
[ 61.498933] ehci_hcd 0000:00:02.2: irq 16, io mem 0xea083000
[ 61.641957] usb 2-2: new low speed USB device using ohci_hcd and address 2
[ 61.641986] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 61.642127] usb usb3: configuration #1 chosen from 1 choice
[ 61.642155] hub 3-0:1.0: USB hub found
[ 61.642166] hub 3-0:1.0: 6 ports detected
[ 61.746086] NFORCE2: IDE controller at PCI slot 0000:00:09.0
[ 61.746114] NFORCE2: chipset revision 162
[ 61.746116] NFORCE2: not 100% native mode: will probe irqs later
[ 61.746124] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
[ 61.746135] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 61.746147] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 61.746156] Probing IDE interface ide0...
[ 61.829795] usb 1-2: USB disconnect, address 2
[ 62.197452] usb 3-2: new high speed USB device using ehci_hcd and address 2
[ 62.237427] end_request: I/O error, dev fd0, sector 0
[ 62.330201] usb 3-2: configuration #1 chosen from 1 choice
[ 62.481313] hda: PLEXTOR CD-R PX-W4824A, ATAPI CD/DVD-ROM drive
[ 62.816891] usb 2-2: new low speed USB device using ohci_hcd and address 3
[ 62.817090] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 62.818469] Probing IDE interface ide1...
[ 63.039580] usb 2-2: configuration #1 chosen from 1 choice
[ 63.054477] usbcore: registered new interface driver hiddev
[ 63.061893] input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
[ 63.062032] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-2
[ 63.062049] usbcore: registered new interface driver usbhid
[ 63.062053] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 63.272492] end_request: I/O error, dev fd0, sector 0
[ 63.832091] hdd: LITE-ON DVDRW SOHW-1633S, ATAPI CD/DVD-ROM drive
[ 63.888501] ide1 at 0x170-0x177,0x376 on irq 15
[ 63.892494] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21
[ 63.892501] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 21 (level, high) -> IRQ 17
[ 63.892509] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 63.945438] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[ea084000-ea0847ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 63.952041] sata_sil 0000:01:0b.0: version 2.2
[ 63.952302] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 63.952312] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 19
[ 63.953010] scsi0 : sata_sil
[ 63.953330] scsi1 : sata_sil
[ 63.953468] ata1: SATA max UDMA/100 cmd 0xf884e080 ctl 0xf884e08a bmdma 0xf884e000 irq 19
[ 63.953474] ata2: SATA max UDMA/100 cmd 0xf884e0c0 ctl 0xf884e0ca bmdma 0xf884e008 irq 19
[ 63.969004] hda: ATAPI 40X CD-ROM CD-R/RW drive, 4096kB Cache, UDMA(33)
[ 63.969014] Uniform CD-ROM driver Revision: 3.20
[ 63.973061] hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 64.307552] end_request: I/O error, dev fd0, sector 0
[ 64.475415] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 64.484010] ata1.00: ATA-6: ST380013AS, 3.05, max UDMA/133
[ 64.484013] ata1.00: 156301488 sectors, multi 16: LBA48
[ 64.499981] ata1.00: configured for UDMA/100
[ 65.022913] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 65.031499] ata2.00: ATA-6: ST380013AS, 3.05, max UDMA/133
[ 65.031502] ata2.00: 156301488 sectors, multi 16: LBA48
[ 65.047470] ata2.00: configured for UDMA/100
[ 65.047601] scsi 0:0:0:0: Direct-Access ATA ST380013AS 3.05 PQ: 0 ANSI: 5
[ 65.048078] scsi 1:0:0:0: Direct-Access ATA ST380013AS 3.05 PQ: 0 ANSI: 5
[ 65.048778] ACPI: PCI Interrupt Link [AP3C] enabled at IRQ 20
[ 65.048785] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [AP3C] -> GSI 20 (level, high) -> IRQ 18
[ 65.048793] 3c59x: Donald Becker and others.
[ 65.048799] 0000:02:01.0: 3Com PCI 3c920 Tornado at f8850000.
[ 65.085226] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 65.085243] sd 0:0:0:0: [sda] Write Protect is off
[ 65.085246] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 65.085262] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 65.085340] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 65.085348] sd 0:0:0:0: [sda] Write Protect is off
[ 65.085351] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 65.085364] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 65.085370] sda: sda1 sda2 sda3
[ 65.108497] sd 0:0:0:0: [sda] Attached SCSI disk
[ 65.108679] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 65.108693] sd 1:0:0:0: [sdb] Write Protect is off
[ 65.108696] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 65.108711] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 65.108764] sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 65.108773] sd 1:0:0:0: [sdb] Write Protect is off
[ 65.108776] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 65.108789] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 65.108792] sdb: sdb1 sdb2
[ 65.128333] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 65.132980] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 65.133119] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 65.366594] end_request: I/O error, dev fd0, sector 0
[ 66.165026] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 66.192588] ISO 9660 Extensions: RRIP_1991A
[ 66.463854] Registering unionfs 1.4
[ 66.463859] unionfs: debugging is not enabled
[ 66.486291] loop: module loaded
[ 66.732182] squashfs: version 3.2-UBUNTU (2007/07/26) Phillip Lougher
[ 127.853177] Linux agpgart interface v0.102 (c) Dave Jones
[ 127.947335] agpgart: Detected NVIDIA nForce2 chipset
[ 127.952067] agpgart: AGP aperture is 64M @ 0xe0000000
[ 128.178926] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 128.178957] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5500
[ 128.727228] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 128.832533] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 129.701291] input: PC Speaker as /class/input/input3
[ 129.852514] ieee80211_crypt: registered algorithm 'NULL'
[ 129.854426] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 129.854431] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 129.944553] parport_pc 00:0c: reported by Plug and Play ACPI
[ 129.944617] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 130.071999] usb 3-2: reset high speed USB device using ehci_hcd and address 2
[ 130.417244] zd1211rw 3-2:1.0: firmware version 4605
[ 130.465199] zd1211rw 3-2:1.0: zd1211 chip 079b:004a v4330 high 00-60-b3 AL2230_RF pa0 g----
[ 130.467664] zd1211rw 3-2:1.0: eth2
[ 130.467685] usbcore: registered new interface driver zd1211rw
[ 130.831049] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[ 130.831056] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 16
[ 130.831081] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 131.151012] intel8x0_measure_ac97_clock: measured 52792 usecs
[ 131.151018] intel8x0: clocking to 48000
[ 132.544594] Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
[ 135.205679] No dock devices found.
[ 135.288142] input: Power Button (FF) as /class/input/input4
[ 135.293048] ACPI: Power Button (FF) [PWRF]
[ 135.334125] input: Power Button (CM) as /class/input/input5
[ 135.339016] ACPI: Power Button (CM) [PWRB]
[ 141.286105] eth0: no link during initialization.
[ 141.463322] lp0: using parport0 (interrupt-driven).
[ 141.485726] eth1: setting half-duplex.
[ 141.515850] ppdev: user-space parallel port driver
[ 143.375790] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 143.375796] apm: overridden by ACPI.
[ 143.720468] Failure registering capabilities with primary security module.
[ 144.820405] Bluetooth: Core ver 2.11
[ 144.820554] NET: Registered protocol family 31
[ 144.820557] Bluetooth: HCI device and connection manager initialized
[ 144.820560] Bluetooth: HCI socket layer initialized
[ 144.932072] Bluetooth: L2CAP ver 2.8
[ 144.932078] Bluetooth: L2CAP socket layer initialized
[ 145.056338] Bluetooth: RFCOMM socket layer initialized
[ 145.056445] Bluetooth: RFCOMM TTY layer initialized
[ 145.056447] Bluetooth: RFCOMM ver 1.8
[ 150.888314] [drm] Initialized drm 1.1.0 20060810
[ 150.922486] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 150.922499] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 20
[ 150.925519] [drm] Initialized radeon 1.27.0 20060524 on minor 0
[ 153.109928] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 153.110060] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 153.110211] agpgart: Putting AGP V3 device at 0000:03:00.0 into 8x mode
[ 153.368088] [drm] Setting GART location based on new memory map
[ 153.368102] [drm] Loading R300 Microcode
[ 153.368152] [drm] writeback test succeeded in 1 usecs
[ 377.008381] usb 3-6: new high speed USB device using ehci_hcd and address 4
[ 377.153465] usb 3-6: configuration #1 chosen from 1 choice
[ 377.472989] usbcore: registered new interface driver libusual
[ 378.496627] Initializing USB Mass Storage driver...
[ 378.497327] scsi2 : SCSI emulation for USB Mass Storage devices
[ 378.498032] usb-storage: device found at 4
[ 378.498037] usb-storage: waiting for device to settle before scanning
[ 378.498221] usbcore: registered new interface driver usb-storage
[ 378.498308] USB Mass Storage support registered.
[ 383.490644] usb-storage: device scan complete
[ 383.491133] scsi 2:0:0:0: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 0 CCS
[ 383.491611] scsi 2:0:0:1: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 0 CCS
[ 384.683766] sd 2:0:0:0: [sdc] 498688 512-byte hardware sectors (255 MB)
[ 384.684385] sd 2:0:0:0: [sdc] Write Protect is off
[ 384.684389] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 384.684392] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 384.686508] sd 2:0:0:0: [sdc] 498688 512-byte hardware sectors (255 MB)
[ 384.687133] sd 2:0:0:0: [sdc] Write Protect is off
[ 384.687136] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 384.687138] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 384.687143] sdc: sdc1
[ 384.688639] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 384.688701] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 384.695555] sd 2:0:0:1: [sdd] 2880 512-byte hardware sectors (1 MB)
[ 384.697458] sd 2:0:0:1: [sdd] Write Protect is off
[ 384.697466] sd 2:0:0:1: [sdd] Mode Sense: 23 94 00 00
[ 384.697469] sd 2:0:0:1: [sdd] Assuming drive cache: write through
[ 384.705424] sd 2:0:0:1: [sdd] 2880 512-byte hardware sectors (1 MB)
[ 384.707098] sd 2:0:0:1: [sdd] Write Protect is off
[ 384.707102] sd 2:0:0:1: [sdd] Mode Sense: 23 94 00 00
[ 384.707105] sd 2:0:0:1: [sdd] Assuming drive cache: write through
[ 384.707110] sdd: unknown partition table
[ 384.710512] sd 2:0:0:1: [sdd] Attached SCSI removable disk
[ 384.710566] sd 2:0:0:1: Attached scsi generic sg3 type 0
ubuntu@ubuntu:~$
Hors ligne
#5 Le 03/02/2008, à 13:21
- patko
Re : Problème au boot
Salut, est-il possible de poster le résultat de sudo fdisk -l?
sinon est-ce que fsck -y donne quelque chose?
#6 Le 03/02/2008, à 13:34
- seb_68
Re : Problème au boot
Voici:
fdisk -l:
ubuntu@ubuntu:~$ fdisk -l
Disque /dev/sdc: 255 Mo, 255328256 octets
16 heads, 32 sectors/track, 974 cylinders
Units = cylindres of 512 * 512 = 262144 bytes
Disk identifier: 0x6ba8b0c5
Périphérique Amorce Début Fin Blocs Id Système
/dev/sdc1 * 1 974 249328 6 FAT16
Disque /dev/sdd: 1 Mo, 1474560 octets
1 heads, 3 sectors/track, 960 cylinders
Units = cylindres of 3 * 512 = 1536 bytes
Disk identifier: 0x69737369
Cela ne ressemble pas à une table de partition.
Probablement vous avez sélectionné le mauvais périphérique.
Périphérique Amorce Début Fin Blocs Id Système
/dev/sdd1 ? 623257122 679486963 84344761 69 Inconnu
Partition 1 a des débuts différents physique/logique (non Linux?):
phys=(68, 13, 10) logique=(623257121, 0, 3)
Partition 1 a des fins différentes physique/logique:
phys=(288, 115, 43) logique=(679486962, 0, 1)
La partition 1 ne se termine pas sur une frontière de cylindre.
/dev/sdd2 ? 567173161 1190466982 934940732+ 73 Inconnu
Partition 2 a des débuts différents physique/logique (non Linux?):
phys=(371, 114, 37) logique=(567173160, 0, 2)
Partition 2 a des fins différentes physique/logique:
phys=(366, 32, 33) logique=(1190466981, 0, 3)
La partition 2 ne se termine pas sur une frontière de cylindre.
/dev/sdd3 ? 858 858 0 74 Inconnu
Partition 3 a des débuts différents physique/logique (non Linux?):
phys=(371, 114, 37) logique=(857, 0, 3)
Partition 3 a des fins différentes physique/logique:
phys=(372, 97, 50) logique=(857, 0, 2)
La partition 3 ne se termine pas sur une frontière de cylindre.
/dev/sdd4 1 1145037824 1717556736 0 Vide
Partition 4 a des débuts différents physique/logique (non Linux?):
phys=(0, 0, 0) logique=(0, 0, 1)
Partition 4 a des fins différentes physique/logique:
phys=(0, 0, 0) logique=(1145037823, 0, 3)
La partition 4 ne se termine pas sur une frontière de cylindre.
Les entrées de la table de partitions ne sont pas dans l'ordre du disque
ubuntu@ubuntu:~$
sudo fsck -y
ubuntu@ubuntu:~$ sudo fsck -y
fsck 1.40.2 (12-Jul-2007)
Hors ligne
#7 Le 03/02/2008, à 13:51
- seb_68
Re : Problème au boot
J'essaie de recuperer mes fichiers via le livecd de Knoppix:
Voici le resultat lorsque je clique sur l'icone de sda3 (entre autre):
Mount: wrong fs type, bad option, bad superblock on /dev/sda3/
Missing codepage or other error....
C'est grave?
Hors ligne
#8 Le 03/02/2008, à 14:21
- patko
Re : Problème au boot
J'essaie de recuperer mes fichiers via le livecd de Knoppix:
Voici le resultat lorsque je clique sur l'icone de sda3 (entre autre):Mount: wrong fs type, bad option, bad superblock on /dev/sda3/
Missing codepage or other error....C'est grave?
je pense que fsck a besoin de connaître le type de système de fichier pour pouvoir réparer avec l'option -t suivit du type de fichier, il faudrait pouvoir déterminer ce que c'était... si l'installation était une gutsy ça devait être du ext3
#9 Le 03/02/2008, à 14:30
- patko
Re : Problème au boot
Voici:
fdisk -l:
merci, c'est bizarre il n'y a ni sda, ni sdb, indiqués au premier post, quelque chose a changé depuis?
sudo fsck -y
cette commande répare les disque sans poster d'erreur et même si la table des partitions semble bonne, selon la doc (man fsck), ça n'a rien réparé?
Pages : 1