#26 Le 08/07/2017, à 20:29
- chapichapoto
Re : voyant DD toujours allumé RESOLU
merci
Hors ligne
#27 Le 08/07/2017, à 22:09
- Compte anonymisé
Re : voyant DD toujours allumé RESOLU
jojo81 a écrit :
Jacksnice06 a écrit :est je maintient 52 c'est pas énorme suivant la région ici j'ai déjà + de trente en température ambiante avec la chaleur dans la maison !
à ta place, je me méfierais de ce discours-là. Autant un proce est conçu pour des écarts de température élevés, autant un disque mécanique sera plus sensible.
Toobuntu a écrit :Tu supprime le passage d'air forcé qui doit venir refroidir le disque.
+1 , mais ce qui me dérange, c'est en #23 , si chapichapoto a lancé sa mesure dès la reprise d'activité du disque, c'est que le disque étouffe.
@jojo81 pour mon cas personnel sur la tour avec un bon gros châssis en aluminium est 3 hd dans le boîtier par c'est forte chaleur dans la région actuellement 30,7 dans la pièce avec les fenêtres ouverte est pas un pétte d'Air est 36 dans le boîtier.aire Amb... dans le boîtier.
truc qui tourne chui a une valeur moyenne de 47 pour ca pour ma part que je ne trouves pas ca ennorme .apres je ne connais pas la région n'y la chaleur qu'il a en c moment chez lui ce qui contribue à la chose n'y encore moi son matériel ! Une maison n'est pas un lan center !
#28 Le 09/07/2017, à 06:01
- moko138
Re : voyant DD toujours allumé RESOLU
chapichapoto,
montre-nous le retour complet de
sudo hdparm -B /dev/sda ; echo ; sudo smartctl -s on -a /dev/sdapuis, bien séparé, celui de :
sudo hdparm -B /dev/sdb ; echo ; sudo smartctl -s on -a /dev/sdbMerci !
Dernière modification par moko138 (Le 09/07/2017, à 06:20)
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#29 Le 09/07/2017, à 06:19
- moko138
Re : voyant DD toujours allumé RESOLU
Jacksnice06 a écrit :
Un peu de lecture bonne soirée https://doc.ubuntu-fr.org/lm-sensors#ge … surchauffe
Ton lien renvoie sur :
Le ventilateur du processeur ne fonctionne plus après quelques minutes, l'ordinateur portable surchauffe et s'arrête. Pour éviter cela, (...)
Jacksnice06,
chapichapoto nous parle d'une tour et d'activité et de température des disques.
chapichapoto ne nous a pas parlé ni d'arrêt spontané ni de processeur ni de portable.
Dernière modification par moko138 (Le 09/07/2017, à 06:24)
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#30 Le 09/07/2017, à 10:16
- Compte anonymisé
Re : voyant DD toujours allumé RESOLU
Ubuntu peut suivre la température de votre processeur ou d'autres composants de votre ordinateur, la vitesse des ventilateurs, et d'autres données systèmes, Chui d'accord moko mais ci tu remonte un peu il ne fait pas que te renvoyer les donné du proc !
#31 Le 09/07/2017, à 13:21
- chapichapoto
Re : voyant DD toujours allumé RESOLU
Bonjour à tous, voici ce que vous m'avez demandé:
/dev/sda:
APM_level = not supported
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.8.15-040815-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3500630A
Serial Number: 9QG468MB
Firmware Version: 3.AAF
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sun Jul 9 13:16:23 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 163) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 088 006 Pre-fail Always - 208007978
3 Spin_Up_Time 0x0003 096 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 094 094 020 Old_age Always - 6202
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 039 036 030 Pre-fail Always - 255864754829346
9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 23534
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 095 095 020 Old_age Always - 5585
187 Reported_Uncorrect 0x0032 079 079 000 Old_age Always - 21
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 049 042 045 Old_age Always In_the_past 51 (Min/Max 26/51)
194 Temperature_Celsius 0x0022 051 058 000 Old_age Always - 51 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 061 052 000 Old_age Always - 80537382
197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 4294967295
198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 4294967295
199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always - 127
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 160 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 160 occurred at disk power-on lifetime: 20797 hours (866 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 28 ae b4 e1 00 05:35:55.120 READ DMA
c8 00 a0 20 af 91 e1 00 05:35:54.799 READ DMA
c8 00 88 d8 30 97 e1 00 05:35:54.799 READ DMA
35 00 00 b0 1c 30 e0 00 05:35:54.775 WRITE DMA EXT
35 00 58 58 18 30 e0 00 05:35:54.774 WRITE DMA EXT
Error 159 occurred at disk power-on lifetime: 20797 hours (866 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 20 90 70 d6 e1 00 05:34:09.765 READ DMA
c8 00 08 a0 40 41 e0 00 05:34:09.753 READ DMA
c8 00 90 d0 c9 49 e0 00 05:34:09.752 READ DMA
c8 00 08 70 d2 49 e0 00 05:34:09.752 READ DMA
c8 00 08 48 21 41 e0 00 05:34:09.739 READ DMA
Error 158 occurred at disk power-on lifetime: 13592 hours (566 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ef 7b 60 e0 00 00:08:44.475 READ DMA EXT
29 00 48 4f 73 60 e0 00 00:08:44.439 READ MULTIPLE EXT
29 00 f8 b7 6e 60 e0 00 00:08:44.408 READ MULTIPLE EXT
29 00 00 b7 6d 60 e0 00 00:08:44.369 READ MULTIPLE EXT
29 00 08 17 6b 60 e0 00 00:08:44.364 READ MULTIPLE EXT
Error 157 occurred at disk power-on lifetime: 13592 hours (566 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 00 00 00 e0 00 00:08:27.513 READ DMA EXT
29 03 08 3f 00 60 e0 00 00:08:27.065 READ MULTIPLE EXT
25 03 01 00 00 00 e0 00 00:08:27.065 READ DMA EXT
ef 03 40 01 10 00 a0 02 00:08:27.065 SET FEATURES [Set transfer mode]
ef 03 0c 01 10 00 a0 02 00:08:27.064 SET FEATURES [Set transfer mode]
Error 156 occurred at disk power-on lifetime: 13592 hours (566 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 00 00 00 e0 00 00:08:27.513 READ DMA EXT
ef 03 40 01 10 00 a0 02 00:08:27.065 SET FEATURES [Set transfer mode]
ef 03 0c 01 10 00 a0 02 00:08:27.065 SET FEATURES [Set transfer mode]
c6 00 10 01 00 00 a0 02 00:08:27.065 SET MULTIPLE MODE
91 00 3f 01 00 00 af 02 00:08:27.064 INITIALIZE DEVICE PARAMETERS [OBS-6]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 21095 -
# 2 Short offline Completed without error 00% 19842 -
# 3 Short offline Completed without error 00% 19839 -
# 4 Short offline Completed without error 00% 19839 -
# 5 Short offline Completed without error 00% 13874 -
# 6 Short offline Completed without error 00% 4482 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay./dev/sdb:
APM_level = not supported
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.8.15-040815-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.8
Device Model: ST3400832A
Serial Number: 5NF0N2VD
Firmware Version: 3.03
User Capacity: 400 088 457 216 bytes [400 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sun Jul 9 13:18:50 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 134) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 046 044 006 Pre-fail Always - 197615765
3 Spin_Up_Time 0x0003 097 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1860
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 600429750
9 Power_On_Hours 0x0032 070 070 000 Old_age Always - 26705
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2104
194 Temperature_Celsius 0x0022 050 058 000 Old_age Always - 50 (0 14 0 0 0)
195 Hardware_ECC_Recovered 0x001a 046 044 000 Old_age Always - 197615765
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 19944 hours (831 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 3a 00 5e e0 Error: UNC at LBA = 0x005e003a = 6160442
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 37 00 5e e0 00 00:00:31.102 READ DMA EXT
25 d8 08 37 00 5e e0 00 00:00:31.102 READ DMA EXT
25 d8 08 2f 00 5e e0 00 00:00:31.102 READ DMA EXT
25 d8 08 df 1c 20 e0 00 00:00:31.102 READ DMA EXT
25 d8 08 3f 00 60 e0 00 00:00:31.101 READ DMA EXT
Error 3 occurred at disk power-on lifetime: 19944 hours (831 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 3a 00 5e e0 Error: UNC at LBA = 0x005e003a = 6160442
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 37 00 5e e0 00 00:00:31.102 READ DMA EXT
25 d8 08 2f 00 5e e0 00 00:00:31.102 READ DMA EXT
25 d8 08 df 1c 20 e0 00 00:00:31.102 READ DMA EXT
25 d8 08 3f 00 60 e0 00 00:00:31.102 READ DMA EXT
25 d8 08 3f 00 00 e0 00 00:00:31.101 READ DMA EXT
Error 2 occurred at disk power-on lifetime: 19851 hours (827 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 46 08 28 e0 Error: UNC at LBA = 0x00280846 = 2623558
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 3f 08 28 e0 00 00:00:49.616 READ DMA EXT
ea 00 00 00 00 00 a0 00 00:00:48.589 FLUSH CACHE EXT
35 00 08 47 00 5e e0 00 00:00:48.589 WRITE DMA EXT
35 00 04 f7 9c 30 e0 00 00:00:48.589 WRITE DMA EXT
35 00 18 77 4f 60 e0 00 00:00:48.589 WRITE DMA EXT
Error 1 occurred at disk power-on lifetime: 19850 hours (827 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 45 08 28 e0 Error: UNC at LBA = 0x00280845 = 2623557
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 3f 08 28 e0 00 01:53:00.563 READ DMA EXT
ea 00 00 00 00 00 a0 00 01:53:00.563 FLUSH CACHE EXT
35 00 08 3f 00 5e e0 00 01:53:00.563 WRITE DMA EXT
35 00 04 f7 9c 30 e0 00 01:53:00.562 WRITE DMA EXT
35 00 08 3f 2b 60 e0 00 01:53:00.562 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 23024 -
# 2 Short offline Completed without error 00% 23021 -
# 3 Short offline Completed without error 00% 23021 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Hors ligne
#32 Le 09/07/2017, à 15:39
- moko138
Re : voyant DD toujours allumé RESOLU
Aucun de tes deux Seagate Barracuda ne supporte la gestion de l'APM, donc nous ne pouvons pas jouer là-dessus pour diminuer la température.
- -
sdb (400 Go)
Il peut encore servir,
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2104
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
(...)
Error 4 occurred at disk power-on lifetime: 19944 hoursmais avec 26.705 heures à 7.200 t/min, il a dépassé les
11,5 milliards de tours, il vaut mieux ne pas lui faire confiance pour le stockage de tes données.
- -
Pour sda (500 Go) :
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 23534
12 Power_Cycle_Count 0x0032 095 095 020 Old_age Always - 5585
187 Reported_Uncorrect 0x0032 079 079 000 Old_age Always - 21
190 Airflow_Temperature_Cel 0x0022 049 042 045 Old_age Always In_the_past 51 (Min/Max 26/51)
194 Temperature_Celsius 0x0022 051 058 000 Old_age Always - 51 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 061 052 000 Old_age Always - 80537382
197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 4294967295
198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 4294967295
199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always - 127
(...)
Error 160 occurred at disk power-on lifetime: 20797 hours1) Ses difficultés de lecture-écriture expliquent ton "voyant DD toujours allumé".
2) Même si les nombres donnés en 195, 197 et 198 sont aberrants,
il est prêt à devenir un presse-papiers de rêve.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#33 Le 09/07/2017, à 16:37
- Compte anonymisé
Re : voyant DD toujours allumé RESOLU
Tiens de un on n'est passer à deux hdd j'ai lu les retours de commande je croyais que c'était le 1 avril
On veut bien aidé tu chapicha... mais il faut un minimum d'informations sinon les aidant perde du temps est ne savent plus trop ou partir .... il faut un minimum d'informations sur la machine je pense qu'on ne le dit pas assez car après on va à l'aveugle !