#126 Le 28/08/2017, à 23:48
- abelthorne
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Après ça, pas de changement du côté de Simple Scan ?
Hors ligne
#127 Le 28/08/2017, à 23:49
- julien_sen
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Non.
Hors ligne
#128 Le 28/08/2017, à 23:52
- abelthorne
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Bon, alors essaie de connecter ton scanner à ton réseau wi-fi et fais un essai avec Simple Scan pour vérifier s'il le voit dans les préférences (normalement, il doit voir deux scanners différents, un pour chaque type de connexion). C'est fort probable que ce ne soit pas le cas, je crois qu'il y a une manip à faire pour déclarer un scanner réseau mais fais quand même un essai le temps que je retrouve ça.
EDIT : il faudra commencer par voir s'il est détecté en scanner réseau avec :
brsaneconfig3 -dDernière modification par abelthorne (Le 28/08/2017, à 23:54)
Hors ligne
#129 Le 29/08/2017, à 00:00
- julien_sen
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
J'ai plusieurs IP... Je prends IPv4 ou IPv6 ?
brsaneconfig3 -dcat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda2 during installation
UUID=a4d11e7c-40c1-473b-af79-4923773df2a8 / ext4 errors=remount-ro 0 1
# /boot/efi was on /dev/sda1 during installation
#UUID=81CE-0F89 /boot/efi vfat umask=0077 0 1
/swapfile none swap sw 0 0
UUID=81CE-0F89 /boot/efi vfat defaults 0 1
-----------------------------
sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
could not open USB device 0x1d6b/0x0003 at 002:001: Access denied (insufficient permissions)
could not open USB device 0x04f2/0xb469 at 001:003: Access denied (insufficient permissions)
found USB scanner (vendor=0x04f9, product=0x01e8) at libusb:001:009
could not open USB device 0x04ca/0x300b at 001:005: Access denied (insufficient permissions)
could not open USB device 0x05e3/0x0608 at 001:002: Access denied (insufficient permissions)
could not open USB device 0x046d/0xc077 at 001:006: Access denied (insufficient permissions)
could not open USB device 0x1d6b/0x0002 at 001:001: Access denied (insufficient permissions)
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
-----------------------------
ls -R -all /proc/bus/usb
ls: impossible d'accéder à '/proc/bus/usb': Aucun fichier ou dossier de ce type
-----------------------------
cat /proc/bus/usb/devices
cat: /proc/bus/usb/devices: Aucun fichier ou dossier de ce type
-----------------------------
scanimage -L
[sanei_debug] Setting debug level of dll to 128.
[dll] sane_init: SANE dll backend version 1.0.13 from sane-backends 1.0.25git
[dll] sane_init/read_dlld: attempting to open directory `./dll.d'
[dll] sane_init/read_dlld: attempting to open directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: using config directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/hplip
[dll] sane_init/read_config: reading dll.d/hplip
[dll] add_backend: adding backend `hpaio'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/libsane-extras
[dll] sane_init/read_config: reading dll.d/libsane-extras
[dll] add_backend: adding backend `ls5000'
[dll] sane_init/read_dlld: done.
[dll] sane_init/read_config: reading dll.conf
[dll] add_backend: adding backend `net'
[dll] add_backend: adding backend `abaton'
[dll] add_backend: adding backend `agfafocus'
[dll] add_backend: adding backend `apple'
[dll] add_backend: adding backend `avision'
[dll] add_backend: adding backend `artec'
[dll] add_backend: adding backend `artec_eplus48u'
[dll] add_backend: adding backend `as6e'
[dll] add_backend: adding backend `bh'
[dll] add_backend: adding backend `canon'
[dll] add_backend: adding backend `canon630u'
[dll] add_backend: adding backend `canon_dr'
[dll] add_backend: adding backend `cardscan'
[dll] add_backend: adding backend `coolscan'
[dll] add_backend: adding backend `coolscan3'
[dll] add_backend: adding backend `dell1600n_net'
[dll] add_backend: adding backend `dmc'
[dll] add_backend: adding backend `epjitsu'
[dll] add_backend: adding backend `epson2'
[dll] add_backend: adding backend `epsonds'
[dll] add_backend: adding backend `fujitsu'
[dll] add_backend: adding backend `genesys'
[dll] add_backend: adding backend `gt68xx'
[dll] add_backend: adding backend `hp'
[dll] add_backend: adding backend `hp3900'
[dll] add_backend: adding backend `hpsj5s'
[dll] add_backend: adding backend `hp3500'
[dll] add_backend: adding backend `hp4200'
[dll] add_backend: adding backend `hp5400'
[dll] add_backend: adding backend `hp5590'
[dll] add_backend: adding backend `hpljm1005'
[dll] add_backend: adding backend `hs2p'
[dll] add_backend: adding backend `ibm'
[dll] add_backend: adding backend `kodak'
[dll] add_backend: adding backend `kodakaio'
[dll] add_backend: adding backend `kvs1025'
[dll] add_backend: adding backend `kvs20xx'
[dll] add_backend: adding backend `leo'
[dll] add_backend: adding backend `lexmark'
[dll] add_backend: adding backend `ma1509'
[dll] add_backend: adding backend `magicolor'
[dll] add_backend: adding backend `matsushita'
[dll] add_backend: adding backend `microtek'
[dll] add_backend: adding backend `microtek2'
[dll] add_backend: adding backend `mustek'
[dll] add_backend: adding backend `mustek_usb'
[dll] add_backend: adding backend `mustek_usb2'
[dll] add_backend: adding backend `nec'
[dll] add_backend: adding backend `niash'
[dll] add_backend: adding backend `pie'
[dll] add_backend: adding backend `pixma'
[dll] add_backend: adding backend `plustek'
[dll] add_backend: adding backend `qcam'
[dll] add_backend: adding backend `ricoh'
[dll] add_backend: adding backend `rts8891'
[dll] add_backend: adding backend `s9036'
[dll] add_backend: adding backend `sceptre'
[dll] add_backend: adding backend `sharp'
[dll] add_backend: adding backend `sm3600'
[dll] add_backend: adding backend `sm3840'
[dll] add_backend: adding backend `snapscan'
[dll] add_backend: adding backend `sp15c'
[dll] add_backend: adding backend `tamarack'
[dll] add_backend: adding backend `teco1'
[dll] add_backend: adding backend `teco2'
[dll] add_backend: adding backend `teco3'
[dll] add_backend: adding backend `u12'
[dll] add_backend: adding backend `umax'
[dll] add_backend: adding backend `umax1220u'
[dll] add_backend: adding backend `v4l'
[dll] add_backend: adding backend `xerox_mfp'
[dll] add_backend: adding backend `brother3'
[dll] sane_get_devices
[dll] load: searching backend `brother3' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-brother3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-brother3.so.1'
[dll] init: initializing backend `brother3'
[dll] init: backend `brother3' is version 1.0.1
[dll] load: searching backend `xerox_mfp' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] init: initializing backend `xerox_mfp'
[dll] init: backend `xerox_mfp' is version 1.0.13
[dll] load: searching backend `v4l' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1' (No such file or directory)
[dll] load: trying to load `/usr/lib/sane/libsane-v4l.so.1'
[dll] load: couldn't open `/usr/lib/sane/libsane-v4l.so.1' (No such file or directory)
[dll] load: couldn't find backend `v4l' (No such file or directory)
[dll] load: searching backend `umax1220u' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] init: initializing backend `umax1220u'
[dll] init: backend `umax1220u' is version 1.0.2
[dll] load: searching backend `umax' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] init: initializing backend `umax'
[dll] init: backend `umax' is version 1.0.45
[dll] load: searching backend `u12' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] init: initializing backend `u12'
[dll] init: backend `u12' is version 1.0.0
[dll] load: searching backend `teco3' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] init: initializing backend `teco3'
[dll] init: backend `teco3' is version 1.0.1
[dll] load: searching backend `teco2' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] init: initializing backend `teco2'
[dll] init: backend `teco2' is version 1.0.10
[dll] load: searching backend `teco1' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] init: initializing backend `teco1'
[dll] init: backend `teco1' is version 1.0.10
[dll] load: searching backend `tamarack' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] init: initializing backend `tamarack'
[dll] init: backend `tamarack' is version 1.0.0
[dll] load: searching backend `sp15c' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] init: initializing backend `sp15c'
[dll] init: backend `sp15c' is version 1.0.0
[dll] load: searching backend `snapscan' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] init: initializing backend `snapscan'
[dll] init: backend `snapscan' is version 1.4.53
[dll] load: searching backend `sm3840' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] init: initializing backend `sm3840'
[dll] init: backend `sm3840' is version 1.0.0
[dll] load: searching backend `sm3600' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] init: initializing backend `sm3600'
[dll] init: backend `sm3600' is version 1.0.6
[dll] load: searching backend `sharp' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] init: initializing backend `sharp'
[dll] init: backend `sharp' is version 1.0.0
[dll] load: searching backend `sceptre' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] init: initializing backend `sceptre'
[dll] init: backend `sceptre' is version 1.0.10
[dll] load: searching backend `s9036' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] init: initializing backend `s9036'
[dll] init: backend `s9036' is version 1.0.0
[dll] load: searching backend `rts8891' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] init: initializing backend `rts8891'
[dll] init: backend `rts8891' is version 1.0.2401
[dll] load: searching backend `ricoh' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] init: initializing backend `ricoh'
[dll] init: backend `ricoh' is version 1.0.0
[dll] load: searching backend `qcam' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] init: initializing backend `qcam'
[dll] init: backend `qcam' is version 1.0.0
[dll] load: searching backend `plustek' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] init: initializing backend `plustek'
[dll] init: backend `plustek' is version 1.0.0
[dll] load: searching backend `pixma' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] init: initializing backend `pixma'
[dll] init: backend `pixma' is version 1.0.17
[dll] load: searching backend `pie' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] init: initializing backend `pie'
[dll] init: backend `pie' is version 1.0.9
[dll] load: searching backend `niash' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] init: initializing backend `niash'
[dll] init: backend `niash' is version 1.0.1
[dll] load: searching backend `nec' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] init: initializing backend `nec'
[dll] init: backend `nec' is version 1.0.0
[dll] load: searching backend `mustek_usb2' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] init: initializing backend `mustek_usb2'
[dll] init: backend `mustek_usb2' is version 1.0.10
[dll] load: searching backend `mustek_usb' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] init: initializing backend `mustek_usb'
[dll] init: backend `mustek_usb' is version 1.0.18
[dll] load: searching backend `mustek' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[dll] init: backend `mustek' is version 1.0.138
[dll] load: searching backend `microtek2' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[dll] init: backend `microtek2' is version 1.0.0
[dll] load: searching backend `microtek' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[dll] init: backend `microtek' is version 1.0.0
[dll] load: searching backend `matsushita' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] init: initializing backend `matsushita'
[dll] init: backend `matsushita' is version 1.0.7
[dll] load: searching backend `magicolor' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] init: initializing backend `magicolor'
[dll] init: backend `magicolor' is version 1.0.1
[dll] load: searching backend `ma1509' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] init: initializing backend `ma1509'
[dll] init: backend `ma1509' is version 1.0.3
[dll] load: searching backend `lexmark' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] init: initializing backend `lexmark'
[dll] init: backend `lexmark' is version 1.0.32
[dll] load: searching backend `leo' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] init: initializing backend `leo'
[dll] init: backend `leo' is version 1.0.11
[dll] load: searching backend `kvs20xx' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] init: initializing backend `kvs20xx'
[dll] init: backend `kvs20xx' is version 1.0.2
[dll] load: searching backend `kvs1025' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] init: initializing backend `kvs1025'
[dll] init: backend `kvs1025' is version 1.0.5
[dll] load: searching backend `kodakaio' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] init: initializing backend `kodakaio'
[dll] init: backend `kodakaio' is version 1.0.2
[dll] load: searching backend `kodak' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] init: initializing backend `kodak'
[dll] init: backend `kodak' is version 1.0.7
[dll] load: searching backend `ibm' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] init: initializing backend `ibm'
[dll] init: backend `ibm' is version 1.0.0
[dll] load: searching backend `hs2p' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] init: initializing backend `hs2p'
[dll] init: backend `hs2p' is version 1.0.0
[dll] load: searching backend `hpljm1005' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] init: initializing backend `hpljm1005'
[dll] init: backend `hpljm1005' is version 1.0.1
[dll] load: searching backend `hp5590' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] init: initializing backend `hp5590'
[dll] init: backend `hp5590' is version 1.0.7
[dll] load: searching backend `hp5400' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] init: initializing backend `hp5400'
[dll] init: backend `hp5400' is version 1.0.3
[dll] load: searching backend `hp4200' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] init: initializing backend `hp4200'
[dll] init: backend `hp4200' is version 1.0.0
[dll] load: searching backend `hp3500' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] init: initializing backend `hp3500'
[dll] init: backend `hp3500' is version 1.0.0
[dll] load: searching backend `hpsj5s' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] init: initializing backend `hpsj5s'
[dll] init: backend `hpsj5s' is version 1.0.3
[dll] load: searching backend `hp3900' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] init: initializing backend `hp3900'
[dll] init: backend `hp3900' is version 1.0.0
[dll] load: searching backend `hp' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] init: initializing backend `hp'
[dll] init: backend `hp' is version 1.0.8
[dll] load: searching backend `gt68xx' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] init: initializing backend `gt68xx'
[dll] init: backend `gt68xx' is version 1.0.84
[dll] load: searching backend `genesys' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] init: initializing backend `genesys'
[dll] init: backend `genesys' is version 1.0.2506
[dll] load: searching backend `fujitsu' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] init: initializing backend `fujitsu'
[dll] init: backend `fujitsu' is version 1.0.126
[dll] load: searching backend `epsonds' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] init: initializing backend `epsonds'
[dll] init: backend `epsonds' is version 1.0.35
[dll] load: searching backend `epson2' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] init: initializing backend `epson2'
[dll] init: backend `epson2' is version 1.0.124
[dll] load: searching backend `epjitsu' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] init: initializing backend `epjitsu'
[dll] init: backend `epjitsu' is version 1.0.28
[dll] load: searching backend `dmc' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] init: initializing backend `dmc'
[dll] init: backend `dmc' is version 1.0.0
[dll] load: searching backend `dell1600n_net' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] init: initializing backend `dell1600n_net'
[dll] init: backend `dell1600n_net' is version 1.0.0
[dll] load: searching backend `coolscan3' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] init: initializing backend `coolscan3'
[dll] init: backend `coolscan3' is version 1.0.0
[dll] load: searching backend `coolscan' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] init: initializing backend `coolscan'
[dll] init: backend `coolscan' is version 1.0.0
[dll] load: searching backend `cardscan' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] init: initializing backend `cardscan'
[dll] init: backend `cardscan' is version 1.0.2
[dll] load: searching backend `canon_dr' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] init: initializing backend `canon_dr'
[dll] init: backend `canon_dr' is version 1.0.49
[dll] load: searching backend `canon630u' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] init: initializing backend `canon630u'
[dll] init: backend `canon630u' is version 1.0.1
[dll] load: searching backend `canon' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] init: initializing backend `canon'
[dll] init: backend `canon' is version 1.0.0
[dll] load: searching backend `bh' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] init: initializing backend `bh'
[dll] init: backend `bh' is version 1.0.4
[dll] load: searching backend `as6e' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] init: initializing backend `as6e'
[dll] load: searching backend `artec_eplus48u' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] init: initializing backend `artec_eplus48u'
[dll] init: backend `artec_eplus48u' is version 1.0.0
[dll] load: searching backend `artec' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] init: initializing backend `artec'
[dll] init: backend `artec' is version 1.0.0
[dll] load: searching backend `avision' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] init: initializing backend `avision'
[dll] init: backend `avision' is version 1.0.297
[dll] load: searching backend `apple' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] init: initializing backend `apple'
[dll] init: backend `apple' is version 1.0.0
[dll] load: searching backend `agfafocus' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] init: initializing backend `agfafocus'
[dll] init: backend `agfafocus' is version 1.0.0
[dll] load: searching backend `abaton' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] init: initializing backend `abaton'
[dll] init: backend `abaton' is version 1.0.0
[dll] load: searching backend `net' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] init: initializing backend `net'
[dll] init: backend `net' is version 1.0.25
[dll] load: searching backend `ls5000' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] init: initializing backend `ls5000'
[dll] init: backend `ls5000' is version 1.0.0
[dll] load: searching backend `hpaio' in `/usr/lib/x86_64-linux-gnu/sane:/usr/lib/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] init: initializing backend `hpaio'
[dll] init: backend `hpaio' is version 1.0.0
[dll] sane_get_devices: found 1 devices
device `brother3:bus2;dev1' is a Brother DCP-7045N USB scanner
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `brother3's exit function
[dll] sane_exit: calling backend `xerox_mfp's exit function
[dll] sane_exit: calling backend `umax1220u's exit function
[dll] sane_exit: calling backend `umax's exit function
[dll] sane_exit: calling backend `u12's exit function
[dll] sane_exit: calling backend `teco3's exit function
[dll] sane_exit: calling backend `teco2's exit function
[dll] sane_exit: calling backend `teco1's exit function
[dll] sane_exit: calling backend `tamarack's exit function
[dll] sane_exit: calling backend `sp15c's exit function
[dll] sane_exit: calling backend `snapscan's exit function
[dll] sane_exit: calling backend `sm3840's exit function
[dll] sane_exit: calling backend `sm3600's exit function
[dll] sane_exit: calling backend `sharp's exit function
[dll] sane_exit: calling backend `sceptre's exit function
[dll] sane_exit: calling backend `s9036's exit function
[dll] sane_exit: calling backend `rts8891's exit function
[dll] sane_exit: calling backend `ricoh's exit function
[dll] sane_exit: calling backend `qcam's exit function
[dll] sane_exit: calling backend `plustek's exit function
[dll] sane_exit: calling backend `pixma's exit function
[dll] sane_exit: calling backend `pie's exit function
[dll] sane_exit: calling backend `niash's exit function
[dll] sane_exit: calling backend `nec's exit function
[dll] sane_exit: calling backend `mustek_usb2's exit function
[dll] sane_exit: calling backend `mustek_usb's exit function
[dll] sane_exit: calling backend `mustek's exit function
[dll] sane_exit: calling backend `microtek2's exit function
[dll] sane_exit: calling backend `microtek's exit function
[dll] sane_exit: calling backend `matsushita's exit function
[dll] sane_exit: calling backend `magicolor's exit function
[dll] sane_exit: calling backend `ma1509's exit function
[dll] sane_exit: calling backend `lexmark's exit function
[dll] sane_exit: calling backend `leo's exit function
[dll] sane_exit: calling backend `kvs20xx's exit function
[dll] sane_exit: calling backend `kvs1025's exit function
[dll] sane_exit: calling backend `kodakaio's exit function
[dll] sane_exit: calling backend `kodak's exit function
[dll] sane_exit: calling backend `ibm's exit function
[dll] sane_exit: calling backend `hs2p's exit function
[dll] sane_exit: calling backend `hpljm1005's exit function
[dll] sane_exit: calling backend `hp5590's exit function
[dll] sane_exit: calling backend `hp5400's exit function
[dll] sane_exit: calling backend `hp4200's exit function
[dll] sane_exit: calling backend `hp3500's exit function
[dll] sane_exit: calling backend `hpsj5s's exit function
[dll] sane_exit: calling backend `hp3900's exit function
[dll] sane_exit: calling backend `hp's exit function
[dll] sane_exit: calling backend `gt68xx's exit function
[dll] sane_exit: calling backend `genesys's exit function
[dll] sane_exit: calling backend `fujitsu's exit function
[dll] sane_exit: calling backend `epsonds's exit function
[dll] sane_exit: calling backend `epson2's exit function
[dll] sane_exit: calling backend `epjitsu's exit function
[dll] sane_exit: calling backend `dmc's exit function
[dll] sane_exit: calling backend `dell1600n_net's exit function
[dll] sane_exit: calling backend `coolscan3's exit function
[dll] sane_exit: calling backend `coolscan's exit function
[dll] sane_exit: calling backend `cardscan's exit function
[dll] sane_exit: calling backend `canon_dr's exit function
[dll] sane_exit: calling backend `canon630u's exit function
[dll] sane_exit: calling backend `canon's exit function
[dll] sane_exit: calling backend `bh's exit function
[dll] sane_exit: calling backend `artec_eplus48u's exit function
[dll] sane_exit: calling backend `artec's exit function
[dll] sane_exit: calling backend `avision's exit function
[dll] sane_exit: calling backend `apple's exit function
[dll] sane_exit: calling backend `agfafocus's exit function
[dll] sane_exit: calling backend `abaton's exit function
[dll] sane_exit: calling backend `net's exit function
[dll] sane_exit: calling backend `ls5000's exit function
[dll] sane_exit: calling backend `hpaio's exit function
[dll] sane_exit: finished
-----------------------------
-----------------------------
/usr/local/Brother/sane/brsanenetdevice3.cfg:
-----------------------------
/usr/local/Brother/sane/Brsane3.ini:
[Support Model]
0x0206,14,2,"DCP-145C"
0x0204,14,2,"DCP-165C"
0x0205,13,2,"DCP-185C"
0x0201,14,2,"DCP-385C"
0x0200,14,2,"DCP-585CW"
0x01ff,13,2,"DCP-535CN"
0x01fe,14,1,"MFC-250C"
0x01fd,13,1,"MFC-290C"
0x01fb,13,1,"MFC-490CW"
0x01fa,13,1,"MFC-490CN"
0x01f9,13,1,"MFC-790CW"
0x01f8,13,1,"MFC-990CW"
0x01f7,14,1,"MFC-670CD"
0x01f6,13,1,"MFC-930CDN"
0x01f5,13,1,"MFC-5490CN"
0x01f4,13,1,"MFC-5890CN"
0x01f1,13,2,"DCP-6690CW"
0x01f3,13,1,"MFC-6490CW"
0x01f2,13,1,"MFC-6490CN"
0x01f0,13,1,"MFC-6890CDW"
0x01ef,13,1,"MFC-6890CN"
0x0207,14,2,"DCP-163C"
0x0208,14,2,"DCP-167C"
0x0203,14,2,"DCP-383C"
0x0202,14,2,"DCP-387C"
0x01fc,13,1,"MFC-297C"
0x01ee,1,1,"MFC-7450",131,4
0x01ed,1,1,"MFC-7840N",131,4
0x01eb,1,1,"MFC-7320",131,4
0x01ea,2,2,"DCP-7030",131,4
0x01e9,1,2,"DCP-7040",131,4
0x01e8,1,2,"DCP-7045N",131,4
0x01e7,1,1,"MFC-7340",131,4
0x01e6,1,1,"MFC-7440N",131,4
0x01e5,1,1,"MFC-7840W",131,4
0x0218,17,1,"DCP-8080DN",133,4
0x021f,117,1,"DCP-8085DN",133,4
0x0217,17,1,"MFC-8480DN",133,4
0x0215,117,1,"MFC-8890DW",133,4
[ModelTypeName]
1=MFC Scanner
2=DCP Scanner
[Driver]
scanfast24=0
NoUseCM=0
compression=1
Inqueue=32000
LogFile=0
xshift_c=0
-----------------------------
/usr/local/Brother/sane/models3/ext3.ini:
[Support Model]
0x01c9, 17,2,"DCP-9040CN",133,4
0x01ca, 17,1,"MFC-9440CN",133,4
0x01cb, 117,2,"DCP-9045CDN",133,4
0x01cc, 117,1,"MFC-9840CDW",133,4
0x01ec, 117,1,"MFC-9640CW",133,4
0x020d ,17,1,"MFC-9450CDN",133,4
0x020c ,17,2,"DCP-9042CDN",133,4
-----------------------------
/usr/local/Brother/sane/models3/ext4.ini:
[Support Model]
0x0257,13,2,"DCP-J715W"
0x025d,13,1,"MFC-J615W"
0x0254,14,2,"DCP-J315W"
0x025B,14,1,"MFC-J265W"
0x026B,13,1,"MFC-J630W"
-----------------------------
/usr/local/Brother/sane/models3/ext5.ini:
[Support Model]
0x0258,13,2,"DCP-J715N"
0x025e,13,1,"MFC-J615N"
0x0256,14,2,"DCP-J515N"
0x240,13,1,"MFC-J950DN"
0x25f,14,1,"MFC-J700D"
0x260,14,1,"MFC-J800D"
0x261,14,1,"MFC-J850DN"
0x0278,13,1,"MFC-J410W"
0x026f,14,1,"MFC-J270W"
0x026e,14,1,"MFC-J855DN"
0x026d,14,1,"MFC-J805D"
0x234,14,2,"DCP-373CW"
0x239,14,1,"MFC-253CW"
0x253,14,2,"DCP-J125"
0x255,14,2,"DCP-J515W"
0x259,14,1,"MFC-J220"
0x25a,13,1,"MFC-J410"
0x25c,13,1,"MFC-J415W"
0x0276,13,1,"MFC-5895CW"
-----------------------------
/usr/local/Brother/sane/models3/ext2.ini:
[Support Model]
0x23e,14,2,"DCP-197C"
0x235,14,2,"DCP-377CW"
0x23a,14,1,"MFC-257CW"
-----------------------------
/usr/local/Brother/sane/models3/ext1.ini:
[Support Model]
0x0222,14,2,"DCP-195C"
0x0223,14,2,"DCP-365CN"
0x0224,14,2,"DCP-375CW"
0x0225,14,2,"DCP-395CN"
0x0229,13,1,"MFC-295CN"
0x022a,13,1,"MFC-495CW"
0x022c,13,1,"MFC-795CW"
0x0228,14,1,"MFC-255CW"
0x0236,14,2,"DCP-390CN"
0x0227,13,2,"DCP-595CN"
0x022b,13,1,"MFC-495CN"
0x022d,14,1,"MFC-675CD"
0x022e,14,1,"MFC-695CDN"
0x022f,14,1,"MFC-735CD"
0x0230,13,1,"MFC-935CDN"
0x021b,17,2,"DCP-8070D",133,4
0x021a,17,1,"MFC-8370DN",133,4
0x0219,117,1,"MFC-8380DN",133,4
0x023f,117,1,"MFC-8680DN",133,4
0x0216,117,1,"MFC-8880DN",133,4
0x021d,17,1,"MFC-9120CN"
0x021c,17,1,"MFC-9320CW"
0x0220,17,1,"MFC-9010CN"
0x021e,17,2,"DCP-9010CN"
-----------------------------
MODEL:"DCP-9040CN",ID:0x4f9:0x1c9,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9440CN",ID:0x4f9:0x1ca,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-9045CDN",ID:0x4f9:0x1cb,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9840CDW",ID:0x4f9:0x1cc,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9640CW",ID:0x4f9:0x1ec,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9450CDN",ID:0x4f9:0x20d,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-9042CDN",ID:0x4f9:0x20c,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-J715W",ID:0x4f9:0x257,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J615W",ID:0x4f9:0x25d,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J315W",ID:0x4f9:0x254,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J265W",ID:0x4f9:0x25b,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J630W",ID:0x4f9:0x26b,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J715N",ID:0x4f9:0x258,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J615N",ID:0x4f9:0x25e,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J515N",ID:0x4f9:0x256,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J950DN",ID:0x4f9:0x240,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J700D",ID:0x4f9:0x25f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J800D",ID:0x4f9:0x260,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J850DN",ID:0x4f9:0x261,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J410W",ID:0x4f9:0x278,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J270W",ID:0x4f9:0x26f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J855DN",ID:0x4f9:0x26e,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J805D",ID:0x4f9:0x26d,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-373CW",ID:0x4f9:0x234,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-253CW",ID:0x4f9:0x239,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J125",ID:0x4f9:0x253,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J515W",ID:0x4f9:0x255,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J220",ID:0x4f9:0x259,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J410",ID:0x4f9:0x25a,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J415W",ID:0x4f9:0x25c,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5895CW",ID:0x4f9:0x276,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-197C",ID:0x4f9:0x23e,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-377CW",ID:0x4f9:0x235,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-257CW",ID:0x4f9:0x23a,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-195C",ID:0x4f9:0x222,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-365CN",ID:0x4f9:0x223,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-375CW",ID:0x4f9:0x224,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-395CN",ID:0x4f9:0x225,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-295CN",ID:0x4f9:0x229,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-495CW",ID:0x4f9:0x22a,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-795CW",ID:0x4f9:0x22c,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-255CW",ID:0x4f9:0x228,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-390CN",ID:0x4f9:0x236,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-595CN",ID:0x4f9:0x227,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-495CN",ID:0x4f9:0x22b,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-675CD",ID:0x4f9:0x22d,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-695CDN",ID:0x4f9:0x22e,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-735CD",ID:0x4f9:0x22f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-935CDN",ID:0x4f9:0x230,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-8070D",ID:0x4f9:0x21b,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8370DN",ID:0x4f9:0x21a,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8380DN",ID:0x4f9:0x219,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8680DN",ID:0x4f9:0x23f,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8880DN",ID:0x4f9:0x216,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9120CN",ID:0x4f9:0x21d,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-9320CW",ID:0x4f9:0x21c,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-9010CN",ID:0x4f9:0x220,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-9010CN",ID:0x4f9:0x21e,TYPE:17,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-145C",ID:0x4f9:0x206,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-165C",ID:0x4f9:0x204,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-185C",ID:0x4f9:0x205,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-385C",ID:0x4f9:0x201,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-585CW",ID:0x4f9:0x200,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-535CN",ID:0x4f9:0x1ff,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-250C",ID:0x4f9:0x1fe,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-290C",ID:0x4f9:0x1fd,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-490CW",ID:0x4f9:0x1fb,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-490CN",ID:0x4f9:0x1fa,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-790CW",ID:0x4f9:0x1f9,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-990CW",ID:0x4f9:0x1f8,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-670CD",ID:0x4f9:0x1f7,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-930CDN",ID:0x4f9:0x1f6,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5490CN",ID:0x4f9:0x1f5,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5890CN",ID:0x4f9:0x1f4,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-6690CW",ID:0x4f9:0x1f1,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6490CW",ID:0x4f9:0x1f3,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6490CN",ID:0x4f9:0x1f2,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6890CDW",ID:0x4f9:0x1f0,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6890CN",ID:0x4f9:0x1ef,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-163C",ID:0x4f9:0x207,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-167C",ID:0x4f9:0x208,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-383C",ID:0x4f9:0x203,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-387C",ID:0x4f9:0x202,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-297C",ID:0x4f9:0x1fc,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-7450",ID:0x4f9:0x1ee,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7840N",ID:0x4f9:0x1ed,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7320",ID:0x4f9:0x1eb,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7030",ID:0x4f9:0x1ea,TYPE:2,2,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7040",ID:0x4f9:0x1e9,TYPE:1,2,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7045N",ID:0x4f9:0x1e8,TYPE:1,2,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7340",ID:0x4f9:0x1e7,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7440N",ID:0x4f9:0x1e6,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7840W",ID:0x4f9:0x1e5,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:,ID:0x4f9:0x1,TYPE:35,65535,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-8080DN",ID:0x4f9:0x218,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-8085DN",ID:0x4f9:0x21f,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8480DN",ID:0x4f9:0x217,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8890DW",ID:0x4f9:0x215,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
-----------------------------
0 "DCP-9040CN"
1 "MFC-9440CN"
2 "DCP-9045CDN"
3 "MFC-9840CDW"
4 "MFC-9640CW"
5 "MFC-9450CDN"
6 "DCP-9042CDN"
7 "DCP-J715W"
8 "MFC-J615W"
9 "DCP-J315W"
10 "MFC-J265W"
11 "MFC-J630W"
12 "DCP-J715N"
13 "MFC-J615N"
14 "DCP-J515N"
15 "MFC-J950DN"
16 "MFC-J700D"
17 "MFC-J800D"
18 "MFC-J850DN"
19 "MFC-J410W"
20 "MFC-J270W"
21 "MFC-J855DN"
22 "MFC-J805D"
23 "DCP-373CW"
24 "MFC-253CW"
25 "DCP-J125"
26 "DCP-J515W"
27 "MFC-J220"
28 "MFC-J410"
29 "MFC-J415W"
30 "MFC-5895CW"
31 "DCP-197C"
32 "DCP-377CW"
33 "MFC-257CW"
34 "DCP-195C"
35 "DCP-365CN"
36 "DCP-375CW"
37 "DCP-395CN"
38 "MFC-295CN"
39 "MFC-495CW"
40 "MFC-795CW"
41 "MFC-255CW"
42 "DCP-390CN"
43 "DCP-595CN"
44 "MFC-495CN"
45 "MFC-675CD"
46 "MFC-695CDN"
47 "MFC-735CD"
48 "MFC-935CDN"
49 "DCP-8070D"
50 "MFC-8370DN"
51 "MFC-8380DN"
52 "MFC-8680DN"
53 "MFC-8880DN"
54 "MFC-9120CN"
55 "MFC-9320CW"
56 "MFC-9010CN"
57 "DCP-9010CN"
58 "DCP-145C"
59 "DCP-165C"
60 "DCP-185C"
61 "DCP-385C"
62 "DCP-585CW"
63 "DCP-535CN"
64 "MFC-250C"
65 "MFC-290C"
66 "MFC-490CW"
67 "MFC-490CN"
68 "MFC-790CW"
69 "MFC-990CW"
70 "MFC-670CD"
71 "MFC-930CDN"
72 "MFC-5490CN"
73 "MFC-5890CN"
74 "DCP-6690CW"
75 "MFC-6490CW"
76 "MFC-6490CN"
77 "MFC-6890CDW"
78 "MFC-6890CN"
79 "DCP-163C"
80 "DCP-167C"
81 "DCP-383C"
82 "DCP-387C"
83 "MFC-297C"
84 "MFC-7450"
85 "MFC-7840N"
86 "MFC-7320"
87 "DCP-7030"
88 "DCP-7040"
89 "DCP-7045N"
90 "MFC-7340"
91 "MFC-7440N"
92 "MFC-7840W"
93
94 "DCP-8080DN"
95 "DCP-8085DN"
96 "MFC-8480DN"
97 "MFC-8890DW"
Devices on network
pingHors ligne
#130 Le 29/08/2017, à 00:05
- abelthorne
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
A priori IPv4. C'est seulement quand il sera connecté que tu devras me donner le retour de la commande brsaneconfig3 -d. Et tu la lanceras dans un nouveau terminal, parce qu'il y a toujours la variable pour afficher les infos de debug de scanimage, ça donne un peu trop d'infos pour s'y retrouver.
EDIT : en fait, la commande, c'est surtout pour avoir l'IP de ton scanner. Si tu peux l'avoir autrement, tu peux la donner directement.
(Et je vais arrêter là pour ce soir.)
Dernière modification par abelthorne (Le 29/08/2017, à 00:12)
Hors ligne
#131 Le 29/08/2017, à 00:13
- julien_sen
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Ça marche. Il faut que je lise la doc. J'en ai peut-être pour un moment.
Hors ligne
#132 Le 31/08/2017, à 20:21
- julien_sen
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Alors : j'ai lu la doc et tenté quelques manip directement sur l'appareil mais je t'avoue que je suis largué.
L'imprimante n'apparaît pas dans le menu paramètres/imprimantes/imprimante réseau ; son adresse IP est 000.000.000.000... Pour obtenir la bonne adresse, j'ai apparemment besoin d'un câble ethernet qui est actuellement enfoui dans un carton (car je déménage incessamment). Bref, tout ceci plus nos précédentes tentatives me découragent un peu malgré tes conseils avisés 
Hors ligne
#133 Le 31/08/2017, à 22:02
- abelthorne
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Est-ce que tu as pu connecter l'imprimante à ton réseau wi-fi (choisir le réseau, entrer le mot de passe) ? Si c'est le cas, tu peux relancer la commande brsaneconfig3 -d, il devrait y avoir son adresse IP quelque part dans le retour. Ça m'étonne un peu qu'il y ait besoin de la connecter en ethernet pour régler ça. En tout cas, ça coûte rien de vérifier.
Hors ligne
#134 Le 02/09/2017, à 18:37
- julien_sen
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
j'ai retrouvé mon câble ethernet !
Je ne crois pas avoir réussi à connecter le scanner au réseau (comment le vérifier ?). Je suis allé sur le site Brother qui indique l'adresse IP par défaut de leurs appareils (192.0.0.192). J'ai donc entré cette adresse dans le scanner.
J'ai suivi cette doc : https://doc.ubuntu-fr.org/tutoriel/util … _en_reseau ; sans beaucoup de succès.
La commande brsaneconfig3 -d renvoie :
cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda2 during installation
UUID=a4d11e7c-40c1-473b-af79-4923773df2a8 / ext4 errors=remount-ro 0 1
# /boot/efi was on /dev/sda1 during installation
#UUID=81CE-0F89 /boot/efi vfat umask=0077 0 1
/swapfile none swap sw 0 0
UUID=81CE-0F89 /boot/efi vfat defaults 0 1
-----------------------------
sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
could not open USB device 0x1d6b/0x0003 at 002:001: Access denied (insufficient permissions)
could not open USB device 0x04f2/0xb469 at 001:003: Access denied (insufficient permissions)
found USB scanner (vendor=0x04f9, product=0x01e8) at libusb:001:009
could not open USB device 0x04ca/0x300b at 001:006: Access denied (insufficient permissions)
could not open USB device 0x05e3/0x0608 at 001:002: Access denied (insufficient permissions)
could not open USB device 0x046d/0xc077 at 001:008: Access denied (insufficient permissions)
could not open USB device 0x1d6b/0x0002 at 001:001: Access denied (insufficient permissions)
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
-----------------------------
ls -R -all /proc/bus/usb
ls: impossible d'accéder à '/proc/bus/usb': Aucun fichier ou dossier de ce type
-----------------------------
cat /proc/bus/usb/devices
cat: /proc/bus/usb/devices: Aucun fichier ou dossier de ce type
-----------------------------
scanimage -L
device `brother3:bus2;dev1' is a Brother DCP-7045N USB scanner
-----------------------------
-----------------------------
/usr/local/Brother/sane/brsanenetdevice3.cfg:
-----------------------------
/usr/local/Brother/sane/Brsane3.ini:
[Support Model]
0x0206,14,2,"DCP-145C"
0x0204,14,2,"DCP-165C"
0x0205,13,2,"DCP-185C"
0x0201,14,2,"DCP-385C"
0x0200,14,2,"DCP-585CW"
0x01ff,13,2,"DCP-535CN"
0x01fe,14,1,"MFC-250C"
0x01fd,13,1,"MFC-290C"
0x01fb,13,1,"MFC-490CW"
0x01fa,13,1,"MFC-490CN"
0x01f9,13,1,"MFC-790CW"
0x01f8,13,1,"MFC-990CW"
0x01f7,14,1,"MFC-670CD"
0x01f6,13,1,"MFC-930CDN"
0x01f5,13,1,"MFC-5490CN"
0x01f4,13,1,"MFC-5890CN"
0x01f1,13,2,"DCP-6690CW"
0x01f3,13,1,"MFC-6490CW"
0x01f2,13,1,"MFC-6490CN"
0x01f0,13,1,"MFC-6890CDW"
0x01ef,13,1,"MFC-6890CN"
0x0207,14,2,"DCP-163C"
0x0208,14,2,"DCP-167C"
0x0203,14,2,"DCP-383C"
0x0202,14,2,"DCP-387C"
0x01fc,13,1,"MFC-297C"
0x01ee,1,1,"MFC-7450",131,4
0x01ed,1,1,"MFC-7840N",131,4
0x01eb,1,1,"MFC-7320",131,4
0x01ea,2,2,"DCP-7030",131,4
0x01e9,1,2,"DCP-7040",131,4
0x01e8,1,2,"DCP-7045N",131,4
0x01e7,1,1,"MFC-7340",131,4
0x01e6,1,1,"MFC-7440N",131,4
0x01e5,1,1,"MFC-7840W",131,4
0x0218,17,1,"DCP-8080DN",133,4
0x021f,117,1,"DCP-8085DN",133,4
0x0217,17,1,"MFC-8480DN",133,4
0x0215,117,1,"MFC-8890DW",133,4
[ModelTypeName]
1=MFC Scanner
2=DCP Scanner
[Driver]
scanfast24=0
NoUseCM=0
compression=1
Inqueue=32000
LogFile=0
xshift_c=0
-----------------------------
/usr/local/Brother/sane/models3/ext3.ini:
[Support Model]
0x01c9, 17,2,"DCP-9040CN",133,4
0x01ca, 17,1,"MFC-9440CN",133,4
0x01cb, 117,2,"DCP-9045CDN",133,4
0x01cc, 117,1,"MFC-9840CDW",133,4
0x01ec, 117,1,"MFC-9640CW",133,4
0x020d ,17,1,"MFC-9450CDN",133,4
0x020c ,17,2,"DCP-9042CDN",133,4
-----------------------------
/usr/local/Brother/sane/models3/ext4.ini:
[Support Model]
0x0257,13,2,"DCP-J715W"
0x025d,13,1,"MFC-J615W"
0x0254,14,2,"DCP-J315W"
0x025B,14,1,"MFC-J265W"
0x026B,13,1,"MFC-J630W"
-----------------------------
/usr/local/Brother/sane/models3/ext5.ini:
[Support Model]
0x0258,13,2,"DCP-J715N"
0x025e,13,1,"MFC-J615N"
0x0256,14,2,"DCP-J515N"
0x240,13,1,"MFC-J950DN"
0x25f,14,1,"MFC-J700D"
0x260,14,1,"MFC-J800D"
0x261,14,1,"MFC-J850DN"
0x0278,13,1,"MFC-J410W"
0x026f,14,1,"MFC-J270W"
0x026e,14,1,"MFC-J855DN"
0x026d,14,1,"MFC-J805D"
0x234,14,2,"DCP-373CW"
0x239,14,1,"MFC-253CW"
0x253,14,2,"DCP-J125"
0x255,14,2,"DCP-J515W"
0x259,14,1,"MFC-J220"
0x25a,13,1,"MFC-J410"
0x25c,13,1,"MFC-J415W"
0x0276,13,1,"MFC-5895CW"
-----------------------------
/usr/local/Brother/sane/models3/ext2.ini:
[Support Model]
0x23e,14,2,"DCP-197C"
0x235,14,2,"DCP-377CW"
0x23a,14,1,"MFC-257CW"
-----------------------------
/usr/local/Brother/sane/models3/ext1.ini:
[Support Model]
0x0222,14,2,"DCP-195C"
0x0223,14,2,"DCP-365CN"
0x0224,14,2,"DCP-375CW"
0x0225,14,2,"DCP-395CN"
0x0229,13,1,"MFC-295CN"
0x022a,13,1,"MFC-495CW"
0x022c,13,1,"MFC-795CW"
0x0228,14,1,"MFC-255CW"
0x0236,14,2,"DCP-390CN"
0x0227,13,2,"DCP-595CN"
0x022b,13,1,"MFC-495CN"
0x022d,14,1,"MFC-675CD"
0x022e,14,1,"MFC-695CDN"
0x022f,14,1,"MFC-735CD"
0x0230,13,1,"MFC-935CDN"
0x021b,17,2,"DCP-8070D",133,4
0x021a,17,1,"MFC-8370DN",133,4
0x0219,117,1,"MFC-8380DN",133,4
0x023f,117,1,"MFC-8680DN",133,4
0x0216,117,1,"MFC-8880DN",133,4
0x021d,17,1,"MFC-9120CN"
0x021c,17,1,"MFC-9320CW"
0x0220,17,1,"MFC-9010CN"
0x021e,17,2,"DCP-9010CN"
-----------------------------
MODEL:"DCP-9040CN",ID:0x4f9:0x1c9,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9440CN",ID:0x4f9:0x1ca,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-9045CDN",ID:0x4f9:0x1cb,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9840CDW",ID:0x4f9:0x1cc,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9640CW",ID:0x4f9:0x1ec,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9450CDN",ID:0x4f9:0x20d,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-9042CDN",ID:0x4f9:0x20c,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-J715W",ID:0x4f9:0x257,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J615W",ID:0x4f9:0x25d,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J315W",ID:0x4f9:0x254,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J265W",ID:0x4f9:0x25b,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J630W",ID:0x4f9:0x26b,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J715N",ID:0x4f9:0x258,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J615N",ID:0x4f9:0x25e,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J515N",ID:0x4f9:0x256,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J950DN",ID:0x4f9:0x240,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J700D",ID:0x4f9:0x25f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J800D",ID:0x4f9:0x260,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J850DN",ID:0x4f9:0x261,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J410W",ID:0x4f9:0x278,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J270W",ID:0x4f9:0x26f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J855DN",ID:0x4f9:0x26e,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J805D",ID:0x4f9:0x26d,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-373CW",ID:0x4f9:0x234,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-253CW",ID:0x4f9:0x239,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J125",ID:0x4f9:0x253,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-J515W",ID:0x4f9:0x255,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J220",ID:0x4f9:0x259,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J410",ID:0x4f9:0x25a,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-J415W",ID:0x4f9:0x25c,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5895CW",ID:0x4f9:0x276,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-197C",ID:0x4f9:0x23e,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-377CW",ID:0x4f9:0x235,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-257CW",ID:0x4f9:0x23a,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-195C",ID:0x4f9:0x222,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-365CN",ID:0x4f9:0x223,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-375CW",ID:0x4f9:0x224,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-395CN",ID:0x4f9:0x225,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-295CN",ID:0x4f9:0x229,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-495CW",ID:0x4f9:0x22a,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-795CW",ID:0x4f9:0x22c,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-255CW",ID:0x4f9:0x228,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-390CN",ID:0x4f9:0x236,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-595CN",ID:0x4f9:0x227,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-495CN",ID:0x4f9:0x22b,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-675CD",ID:0x4f9:0x22d,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-695CDN",ID:0x4f9:0x22e,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-735CD",ID:0x4f9:0x22f,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-935CDN",ID:0x4f9:0x230,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-8070D",ID:0x4f9:0x21b,TYPE:17,2,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8370DN",ID:0x4f9:0x21a,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8380DN",ID:0x4f9:0x219,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8680DN",ID:0x4f9:0x23f,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8880DN",ID:0x4f9:0x216,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-9120CN",ID:0x4f9:0x21d,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-9320CW",ID:0x4f9:0x21c,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-9010CN",ID:0x4f9:0x220,TYPE:17,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-9010CN",ID:0x4f9:0x21e,TYPE:17,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-145C",ID:0x4f9:0x206,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-165C",ID:0x4f9:0x204,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-185C",ID:0x4f9:0x205,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-385C",ID:0x4f9:0x201,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-585CW",ID:0x4f9:0x200,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-535CN",ID:0x4f9:0x1ff,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-250C",ID:0x4f9:0x1fe,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-290C",ID:0x4f9:0x1fd,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-490CW",ID:0x4f9:0x1fb,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-490CN",ID:0x4f9:0x1fa,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-790CW",ID:0x4f9:0x1f9,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-990CW",ID:0x4f9:0x1f8,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-670CD",ID:0x4f9:0x1f7,TYPE:14,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-930CDN",ID:0x4f9:0x1f6,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5490CN",ID:0x4f9:0x1f5,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-5890CN",ID:0x4f9:0x1f4,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-6690CW",ID:0x4f9:0x1f1,TYPE:13,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6490CW",ID:0x4f9:0x1f3,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6490CN",ID:0x4f9:0x1f2,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6890CDW",ID:0x4f9:0x1f0,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-6890CN",ID:0x4f9:0x1ef,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-163C",ID:0x4f9:0x207,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-167C",ID:0x4f9:0x208,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-383C",ID:0x4f9:0x203,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-387C",ID:0x4f9:0x202,TYPE:14,2,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-297C",ID:0x4f9:0x1fc,TYPE:13,1,RE:0xffff,WE:0xffff CM:,,
MODEL:"MFC-7450",ID:0x4f9:0x1ee,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7840N",ID:0x4f9:0x1ed,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7320",ID:0x4f9:0x1eb,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7030",ID:0x4f9:0x1ea,TYPE:2,2,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7040",ID:0x4f9:0x1e9,TYPE:1,2,RE:0x83,WE:0x4 CM:,,
MODEL:"DCP-7045N",ID:0x4f9:0x1e8,TYPE:1,2,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7340",ID:0x4f9:0x1e7,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7440N",ID:0x4f9:0x1e6,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:"MFC-7840W",ID:0x4f9:0x1e5,TYPE:1,1,RE:0x83,WE:0x4 CM:,,
MODEL:,ID:0x4f9:0x1,TYPE:35,65535,RE:0xffff,WE:0xffff CM:,,
MODEL:"DCP-8080DN",ID:0x4f9:0x218,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"DCP-8085DN",ID:0x4f9:0x21f,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8480DN",ID:0x4f9:0x217,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
MODEL:"MFC-8890DW",ID:0x4f9:0x215,TYPE:17,1,RE:0x85,WE:0x4 CM:,,
-----------------------------
0 "DCP-9040CN"
1 "MFC-9440CN"
2 "DCP-9045CDN"
3 "MFC-9840CDW"
4 "MFC-9640CW"
5 "MFC-9450CDN"
6 "DCP-9042CDN"
7 "DCP-J715W"
8 "MFC-J615W"
9 "DCP-J315W"
10 "MFC-J265W"
11 "MFC-J630W"
12 "DCP-J715N"
13 "MFC-J615N"
14 "DCP-J515N"
15 "MFC-J950DN"
16 "MFC-J700D"
17 "MFC-J800D"
18 "MFC-J850DN"
19 "MFC-J410W"
20 "MFC-J270W"
21 "MFC-J855DN"
22 "MFC-J805D"
23 "DCP-373CW"
24 "MFC-253CW"
25 "DCP-J125"
26 "DCP-J515W"
27 "MFC-J220"
28 "MFC-J410"
29 "MFC-J415W"
30 "MFC-5895CW"
31 "DCP-197C"
32 "DCP-377CW"
33 "MFC-257CW"
34 "DCP-195C"
35 "DCP-365CN"
36 "DCP-375CW"
37 "DCP-395CN"
38 "MFC-295CN"
39 "MFC-495CW"
40 "MFC-795CW"
41 "MFC-255CW"
42 "DCP-390CN"
43 "DCP-595CN"
44 "MFC-495CN"
45 "MFC-675CD"
46 "MFC-695CDN"
47 "MFC-735CD"
48 "MFC-935CDN"
49 "DCP-8070D"
50 "MFC-8370DN"
51 "MFC-8380DN"
52 "MFC-8680DN"
53 "MFC-8880DN"
54 "MFC-9120CN"
55 "MFC-9320CW"
56 "MFC-9010CN"
57 "DCP-9010CN"
58 "DCP-145C"
59 "DCP-165C"
60 "DCP-185C"
61 "DCP-385C"
62 "DCP-585CW"
63 "DCP-535CN"
64 "MFC-250C"
65 "MFC-290C"
66 "MFC-490CW"
67 "MFC-490CN"
68 "MFC-790CW"
69 "MFC-990CW"
70 "MFC-670CD"
71 "MFC-930CDN"
72 "MFC-5490CN"
73 "MFC-5890CN"
74 "DCP-6690CW"
75 "MFC-6490CW"
76 "MFC-6490CN"
77 "MFC-6890CDW"
78 "MFC-6890CN"
79 "DCP-163C"
80 "DCP-167C"
81 "DCP-383C"
82 "DCP-387C"
83 "MFC-297C"
84 "MFC-7450"
85 "MFC-7840N"
86 "MFC-7320"
87 "DCP-7030"
88 "DCP-7040"
89 "DCP-7045N"
90 "MFC-7340"
91 "MFC-7440N"
92 "MFC-7840W"
93
94 "DCP-8080DN"
95 "DCP-8085DN"
96 "MFC-8480DN"
97 "MFC-8890DW"
Devices on network
pingC'est toujours le flou artistique !
Hors ligne
#135 Le 02/09/2017, à 18:53
- abelthorne
Re : Imprimante-scanner Brother (DCP-7045N) ne fonctionne plus
Il voit toujours ton scanner USB mais rien comme scanner réseau. Je suppose que sur l'imprimante / scanner, tu as une manip pour choisir le réseau wi-fi sur lequel te connecter, non ? Cela dit, en ethernet, ça devrait fonctionner directement. Tu es derrière une box de FAI, je suppose ? elle est bien configurée en mode routeur ?
Hors ligne