#26 Le 22/09/2017, à 13:06
- fwehrli
Re : {résolu}Bug complet xubuntu
Voici un premier résultat du contrôle de l'état de la partition Linux ext4:
root@xubuntu:~# sudo smartctl -s on -a /dev/sda6
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-32-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-08A23T1
Serial Number: WD-WX11A41D3382
LU WWN Device Id: 5 0014ee 65689137a
Firmware Version: 02.01A02
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Sep 22 11:04:29 2017 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 77) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 149 132 021 Pre-fail Always - 1516
4 Start_Stop_Count 0x0032 058 058 000 Old_age Always - 42362
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5319
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3092
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 015 015 000 Old_age Always - 555211
194 Temperature_Celsius 0x0022 085 073 000 Old_age Always - 58
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 094 094 000 Old_age Always - 4805
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1194 -
# 2 Short offline Completed without error 00% 1034 -
# 3 Short offline Completed without error 00% 947 -
# 4 Short offline Completed without error 00% 921 -
# 5 Short offline Completed without error 00% 920 -
# 6 Short offline Completed without error 00% 855 -
# 7 Short offline Completed without error 00% 753 -
# 8 Short offline Completed without error 00% 576 -
# 9 Short offline Aborted by host 10% 483 -
#10 Short offline Completed without error 00% 441 -
#11 Short offline Completed without error 00% 368 -
#12 Short offline Completed without error 00% 292 -
#13 Short offline Completed without error 00% 277 -
#14 Short offline Completed without error 00% 234 -
#15 Short offline Completed without error 00% 208 -
#16 Short offline Completed without error 00% 167 -
#17 Short offline Completed without error 00% 150 -
#18 Short offline Completed without error 00% 108 -
#19 Short offline Completed without error 00% 81 -
#20 Short offline Completed without error 00% 7 -
#21 Vendor (0x50) Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@xubuntu:~#
Hors ligne
#27 Le 22/09/2017, à 13:07
- fwehrli
Re : {résolu}Bug complet xubuntu
La même chose pour la partition swap:
root@xubuntu:~# sudo smartctl -s on -a /dev/sda7
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-32-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-08A23T1
Serial Number: WD-WX11A41D3382
LU WWN Device Id: 5 0014ee 65689137a
Firmware Version: 02.01A02
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Sep 22 11:06:54 2017 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 77) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 149 132 021 Pre-fail Always - 1516
4 Start_Stop_Count 0x0032 058 058 000 Old_age Always - 42362
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5319
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3092
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 015 015 000 Old_age Always - 555211
194 Temperature_Celsius 0x0022 085 073 000 Old_age Always - 58
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 094 094 000 Old_age Always - 4805
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1194 -
# 2 Short offline Completed without error 00% 1034 -
# 3 Short offline Completed without error 00% 947 -
# 4 Short offline Completed without error 00% 921 -
# 5 Short offline Completed without error 00% 920 -
# 6 Short offline Completed without error 00% 855 -
# 7 Short offline Completed without error 00% 753 -
# 8 Short offline Completed without error 00% 576 -
# 9 Short offline Aborted by host 10% 483 -
#10 Short offline Completed without error 00% 441 -
#11 Short offline Completed without error 00% 368 -
#12 Short offline Completed without error 00% 292 -
#13 Short offline Completed without error 00% 277 -
#14 Short offline Completed without error 00% 234 -
#15 Short offline Completed without error 00% 208 -
#16 Short offline Completed without error 00% 167 -
#17 Short offline Completed without error 00% 150 -
#18 Short offline Completed without error 00% 108 -
#19 Short offline Completed without error 00% 81 -
#20 Short offline Completed without error 00% 7 -
#21 Vendor (0x50) Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@xubuntu:~#
Hors ligne
#28 Le 22/09/2017, à 13:13
- fwehrli
Re : {résolu}Bug complet xubuntu
J'ai fait également un contrôle sur windows 7 sur ses deux partitions, aucun secteur défectueux.Par contre j'ai installé gsmartctrl.
Il refuse d'analyser le disque:
root@xubuntu:~# gsmartcontrol
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Rotation Rate"
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Vendor"
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Product"
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Revision"
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Logical block size"
<warn> [app] SmartctlParser::parse_section_info_property(): Unknown property "Device type"
terminate called after throwing an instance of 'std::out_of_range'
what(): basic_string::substr
Abandon (core dumped)
Hors ligne
#29 Le 22/09/2017, à 15:11
- moko138
Re : {résolu}Bug complet xubuntu
Sauf disques en RAID (cf. man smartctl), ne mets jamais de nombre après /dev/sdx quand tu demandes un rapport SMART.
Dans le lien que je t'ai donné en #4, il n'y a pas de nombre.
Dans la Doc smartmontools, il n'y a pas de nombre.
Explication :
Les données smart (contrairement aux badblocks) ne distinguent pas les partitions, elles portent sur le disque tout entier et sont stockées dans une puce du circuit imprimé, pas sur le plateau.
Au mieux, un nombre ne sert à rien.
Au pire, je me demande - à confirmer - si ça ne supprime pas quelques infos.
- -
Extraits du kern.log obtenu (message #20) en session live :
Sep 20 07:39:59 xubuntu kernel: [ 99.657395] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20131115/utaddress-251)
Sep 20 07:39:59 xubuntu kernel: [ 99.657404] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Sep 20 07:39:59 xubuntu kernel: [ 99.657409] ACPI Warning: 0x00000000000011b0-0x00000000000011bf SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
Sep 20 07:39:59 xubuntu kernel: [ 99.657413] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Sep 20 07:39:59 xubuntu kernel: [ 99.657414] ACPI Warning: 0x0000000000001180-0x00000000000011af SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
Sep 20 07:39:59 xubuntu kernel: [ 99.657418] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
Sep 20 07:39:59 xubuntu kernel: [ 99.657420] lpc_ich: Resource conflict(s) found affecting gpio_ich
Va faire un tour dans ton bios et dis-nous quels sont les options activées et non activées, concernant l'ACPI.
- -
Sep 20 07:40:08 xubuntu kernel: [ 108.724261] thinkpad_acpi: ThinkPad ACPI Extras v0.25
Sep 20 07:40:08 xubuntu kernel: [ 108.724266] thinkpad_acpi: [url]http://ibm-acpi.sf.net/[/url]
Sep 20 07:40:08 xubuntu kernel: [ 108.724267] thinkpad_acpi: ThinkPad BIOS 6JET88WW (1.46 ), EC 6JHT68WW-1.280000
Sep 20 07:40:08 xubuntu kernel: [ 108.724269] thinkpad_acpi: Lenovo ThinkPad SL510, model 2847D8G
Sep 20 07:40:08 xubuntu kernel: [ 108.724522] thinkpad_acpi: detected a 16-level brightness capable ThinkPad
Sep 20 07:40:08 xubuntu kernel: [ 108.724898] thinkpad_acpi: radio switch found; radios are enabled
Sep 20 07:40:08 xubuntu kernel: [ 108.724905] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
Sep 20 07:40:08 xubuntu kernel: [ 108.724914] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
Sep 20 07:40:08 xubuntu kernel: [ 108.724916] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
Sep 20 07:40:08 xubuntu kernel: [ 108.725641] thinkpad_acpi: asked for hotkey mask 0x078c7fff, but firmware forced it to 0x008c7fff
Sep 20 07:40:08 xubuntu kernel: [ 108.730634] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
Sep 20 07:40:08 xubuntu kernel: [ 108.739990] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
Sep 20 07:40:08 xubuntu kernel: [ 108.740775] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
Sep 20 07:40:08 xubuntu kernel: [ 108.745716] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input17
Sep 20 07:40:10 xubuntu kernel: [ 110.146712] iwlwifi 0000:05:00.0: loaded firmware version 39.31.5.1 build 35138 op_mode iwldvm
Sep 20 07:40:10 xubuntu kernel: [ 110.157516] kvm: disabled by bios
Donne le nom complet de ton pc (pour les portables, le nom complet est écrit ou gravé en-dessous).
La Doc du site indique quelques réglages spécifiques pour les thinkpads.
- -
Mais le principal point à régler est d'ordre graphique :
Sep 20 07:39:49 xubuntu kernel: [ 8.476652] radeon 0000:01:00.0: registered panic notifier
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#30 Le 22/09/2017, à 19:49
- fwehrli
Re : {résolu}Bug complet xubuntu
Lenovo thinkpad type 2847-d8g s/n Lr-1l2kx 11/07
Product id:2847d8g
Product key: 4gy3g-r2q7x-7dgxv-jqkv7-kvfrrr
Je ne vois rien d'autre en dessous
Devant c'est ecrit sl510
Intel core 2 duo
Hors ligne
#31 Le 22/09/2017, à 19:51
- fwehrli
Re : {résolu}Bug complet xubuntu
J'irai dans me bios demain matin et je ferai à nouveau un smartctl sans numero à nouveau en live
Actuellement je l'utilise sous windows 7 ça marche étonnamment bien
Hors ligne
#32 Le 22/09/2017, à 20:17
- moko138
Re : {résolu}Bug complet xubuntu
Ton Lenovo thinkpad 2847-d8g ne figure pas dans la page de la Doc liste_portables_thinkpad.
Pour la question principale, graphique, montre le retour, en session live, de
lspci -nnk | grep -Ei -A 4 "VGA|3D|Display"
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#33 Le 22/09/2017, à 20:23
- moko138
Re : {résolu}Bug complet xubuntu
Par contre, sous le nom incomplet de "Lenovo Thinkpad SL510", il en est dit sur la même page
Wifi OK, Bluetooth OK, webcam OK, boutons de gestion du son OK. Tout fonctionne à merveille. Par contre je n'ai pas encore pu tester le lecteur CARD EXPRESS
Lucid 10.04
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#34 Le 22/09/2017, à 21:33
- nam1962
Re : {résolu}Bug complet xubuntu
Depuis, il y a eu des progrès côté pilotes !
Maintenant, on est peut-être dans du legacy à cet âge !
[ Modéré ]
Hors ligne
#35 Le 22/09/2017, à 21:49
- fwehrli
Re : {résolu}Bug complet xubuntu
Désolé moko mais je ne comprends pas le #33
Hors ligne
#36 Le 22/09/2017, à 22:00
- nam1962
Re : {résolu}Bug complet xubuntu
...moko a cité la doc, puis s'est rendu compte que ça datait de lucid, c'est à dire d'il y a 7 ans.
Maintenant, un ordi qui a 7 ans ou plus, quoiqu' utilisable, peut avoir des soucis d'obsolescence (auxquels on trouvera forcément une réponse dans le monde Linux)
Dernière modification par nam1962 (Le 22/09/2017, à 22:01)
[ Modéré ]
Hors ligne
#37 Le 23/09/2017, à 09:32
- fwehrli
Re : {résolu}Bug complet xubuntu
Je suis dans le bios, je ne trouve pas de menu avec ACPI
En attendant j'ai lancé un test du disque dur à partir du bios
Hors ligne
#38 Le 23/09/2017, à 10:00
- moko138
Re : {résolu}Bug complet xubuntu
Le #33 dit simplement que le "Lenovo Thinkpad SL510" était parfaitement pris en charge par *buntu 10.04.
Tout ce qui fonctionne sur les anciennes versions est encore pris en charge par les versions actuelles... sauf certaines cartes graphiques.
À ce propos, tu as oublié de répondre au #32.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#39 Le 23/09/2017, à 10:03
- moko138
Re : {résolu}Bug complet xubuntu
...moko a cité la doc, puis s'est rendu compte que (...)
Pas du tout.
Merci de ne pas déformer mes propos ni ma pensée.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#40 Le 23/09/2017, à 10:04
- fwehrli
Re : {résolu}Bug complet xubuntu
Je suis toujours au scan du disque, à ce rythme j'en ai pour la matinée.
Dès que ce sera fini je ferai le #32
Hors ligne
#41 Le 23/09/2017, à 11:12
- fwehrli
Re : {résolu}Bug complet xubuntu
Voici le résultat de smartctl sans mettre de numéro après sda:
sudo smartctl -s on -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-32-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-08A23T1
Serial Number: WD-WX11A41D3382
LU WWN Device Id: 5 0014ee 65689137a
Firmware Version: 02.01A02
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Sep 23 09:10:46 2017 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 77) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 144 132 021 Pre-fail Always - 1766
4 Start_Stop_Count 0x0032 058 058 000 Old_age Always - 42373
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5322
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3101
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 45
193 Load_Cycle_Count 0x0032 015 015 000 Old_age Always - 555388
194 Temperature_Celsius 0x0022 083 073 000 Old_age Always - 60
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 094 094 000 Old_age Always - 4808
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1194 -
# 2 Short offline Completed without error 00% 1034 -
# 3 Short offline Completed without error 00% 947 -
# 4 Short offline Completed without error 00% 921 -
# 5 Short offline Completed without error 00% 920 -
# 6 Short offline Completed without error 00% 855 -
# 7 Short offline Completed without error 00% 753 -
# 8 Short offline Completed without error 00% 576 -
# 9 Short offline Aborted by host 10% 483 -
#10 Short offline Completed without error 00% 441 -
#11 Short offline Completed without error 00% 368 -
#12 Short offline Completed without error 00% 292 -
#13 Short offline Completed without error 00% 277 -
#14 Short offline Completed without error 00% 234 -
#15 Short offline Completed without error 00% 208 -
#16 Short offline Completed without error 00% 167 -
#17 Short offline Completed without error 00% 150 -
#18 Short offline Completed without error 00% 108 -
#19 Short offline Completed without error 00% 81 -
#20 Short offline Completed without error 00% 7 -
#21 Vendor (0x50) Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Hors ligne
#42 Le 23/09/2017, à 11:14
- fwehrli
Re : {résolu}Bug complet xubuntu
Résultat de lspci:
xubuntu@xubuntu:~$ lspci -nnk | grep -Ei -A 4 "VGA|3D|Display"
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV710/M92 [Mobility Radeon HD 4530/4570/545v] [1002:9553]
Subsystem: Lenovo Device [17aa:2129]
Kernel driver in use: radeon
01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] RV710/730 HDMI Audio [Radeon HD 4000 series] [1002:aa38]
Subsystem: Lenovo Device [17aa:2129]
xubuntu@xubuntu:~$
Hors ligne
#43 Le 23/09/2017, à 11:15
- fwehrli
Re : {résolu}Bug complet xubuntu
Je n'ai ren trouvé dans le bios en ce qui concerne de l'acpi.
Après le scan du du disque dur à partir du bios, je n'ai eu aucun rapport. Du coup j'ai l'impression d'avoir perdu 2heures.
Hors ligne
#44 Le 23/09/2017, à 11:38
- moko138
Re : {résolu}Bug complet xubuntu
Ben oui : smartctl est beaucoup plus précis...
- -
194 Temperature_Celsius 0x0022 083 073 000 60
60°C pour un disque dur, c'est monstrueux !
Ça nuit aux performances et ça l'abîme !
Donc
1) ferme déjà tout ce qui est image et video.
2) Puis dépêche-toi de faire
sudo apt-get update && sudo apt-get install -y hdparm hddtemp
3) Ensuite, puisque tu as un Western Digital Scorpio Blue, montre le retour complet de :
sudo hddtemp /dev/sda; echo; sudo hdparm -B 250 /dev/sda
4) puis ne touche à rien pendant dix minutes.
5) À ce moment-là tu redonneras
sudo hddtemp /dev/sda
Edit : fautes de frappe.
Dernière modification par moko138 (Le 23/09/2017, à 11:39)
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#45 Le 23/09/2017, à 11:53
- fwehrli
Re : {résolu}Bug complet xubuntu
premier résultat:
xubuntu@xubuntu:~$ sudo hddtemp /dev/sda; echo; sudo hdparm -B 250 /dev/sda
/dev/sda: WDC WD3200BEVT-08A23T1: 69°C
/dev/sda:
setting Advanced Power Management level to 0xfa (250)
APM_level = 250
xubuntu@xubuntu:~$
La suite dans 10 minutes. Je n'avais rien d'ouvert à part la page du forum ubuntu.
Hors ligne
#46 Le 23/09/2017, à 12:09
- fwehrli
Re : {résolu}Bug complet xubuntu
résultat:
xubuntu@xubuntu:~$ sudo hddtemp /dev/sda
/dev/sda: WDC WD3200BEVT-08A23T1: 64°C
xubuntu@xubuntu:~$
Hors ligne
#47 Le 23/09/2017, à 12:46
- moko138
Re : {résolu}Bug complet xubuntu
fais
sudo hdparm -B 246 /dev/sda
et cinq minutes après (sans video ni photo ni grosse activité) montre
sudo hddtemp /dev/sda
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#48 Le 23/09/2017, à 12:57
- moko138
Re : {résolu}Bug complet xubuntu
1) En général, par souci de compacité, les fabricants sous-dimensionnent les plots ou pattes de la face inférieure :
pour un bon renouvellement de l'air, n'hésite pas à glisser 2-3 objets genre gommes ou gros feutres d'au moins 10-15 mm entre la table et le portable.
- -
2) Au bout de "2 ans et demi", un bon dépoussiérage ne fait pas de mal à un portable (et même à une tour).
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#49 Le 23/09/2017, à 12:57
- fwehrli
Re : {résolu}Bug complet xubuntu
Je viens d'essayer en mode invité
Mes logiciels se lancent.
Il y a donc un probleme avec ma session habituelle
Hors ligne
#50 Le 23/09/2017, à 13:01
- moko138
Re : {résolu}Bug complet xubuntu
En redémarrant, tu as stoppé le réglage par hdparm,
et en session invité tu ne peux rien installer.
Donc ton disque recommence à chauffer.
Et tu n'as même pas fait le #47.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne