Ubuntu-fr

none

carte mémoire sd

Bonjour à toutes et à tous,

J'ai un appareil photo Kyocera Finecam L3:

http://www.kyocera-europe.com/Finecam%20L3.php
http://www.achetezfacile.com/kyocera-finecam-l3-comparer-les-prix-71876.html

J'utilise une carte SD 256 Mo de marque KINGMAX:

http://www.kingmaxdigi.com/product/SD.htm

Cette carte n'est pas reconnue par Ubuntu, alors que la carte mémoire d'origine, une Panasonic SD 16 Mo l'est parfaitement...

http://www.panasonic.fr/servlet/PB/menu/1109654_l3/index.html
(page du modèle 32 Mo)

Alors que je formatte mes cartes SD avec mon appareil photo de la même façon, pourquoi l'une d'elle est-elle reconnue et pas l'autre?

Dans l'attente de réponses de votre part, je me tiens à votre disposition pour de plus amples renseignements (dmesg, lsusb, etc.)

Cordialement

cy

none

Re : carte mémoire sd

Ci-joint:

LINUX

marwan@cy-buntu:~$ uname -a
Linux cy-buntu 2.6.12-10-386 #1 Fri Nov 18 11:51:02 UTC 2005 i686 GNU/Linux

CARTE DEFECTUEUSE KINGMAX 256 MO

lsusb

marwan@cy-buntu:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 007: ID 0482:0105 Kyocera Corp.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

dmesg

[4295973.003000] scsi1 (0:0): rejecting I/O to dead device
[4295973.003000] FAT: Directory bread(block 38) failed
[4295997.437000] usb 2-1: new full speed USB device using uhci_hcd and address 4
[4295997.627000] usb-storage: This device (0482,0105,0100 S 06 P 50) has unneede d SubClass and Protocol entries in unusual_devs.h
[4295997.627000]    Please send a copy of this message to <linux-usb-devel@lists .sourceforge.net>
[4295997.629000] scsi2 : SCSI emulation for USB Mass Storage devices
[4295997.634000] usb-storage: device found at 4
[4295997.634000] usb-storage: waiting for device to settle before scanning
[4296002.634000]   Vendor: Kyocera   Model: Finecam L3        Rev: 0100
[4296002.634000]   Type:   Direct-Access                      ANSI SCSI revision : 02
[4296002.650000] SCSI device sda: 29120 512-byte hdwr sectors (15 MB)
[4296002.655000] sda: Write Protect is off
[4296002.656000] sda: Mode Sense: 0b 00 00 08
[4296002.656000] sda: assuming drive cache: write through
[4296002.672000] SCSI device sda: 29120 512-byte hdwr sectors (15 MB)
[4296002.677000] sda: Write Protect is off
[4296002.678000] sda: Mode Sense: 0b 00 00 08
[4296002.678000] sda: assuming drive cache: write through
[4296002.678000]  /dev/scsi/host2/bus0/target0/lun0: p1
[4296002.722000] Attached scsi removable disk sda at scsi2, channel 0, id 0, lun  0
[4296002.727000] usb-storage: device scan complete
[4296007.079000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[4296035.271000] usb 2-1: USB disconnect, address 4
[4296233.187000] usb 2-1: new full speed USB device using uhci_hcd and address 5
[4296233.326000] usb-storage: This device (0482,0105,0100 S 06 P 50) has unneede d SubClass and Protocol entries in unusual_devs.h
[4296233.326000]    Please send a copy of this message to <linux-usb-devel@lists .sourceforge.net>
[4296233.328000] scsi3 : SCSI emulation for USB Mass Storage devices
[4296233.333000] usb-storage: device found at 5
[4296233.333000] usb-storage: waiting for device to settle before scanning
[4296236.771000] usb 2-1: USB disconnect, address 5
[4296246.687000] usb 2-1: new full speed USB device using uhci_hcd and address 6
[4296246.826000] usb-storage: This device (0482,0105,0100 S 06 P 50) has unneede d SubClass and Protocol entries in unusual_devs.h
[4296246.826000]    Please send a copy of this message to <linux-usb-devel@lists .sourceforge.net>
[4296246.828000] scsi4 : SCSI emulation for USB Mass Storage devices
[4296246.833000] usb-storage: device found at 6
[4296246.833000] usb-storage: waiting for device to settle before scanning
[4296251.833000]   Vendor: Kyocera   Model: Finecam L3        Rev: 0100
[4296251.833000]   Type:   Direct-Access                      ANSI SCSI revision : 02
[4296251.848000] SCSI device sda: 499712 512-byte hdwr sectors (256 MB)
[4296251.853000] sda: Write Protect is off
[4296251.854000] sda: Mode Sense: 0b 00 00 08
[4296251.854000] sda: assuming drive cache: write through
[4296251.869000] SCSI device sda: 499712 512-byte hdwr sectors (256 MB)
[4296251.874000] sda: Write Protect is off
[4296251.874000] sda: Mode Sense: 0b 00 00 08
[4296251.875000] sda: assuming drive cache: write through
[4296251.875000]  /dev/scsi/host4/bus0/target0/lun0: p1
[4296251.920000] Attached scsi removable disk sda at scsi4, channel 0, id 0, lun  0
[4296251.924000] usb-storage: device scan complete
[4296286.113000] SCSI error : <4 0 0 0> return code = 0x8000002
[4296286.113000] sda: Current: sense key: Medium Error
[4296286.113000]     Additional sense: Unrecovered read error
[4296286.113000] end_request: I/O error, dev sda, sector 499704
[4296286.113000] Buffer I/O error on device sda1, logical block 62459
[4296319.319000] SCSI error : <4 0 0 0> return code = 0x8000002
[4296319.319000] sda: Current: sense key: Medium Error
[4296319.319000]     Additional sense: Unrecovered read error
[4296319.319000] end_request: I/O error, dev sda, sector 499704
[4296319.319000] Buffer I/O error on device sda1, logical block 62459
[4297152.515000] sda : READ CAPACITY failed.
[4297152.515000] sda : status=0, message=00, host=7, driver=00
[4297152.515000] sda : sense not available.
[4297152.521000] usb 2-1: USB disconnect, address 6
[4297152.569000] sda: Write Protect is off
[4297152.569000] sda: Mode Sense: 00 00 00 00
[4297152.569000] sda: assuming drive cache: write through
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] sda : READ CAPACITY failed.
[4297152.569000] sda : status=0, message=00, host=0, driver=04
[4297152.569000] sda : sense not available.
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] sda: Write Protect is off
[4297152.569000] sda: Mode Sense: 00 00 00 00
[4297152.569000] sda: assuming drive cache: write through
[4297152.569000]  /dev/scsi/host4/bus0/target0/lun0:<3>scsi4 (0:0): rejecting I/ O to dead device
[4297152.569000] Buffer I/O error on device sda, logical block 0
[4297152.569000] scsi4 (0:0): rejecting I/O to dead device
[4297152.569000] Buffer I/O error on device sda, logical block 0
[4297152.570000]  unable to read partition table
[4297757.437000] usb 2-1: new full speed USB device using uhci_hcd and address 7
[4297757.628000] usb-storage: This device (0482,0105,0100 S 06 P 50) has unneede d SubClass and Protocol entries in unusual_devs.h
[4297757.628000]    Please send a copy of this message to <linux-usb-devel@lists .sourceforge.net>
[4297757.629000] scsi5 : SCSI emulation for USB Mass Storage devices
[4297757.634000] usb-storage: device found at 7
[4297757.634000] usb-storage: waiting for device to settle before scanning
[4297762.634000]   Vendor: Kyocera   Model: Finecam L3        Rev: 0100
[4297762.634000]   Type:   Direct-Access                      ANSI SCSI revision : 02
[4297762.649000] SCSI device sda: 499712 512-byte hdwr sectors (256 MB)
[4297762.654000] sda: Write Protect is off
[4297762.655000] sda: Mode Sense: 0b 00 00 08
[4297762.655000] sda: assuming drive cache: write through
[4297762.671000] SCSI device sda: 499712 512-byte hdwr sectors (256 MB)
[4297762.676000] sda: Write Protect is off
[4297762.676000] sda: Mode Sense: 0b 00 00 08
[4297762.677000] sda: assuming drive cache: write through
[4297762.677000]  /dev/scsi/host5/bus0/target0/lun0: p1
[4297762.724000] Attached scsi removable disk sda at scsi5, channel 0, id 0, lun  0
[4297762.736000] usb-storage: device scan complete
[4297797.021000] SCSI error : <5 0 0 0> return code = 0x8000002
[4297797.021000] sda: Current: sense key: Medium Error
[4297797.021000]     Additional sense: Unrecovered read error
[4297797.021000] end_request: I/O error, dev sda, sector 499704
[4297797.021000] Buffer I/O error on device sda1, logical block 62459
[4297830.223000] SCSI error : <5 0 0 0> return code = 0x8000002
[4297830.224000] sda: Current: sense key: Medium Error
[4297830.224000]     Additional sense: Unrecovered read error
[4297830.224000] end_request: I/O error, dev sda, sector 499704
[4297830.224000] Buffer I/O error on device sda1, logical block 62459
marwan@cy-buntu:~$

CARTE EN ETAT DE FONCTIONNEMENT PANASONIC 16 MO

lsusb

marwan@cy-buntu:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 008: ID 0482:0105 Kyocera Corp.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

dmesg

[4297905.687000] usb 2-1: new full speed USB device using uhci_hcd and address 8
[4297905.829000] usb-storage: This device (0482,0105,0100 S 06 P 50) has unneede d SubClass and Protocol entries in unusual_devs.h
[4297905.829000]    Please send a copy of this message to <linux-usb-devel@lists .sourceforge.net>
[4297905.830000] scsi6 : SCSI emulation for USB Mass Storage devices
[4297905.835000] usb-storage: device found at 8
[4297905.835000] usb-storage: waiting for device to settle before scanning
[4297910.835000]   Vendor: Kyocera   Model: Finecam L3        Rev: 0100
[4297910.835000]   Type:   Direct-Access                      ANSI SCSI revision : 02
[4297910.858000] SCSI device sda: 29120 512-byte hdwr sectors (15 MB)
[4297910.862000] sda: Write Protect is off
[4297910.863000] sda: Mode Sense: 0b 00 00 08
[4297910.863000] sda: assuming drive cache: write through
[4297910.881000] SCSI device sda: 29120 512-byte hdwr sectors (15 MB)
[4297910.886000] sda: Write Protect is off
[4297910.887000] sda: Mode Sense: 0b 00 00 08
[4297910.887000] sda: assuming drive cache: write through
[4297910.887000]  /dev/scsi/host6/bus0/target0/lun0: p1
[4297910.934000] Attached scsi removable disk sda at scsi6, channel 0, id 0, lun  0
[4297910.939000] usb-storage: device scan complete
[4297915.512000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
marwan@cy-buntu:~$

docteur_marc

Re : carte mémoire sd

ne formate pas sur ton appareille photo  toujours sur le pc ..

none

Re : carte mémoire sd

Oki... mais:

1- Comment puis-je formater à partir du PC une carte qui n'est pas reconnue?

>> Comment faire ré-apparaître cette carte SD 256 Mo?

2- Pourquoi les deux cartes formatées à partir de l'APN ne marchent-elles pas toutes les deux?

merci!

cy