Pages : 1
#1 Le 16/05/2008, à 18:50
- mamat00
[Résolu] - ubuntu + windows avec du raid 0
Bonjour, après avoir installé ubuntu sur un disque ide je ne peu plus accéder à windows qui est installé sur 2 disques sata en raid0.
J ai parcouru bcp de forum avec divers solution mais surement pas tjrs bien appliqué :
-fixmbr et fixboot n ont pas fonctionner
-divers utilitaires comme partition doctor, de meme
-réinstall d un windows a la place de linux pr modifier le boot.ini, non plus
-...
Je suis passé par les messages "invalid partition error" et l erreur type d'une install windows apres celle de linux
Pour installer windows XP sur la partition sélectionnée, le programme
d'installation doit copier certains fichiers de démarrage sur le disk 0
de *** Mo ayant l'ID 0 sur atapi [MBR]. Cependant, ce disque ne contient pas de partition compatible avec windows XP
Créer une partition compatible avec windows XP sur le disque ci-dessus
Avec mon impatience et mon noobisme j ai du completement modifier les types, flag, taille des partitions. Là je viens d installer dmraid et le raid0 est enfin reconnu mais pas accessible.
voilà le chantier :
Warning: invalid flag 0x0000 of partition table 5 will be corrected by w(rite)
Disk /dev/sda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xffffffff
Device Boot Start End Blocks Id System
/dev/sda1 2 1305 10474380 f W95 Ext'd (LBA)
/dev/sda2 1306 29186 223954132+ 17 Hidden HPFS/NTFS
Disk /dev/sdb: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x080807ab
Disk /dev/sdb doesn't contain a valid partition table
Disk /dev/sdc: 61.4 GB, 61492838400 bytes
255 heads, 63 sectors/track, 7476 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x8f028f02
Device Boot Start End Blocks Id System
/dev/sdc1 * 1 389 3124611 83 Linux
/dev/sdc2 390 7475 56918295 f W95 Ext'd (LBA)
/dev/sdc5 523 4443 31495401 7 HPFS/NTFS
/dev/sdc6 4444 7475 24354508+ 7 HPFS/NTFS
/dev/sdc7 390 522 1068259+ 82 Linux swap / Solaris
Partition table entries are not in disk order
Disk /dev/dm-0: 240.0 GB, 240068198400 bytes
255 heads, 63 sectors/track, 29186 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xffffffff
Device Boot Start End Blocks Id System
/dev/dm-0p1 2 1305 10474380 f W95 Ext'd (LBA)
/dev/dm-0p2 1306 29186 223954132+ 17 Hidden HPFS/NTFS
/dev/dm-0p5 2 1305 10474348+ 7 HPFS/NTFS
Disk /dev/dm-1: 229.3 GB, 229329031680 bytes
255 heads, 63 sectors/track, 27881 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x69205244
This doesn't look like a partition table
Probably you selected the wrong device.
Device Boot Start End Blocks Id System
/dev/dm-1p1 ? 13578 119522 850995205 72 Unknown
Partition 1 does not end on cylinder boundary.
/dev/dm-1p2 ? 45382 79243 271987362 74 Unknown
Partition 2 does not end on cylinder boundary.
/dev/dm-1p3 ? 10499 10499 0 65 Novell Netware 386
Partition 3 does not end on cylinder boundary.
/dev/dm-1p4 167628 167631 25817+ 0 Empty
Partition 4 does not end on cylinder boundary.
Partition table entries are not in disk order
Disk /dev/dm-2: 10.7 GB, 10725732864 bytes
255 heads, 63 sectors/track, 1303 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x69205244
This doesn't look like a partition table
Probably you selected the wrong device.
Device Boot Start End Blocks Id System
/dev/dm-2p1 ? 13578 119522 850995205 72 Unknown
Partition 1 does not end on cylinder boundary.
/dev/dm-2p2 ? 45382 79243 271987362 74 Unknown
Partition 2 does not end on cylinder boundary.
/dev/dm-2p3 ? 10499 10499 0 65 Novell Netware 386
Partition 3 does not end on cylinder boundary.
/dev/dm-2p4 167628 167631 25817+ 0 Empty
Partition 4 does not end on cylinder boundary.
Partition table entries are not in disk order
Comme vs pouvez le voir, c'est le bordel
Je souhaiterais ne pas modifier le raid0 mais si besoin je peu completement formater le disque ide pr pouvoir booter sur windows afin de recup mes données.
#2 Le 16/05/2008, à 19:37
- mamat00
Re : [Résolu] - ubuntu + windows avec du raid 0
je precise que je n ai que 3 disque : ide 60go et 2xsata120 en raid0 avec le controlleur nvidia
windows est sur /dev/dm-2, comment faire pr que grub reconnaisse cette partition et puisse booté dessus ?
#3 Le 17/05/2008, à 01:17
- mamat00
Re : [Résolu] - ubuntu + windows avec du raid 0
up
#4 Le 17/05/2008, à 03:05
- mamat00
Re : [Résolu] - ubuntu + windows avec du raid 0
résolu, merci moi
#5 Le 17/05/2008, à 09:39
- Jamo 707i
Re : [Résolu] - ubuntu + windows avec du raid 0
Bonjour
peut tu donner ta soluce pour les autres newbee comme moi ,svp?
Hors ligne