[EN COURS] Installation webcam HERCULES CLASSIC LINK

nils2rs · Le 13/10/2008, à 21:06

Bonsoir,

Je suis débutant avec Ubuntu 8.04 - Hardy Heron. J'essaye d'installer ma webcam qui est une Hercules Classic Link (sur un portable HP530).

J'ai suivi méticuleusement le tutoriel suivant : http://doc.ubuntu-fr.org/trust_320

Et regardé dans celui-ci si je ne pouvais pas trouver de solution : http://forum.ubuntu-fr.org/viewtopic.php?id=231042&p=1

Ne trouvant pas me voici :

En suivant le tutoriel ci dessus, aucun problème lors de l'installation. Toutes les vérifications qui terminent les étapes décrites fonctionnent. En revanche, je suis sceptique quant au résultat de la commande du test :

dmesg

qui me renvoie ceci :

[ 834.165551] usb 1-2: new full speed USB device using uhci_hcd and address 5
[ 834.401255] usb 1-2: configuration #1 chosen from 1 choice
[ 2619.514880] usb 1-2: USB disconnect, address 5
[ 2626.520523] usb 1-2: new full speed USB device using uhci_hcd and address 6
[ 2626.756221] usb 1-2: configuration #1 chosen from 1 choice

Lorsque je lance camorama, j'obtient le message suivant :

Erreur (camorama)
Could not connect to video device (/dev/video0). Please check connection.

J'aimerai beaucoup pouvoir faire fonctionner ma webcam pour discuter sur aMsn. Si vous pouvez m'aider ca serait simpa de votre part. Merci d'avance

herberts · Le 13/10/2008, à 21:40

peut tu me donner le retour de

lsusb

(quand la webcam est branchée) et le retour de

cat /etc/modules

nils2rs · Le 13/10/2008, à 21:49

lsusb :

Bus 002 Device 001: ID 0000:0000
Bus 001 Device 006: ID 06f8:3009 Guillemot Corp.
Bus 001 Device 001: ID 0000:0000

cat /etc/modules

cat: /etc/modules/: N'est pas un dossier

J'ai donc fait : more /etc/modules

il me renvoie :

root@Laptop:~# more /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
fuse
lp
ov51x-jpeg force_palette=4

Merci de m'aider

nils2rs · Le 13/10/2008, à 21:50

edit : cat /etc/modules fonctionne, c'est le "/" qui était en trop :

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
fuse
lp
ov51x-jpeg force_palette=4

herberts · Le 13/10/2008, à 22:09

Bon, ça c'est ok. Il me semble que j'avais eu des soucis avec camorama également. Tu as rebooté depuis que tu as fait les manips ? ou chargé les modules à la main avec "modprobe" ?

nils2rs · Le 13/10/2008, à 22:11

Le problème est le même sur vlc, et aMsn ne détecte pas de webcam non plus

J'ai rédémarré à deux reprises et chargé plusieurs fois le module (vérifié aussi qu'il était bien chargé => a priori il l'est)

HELP

herberts · Le 13/10/2008, à 22:14

ok, donc, essaye de débrancher/rebrancher ta webcam, tu attends 15 secondes, tu la redébranche/rerebranche, et tu donne le retour de

lsusb

Chez moi par exemple, je la branche, elle n'est pas reconnue, je la débranche/rebranche, elle marche. Je pourrais pas t'expliquer pourquoi par contre.

nils2rs · Le 13/10/2008, à 22:17

lsusb :

Bus 002 Device 001: ID 0000:0000
Bus 001 Device 007: ID 06f8:3009 Guillemot Corp.
Bus 001 Device 001: ID 0000:0000

Pas de changement...

herberts · Le 13/10/2008, à 22:17

excuse moi, de

dmesg

je voulais dire , mais je veux bien

lsusb

quand même

nils2rs · Le 13/10/2008, à 22:19

[ 8.754718] Total of 2 processors activated (9314.99 BogoMIPS).
[ 8.754910] ENABLING IO-APIC IRQs
[ 8.755097] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 8.901996] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 8.921969] Brought up 2 CPUs
[ 8.921992] CPU0 attaching sched-domain:
[ 8.921994] domain 0: span 03
[ 8.921996] groups: 01 02
[ 8.921998] CPU1 attaching sched-domain:
[ 8.921999] domain 0: span 03
[ 8.922001] groups: 02 01
[ 8.922203] net_namespace: 64 bytes
[ 8.922210] Booting paravirtualized kernel on bare hardware
[ 8.922570] Time: 18:19:57 Date: 10/13/08
[ 8.922595] NET: Registered protocol family 16
[ 8.922763] EISA bus registered
[ 8.922767] ACPI: bus type pci registered
[ 8.923966] PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=16
[ 8.923967] PCI: Using configuration type 1
[ 8.923979] Setting up standard PCI resources
[ 8.925545] ACPI: EC: Look up EC in DSDT
[ 8.926550] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 8.945831] ACPI: Interpreter enabled
[ 8.945834] ACPI: (supports S0 S3 S4 S5)
[ 8.945843] ACPI: Using IOAPIC for interrupt routing
[ 8.951115] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 8.951117] ACPI: EC: driver started in interrupt mode
[ 8.951160] ACPI: PCI Root Bridge [C002] (0000:00)
[ 8.951710] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 8.951714] PCI quirk: region 1100-113f claimed by ICH6 GPIO
[ 8.952447] PCI: Transparent bridge - 0000:00:1e.0
[ 8.952523] ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
[ 8.952737] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C098._PRT]
[ 8.952854] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C100._PRT]
[ 8.952951] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C110._PRT]
[ 8.965326] ACPI: PCI Interrupt Link [C10C] (IRQs *10 11)
[ 8.965474] ACPI: PCI Interrupt Link [C10D] (IRQs *10 11)
[ 8.965619] ACPI: PCI Interrupt Link [C10E] (IRQs 10 *11)
[ 8.965758] ACPI: PCI Interrupt Link [C10F] (IRQs 10 11) *0, disabled.
[ 8.965907] ACPI: PCI Interrupt Link [C11C] (IRQs 10 11) *5
[ 8.966053] ACPI: PCI Interrupt Link [C11D] (IRQs *10 11)
[ 8.966193] ACPI: PCI Interrupt Link [C11E] (IRQs 10 11) *0, disabled.
[ 8.966263] ACPI Exception (pci_link-0184): AE_NOT_FOUND, Evaluating _PRS [20070126]
[ 8.966397] ACPI: Power Resource [C1FE] (on)
[ 8.966431] ACPI: Power Resource [C206] (on)
[ 8.966504] ACPI: Power Resource [C2EE] (off)
[ 8.966573] ACPI: Power Resource [C2EF] (off)
[ 8.966641] ACPI: Power Resource [C2F0] (off)
[ 8.966709] ACPI: Power Resource [C2F1] (off)
[ 8.966750] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 8.966775] pnp: PnP ACPI init
[ 8.966781] ACPI: bus type pnp registered
[ 8.971603] pnp: PnP ACPI: found 12 devices
[ 8.971605] ACPI: ACPI bus type pnp unregistered
[ 8.971609] PnPBIOS: Disabled by ACPI PNP
[ 8.971800] PCI: Using ACPI for IRQ routing
[ 8.971802] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 9.053574] NET: Registered protocol family 8
[ 9.053576] NET: Registered protocol family 20
[ 9.053604] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 9.053608] hpet0: 3 64-bit timers, 14318180 Hz
[ 9.054639] AppArmor: AppArmor Filesystem Enabled
[ 9.057560] Time: tsc clocksource has been installed.
[ 9.057573] Switched to high resolution mode on CPU 0
[ 9.057667] Switched to high resolution mode on CPU 1
[ 9.073519] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 9.073522] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 9.073525] system 00:00: iomem range 0x100000-0x7f7fffff could not be reserved
[ 9.073533] system 00:09: ioport range 0x500-0x57f has been reserved
[ 9.073535] system 00:09: ioport range 0x800-0x80f has been reserved
[ 9.073538] system 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 9.073540] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[ 9.073544] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 9.073546] system 00:0a: ioport range 0x1000-0x107f has been reserved
[ 9.073549] system 00:0a: ioport range 0x1100-0x113f has been reserved
[ 9.073551] system 00:0a: ioport range 0x1200-0x121f has been reserved
[ 9.073553] system 00:0a: iomem range 0xf8000000-0xfbffffff has been reserved
[ 9.073555] system 00:0a: iomem range 0xfec00000-0xfec000ff could not be reserved
[ 9.073558] system 00:0a: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 9.073560] system 00:0a: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 9.073562] system 00:0a: iomem range 0xfed90000-0xfed9afff could not be reserved
[ 9.073567] system 00:0b: iomem range 0xfeda0000-0xfedbffff could not be reserved
[ 9.073569] system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 9.103870] PCI: Bridge: 0000:00:1c.0
[ 9.103872] IO window: disabled.
[ 9.103877] MEM window: disabled.
[ 9.103881] PREFETCH window: disabled.
[ 9.103886] PCI: Bridge: 0000:00:1c.1
[ 9.103887] IO window: disabled.
[ 9.103892] MEM window: f0000000-f00fffff
[ 9.103896] PREFETCH window: disabled.
[ 9.103904] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[ 9.103905] IO window: 00002400-000024ff
[ 9.103910] IO window: 00002800-000028ff
[ 9.103915] PREFETCH window: 80000000-83ffffff
[ 9.103919] MEM window: 84000000-87ffffff
[ 9.103924] PCI: Bridge: 0000:00:1e.0
[ 9.103927] IO window: 2000-2fff
[ 9.103932] MEM window: f0100000-f03fffff
[ 9.103935] PREFETCH window: disabled.
[ 9.103963] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 9.103970] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 9.103992] ACPI: PCI Interrupt 0000:00:1c.1[b] -> GSI 17 (level, low) -> IRQ 17
[ 9.103997] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 9.104009] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 9.104025] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 9.104037] NET: Registered protocol family 2
[ 9.150370] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 9.150540] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 9.151106] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 9.151381] TCP: Hash tables configured (established 131072 bind 65536)
[ 9.151383] TCP reno registered
[ 9.162418] checking if image is initramfs... it is
[ 9.704860] Freeing initrd memory: 7704k freed
[ 9.705599] audit: initializing netlink socket (disabled)
[ 9.705610] audit(1223921997.297:1): initialized
[ 9.705805] highmem bounce pool size: 64 pages
[ 9.707412] VFS: Disk quotas dquot_6.5.1
[ 9.707472] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.707582] io scheduler noop registered
[ 9.707583] io scheduler anticipatory registered
[ 9.707585] io scheduler deadline registered
[ 9.707593] io scheduler cfq registered (default)
[ 9.707604] Boot video device is 0000:00:02.0
[ 9.707649] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[ 9.707739] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 9.707792] assign_interrupt_mode Found MSI capability
[ 9.707837] Allocate Port Service[0000:00:1c.0:pcie00]
[ 9.707867] Allocate Port Service[0000:00:1c.0:pcie02]
[ 9.707955] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 9.708008] assign_interrupt_mode Found MSI capability
[ 9.708050] Allocate Port Service[0000:00:1c.1:pcie00]
[ 9.708079] Allocate Port Service[0000:00:1c.1:pcie02]
[ 9.708301] isapnp: Scanning for PnP cards...
[ 10.061694] isapnp: No Plug & Play device found
[ 10.083626] Real Time Clock Driver v1.12ac
[ 10.083832] hpet_resources: 0xfed00000 is busy
[ 10.083875] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 10.084885] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.084940] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 10.085022] PNP: PS/2 Controller [PNP0303:C1FB,PNP0f13:C1FC] at 0x60,0x64 irq 1,12
[ 10.086820] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 10.087570] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.087573] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 10.087576] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 10.087578] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 10.087580] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 10.111342] mice: PS/2 mouse device common for all mice
[ 10.111433] EISA: Probing bus 0 at eisa.0
[ 10.111439] Cannot allocate resource for EISA slot 1
[ 10.111442] Cannot allocate resource for EISA slot 2
[ 10.111444] Cannot allocate resource for EISA slot 3
[ 10.111464] EISA: Detected 0 cards.
[ 10.111466] cpuidle: using governor ladder
[ 10.111468] cpuidle: using governor menu
[ 10.111543] NET: Registered protocol family 1
[ 10.111565] Using IPI No-Shortcut mode
[ 10.111589] registered taskstats version 1
[ 10.111666] Magic number: 12:182:342
[ 10.111748] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 10.111750] EDD information not available.
[ 10.111919] Freeing unused kernel memory: 368k freed
[ 10.133089] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 11.284647] fuse init (API version 7.9)
[ 11.295345] ACPI: Transitioning device [C2F2] to D3
[ 11.295347] ACPI: Transitioning device [C2F2] to D3
[ 11.295350] ACPI: Fan [C2F2] (off)
[ 11.295481] ACPI: Transitioning device [C2F3] to D3
[ 11.295483] ACPI: Transitioning device [C2F3] to D3
[ 11.295485] ACPI: Fan [C2F3] (off)
[ 11.295615] ACPI: Transitioning device [C2F4] to D3
[ 11.295616] ACPI: Transitioning device [C2F4] to D3
[ 11.295618] ACPI: Fan [C2F4] (off)
[ 11.295748] ACPI: Transitioning device [C2F5] to D3
[ 11.295749] ACPI: Transitioning device [C2F5] to D3
[ 11.295752] ACPI: Fan [C2F5] (off)
[ 11.300894] ACPI: SSDT 7F7F4852, 027F (r1 HP Cpu0Ist 3000 INTL 20060317)
[ 11.301064] ACPI: SSDT 7F7F4B56, 04CB (r1 HP Cpu0Cst 3001 INTL 20060317)
[ 11.306549] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 11.306552] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 11.306720] ACPI: SSDT 7F7F478A, 00C8 (r1 HP Cpu1Ist 3000 INTL 20060317)
[ 11.306878] ACPI: SSDT 7F7F4AD1, 0085 (r1 HP Cpu1Cst 3000 INTL 20060317)
[ 11.307579] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 11.307583] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 11.332605] ACPI: Thermal Zone [TZ0] (55 C)
[ 11.346794] ACPI: Thermal Zone [TZ1] (52 C)
[ 11.360529] ACPI: Thermal Zone [TZ2] (43 C)
[ 11.369710] ACPI: Thermal Zone [TZ3] (28 C)
[ 11.373380] ACPI: Thermal Zone [TZ4] (42 C)
[ 11.709700] usbcore: registered new interface driver usbfs
[ 11.709720] usbcore: registered new interface driver hub
[ 11.709793] usbcore: registered new device driver usb
[ 11.726037] USB Universal Host Controller Interface driver v3.0
[ 11.726098] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
[ 11.726110] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 11.726115] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 11.726376] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 11.726410] uhci_hcd 0000:00:1d.0: irq 19, io base 0x00003020
[ 11.726532] usb usb1: configuration #1 chosen from 1 choice
[ 11.726552] hub 1-0:1.0: USB hub found
[ 11.726557] hub 1-0:1.0: 2 ports detected
[ 11.743092] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 11.743095] e100: Copyright(c) 1999-2006 Intel Corporation
[ 11.772081] SCSI subsystem initialized
[ 11.815048] libata version 3.00 loaded.
[ 11.828645] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
[ 11.828658] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 11.828661] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 11.828685] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 11.832576] ehci_hcd 0000:00:1d.7: debug port 1
[ 11.832582] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 11.832587] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xf0584000
[ 11.847462] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 11.847564] usb usb2: configuration #1 chosen from 1 choice
[ 11.847584] hub 2-0:1.0: USB hub found
[ 11.847589] hub 2-0:1.0: 8 ports detected
[ 11.951409] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 19
[ 11.979038] e100: eth0: e100_probe: addr 0xf0101000, irq 19, MAC addr 00:1e:ec:23:76:37
[ 11.979053] ata_piix 0000:00:1f.1: version 2.12
[ 11.979066] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 11.979100] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 11.979352] scsi0 : ata_piix
[ 11.979391] scsi1 : ata_piix
[ 11.979762] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x3040 irq 14
[ 11.979764] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x3048 irq 15
[ 12.298989] ata1.00: ATAPI: Optiarc DVD RW AD-7530B, NH02, max MWDMA2
[ 12.470555] ata1.00: configured for MWDMA2
[ 12.470610] ata2: port disabled. ignoring.
[ 12.472024] scsi 0:0:0:0: CD-ROM Optiarc DVD RW AD-7530B NH02 PQ: 0 ANSI: 5
[ 12.472493] ahci 0000:00:1f.2: version 3.0
[ 12.472521] ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 21 (level, low) -> IRQ 20
[ 12.472564] ahci 0000:00:1f.2: nr_ports (4) and implemented port map (0x1) don't match, using nr_ports
[ 12.472566] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
[ 12.514028] usb 1-2: new full speed USB device using uhci_hcd and address 2
[ 12.747416] usb 1-2: configuration #1 chosen from 1 choice
[ 13.471961] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode
[ 13.471969] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
[ 13.471978] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 13.472278] scsi2 : ahci
[ 13.472475] scsi3 : ahci
[ 13.472581] scsi4 : ahci
[ 13.472687] scsi5 : ahci
[ 13.472738] ata3: SATA max UDMA/133 abar m1024@0xf0585000 port 0xf0585100 irq 221
[ 13.472742] ata4: SATA max UDMA/133 abar m1024@0xf0585000 port 0xf0585180 irq 221
[ 13.472745] ata5: SATA max UDMA/133 abar m1024@0xf0585000 port 0xf0585200 irq 221
[ 13.472748] ata6: SATA max UDMA/133 abar m1024@0xf0585000 port 0xf0585280 irq 221
[ 14.110531] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 14.112574] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 14.112576] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 filtered out
[ 14.112628] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
[ 14.112691] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 14.113131] ata3.00: ATA-8: TOSHIBA MK1246GSX, LB214C, max UDMA/100
[ 14.113136] ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 14.115183] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 14.115185] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 filtered out
[ 14.115236] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
[ 14.115300] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 succeeded
[ 14.115756] ata3.00: configured for UDMA/100
[ 14.116767] ata3.00: configured for UDMA/100
[ 14.116772] ata3: EH complete
[ 14.437817] ata4: SATA link down (SStatus 0 SControl 0)
[ 14.753126] ata5: SATA link down (SStatus 0 SControl 0)
[ 15.072428] ata6: SATA link down (SStatus 0 SControl 0)
[ 15.072642] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1246GS LB21 PQ: 0 ANSI: 5
[ 15.081967] Driver 'sd' needs updating - please use bus_type methods
[ 15.083932] Driver 'sr' needs updating - please use bus_type methods
[ 15.092468] sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 15.092507] sd 2:0:0:0: [sda] Write Protect is off
[ 15.092513] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 15.092574] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.092684] sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 15.092718] sd 2:0:0:0: [sda] Write Protect is off
[ 15.092723] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 15.092775] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.092778] sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 15.096274] Uniform CD-ROM driver Revision: 3.20
[ 15.096360] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 15.170092] sda1 sda2 < sda5 >
[ 15.199132] sd 2:0:0:0: [sda] Attached SCSI disk
[ 15.202497] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 15.202514] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 15.356764] Attempting manual resume
[ 15.356768] swsusp: Resume From Partition 8:5
[ 15.356769] PM: Checking swsusp image.
[ 15.356957] PM: Resume from disk failed.
[ 15.408099] kjournald starting. Commit interval 5 seconds
[ 15.408115] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.487464] Linux agpgart interface v0.102
[ 21.575281] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 21.629091] agpgart: Detected an Intel 945GME Chipset.
[ 21.629882] agpgart: Detected 7932K stolen memory.
[ 21.644161] agpgart: AGP aperture is 256M @ 0xe0000000
[ 21.661597] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 21.694093] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 21.778922] input: Power Button (FF) as /devices/virtual/input/input3
[ 21.806670] ACPI: Power Button (FF) [PWRF]
[ 21.806783] input: Sleep Button (CM) as /devices/virtual/input/input4
[ 21.830622] ACPI: Sleep Button (CM) [C20B]
[ 21.830709] input: Lid Switch as /devices/virtual/input/input5
[ 21.830788] ACPI: Lid Switch [C20C]
[ 21.841643] intel_rng: FWH not detected
[ 21.873927] ACPI: AC Adapter [C1AB] (on-line)
[ 21.981769] ACPI: Battery Slot [C1AC] (battery present)
[ 22.045638] iTCO_vendor_support: vendor-support=0
[ 22.081119] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 22.081200] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[ 22.081233] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 22.184110] ACPI: WMI-Acer: Mapper loaded
[ 22.321122] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 22.352472] ACPI: Video Device [C085] (multi-head: yes rom: no post: no)
[ 22.743694] Yenta: CardBus bridge found at 0000:02:06.0 [103c:30d5]
[ 22.743720] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 22.743722] Yenta: Routing CardBus interrupts to PCI
[ 22.743727] Yenta TI: socket 0000:02:06.0, mfunc 0x01be1b32, devctl 0x44
[ 22.975928] Yenta: ISA IRQ mask 0x0cf8, PCI irq 18
[ 22.975932] Socket status: 30000006
[ 22.975934] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 22.975939] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[ 22.975941] cs: IO port probe 0x2000-0x2fff: clean.
[ 22.976144] pcmcia: parent PCI bridge Memory window: 0xf0100000 - 0xf03fffff
[ 23.016010] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.0
[ 23.016026] iwl3945: Copyright(c) 2003-2007 Intel Corporation
[ 23.034693] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 23.034709] PCI: Setting latency timer of device 0000:10:00.0 to 64
[ 23.034730] iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
[ 23.139958] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 23.139980] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 23.244575] usbcore: registered new interface driver snd-usb-audio
[ 23.292302] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04711/0xa00000
[ 23.332320] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[ 24.008691] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 24.008998] wmaster0: Selected rate control algorithm 'iwl-3945-rs'
[ 24.145242] cs: IO port probe 0x100-0x3af: clean.
[ 24.147230] cs: IO port probe 0x3e0-0x4ff: clean.
[ 24.148045] cs: IO port probe 0x820-0x8ff: clean.
[ 24.148723] cs: IO port probe 0xc00-0xcf7: clean.
[ 24.149545] cs: IO port probe 0xa00-0xaff: clean.
[ 24.285756] lp: driver loaded but no devices found
[ 24.344158] Linux video capture interface: v2.00
[ 24.388935] usbcore: registered new interface driver ov51x
[ 24.388940] /home/nils2rs/Bureau/ov51x-jpeg-1.5.9/ov51x-jpeg-core.c: 1.5.9 : ov51x USB Camera Driver
[ 24.436437] Adding 4803392k swap on /dev/sda5. Priority:-1 extents:1 across:4803392k
[ 24.964530] EXT3 FS on sda1, internal journal
[ 26.173300] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 26.522113] No dock devices found.
[ 27.472168] apm: BIOS not found.
[ 27.622954] ppdev: user-space parallel port driver
[ 27.797268] audit(1223922015.616:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5123 profile="/usr/sbin/cupsd" namespace="default"
[ 28.978177] Bluetooth: Core ver 2.11
[ 28.978627] NET: Registered protocol family 31
[ 28.978634] Bluetooth: HCI device and connection manager initialized
[ 28.978640] Bluetooth: HCI socket layer initialized
[ 29.000935] Bluetooth: L2CAP ver 2.9
[ 29.000942] Bluetooth: L2CAP socket layer initialized
[ 29.011771] Bluetooth: RFCOMM socket layer initialized
[ 29.011791] Bluetooth: RFCOMM TTY layer initialized
[ 29.011795] Bluetooth: RFCOMM ver 1.8
[ 32.715945] [drm] Initialized drm 1.1.0 20060810
[ 32.719591] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 32.719606] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 32.719705] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 50.656451] NET: Registered protocol family 10
[ 50.656874] lo: Disabled Privacy Extensions
[ 50.657562] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 50.658356] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 59.220572] CPU0 attaching NULL sched-domain.
[ 59.220579] CPU1 attaching NULL sched-domain.
[ 59.228835] CPU0 attaching sched-domain:
[ 59.228841] domain 0: span 03
[ 59.228845] groups: 01 02
[ 59.228851] CPU1 attaching sched-domain:
[ 59.228854] domain 0: span 03
[ 59.228857] groups: 02 01
[ 63.607928] NET: Registered protocol family 17
[ 66.374014] wlan0: Initial auth_alg=0
[ 66.374024] wlan0: authenticate with AP 00:0f:3d:fc:c4:fe
[ 66.374704] wlan0: Initial auth_alg=0
[ 66.374711] wlan0: authenticate with AP 00:0f:3d:fc:c4:fe
[ 66.375475] wlan0: RX authentication from 00:0f:3d:fc:c4:fe (alg=0 transaction=2 status=0)
[ 66.375478] wlan0: authenticated
[ 66.375480] wlan0: associate with AP 00:0f:3d:fc:c4:fe
[ 66.395032] wlan0: authentication frame received from 00:0f:3d:fc:c4:fe, but not in authenticate state - ignored
[ 66.415234] wlan0: RX AssocResp from 00:0f:3d:fc:c4:fe (capab=0x461 status=0 aid=1)
[ 66.415240] wlan0: associated
[ 66.416727] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 81.399317] wlan0: no IPv6 routers present
[ 187.971228] usb 1-2: USB disconnect, address 2
[ 191.785840] usb 1-1: new full speed USB device using uhci_hcd and address 3
[ 192.022560] usb 1-1: configuration #1 chosen from 1 choice
[ 667.066132] usb 1-1: USB disconnect, address 3
[ 673.792382] usb 1-2: new full speed USB device using uhci_hcd and address 4
[ 674.028083] usb 1-2: configuration #1 chosen from 1 choice
[ 812.571815] usb 1-2: USB disconnect, address 4
[ 817.638375] usb 2-2: new high speed USB device using ehci_hcd and address 5
[ 817.770383] usb 2-2: configuration #1 chosen from 2 choices
[ 817.859359] usbcore: registered new interface driver libusual
[ 817.870999] Initializing USB Mass Storage driver...
[ 817.871624] scsi6 : SCSI emulation for USB Mass Storage devices
[ 817.871771] usbcore: registered new interface driver usb-storage
[ 817.871774] USB Mass Storage support registered.
[ 817.872008] usb-storage: device found at 5
[ 817.872010] usb-storage: waiting for device to settle before scanning
[ 822.858450] usb-storage: device scan complete
[ 822.858935] scsi 6:0:0:0: Direct-Access Apple iPod 2.70 PQ: 0 ANSI: 4
[ 822.862130] sd 6:0:0:0: [sdb] 1010432 512-byte hardware sectors (517 MB)
[ 822.863254] sd 6:0:0:0: [sdb] Write Protect is off
[ 822.863260] sd 6:0:0:0: [sdb] Mode Sense: 64 00 00 08
[ 822.863265] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 822.865495] sd 6:0:0:0: [sdb] 1010432 512-byte hardware sectors (517 MB)
[ 822.866247] sd 6:0:0:0: [sdb] Write Protect is off
[ 822.866253] sd 6:0:0:0: [sdb] Mode Sense: 64 00 00 08
[ 822.866257] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 822.866262] sdb: sdb1
[ 822.868178] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 822.868254] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 830.602676] usb 2-2: USB disconnect, address 5
[ 830.603182] Buffer I/O error on device sdb1, logical block 2024
[ 830.603191] lost page write due to I/O error on sdb1
[ 830.603197] Buffer I/O error on device sdb1, logical block 2025
[ 830.603201] lost page write due to I/O error on sdb1
[ 830.603214] Buffer I/O error on device sdb1, logical block 526312
[ 830.603218] lost page write due to I/O error on sdb1
[ 830.693140] scsi 6:0:0:0: rejecting I/O to dead device
[ 834.165551] usb 1-2: new full speed USB device using uhci_hcd and address 5
[ 834.401255] usb 1-2: configuration #1 chosen from 1 choice
[ 2619.514880] usb 1-2: USB disconnect, address 5
[ 2626.520523] usb 1-2: new full speed USB device using uhci_hcd and address 6
[ 2626.756221] usb 1-2: configuration #1 chosen from 1 choice
[ 6074.948803] UDF-fs: No VRS found
[ 6074.973826] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 6075.007020] ISO 9660 Extensions: RRIP_1991A
[ 6851.888300] sr0: CDROM not ready. Make sure there is a disc in the drive.
[ 6894.363035] usb 1-2: USB disconnect, address 6
[ 6976.855548] usb 1-1: new full speed USB device using uhci_hcd and address 7
[ 6977.093340] usb 1-1: configuration #1 chosen from 1 choice

herberts · Le 13/10/2008, à 22:26

Bon. Et un lsusb quand la webcam n'est pas branchée, ça donne quoi ?

Au passage, pour ton message précédent, quand tu postes des retours de commande, il faut utiliser la balise "code" et pas "quote", qui doit être utilisée seulement pour citer quelqu'un

nils2rs · Le 13/10/2008, à 22:34

Bus 002 Device 001: ID 0000:0000  
Bus 001 Device 001: ID 0000:000

Voilà sans la webcam

(merci du conseil)

herberts · Le 13/10/2008, à 22:40

C'est étrange... Ta webcam est bien reconnue par le lsusb, mais elle n'a pas les identifiant des autres hercules que j'ai pu rencontrer. C'est quoi le modèle exact ? c'est une "classic" tout court ou c'est une nouvelle version ?

nils2rs · Le 13/10/2008, à 22:49

Voilà la bête : http://www.ldlc.com/fiche/PB00073275.html

(saloperie )

herberts · Le 13/10/2008, à 23:26

Ah ok. Donc c'est bien une "nouvelle" version. Ma classic "tout court" renvoie

ID 05a9:4519 OmniVision Technologies, Inc. Webcam Classic

avec lsusb. Du coup je sais pas trop quoi te dire là.

ggcom · Le 10/01/2009, à 01:23

La webcam ID 06f8:3009 Guillemot Corp (hercules Classic Link) n'est pas prise en charge par ov51x-jpeg (voir http://www.rastageeks.org/ov51x-jpeg/in … ng_Webcams)

Cest un peu tard pour le dire mais bon...

ggcom · Le 13/01/2009, à 00:58

J'ai envoyé un message à hercules pour demander s'il y avait un pilote Linux.
Il m'ont répondu rapidement (lundi alors que la question n'a été envoyée que le samedi) qu'il n'y avait pas de pilote.
Cependant le type de chipset est
"chipset SOC Pixart 7302"

avec un petit google il semblerait que le moment de son support ne soit plus très loin.

pitivie · Le 14/03/2009, à 15:59

alors tu a réussi (j'ai la même webcam depuis peu:D) ?

pitivie · Le 27/03/2009, à 21:11

petit up

Claudiu · Le 08/04/2009, à 01:48

J'ai le meme web cam e le meme probleme en Ubuntu 8.04. Qu est ce que je peut faire pour installer le camera?

Glaedr · Le 23/04/2009, à 19:59

J'ai le meme web cam e le meme probleme en Ubuntu 8.04. Qu est ce que je peut faire pour installer le camera?

meme problème...mais la webcam, c'est trop neuve...tu n'a lit pas ça:

J'ai envoyé un message à hercules pour demander s'il y avait un pilote Linux.
Il m'ont répondu rapidement (lundi alors que la question n'a été envoyée que le samedi) qu'il n'y avait pas de pilote.
Cependant le type de chipset est
"chipset SOC Pixart 7302"
avec un petit google il semblerait que le moment de son support ne soit plus très loin.

la solution du problème serait un paquet de sorgents, qui serait compatible par toutes les distros, quand un deb qui marche sur 8.10 ne marche pas sur 8.04...!
le problème est que les producteurs font de la speculation avec les pilotes: si tu vas les chercher sur le site web de Hercules, tu en trouves seulement pour xp ou Vista! beaucoup d'autres producteurs de hardwares moins connus et moins chéres font la meme chose: ils gagnent plus des argents par les incentifs de chiez Microsoft!

Stemp · Le 23/08/2009, à 11:42

Ouaip c'est pas gagné quand même, le support des senseurs pac7302 est bien intégré dans le driver gspca v2.
Malheureusement dans le cas de cette webcam ça ne fonctionne pas encore comme prévu.

Stemp · Le 23/08/2009, à 13:35

C'est quand même mieux \o/

Ludo92 · Le 30/08/2009, à 10:51

Très intéressant. Comment avez-vous procédé? Pourriez-vous faire un rapide tutoriel pour expliquer la démarche?

En vous remerciant d'avance

Ludovic

Stemp · Le 30/08/2009, à 12:07

Salut Ludo92,

Mon patch a été accepté par les développeurs de libv4l et de gspca, il faut donc compiler ou récupérer les dernières versions.

Pour Libv4l c'est plus simple puisque j'ai mis à jour le paquet dans mon PPA (il faut aussi installer le paquet -dev).

Pour Gspca v2, il faut cloner le code source du dépôt de Jean-François Moine (il vous faudra installer les paquets mercurial, build-essential et linux-headers).

hg clone http://linuxtv.org/hg/~jfrancois/gspca/
cd gspca
make all
sudo make install

Dernière modification par Stemp (Le 30/08/2009, à 12:07)

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 13/10/2008, à 21:06

[EN COURS] Installation webcam HERCULES CLASSIC LINK

#2 Le 13/10/2008, à 21:40

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#3 Le 13/10/2008, à 21:49

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#4 Le 13/10/2008, à 21:50

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#5 Le 13/10/2008, à 22:09

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#6 Le 13/10/2008, à 22:11

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#7 Le 13/10/2008, à 22:14

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#8 Le 13/10/2008, à 22:17

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#9 Le 13/10/2008, à 22:17

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#10 Le 13/10/2008, à 22:19

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#11 Le 13/10/2008, à 22:26

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#12 Le 13/10/2008, à 22:34

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#13 Le 13/10/2008, à 22:40

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#14 Le 13/10/2008, à 22:49

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#15 Le 13/10/2008, à 23:26

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#16 Le 10/01/2009, à 01:23

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#17 Le 13/01/2009, à 00:58

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#18 Le 14/03/2009, à 15:59

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#19 Le 27/03/2009, à 21:11

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#20 Le 08/04/2009, à 01:48

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#21 Le 23/04/2009, à 19:59

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#22 Le 23/08/2009, à 11:42

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#23 Le 23/08/2009, à 13:35

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#24 Le 30/08/2009, à 10:51

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

#25 Le 30/08/2009, à 12:07

Re : [EN COURS] Installation webcam HERCULES CLASSIC LINK

Pied de page des forums