Ubuntu-fr

LinePo

[Résolu] Disque dur externe mal monté?

Bonjour,

J'ai un nouveau disque dur, tout droit sorti de son emballage, mais impossible de le monter correctement et de le faire fonctionner.

Au début, il ne se montait pas du tout, car je n'avais pas les droits suffisants pour le faire, apparement. Le message d'erreur "hal-storage-removable-mount-all-options refused uid 1000" apparaissait.

Du coup, pour régler ce problème, j'ai décoché la case "Monter en tant qu'utilisateur", dans les propriétés de mon DDE.

Maintenant qu'il est monté, il m'est impossible d'y glisser le moindre fichier (Impossible d'écrire dans media:/).
De plus, il m'assure que mon DDE(sdc1) fait 10Mo (alors qu'il en fait 500Go)...

J'ai essayé de le formater avec Gparted, mais ici encore, problème.
Lorsque je démarre Gparted, une nouvelle partition semble se créer : sdc2
Et je n'arrive pas à formater ni sdc1, ni sdc2...

Bref, j'ai l'impression d'être en face d'un casse tête chinois. Quelqu'un peut-il m'aider?

Voilà quelques lignes de commandes qui, j'espère, vous permettront de m'aider

lsusb
Bus 003 Device 005: ID 059f:1010 LaCie, Ltd
Bus 003 Device 004: ID 05ac:1209 Apple Computer, Inc.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 046d:c51b Logitech, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

dmesg
[    0.000000] Linux version 2.6.22-16-generic (buildd@rothera) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Mon Jan 26 00:07:52 GMT 2009 (Ubuntu 2.6.22-16.61-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000037e80000 (usable)
[    0.000000]  BIOS-e820: 0000000037e80000 - 0000000037e8f000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000037e8f000 - 0000000037f00000 (ACPI NVS)
[    0.000000]  BIOS-e820: 0000000037f00000 - 0000000040000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 894MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f8950
[    0.000000] Entering add_active_range(0, 0, 228992) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   228992
[    0.000000]   HighMem    228992 ->   228992
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   228992
[    0.000000] On node 0 totalpages: 228992
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1757 pages used for memmap
[    0.000000]   Normal zone: 223139 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F8890 checksum 0
[    0.000000] ACPI: RSDP 000F8890, 0014 (r0 FSC   )
[    0.000000] ACPI: RSDT 37E891A3, 003C (r1 FSC    PC        6040000  LTP        0)
[    0.000000] ACPI: FACP 37E8EC85, 0074 (r1 FSC    PC        6040000 ATI     F4240)
[    0.000000] ACPI: DSDT 37E891DF, 5AA6 (r1 UW____ F33_____  6040000 MSFT  2000001)
[    0.000000] ACPI: FACS 37E8FFC0, 0040
[    0.000000] ACPI: TCPA 37E8ECF9, 0032 (r2 FSC    PC        6040000 PTEC        0)
[    0.000000] ACPI: APIC 37E8ED2B, 0050 (r1 FSC    PC        6040000  LTP        0)
[    0.000000] ACPI: SLIC 37E8ED7B, 0176 (r1 FSC    PC        6040000  LTP        0)
[    0.000000] ACPI: MCFG 37E8EEF1, 003C (r1 FSC    PC        6040000  LTP        0)
[    0.000000] ACPI: SSDT 37E8EF2D, 00D3 (r1 FSC    PC        6040000  LTP        1)
[    0.000000] ATI board detected. Disabling timer routing over 8254.
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:12 APIC version 16
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[    0.000000] Built 1 zonelists.  Total pages: 227203
[    0.000000] Kernel command line: root=UUID=db52ffa6-005c-4989-bfa2-0f7ebc7426a6 ro quiet splash
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1596.167 MHz processor.
[   18.119517] Console: colour VGA+ 80x25
[   18.119833] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   18.120236] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   18.135881] Memory: 896516k/915968k available (2017k kernel code, 18912k reserved, 918k data, 364k init, 0k highmem)
[   18.135893] virtual kernel memory layout:
[   18.135895]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   18.135896]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   18.135898]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   18.135899]     lowmem  : 0xc0000000 - 0xf7e80000   ( 894 MB)
[   18.135901]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   18.135902]       .data : 0xc02f84c6 - 0xc03dde84   ( 918 kB)
[   18.135904]       .text : 0xc0100000 - 0xc02f84c6   (2017 kB)
[   18.135907] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   18.135944] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   18.215899] Calibrating delay using timer specific routine.. 3195.59 BogoMIPS (lpj=6391184)
[   18.215924] Security Framework v1.0.0 initialized
[   18.215929] SELinux:  Disabled at boot.
[   18.215943] Mount-cache hash table entries: 512
[   18.216052] CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
[   18.216061] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[   18.216064] CPU: L2 Cache: 512K (64 bytes/line)
[   18.216067] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019
[   18.216077] Compat vDSO mapped to ffffe000.
[   18.216087] Checking 'hlt' instruction... OK.
[   18.231995] SMP alternatives: switching to UP code
[   18.232144] Freeing SMP alternatives: 11k freed
[   18.232413] Early unpacking initramfs... done
[   18.588744] ACPI: Core revision 20070126
[   18.588824] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   18.998195] CPU0: AMD Mobile AMD Sempron(tm) Processor 3200+ stepping 02
[   18.998217] Total of 1 processors activated (3195.59 BogoMIPS).
[   18.998384] ENABLING IO-APIC IRQs
[   18.998582] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[   19.143131] Brought up 1 CPUs
[   19.143234] Booting paravirtualized kernel on bare hardware
[   19.143316] Time:  7:19:00  Date: 02/18/109
[   19.143336] NET: Registered protocol family 16
[   19.143415] EISA bus registered
[   19.143432] ACPI: bus type pci registered
[   19.166281] PCI: BIOS BUG #81[49435000] found
[   19.166326] PCI: Using configuration type 1
[   19.166328] Setting up standard PCI resources
[   19.167966] ACPI: EC: Look up EC in DSDT
[   19.168429] ACPI: EC: GPE=0x11, ports=0x66, 0x62
[   19.169864] ACPI: Interpreter enabled
[   19.169867] ACPI: (supports S0 S3 S4 S5)
[   19.169881] ACPI: Using IOAPIC for interrupt routing
[   19.174369] ACPI: EC: GPE=0x11, ports=0x66, 0x62
[   19.174416] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   19.174425] PCI: Probing PCI hardware (bus 00)
[   19.175847] PCI: Transparent bridge - 0000:00:14.4
[   19.175886] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   19.176051] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[   19.176180] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[   19.176302] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[   19.179218] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[   19.179342] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[   19.179457] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[   19.179573] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[   19.179691] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[   19.179808] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[   19.179926] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[   19.180043] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[   19.180165] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
[   19.180246] Linux Plug and Play Support v0.97 (c) Adam Belay
[   19.180260] pnp: PnP ACPI init
[   19.180267] ACPI: bus type pnp registered
[   19.182360] pnp: PnP ACPI: found 10 devices
[   19.182362] ACPI: ACPI bus type pnp unregistered
[   19.182366] PnPBIOS: Disabled by ACPI PNP
[   19.182412] PCI: Using ACPI for IRQ routing
[   19.182415] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   19.182422] PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
[   19.182466] PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
[   19.182599] NET: Registered protocol family 8
[   19.182602] NET: Registered protocol family 20
[   19.182658] pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[   19.182662] pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
[   19.182666] pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
[   19.182674] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
[   19.182677] pnp: 00:08: ioport range 0x200-0x20f has been reserved
[   19.182680] pnp: 00:08: ioport range 0x220-0x22f has been reserved
[   19.182683] pnp: 00:08: ioport range 0x40b-0x40b has been reserved
[   19.182689] pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved
[   19.182693] pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[   19.182696] pnp: 00:09: iomem range 0x0-0xfff could not be reserved
[   19.183067] Time: tsc clocksource has been installed.
[   19.212955] PCI: Bridge: 0000:00:01.0
[   19.212957]   IO window: 9000-9fff
[   19.212961]   MEM window: c0100000-c01fffff
[   19.212964]   PREFETCH window: c8000000-cfffffff
[   19.212968] PCI: Bridge: 0000:00:04.0
[   19.212970]   IO window: disabled.
[   19.212972]   MEM window: disabled.
[   19.212974]   PREFETCH window: disabled.
[   19.212982] PCI: Bridge: 0000:00:14.4
[   19.212986]   IO window: a000-afff
[   19.212993]   MEM window: c0200000-c02fffff
[   19.212997]   PREFETCH window: disabled.
[   19.213016] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   19.213036] NET: Registered protocol family 2
[   19.247045] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   19.247152] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[   19.248218] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   19.248566] TCP: Hash tables configured (established 131072 bind 65536)
[   19.248569] TCP reno registered
[   19.259125] checking if image is initramfs... it is
[   19.714609] Switched to high resolution mode on CPU 0
[   19.959383] Freeing initrd memory: 7070k freed
[   19.959733] audit: initializing netlink socket (disabled)
[   19.959745] audit(1237360740.040:1): initialized
[   19.961522] VFS: Disk quotas dquot_6.5.1
[   19.961568] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.961648] io scheduler noop registered
[   19.961650] io scheduler anticipatory registered
[   19.961652] io scheduler deadline registered
[   19.961670] io scheduler cfq registered (default)
[   19.961678] PCI: MSI quirk detected. MSI deactivated.
[   19.961721] Boot video device is 0000:01:05.0
[   19.961800] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   19.961822] assign_interrupt_mode Found MSI capability
[   19.961824] Allocate Port Service[0000:00:04.0:pcie00]
[   19.961856] Allocate Port Service[0000:00:04.0:pcie02]
[   19.961964] isapnp: Scanning for PnP cards...
[   20.318454] isapnp: No Plug & Play device found
[   20.341825] Real Time Clock Driver v1.12ac
[   20.341909] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   20.343007] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   20.343183] input: Macintosh mouse button emulation as /class/input/input0
[   20.343247] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[   20.346036] i8042.c: Detected active multiplexing controller, rev 1.1.
[   20.347514] serio: i8042 KBD port at 0x60,0x64 irq 1
[   20.347519] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   20.347522] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   20.347525] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   20.347528] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   20.347714] mice: PS/2 mouse device common for all mice
[   20.347919] EISA: Probing bus 0 at eisa.0
[   20.347931] Cannot allocate resource for EISA slot 1
[   20.347962] Cannot allocate resource for EISA slot 8
[   20.347964] EISA: Detected 0 cards.
[   20.348051] TCP cubic registered
[   20.348062] NET: Registered protocol family 1
[   20.348084] Using IPI No-Shortcut mode
[   20.348247]   Magic number: 1:345:319
[   20.348361]   hash matches device tty44
[   20.348641] Freeing unused kernel memory: 364k freed
[   20.348660] Write protecting the kernel read-only data: 726k
[   20.431359] input: AT Translated Set 2 keyboard as /class/input/input1
[   21.546205] AppArmor: AppArmor initialized<5>audit(1237360741.540:2):  type=1505 info="AppArmor initialized" pid=1213
[   21.668561] fuse init (API version 7.8)
[   21.773044] Failure registering capabilities with primary security module.
[   21.879496] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   21.879502] ACPI: Processor [CPU0] (supports 8 throttling states)
[   21.879514] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[   22.276386] ACPI: Thermal Zone [THRM] (25 C)
[   31.854303] SCSI subsystem initialized
[   31.969742] libata version 2.21 loaded.
[   31.973114] sata_sil 0000:00:12.0: version 2.2
[   31.973161] PCI: Enabling device 0000:00:12.0 (0005 -> 0007)
[   31.973171] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 16
[   31.973243] scsi0 : sata_sil
[   31.973284] scsi1 : sata_sil
[   31.973439] ata1: SATA max UDMA/100 cmd 0xf8840080 ctl 0xf884008a bmdma 0xf8840000 irq 16
[   31.973445] ata2: SATA max UDMA/100 cmd 0xf88400c0 ctl 0xf88400ca bmdma 0xf8840008 irq 16
[   31.981087] usbcore: registered new interface driver usbfs
[   31.981111] usbcore: registered new interface driver hub
[   31.981131] usbcore: registered new device driver usb
[   31.981805] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[   32.230803] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   32.230809] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   32.439244] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   32.827146] ata1.00: ATA-7: WDC WD1200BEVS-07LAT0, 01.06M01, max UDMA/133
[   32.827152] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/1)
[   32.843486] ata1.00: configured for UDMA/100
[   33.154586] ata2: SATA link down (SStatus 0 SControl 310)
[   33.162583] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1200BEVS-0 01.0 PQ: 0 ANSI: 5
[   33.162749] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 17
[   33.162763] ohci_hcd 0000:00:13.0: OHCI Host Controller
[   33.162898] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[   33.162922] ohci_hcd 0000:00:13.0: irq 17, io mem 0xc0005000
[   33.218643] usb usb1: configuration #1 chosen from 1 choice
[   33.218669] hub 1-0:1.0: USB hub found
[   33.218682] hub 1-0:1.0: 4 ports detected
[   33.264412] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[   33.322560] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 17
[   33.322578] ohci_hcd 0000:00:13.1: OHCI Host Controller
[   33.322603] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[   33.322620] ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000
[   33.378470] usb usb2: configuration #1 chosen from 1 choice
[   33.378499] hub 2-0:1.0: USB hub found
[   33.378513] hub 2-0:1.0: 4 ports detected
[   33.482517] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 17
[   33.482531] ehci_hcd 0000:00:13.2: EHCI Host Controller
[   33.482556] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[   33.482605] ehci_hcd 0000:00:13.2: irq 17, io mem 0xc0007000
[   33.482617] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   33.482723] usb usb3: configuration #1 chosen from 1 choice
[   33.482751] hub 3-0:1.0: USB hub found
[   33.482758] hub 3-0:1.0: 8 ports detected
[   33.586372] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[   33.586395] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18
[   33.586407] ATIIXP: chipset revision 128
[   33.586410] ATIIXP: not 100% native mode: will probe irqs later
[   33.586419]     ide0: BM-DMA at 0x8460-0x8467, BIOS settings: hda:DMA, hdb:pio
[   33.586435] ATIIXP: simplex device: DMA disabled
[   33.586437] ide1: ATIIXP Bus-Master DMA disabled (BIOS)
[   33.586443] Probing IDE interface ide0...
[   33.905922] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[   33.909904] sd 0:0:0:0: [sda] Write Protect is off
[   33.909907] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   33.917886] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   33.925889] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[   33.929883] sd 0:0:0:0: [sda] Write Protect is off
[   33.929886] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   33.937867] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   33.937872]  sda: sda1 sda2 < sda5 >
[   34.026967] sd 0:0:0:0: [sda] Attached SCSI disk
[   34.030729] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   34.197641] usb 2-4: new low speed USB device using ohci_hcd and address 2
[   34.321951] hda: Optiarc DVD RW AD-7540A, ATAPI CD/DVD-ROM drive
[   34.405520] usb 2-4: configuration #1 chosen from 1 choice
[   34.423281] usbcore: registered new interface driver hiddev
[   34.436719] input: Logitech USB Receiver as /class/input/input2
[   34.436855] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-4
[   34.442560] hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.1-4
[   34.442572] usbcore: registered new interface driver usbhid
[   34.442575] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   34.992945] hda: selected mode 0x42
[   34.993153] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   34.994405] Probing IDE interface ide1...
[   35.557626] PCI: Enabling device 0000:05:04.0 (0015 -> 0017)
[   35.557637] ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 20 (level, low) -> IRQ 19
[   35.615978] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[c0211000-c02117ff]  Max Packet=[2048]  IR/IT contexts=[8/8]
[   35.616154] 8139cp 0000:05:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[   35.616158] 8139cp 0000:05:05.0: Try the "8139too" driver instead.
[   35.619080] 8139too Fast Ethernet driver 0.9.28
[   35.619377] ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 21 (level, low) -> IRQ 21
[   35.620487] eth0: RealTek RTL8139 at 0xf8900c00, 00:03:0d:5c:1a:19, IRQ 21
[   35.620491] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[   35.621626] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[   35.621634] Uniform CD-ROM driver Revision: 3.20
[   36.111706] Attempting manual resume
[   36.111710] swsusp: Resume From Partition 8:5
[   36.111712] PM: Checking swsusp image.
[   36.207835] PM: Resume from disk failed.
[   36.883338] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00030d0000001234]
[   37.318884] kjournald starting.  Commit interval 5 seconds
[   37.318895] EXT3-fs: mounted filesystem with ordered data mode.
[  131.912398] Linux agpgart interface v0.102 (c) Dave Jones
[  131.930655] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[  131.934150] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  133.174149] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[  133.489530] usbcore: registered new interface driver xpad
[  133.489535] /build/buildd/linux-source-2.6.22-2.6.22/drivers/input/joystick/xpad.c: driver for Xbox controllers v0.1.6
[  133.835312] ath_hal: module license 'Proprietary' taints kernel.
[  133.836011] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[  133.906492] wlan: 0.8.4.2 (0.9.3.2)
[  133.944799] ath_pci: 0.9.4.5 (0.9.3.2)
[  133.944870] ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 23 (level, low) -> IRQ 20
[  134.878261] sdhci: Secure Digital Host Controller Interface driver
[  134.878265] sdhci: Copyright(c) Pierre Ossman
[  135.009879] ath_rate_sample: 1.2 (0.9.3.2)
[  135.247433] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[  135.247440] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[  135.247450] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[  135.247454] wifi0: mac 7.8 phy 4.5 radio 5.6
[  135.247458] wifi0: Use hw queue 1 for WME_AC_BE traffic
[  135.247461] wifi0: Use hw queue 0 for WME_AC_BK traffic
[  135.247463] wifi0: Use hw queue 2 for WME_AC_VI traffic
[  135.247465] wifi0: Use hw queue 3 for WME_AC_VO traffic
[  135.247468] wifi0: Use hw queue 8 for CAB traffic
[  135.247470] wifi0: Use hw queue 9 for beacons
[  135.285971] wifi0: Atheros 5212: mem=0xc0200000, irq=20
[  135.286020] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
[  135.500000] input: PC Speaker as /class/input/input3
[  135.601275] input: PS/2 Logitech Wheel Mouse as /class/input/input4
[  135.662869] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[  135.822941] sdhci: SDHCI controller found at 0000:05:04.2 [1217:7120] (rev 1)
[  135.822968] ACPI: PCI Interrupt 0000:05:04.2[A] -> GSI 20 (level, low) -> IRQ 19
[  135.822988] sdhci:slot0: Unknown controller version (16). You may experience problems.
[  135.823057] mmc0: SDHCI at 0xc0210800 irq 19 PIO
[  139.182189] lp: driver loaded but no devices found
[  139.316747] Adding 2642652k swap on /dev/sda5.  Priority:-1 extents:1 across:2642652k
[  310.068000] Marking TSC unstable due to: possible TSC halt in C2.
[  310.072000] Time: acpi_pm clocksource has been installed.
[  602.832000] EXT3 FS on sda1, internal journal
[  605.672000] input: Power Button (FF) as /class/input/input5
[  605.672000] ACPI: Power Button (FF) [PWRF]
[  605.692000] input: Lid Switch as /class/input/input6
[  605.692000] ACPI: Lid Switch [LID]
[  605.764000] input: Power Button (CM) as /class/input/input7
[  605.764000] ACPI: Power Button (CM) [PWRB]
[  605.804000] input: Sleep Button (CM) as /class/input/input8
[  605.808000] ACPI: Sleep Button (CM) [SLPB]
[  605.872000] No dock devices found.
[  605.928000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[  605.952000] ACPI: AC Adapter [AC0] (on-line)
[  605.972000] ACPI: Battery Slot [BAT0] (battery absent)
[  606.432000] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 3200+ processors (version 2.00.00)
[  606.432000] powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x11
[  606.432000] powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x18
[  610.120000] eth0: link down
[  610.176000] Failure registering capabilities with primary security module.
[  612.972000] [fglrx] Maximum main memory to use for locked dma buffers: 802 MBytes.
[  612.972000] [fglrx] module loaded - fglrx 8.37.6 [May 25 2007] on minor 0
[  613.140000] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 22
[  613.312000] ppdev: user-space parallel port driver
[  615.188000] [fglrx] total      GART = 130023424
[  615.188000] [fglrx] free       GART = 114032640
[  615.188000] [fglrx] max single GART = 114032640
[  615.188000] [fglrx] total      LFB  = 134217728
[  615.188000] [fglrx] free       LFB  = 119828480
[  615.188000] [fglrx] max single LFB  = 119828480
[  615.188000] [fglrx] total      Inv  = 0
[  615.188000] [fglrx] free       Inv  = 0
[  615.188000] [fglrx] max single Inv  = 0
[  615.188000] [fglrx] total      TIM  = 0
[  617.168000] audit(1237361357.423:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5162 profile="/usr/sbin/cupsd"
[  620.584000] apm: BIOS not found.
[  623.068000] Clocksource tsc unstable (delta = -250021950 ns)
[  624.792000] NET: Registered protocol family 10
[  624.792000] lo: Disabled Privacy Extensions
[  624.792000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  629.404000] Bluetooth: Core ver 2.11
[  629.404000] NET: Registered protocol family 31
[  629.404000] Bluetooth: HCI device and connection manager initialized
[  629.404000] Bluetooth: HCI socket layer initialized
[  629.596000] Bluetooth: L2CAP ver 2.8
[  629.596000] Bluetooth: L2CAP socket layer initialized
[  629.892000] Bluetooth: RFCOMM socket layer initialized
[  629.892000] Bluetooth: RFCOMM TTY layer initialized
[  629.892000] Bluetooth: RFCOMM ver 1.8
[  634.944000] ath0: no IPv6 routers present
[ 2072.004000] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 2085.116000] NET: Registered protocol family 17
[ 2103.556000] ath0: no IPv6 routers present
[ 8624.276000] usb 3-7: new high speed USB device using ehci_hcd and address 3
[ 8624.408000] usb 3-7: configuration #1 chosen from 2 choices
[ 8624.552000] usbcore: registered new interface driver libusual
[ 8624.588000] Initializing USB Mass Storage driver...
[ 8624.588000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 8624.588000] usb-storage: device found at 3
[ 8624.588000] usb-storage: waiting for device to settle before scanning
[ 8624.588000] usbcore: registered new interface driver usb-storage
[ 8624.588000] USB Mass Storage support registered.
[ 8629.588000] usb-storage: device scan complete
[ 8629.588000] scsi 2:0:0:0: Direct-Access     Apple    iPod             1.62 PQ: 0 ANSI: 0
[ 8629.588000] sd 2:0:0:0: [sdb] 58605120 512-byte hardware sectors (30006 MB)
[ 8629.592000] sd 2:0:0:0: [sdb] Write Protect is off
[ 8629.592000] sd 2:0:0:0: [sdb] Mode Sense: 68 00 00 08
[ 8629.592000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 8629.592000] sd 2:0:0:0: [sdb] 58605120 512-byte hardware sectors (30006 MB)
[ 8629.592000] sd 2:0:0:0: [sdb] Write Protect is off
[ 8629.592000] sd 2:0:0:0: [sdb] Mode Sense: 68 00 00 08
[ 8629.592000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 8629.592000]  sdb: sdb1 sdb2
[ 8629.608000] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 8629.608000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[10054.396000] usb 3-7: USB disconnect, address 3
[10329.320000] usb 3-7: new high speed USB device using ehci_hcd and address 4
[10329.452000] usb 3-7: configuration #1 chosen from 2 choices
[10329.452000] scsi3 : SCSI emulation for USB Mass Storage devices
[10329.452000] usb-storage: device found at 4
[10329.452000] usb-storage: waiting for device to settle before scanning
[10334.452000] usb-storage: device scan complete
[10334.452000] scsi 3:0:0:0: Direct-Access     Apple    iPod             1.62 PQ: 0 ANSI: 0
[10334.452000] sd 3:0:0:0: [sdb] 58605120 512-byte hardware sectors (30006 MB)
[10334.456000] sd 3:0:0:0: [sdb] Write Protect is off
[10334.456000] sd 3:0:0:0: [sdb] Mode Sense: 68 00 00 08
[10334.456000] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[10334.456000] sd 3:0:0:0: [sdb] 58605120 512-byte hardware sectors (30006 MB)
[10334.456000] sd 3:0:0:0: [sdb] Write Protect is off
[10334.456000] sd 3:0:0:0: [sdb] Mode Sense: 68 00 00 08
[10334.456000] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[10334.456000]  sdb: sdb1 sdb2
[10334.476000] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[10334.476000] sd 3:0:0:0: Attached scsi generic sg1 type 0
[10347.508000] hda_intel: azx_get_response timeout, switching to polling mode...
[10348.512000] hda_intel: azx_get_response timeout, switching to single_cmd mode...
[11628.224000] usb 3-6: new high speed USB device using ehci_hcd and address 5
[11628.368000] usb 3-6: configuration #1 chosen from 1 choice
[11628.372000] scsi4 : SCSI emulation for USB Mass Storage devices
[11628.372000] usb-storage: device found at 5
[11628.372000] usb-storage: waiting for device to settle before scanning
[11633.372000] usb-storage: device scan complete
[11633.376000] scsi 4:0:0:0: Direct-Access     ST350082 0AS                   PQ: 0 ANSI: 2
[11633.404000] sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[11633.404000] sd 4:0:0:0: [sdc] Write Protect is off
[11633.404000] sd 4:0:0:0: [sdc] Mode Sense: 38 00 00 00
[11633.404000] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[11633.428000] sd 4:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[11633.428000] sd 4:0:0:0: [sdc] Write Protect is off
[11633.428000] sd 4:0:0:0: [sdc] Mode Sense: 38 00 00 00
[11633.428000] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[11633.428000]  sdc: sdc1
[11633.440000] sd 4:0:0:0: [sdc] Attached SCSI disk
[11633.440000] sd 4:0:0:0: Attached scsi generic sg2 type 0

Dernière modification par LinePo (Le 25/03/2009, à 15:38)

Koshie-2.0

Re : [Résolu] Disque dur externe mal monté?

Salut,

Si c'est un problème de droit, à première vu je te dirais de faire un tour dans ton /etc/fstab afin de le déclarer et de lui donner les droits que tu veux.

Quelques liens : http://doc.ubuntu-fr.org/installation/mount_fstab

Je pense que tu auras besoin de savoir où est monté ton disque dur, un petit sudo fdisk -l te donnera cette info !

LinePo

Re : [Résolu] Disque dur externe mal monté?

Petit souci...

Voici mon fichier /etc/fstab et je ne vois pas mon DDE, qui devrait être monté sous sdb1

# /etc/fstab: static file system information.
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
proc            /proc           proc    defaults        0       0
# /dev/sda1
UUID=db52ffa6-005c-4989-bfa2-0f7ebc7426a6 /               ext3    defaults,errors=remount-ro 0       1
# /dev/sda5
UUID=9d7db29d-4a26-489f-a2bc-e84ae9922146 none            swap    sw              0       0
/dev/hda        /media/cdrom0   udf,iso9660 user,noauto,exec 0       0

Koshie-2.0

Re : [Résolu] Disque dur externe mal monté?

Ajoute le !

Je saurais pas trop t'aider j'ai pas beaucoup toucher à fstab, mise à part que pour déclarer une partition en fat16 ou 32 tu écrit vfat.

Compte anonymisé

Re : [Résolu] Disque dur externe mal monté?

Salut

Un petit :
sudo  fdisk  -l
donnerait déjà un peu + d'infos.

@+

LinePo

Re : [Résolu] Disque dur externe mal monté?

pauline@RoGer:~$ sudo fdisk -l

Disque /dev/sda: 120.0 Go, 120034123776 octets
255 heads, 63 sectors/track, 14593 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0x182d14d1

Périphérique Amorce    Début         Fin      Blocs    Id  Système
/dev/sda1   *           1       14264   114575548+  83  Linux
/dev/sda2           14265       14593     2642692+   5  Extended
/dev/sda5           14265       14593     2642661   82  Linux swap / Solaris

Disque /dev/sdb: 500.1 Go, 500107862016 octets
255 heads, 63 sectors/track, 60801 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0x24796452

Périphérique Amorce    Début         Fin      Blocs    Id  Système
/dev/sdb1              21          22       10239    c  W95 FAT32 (LBA)

Petite question. Je vois (du moins, à ce que je comprends), que mon disque dur semble être en FAT32. Or, lorsque je clique droit sur l'icône de mon DDE et que je vais dans Propriétés, il est écrit qu'il est en NTFS...
Est-ce normal???!

Dernière modification par LinePo (Le 19/03/2009, à 18:52)

Compte anonymisé

Re : [Résolu] Disque dur externe mal monté?

Salut

En fait ton DD fait bien 500 Go, mais il existe une partition de 10 Mo qui sert à quoi ?

Ce que tu peux faire :
1) supprimer cette partition

2) créer ta(es) partition(s) de type ext3 (je suppose) si tu n'as qu'ubuntu installé. Sinon il faudra prévoir soit du fat32 pour partager avec Xp soit autre.

Pour ce faire :
depuis un terminal tu tapes :
sudo umount /dev/sdb1
puis
sudo  gparted

Et là tu devrais pouvoir supprimer ta partition de 10 Mo et créer les autres.

Bon courage

@+

LinePo

Re : [Résolu] Disque dur externe mal monté?

Je me demande si c'est vraiment judicieux de supprimer cette partition...
Il semble qu'il y ait un petit fichier Start.exe dedans. J'imagine bien que ce .exe ne me sert pas à grand chose sous Linux, mais je risque de connecter ce DDE à d'autres ordinateurs qui eux, fonctionnent sous Windows (je ne suis pas sous Dualboot).

Qu'en penses-tu?

warlike-elfe

Re : [Résolu] Disque dur externe mal monté?

C'est surement une option de backup intégrée au Disque !

Quelle est la marque et le modèle ? STP

---

« Bravo, vous avez gagné 1 point Godwin.»

LinePo

Re : [Résolu] Disque dur externe mal monté?

C'est un LaCie 500Go (LaCie Desktop Hard Disk 500Go)... Un tout simple, tout bête.

Un petit lien au cas où
http://www.cdiscount.com/informatique/d … &numpage=1

warlike-elfe

Re : [Résolu] Disque dur externe mal monté?

Donc la partition de 10 Mo contient l'exécutable "LaCie Backup Assistant".
(Aucun risque de la supprimer pour l'utilisation de ton disque en tant que .... disque ! Mouaaaa)

A toi de voir si tu compte utiliser cette option ou pas !

Dernière modification par warlike-elfe (Le 24/03/2009, à 18:50)

---

« Bravo, vous avez gagné 1 point Godwin.»

LinePo

Re : [Résolu] Disque dur externe mal monté?

Dans le doute,je dirais, autant garder cette partition et l'exécutable. On sait jamais...
Mais ceci ne règle toujours pas mon problème de détection et/ou montage On sait maintenant que mon ordinateur détecte relativement correctement (je crois) cette partition, mais pas l'autre. Or, c'est l'autre qui m'intéresse un peu plus.

Quelqu'un dans le coin?

warlike-elfe

Re : [Résolu] Disque dur externe mal monté?

sudo fdisk -l ne renseigne qu'une partition sur ton disque.

Demonte le disque :

sudo umount /dev/sdb1

puis lance Gparted avec sudo

Créer la partition sur le reste de ton disque et format en NTFS

Si le formatage de fonctionne pas depuis Gparted

sudo mkntfs /dev/sdb*

---

« Bravo, vous avez gagné 1 point Godwin.»

LinePo

Re : [Résolu] Disque dur externe mal monté?

En effet, le formatage n'a pas fonctionné avec Gparted. Un message d'erreur s'est ouvert

It is not possible to create more than 1 primary partition
If you want more partitions you should first create an extended partition. Such a partition can contain other partitions. Because an extended partition is also a primary partition it might be necessary to remove a primary partition first.

Et ensuite

pauline@RoGer:~$ sudo mkntfs /dev/sdb*
sudo: mkntfs: command not found

Compte anonymisé

Re : [Résolu] Disque dur externe mal monté?

Salut

As-tu déjà créé une partition avec Gparted ? :
sudo gparted puis création nouvelle partition

Si oui peux-tu donner le résultat de :
sudo   fdisk  -l

Ensuite il faudra formater cette partition. Pouquoi en ntfs ???
Je ne vois pas trop l'intérêt.
Je te conseille plutôt un formatage ext3 pour une utilisation pur ubuntu et fat32 pour échange ubuntu Xp.

Tu peux créer 4 partitions sur ton dd (3 en fait si tu gardes la première)

@+

LinePo

Re : [Résolu] Disque dur externe mal monté?

Je viens de réessayer d'ouvrir Gparted.
Cette fois ci, au démarrage du logiciel, une nouvelle partition est détectée (/dev/sdb2) sans que j'ai touché à rien d'autre. Elle s'appelle apparement Setup Assistant et fait bizarrement 10Mo, comme la première partition...
Je comprends plus rien!

J'ai supprimé sdb2, et j'ai réessayé de créer une partition en fat32.
Au moment d'appliquer les changements, voici le message d'erreur qui s'affiche.

An error occured while applying the operations
See the details for more information.

IMPORTANT
If you want support, you need to provide the saved details!
See http://gparted.sourceforge.net/larry/tips/save_details.htm for more information.

Et voilà les détails en question

GParted 0.3.3

Libparted 1.7.1

Create Primary Partition #1 (fat32, 465.76 GiB) on /dev/sdb  00:01    ( ERROR )
     
   create empty partition  00:01    ( ERROR )
   libparted messages    ( INFO )
     
  On ne peut avoir de partitions qui se chevauchent.

  ========================================

Compte anonymisé

Re : [Résolu] Disque dur externe mal monté?

Salut

reprend au post #7 et dans l'ordre :
1) tu supprimes tout sur ce dd
tu valides et tu sorts de geparted

Tu relances Gparted par sudo

2) tu crées au moins 2 partitions primaires :
    une en fat32 100 go par exemple
    une en ext3  tout le reste.

@+

Dernière modification par Compte anonymisé (Le 25/03/2009, à 13:19)

LinePo

Re : [Résolu] Disque dur externe mal monté?

Bon, j'ai créé une partition de 10Mo (la précédente, finalement, n'existe plus) en ext3 et le reste en fat32.
Ca semble marcher pas trop mal, mais la copie des fichiers est toujours impossible. Lorsque la fenêtre de "Progression de la copie de fichiers" s'ouvre, aucune progression, justement. Cela semble être définitivement "En attente"...

Compte anonymisé

Re : [Résolu] Disque dur externe mal monté?

Pourquoi 10 mo sur un disque de 500 go ?
En fait tu ne veux peut être que du fat32 sur ce disque ??

Sinon il faut ensuite monter ta partition pour pouvoir copier des fichiers dessus.

Voir la documentation

@+

Dernière modification par Compte anonymisé (Le 25/03/2009, à 15:21)

Miriad

Re : [Résolu] Disque dur externe mal monté?

Quelqu'un a dit ici qu'il s'agissait d'un executable les petits amis T.T !

Et en effet, sous windows, quand on lance cette executable ... on assiste au.... partitionage ! ^^

Cela dit... gros HIC ! Celui-ci offre soit 500 Giga windows, soit 32Go Linux & Windows + une seconde partition de 468Go non compatible linux .... T.T !

Donc, oui c'est un disque dur bien sympas pour ca taille vis à vis de son prix...

Personnellement je suis pas un fin connaisseur en matière de disque dur externe, mais j'aimerais quand même une plus grande partition lisible sur windows & linux à la fois !!!! Je ne vois pas comment on peut imaginer proposer aux utilisateurs de faire deux partitions comme celles ci... c'est carrément absurde comme compromis >.> ! (sauf en cas de reception d'un petit cheque de la part de microsoft pour rendre windows indispensable au quotidien, évidement T.T)

Donc, en gros, si on veut utiliser ce disque dur sous windows & Linux à la fois, je suppose qu'il doit falloir utiliser un programme linux pour le partitioner. Cela dit, le disque dur étant sous tension (alimentation exterieur), le formater sans l'executable constructeur ne ferait il pas sauter la garantie ainsi que le bon fonctionnement du disque -_-?!
Pour la garantie, à mon avis c'est clair et net. Dommage,  car il est garantie deux ans !:/

Miriad

Re : [Résolu] Disque dur externe mal monté?

J'ai testé le formatage logiciel et finalement 436 Go sont accessibles sous windows et Linux (partition avec 99mo considérés comme utilisés). Cette première partition ne contient qu'un autorun.
Une partition exchange s'est crée, elle contient le guide d'utilisation (total des dossiers placés dessus atteint environ 100 mo) et un exécutable avec 29 Go libre et 148 Go considérés comme utilisés.

Voili, voilà.