Pages : 1
#1 Le 14/06/2006, à 10:56
- totof
Problème disque dur externe en firewire.
Bonjour à tous,
Je possède un Barebone Soltek EQ3401, ainsi qu'un disque externe qui est USB2 et Firewire.
Je viens de passer de Breezy ou tout fonctionnait trés bien à Dapper, ou ce fameux disque ne fonctionne plus en Firewire.
Ce n'est pas la fin du monde, puisque en USB2 ca fonctionne, mais le Firewire, c'est tellement mieux!
Je remonterais la ref du chip Texas qui fait le pont IEEE1394 ce soir... ainsi que celle côté boitier externe.
Merci.
Hors ligne
#2 Le 14/06/2006, à 11:13
- loloemr
Re : Problème disque dur externe en firewire.
branche ton disque, ouvres un terminal et tapes :
dmesgjuste pour voir ce qu'il te dit au branchement.
L'open source est garant de notre indépendance technologique, permet de créer des emplois locaux et véhiculent deux idées fondamentales : la transparence de l'information et la supériorité de la collaboration sur la concurrence ... GNU/Linux c'est bon mangez-en !!
Hors ligne
#3 Le 14/06/2006, à 11:21
- totof
Re : Problème disque dur externe en firewire.
J'ai le type de controleur FireWire.
C'est un Texas FW323 1394A, je pense trés classique.
Pour le dmesg, il faudra attendre ce soir, que je rentre chez moi.
Merci, a tout'
Hors ligne
#4 Le 14/06/2006, à 18:32
- totof
Re : Problème disque dur externe en firewire.
Bon, me revoila:
Donc un lspci me rapporte:
0000:02:0b.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 61)Le dmesg lui me donne:
[4294667.296000] Linux version 2.6.15-23-686 (buildd@rothera) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Tue May 23 14:03:07 UTC 2006
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[4294667.296000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[4294667.296000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[4294667.296000] BIOS-e820: 0000000000100000 - 000000003ff40000 (usable)
[4294667.296000] BIOS-e820: 000000003ff40000 - 000000003ff50000 (ACPI data)
[4294667.296000] BIOS-e820: 000000003ff50000 - 0000000040000000 (ACPI NVS)
[4294667.296000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[4294667.296000] 127MB HIGHMEM available.
[4294667.296000] 896MB LOWMEM available.
[4294667.296000] found SMP MP-table at 000ff780
[4294667.296000] On node 0 totalpages: 261952
[4294667.296000] DMA zone: 4096 pages, LIFO batch:0
[4294667.296000] DMA32 zone: 0 pages, LIFO batch:0
[4294667.296000] Normal zone: 225280 pages, LIFO batch:31
[4294667.296000] HighMem zone: 32576 pages, LIFO batch:7
[4294667.296000] DMI 2.3 present.
[4294667.296000] ACPI: RSDP (v000 ACPIAM ) @ 0x000f6d70
[4294667.296000] ACPI: RSDT (v001 A M I OEMRSDT 0x12000318 MSFT 0x00000097) @ 0x3ff40000
[4294667.296000] ACPI: FADT (v002 A M I OEMFACP 0x12000318 MSFT 0x00000097) @ 0x3ff40200
[4294667.296000] ACPI: MADT (v001 A M I OEMAPIC 0x12000318 MSFT 0x00000097) @ 0x3ff40300
[4294667.296000] ACPI: OEMB (v001 A M I OEMBIOS 0x12000318 MSFT 0x00000097) @ 0x3ff50040
[4294667.296000] ACPI: DSDT (v001 1ABOY 1ABOY000 0x00000000 INTL 0x02002026) @ 0x00000000
[4294667.296000] ACPI: PM-Timer IO Port: 0x808
[4294667.296000] ACPI: Local APIC address 0xfee00000
[4294667.296000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[4294667.296000] Processor #0 15:2 APIC version 20
[4294667.296000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[4294667.296000] Processor #1 15:2 APIC version 20
[4294667.296000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[4294667.296000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[4294667.296000] ACPI: IRQ0 used by override.
[4294667.296000] ACPI: IRQ2 used by override.
[4294667.296000] ACPI: IRQ9 used by override.
[4294667.296000] Enabling APIC mode: Flat. Using 1 I/O APICs
[4294667.296000] Using ACPI (MADT) for SMP configuration information
[4294667.296000] Allocating PCI resources starting at 50000000 (gap: 40000000:bfb80000)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=/dev/hda5 ro quiet splash
[4294667.296000] mapped APIC to ffffd000 (fee00000)
[4294667.296000] mapped IOAPIC to ffffc000 (fec00000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[4294667.296000] Detected 2394.134 MHz processor.
[4294667.296000] Using pmtmr for high-res timesource
[4294667.296000] Console: colour VGA+ 80x25
[4294669.205000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[4294669.206000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[4294669.241000] Memory: 1026520k/1047808k available (2101k kernel code, 20584k reserved, 592k data, 332k init, 130304k highmem)
[4294669.241000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[4294669.301000] Calibrating delay using timer specific routine.. 4791.35 BogoMIPS (lpj=2395677)
[4294669.301000] Security Framework v1.0.0 initialized
[4294669.301000] SELinux: Disabled at boot.
[4294669.301000] Mount-cache hash table entries: 512
[4294669.301000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[4294669.301000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[4294669.301000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[4294669.301000] CPU: L2 cache: 512K
[4294669.301000] CPU: Hyper-Threading is disabled
[4294669.301000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[4294669.301000] mtrr: v2.0 (20020519)
[4294669.301000] Enabling fast FPU save and restore... done.
[4294669.301000] Enabling unmasked SIMD FPU exception support... done.
[4294669.301000] Checking 'hlt' instruction... OK.
[4294669.305000] SMP alternatives: switching to UP code
[4294669.305000] checking if image is initramfs... it is
[4294669.845000] Freeing initrd memory: 6799k freed
[4294669.851000] ACPI: Looking for DSDT ... not found!
[4294669.852000] CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[4294669.852000] SMP alternatives: switching to SMP code
[4294669.853000] Booting processor 1/1 eip 3000
[4294669.863000] Initializing CPU#1
[4294669.924000] Calibrating delay using timer specific routine.. 4787.36 BogoMIPS (lpj=2393683)
[4294669.924000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[4294669.924000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[4294669.924000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[4294669.924000] CPU: L2 cache: 512K
[4294669.924000] CPU: Hyper-Threading is disabled
[4294669.924000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[4294669.924000] CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[4294669.924000] Total of 2 processors activated (9578.72 BogoMIPS).
[4294669.924000] ENABLING IO-APIC IRQs
[4294669.924000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[4294670.035000] checking TSC synchronization across 2 CPUs: passed.
[4294670.036000] Brought up 2 CPUs
[4294670.036000] NET: Registered protocol family 16
[4294670.036000] EISA bus registered
[4294670.036000] ACPI: bus type pci registered
[4294670.036000] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
[4294670.036000] PCI: Using configuration type 1
[4294670.037000] ACPI: Subsystem revision 20051216
[4294670.040000] ACPI: Interpreter enabled
[4294670.040000] ACPI: Using IOAPIC for interrupt routing
[4294670.041000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294670.041000] PCI: Probing PCI hardware (bus 00)
[4294670.043000] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[4294670.043000] PCI quirk: region 0480-04bf claimed by ICH4 GPIO
[4294670.043000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294670.044000] Boot video device is 0000:01:00.0
[4294670.044000] PCI: Transparent bridge - 0000:00:1e.0
[4294670.044000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294670.046000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[4294670.051000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[4294670.051000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[4294670.052000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[4294670.052000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[4294670.052000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[4294670.053000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[4294670.053000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[4294670.053000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[4294670.053000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294670.053000] pnp: PnP ACPI init
[4294670.058000] pnp: PnP ACPI: found 11 devices
[4294670.058000] PnPBIOS: Disabled by ACPI PNP
[4294670.058000] PCI: Using ACPI for IRQ routing
[4294670.058000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[4294670.063000] pnp: 00:09: ioport range 0x680-0x6ff has been reserved
[4294670.063000] pnp: 00:09: ioport range 0x295-0x296 has been reserved
[4294670.063000] PCI: Bridge: 0000:00:01.0
[4294670.063000] IO window: b000-bfff
[4294670.063000] MEM window: fe900000-fe9fffff
[4294670.063000] PREFETCH window: b7f00000-f7efffff
[4294670.063000] PCI: Bridge: 0000:00:1e.0
[4294670.063000] IO window: c000-cfff
[4294670.063000] MEM window: fea00000-feafffff
[4294670.063000] PREFETCH window: disabled.
[4294670.063000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[4294670.064000] audit: initializing netlink socket (disabled)
[4294670.064000] audit(1150307138.062:1): initialized
[4294670.064000] highmem bounce pool size: 64 pages
[4294670.064000] VFS: Disk quotas dquot_6.5.1
[4294670.064000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294670.064000] Initializing Cryptographic API
[4294670.064000] io scheduler noop registered
[4294670.064000] io scheduler anticipatory registered
[4294670.064000] io scheduler deadline registered
[4294670.064000] io scheduler cfq registered
[4294670.065000] isapnp: Scanning for PnP cards...
[4294670.422000] isapnp: No Plug & Play device found
[4294670.446000] Real Time Clock Driver v1.12
[4294670.446000] PNP: No PS/2 controller found. Probing ports directly.
[4294670.448000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294670.448000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294670.448000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[4294670.448000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294670.448000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294670.451000] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294670.451000] 00:05: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294670.452000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294670.452000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294670.452000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294670.452000] mice: PS/2 mouse device common for all mice
[4294670.453000] EISA: Probing bus 0 at eisa.0
[4294670.453000] EISA: Detected 0 cards.
[4294670.453000] NET: Registered protocol family 2
[4294670.466000] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[4294670.466000] TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
[4294670.469000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[4294670.469000] TCP: Hash tables configured (established 262144 bind 65536)
[4294670.469000] TCP reno registered
[4294670.469000] TCP bic registered
[4294670.470000] NET: Registered protocol family 1
[4294670.470000] NET: Registered protocol family 8
[4294670.470000] NET: Registered protocol family 20
[4294670.470000] Starting balanced_irq
[4294670.470000] Using IPI No-Shortcut mode
[4294670.470000] ACPI wakeup devices:
[4294670.470000] P0P4 USB1 USB2 USB3 USB4 EUSB
[4294670.470000] ACPI: (supports S0 S1 S3 S4 S5)
[4294670.470000] Freeing unused kernel memory: 332k freed
[4294670.532000] vga16fb: initializing
[4294670.532000] vga16fb: mapped to 0xc00a0000
[4294670.642000] Console: switching to colour frame buffer device 80x25
[4294670.642000] fb0: VGA16 VGA frame buffer device
[4294671.675000] Capability LSM initialized
[4294672.527000] ICH5: IDE controller at PCI slot 0000:00:1f.1
[4294672.527000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[4294672.527000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
[4294672.527000] ICH5: chipset revision 2
[4294672.527000] ICH5: not 100% native mode: will probe irqs later
[4294672.527000] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
[4294672.527000] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
[4294672.527000] Probing IDE interface ide0...
[4294672.791000] hda: ST360021A, ATA DISK drive
[4294673.403000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294673.406000] Probing IDE interface ide1...
[4294674.078000] hdc: Philips DVD-ROM PCDV632, ATAPI CD/DVD-ROM drive
[4294674.792000] hdd: PIONEER DVD-RW DVR-108, ATAPI CD/DVD-ROM drive
[4294674.844000] ide1 at 0x170-0x177,0x376 on irq 15
[4294674.857000] hda: max request size: 128KiB
[4294674.857000] hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[4294674.857000] hda: cache flushes not supported
[4294674.857000] hda: hda1 hda2 < hda5 hda6 >
[4294674.915000] hdc: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
[4294674.915000] Uniform CD-ROM driver Revision: 3.20
[4294674.926000] hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
[4294675.188000] usbcore: registered new driver usbfs
[4294675.188000] usbcore: registered new driver hub
[4294675.190000] USB Universal Host Controller Interface driver v2.3
[4294675.191000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177
[4294675.191000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294675.191000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[4294675.191000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[4294675.191000] uhci_hcd 0000:00:1d.0: irq 177, io base 0x0000e000
[4294675.191000] hub 1-0:1.0: USB hub found
[4294675.191000] hub 1-0:1.0: 2 ports detected
[4294675.206000] ieee1394: Initialized config rom entry `ip1394'
[4294675.292000] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 185
[4294675.292000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294675.292000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[4294675.292000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[4294675.292000] uhci_hcd 0000:00:1d.1: irq 185, io base 0x0000e400
[4294675.293000] hub 2-0:1.0: USB hub found
[4294675.293000] hub 2-0:1.0: 2 ports detected
[4294675.394000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
[4294675.394000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294675.394000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[4294675.394000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[4294675.394000] uhci_hcd 0000:00:1d.2: irq 169, io base 0x0000e800
[4294675.394000] hub 3-0:1.0: USB hub found
[4294675.394000] hub 3-0:1.0: 2 ports detected
[4294675.495000] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 177
[4294675.495000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[4294675.495000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[4294675.495000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[4294675.495000] uhci_hcd 0000:00:1d.3: irq 177, io base 0x0000ec00
[4294675.495000] hub 4-0:1.0: USB hub found
[4294675.495000] hub 4-0:1.0: 2 ports detected
[4294675.598000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
[4294675.598000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294675.598000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[4294675.598000] ehci_hcd 0000:00:1d.7: debug port 1
[4294675.598000] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[4294675.598000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[4294675.598000] ehci_hcd 0000:00:1d.7: irq 193, io mem 0xfebffc00
[4294675.600000] usb 2-1: new full speed USB device using uhci_hcd and address 2[4294675.602000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[4294675.604000] hub 5-0:1.0: USB hub found
[4294675.604000] hub 5-0:1.0: 8 ports detected
[4294675.705000] ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
[4294675.705000] ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 19 (level, low) -> IRQ 185
[4294675.705000] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
[4294675.758000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185] MMIO=[feafe000-feafe7ff] Max Packet=[2048]
[4294675.856000] Attempting manual resume
[4294675.883000] EXT3-fs: mounted filesystem with ordered data mode.
[4294675.883000] kjournald starting. Commit interval 5 seconds
[4294676.226000] usb 5-4: new high speed USB device using ehci_hcd and address 3[4294676.548000] usb 5-5: new high speed USB device using ehci_hcd and address 4[4294676.875000] usb 2-1: new full speed USB device using uhci_hcd and address 3[4294677.004000] hub 2-1:1.0: USB hub found
[4294677.006000] hub 2-1:1.0: 4 ports detected
[4294677.028000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00601d000a005e50][4294677.283000] usb 2-1.2: new low speed USB device using uhci_hcd and address 4
[4294686.902000] Linux agpgart interface v0.101 (c) Dave Jones
[4294686.907000] agpgart: Detected an Intel 865 Chipset.
[4294686.911000] agpgart: AGP aperture is 64M @ 0xf8000000
[4294687.038000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294687.042000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[4294687.508000] ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 17 (level, low) -> IRQ 201
[4294687.509000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[4294687.560000] usbcore: registered new driver hiddev
[4294687.577000] hw_random: RNG not detected
[4294687.600000] input: KYE Systems Corp. Wireless Keyboard & Mouse as /class/input/input0
[4294687.601000] input: USB HID v1.10 Keyboard [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-1.2
[4294687.640000] input: KYE Systems Corp. Wireless Keyboard & Mouse as /class/input/input1
[4294687.641000] input: USB HID v1.10 Mouse [KYE Systems Corp. Wireless Keyboard & Mouse] on usb-0000:00:1d.1-1.2
[4294687.641000] usbcore: registered new driver usbhid
[4294687.641000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[4294687.665000] input: PC Speaker as /class/input/input2
[4294687.823000] intel8x0_measure_ac97_clock: measured 51732 usecs
[4294687.823000] intel8x0: clocking to 48000
[4294687.905000] SCSI subsystem initialized
[4294687.926000] Initializing USB Mass Storage driver...
[4294687.926000] scsi0 : SCSI emulation for USB Mass Storage devices
[4294687.926000] usb-storage: device found at 3
[4294687.926000] usb-storage: waiting for device to settle before scanning
[4294687.926000] scsi1 : SCSI emulation for USB Mass Storage devices
[4294687.926000] usb-storage: device found at 4
[4294687.926000] usb-storage: waiting for device to settle before scanning
[4294687.926000] usbcore: registered new driver usb-storage
[4294687.926000] USB Mass Storage support registered.
[4294688.118000] FDC 0 is a post-1991 82077
[4294688.191000] ts: Compaq touchscreen protocol output
[4294688.341000] 8139too Fast Ethernet driver 0.9.27
[4294688.341000] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 169
[4294688.341000] eth0: RealTek RTL8139 at 0xf8a80c00, 00:e0:4c:fb:46:0e, IRQ 169[4294688.341000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[4294688.367000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[4294688.592000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[4294688.632000] lp: driver loaded but no devices found
[4294688.675000] sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
[4294688.675000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)[4294688.675000] ieee1394: sbp2: Try serialize_io=0 for better performance
[4294688.758000] Adding 1180736k swap on /dev/hda6. Priority:-1 extents:1 across:1180736k
[4294688.827000] EXT3 FS on hda5, internal journal
[4294689.027000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294689.027000] md: bitmap version 4.39
[4294689.465000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294689.782000] cdrom: open failed.
[4294689.848000] NET: Registered protocol family 17
[4294690.105000] cdrom: open failed.
[4294690.124000] cdrom: open failed.
[4294692.927000] Vendor: ST312002 Model: 6A Rev: 3.06
[4294692.927000] Type: Direct-Access ANSI SCSI revision: 00
[4294692.928000] Vendor: Generic Model: STORAGE DEVICE Rev: 9317
[4294692.928000] Type: Direct-Access ANSI SCSI revision: 00
[4294692.928000] usb-storage: device scan complete
[4294692.928000] Vendor: Generic Model: STORAGE DEVICE Rev: 9317
[4294692.928000] Type: Direct-Access ANSI SCSI revision: 00
[4294692.929000] Vendor: Generic Model: STORAGE DEVICE Rev: 9317
[4294692.929000] Type: Direct-Access ANSI SCSI revision: 00
[4294692.930000] Vendor: Generic Model: STORAGE DEVICE Rev: 9317
[4294692.930000] Type: Direct-Access ANSI SCSI revision: 00
[4294692.934000] usb-storage: device scan complete
[4294693.159000] Driver 'sd' needs updating - please use bus_type methods
[4294693.161000] SCSI device sda: 234441649 512-byte hdwr sectors (120034 MB)
[4294693.161000] sda: assuming drive cache: write through
[4294693.164000] SCSI device sda: 234441649 512-byte hdwr sectors (120034 MB)
[4294693.164000] sda: assuming drive cache: write through
[4294693.164000] sda: sda1
[4294693.170000] sd 0:0:0:0: Attached scsi disk sda
[4294693.173000] sd 1:0:0:0: Attached scsi removable disk sdb
[4294693.177000] sd 1:0:0:1: Attached scsi removable disk sdc
[4294693.181000] sd 1:0:0:2: Attached scsi removable disk sdd
[4294693.185000] sd 1:0:0:3: Attached scsi removable disk sde
[4294693.233000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294693.234000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[4294693.235000] sd 1:0:0:1: Attached scsi generic sg2 type 0
[4294693.235000] sd 1:0:0:2: Attached scsi generic sg3 type 0
[4294693.236000] sd 1:0:0:3: Attached scsi generic sg4 type 0
[4294693.445000] NET: Registered protocol family 10
[4294693.445000] lo: Disabled Privacy Extensions
[4294693.445000] IPv6 over IPv4 tunneling driver
[4294693.522000] sda: Current: sense key: No Sense
[4294693.523000] Additional sense: No additional sense information
[4294704.414000] eth0: no IPv6 routers present
[4294719.278000] ACPI: Power Button (FF) [PWRF]
[4294719.278000] ACPI: Power Button (CM) [PWRB]
[4294719.390000] ibm_acpi: ec object not found
[4294719.417000] pcc_acpi: loading...
[4294722.486000] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[4294722.488000] [fglrx] Maximum main memory to use for locked dma buffers: 927 MBytes.
[4294722.488000] [fglrx] module loaded - fglrx 8.25.18 [May 18 2006] on minor 0
[4294722.819000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177
[4294723.562000] ppdev: user-space parallel port driver
[4294723.819000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[4294723.819000] apm: disabled - APM is not SMP safe.
[4294723.909000] [fglrx] Internal AGP support requested, but kernel AGP support active.
[4294723.909000] [fglrx] Have to use kernel AGP support to avoid conflicts.
[4294723.909000] [fglrx] AGP detected, AgpState = 0x1f004a1b (hardware caps of chipset)
[4294723.910000] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[4294723.910000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[4294723.910000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[4294723.910000] [fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[4294723.921000] [fglrx] total GART = 67108864
[4294723.921000] [fglrx] free GART = 51113984
[4294723.921000] [fglrx] max single GART = 51113984
[4294723.921000] [fglrx] total LFB = 124817408
[4294723.921000] [fglrx] free LFB = 110219264
[4294723.921000] [fglrx] max single LFB = 110219264
[4294723.921000] [fglrx] total Inv = 134217728
[4294723.921000] [fglrx] free Inv = 134217728
[4294723.921000] [fglrx] max single Inv = 134217728
[4294723.921000] [fglrx] total TIM = 0
[4294727.379000] Bluetooth: Core ver 2.8
[4294727.379000] NET: Registered protocol family 31
[4294727.379000] Bluetooth: HCI device and connection manager initialized
[4294727.379000] Bluetooth: HCI socket layer initialized
[4294727.458000] Bluetooth: L2CAP ver 2.8
[4294727.458000] Bluetooth: L2CAP socket layer initialized
[4294727.462000] Bluetooth: RFCOMM socket layer initialized
[4294727.462000] Bluetooth: RFCOMM TTY layer initialized
[4294727.462000] Bluetooth: RFCOMM ver 1.7
[4294734.075000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[4296364.241000] usb 5-4: USB disconnect, address 3
[4296382.456000] ieee1394: The root node is not cycle master capable; selecting a new root node and resetting...
[4296382.714000] ieee1394: Node changed: 0-00:1023 -> 0-01:1023Je compacte ce que concerne l'ohci ieee1394:
[4294675.206000] ieee1394: Initialized config rom entry `ip1394'
[4294675.705000] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
[4294675.758000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[185] MMIO=[feafe000-feafe7ff] Max Packet=[2048]
[4294675.856000] Attempting manual resume
[4294677.028000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00601d000a005e50]
[4294688.675000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)[4294688.675000] ieee1394: sbp2: Try serialize_io=0 for better performance
[4296364.241000] usb 5-4: USB disconnect, address 3
[4296382.456000] ieee1394: The root node is not cycle master capable; selecting a new root node and resetting...
[4296382.714000] ieee1394: Node changed: 0-00:1023 -> 0-01:1023
A la fin, on voit trés bien l'éjection de mon disque en USB2, monté en temps que SDA, et juste aprés, sa détection par le controleur ieee1394...
Mais pas de montage pour autant;'(
Koi k'iss s'passe??????
Hors ligne
#5 Le 14/06/2006, à 18:40
- loloemr
Re : Problème disque dur externe en firewire.
et si tu essaie de le monter à la main ?
sudo mkdir /media/fw_disk
sudo mount /dev/sda1 /media/fw_diskPour le numéro de sda, c'est à toi de voir.
L'open source est garant de notre indépendance technologique, permet de créer des emplois locaux et véhiculent deux idées fondamentales : la transparence de l'information et la supériorité de la collaboration sur la concurrence ... GNU/Linux c'est bon mangez-en !!
Hors ligne
#6 Le 14/06/2006, à 20:25
- totof
Re : Problème disque dur externe en firewire.
Ben non, y'a pas de mount qui tiennes,
Je n'ai pas de /dev/sdx ou /dev/sgx (comme c'était le cas avant) correspondant à ce périph.
Hors ligne
#7 Le 15/06/2006, à 08:23
- totof
Re : Problème disque dur externe en firewire.
Pleazzzzzzzz Help!
Hors ligne
#8 Le 17/06/2006, à 21:45
- totof
Re : Problème disque dur externe en firewire.
Bon, j'ai du nouveau, mais c'est pas gagné.
Aprés pas mal de lecture j'ai installé gscanbus.
J'ai controlé la présence des bons modules, c'est ok!
je lance gscanbus, qui donne dans mon term:
tof@qbic:~$ sudo gscanbus
Error while reading from IEEE1394: : Resource temporarily unavailable
0/0x0000fffff0000400: read failed
0/0x0000fffff0000400: wrong bus info block length
Error while reading from IEEE1394: : Resource temporarily unavailable
0/0x0000fffff0000400: read failed
0/0x0000fffff0000400: wrong bus info block length
dans la fenetre graphique, j'ai un périph inconnu.
si je lance un reset je vois un 'Prolific combo device' et là je suis d'accord.
Le problème c'est que je ne vois toujours pas mon périph.
dmesg rapporte des insultes:
[17181511.384000] command: Test Unit Ready: 00 00 00 00 00 00
[17181511.384000] ieee1394: sbp2: reset requested
[17181511.384000] ieee1394: sbp2: Generating sbp2 fetch agent reset
[17181531.388000] ieee1394: sbp2: aborting sbp2 command
[17181531.388000] 7:0:0:0:
[17181531.388000] command: Test Unit Ready: 00 00 00 00 00 00
[17181531.388000] 7:0:0:0: scsi: Device offlined - not ready after error recovery
[17181531.388000] ieee1394: sbp2: scsi_add_device failed (-19)
Hors ligne