Ubuntu-fr

bysontin

carte pctv rave changee de slot ide... marche plus :'(

Bonjour,

Je vous explique mon pb :
J'ai dernièrement acheté un nouveau boitier (mon pc chauffait trop avec l'ancien... bref, c'est pas ce qui nous interesse). Je bouge donc tout mon matos vers le nouveau boitier... j'alume le pc... ok, tout marche bien sauf la carte télé :'(

j'ai essayé de desinstaller et reinstaller le module bttv et bt787 ca n'a rien fait. Quand je lance tvtime, je capte aucun signal, alors qu'avant de changer le boitier, tvtime marchait nikel.

Le problème vient peut-etre du fait que j'ai changé ma carte de slot pci ?

un lspci me donne :

0000:01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)

un lsmod | grep bttv me donne :

bttv                  164304  1 bt878
video_buf              22148  1 bttv
i2c_algo_bit            9608  1 bttv
v4l2_common             6016  1 bttv
btcx_risc               5128  1 bttv
tveeprom               15248  1 bttv
videodev                9856  1 bttv
i2c_core               21904  11 bttv,i2c_algo_bit,tveeprom,i2c_acpi_ec,asb100,eeprom,lm90,tuner,tda9887,nvidia,i2c_nforce2

et un dmesg | grep bttv :

[17179589.680000] bttv: driver version 0.9.16 loaded
[17179589.680000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[17179589.680000] bttv: Bt8xx card found (0).
[17179589.680000] bttv0: Bt878 (rev 17) at 0000:01:0a.0, irq: 217, latency: 32, mmio: 0xd8000000
[17179589.680000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[17179589.680000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[17179589.680000] bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init]
[17179589.684000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17179589.684000] bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no
[17179589.684000] bttv0: using tuner=33
[17179589.684000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17179589.688000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[17179589.688000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[17179589.900000] bttv0: registered device video0
[17179589.900000] bttv0: registered device vbi0
[17179589.900000] bttv0: PLL: 28636363 => 35468950 ..eth0: no link during initialization.
[17180384.860000] bttv0: unloading
[17180461.628000] bttv: driver version 0.9.16 loaded
[17180461.628000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[17180461.628000] bttv: Bt8xx card found (0).
[17180461.628000] bttv0: Bt878 (rev 17) at 0000:01:0a.0, irq: 217, latency: 32, mmio: 0xd8000000
[17180461.628000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[17180461.628000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[17180461.628000] bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init]
[17180461.776000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17180461.780000] bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no
[17180461.780000] bttv0: using tuner=33
[17180461.868000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17180461.872000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[17180461.876000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[17180461.892000] bttv0: registered device video0
[17180461.892000] bttv0: registered device vbi0
[17180461.892000] bttv0: PLL: 28636363 => 35468950 . ok
[17180822.268000] bttv0: unloading
[17180838.480000] bttv: driver version 0.9.16 loaded
[17180838.480000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[17180838.480000] bttv: Bt8xx card found (0).
[17180838.480000] bttv0: Bt878 (rev 17) at 0000:01:0a.0, irq: 217, latency: 32, mmio: 0xd8000000
[17180838.480000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[17180838.480000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[17180838.480000] bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init]
[17180838.712000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17180838.712000] bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no
[17180838.712000] bttv0: using tuner=33
[17180838.784000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[17180838.784000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[17180838.788000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[17180838.808000] bttv0: registered device video0
[17180838.812000] bttv0: registered device vbi0

si qqun a une idée du problème, un peu d'aide serait le bienvenue...

Merci !