Ubuntu-fr

yorg

problèmes avec une 9600se

bonjour
J'ai des problèmes avec l'acceleration 3d avec ma 9600se.
J'ai essayer d'utiliser les drivers ai des depots mais meme si j'obtenias l'acceleration, j'avais des scores faibles a fgl_glxgears et glxgears (environ 250fps).
Donc j'ai essayé d'installer les drivers libres avec le tuto puis des methodes trouver sur le forum mais je ne parviens pas à avoir l'accéleration 3d

direct rendering: No

voici mon fichier xorg.conf:

# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
	FontPath	"/usr/share/X11/fonts/misc"
	FontPath	"/usr/share/X11/fonts/cyrillic"
	FontPath	"/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/Type1"
	FontPath	"/usr/share/X11/fonts/100dpi"
	FontPath	"/usr/share/X11/fonts/75dpi"
	FontPath	"/usr/share/fonts/X11/misc"
	# path to defoma fonts
	FontPath	"/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load	"i2c"
	Load	"bitmap"
	Load	"ddc"
	Load	"dri"
	Load	"extmod"
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"fr"
	Option		"XkbOptions"	"lv3:ralt_switch"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ExplorerPS/2"
	Option		"ZAxisMapping"		"4 5"
	Option		"Emulate3Buttons"	"true"
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "stylus"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "stylus"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "eraser"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "eraser"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "cursor"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "cursor"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies, Inc. RV350 AQ [Radeon 9600 SE]"
	Driver		"radeon"
	BusID		"PCI:1:0:0"
        Option          "AGPMode"               "4"
        Option          "AGPSize"               "128"
        Option          "RingSize"              "8"
        Option          "BufferSize"            "2"
        Option          "EnablePageFlip"        "true"
        Option          "EnableDepthMoves"      "true"
        Option          "ColorTiling"           "on"

        Option          "RenderAccel"           "true"
        Option          "DRI"                   "true"
EndSection

Section "Monitor"
	Identifier	"LS704U"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies, Inc. RV350 AQ [Radeon 9600 SE]"
	Monitor		"LS704U"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"
	InputDevice     "stylus" "SendCoreEvents"
	InputDevice     "cursor" "SendCoreEvents"
	InputDevice     "eraser" "SendCoreEvents"
        Option          "AIGLX" "true"
EndSection

Section "DRI"
	Mode	0666
EndSection

Section "Extensions"
    Option "Composite" "Enable"
EndSection

yorg

Re : problèmes avec une 9600se

suite à un plantage de x à cause de tests au niveau de xorg.conf j'ai dut revenir à une ancienne version xorg.conf  et la surprise ca marche mieu j'ai apparement l'acceleration 3d et un score de 1000fps environ a glxgears et beryl fonctionne relativement bien (un peu lent et gourmand en ressources cpu). Mais ils doit rester des problèmes car par exemple dans planet penguin racer l'affichage deconne et le jeux tourne a 25 fps .
De plus j'ai ceci:

adrien@adrien-desktop:~$  glxinfo | grep rendering
libGL warning: 3D driver claims to not support visual 0x4b
direct rendering: Yes

mon nouveau xorg.conf est:

Section "Files"
	FontPath	"/usr/share/X11/fonts/misc"
	FontPath	"/usr/share/X11/fonts/cyrillic"
	FontPath	"/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/Type1"
	FontPath	"/usr/share/X11/fonts/100dpi"
	FontPath	"/usr/share/X11/fonts/75dpi"
	FontPath	"/usr/share/fonts/X11/misc"
	# path to defoma fonts
	FontPath	"/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load	"i2c"
	Load	"bitmap"
	Load	"ddc"
	Load	"dri"
	Load	"extmod"
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"fr"
	Option		"XkbOptions"	"lv3:ralt_switch"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ExplorerPS/2"
	Option		"ZAxisMapping"		"4 5"
	Option		"Emulate3Buttons"	"true"
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "stylus"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "stylus"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "eraser"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "eraser"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "cursor"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "cursor"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies, Inc. RV350 AQ [Radeon 9600 SE]"
	Driver		"radeon"
	BusID		"PCI:1:0:0"
EndSection

Section "Monitor"
	Identifier	"LS704U"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies, Inc. RV350 AQ [Radeon 9600 SE]"
	Monitor		"LS704U"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"
	InputDevice     "stylus" "SendCoreEvents"
	InputDevice     "cursor" "SendCoreEvents"
	InputDevice     "eraser" "SendCoreEvents"
EndSection

Section "DRI"
	Mode	0666
EndSection

Donc je suppose que le problème vient des options dans device car c'est la seule difference entre l'ancien et le nouveau xorg.conf mais je ne sais pas trop comment le regler (j'avais recupere les options d'un xorg.conf de 9600 mais apparement le fait que se soit une 9600se change les options à mettre.

si quelqun pouvait m'aider ca serait simpa

yorg

Re : problèmes avec une 9600se

personne n'a d'idées?