Clé USB non reconnue

Thysandher · Le 13/12/2006, à 15:03

Bonjour !

J'ai un problème avec ma clé USB qui n'est plus montée correctement, et pourtant elle l'était lorsque j'ai installé Kubuntu Edgy Eft ( ma premiere distri linux ). Depuis la mise à jour que j'ai faite la semaine derniere, je n'arrive plus à la faire fonctionner ( je la branche mais rien ne se passe ). J'ai lu plusieurs posts sur les clés USB et sur le prob avec HAL ( qui est chez moi en version 0.5.7.1-0Ubuntu17 ), et j'ai aussi essayé la commande lusb qui ne donne rien ( bash : commande lusb introuvable ).
Ma clé est de marque Imation et fait 1 Go ( je répete : elle marchait avant la mise à jour. ).
J'ai

Si une âme charitable pouvait m'aider ça serait sympa !

benjou · Le 13/12/2006, à 15:14

lusb c' est lsusb

essaie aussi dmesg apres avoir insère la cle et poste nous les 10-20 dernières lignes.

Thysandher · Le 13/12/2006, à 15:22

Bon j'ai fait lsusb deux fois : une fois alors qu'elle était débranchée et une autre alors qu'elle était branchée.

thysandher@Kubuntu:~$ lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
thysandher@Kubuntu:~$ lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 003: ID 1307:0163
Bus 001 Device 001: ID 0000:0000

et voila pour dmesg

thysandher@Kubuntu:~$ dmesg
[17179569.184000] Linux version 2.6.17-10-generic (root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubun
tu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[17179569.184000]  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[17179569.184000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 511MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f66c0
[17179569.184000] On node 0 totalpages: 131056
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   Normal zone: 126960 pages, LIFO batch:31
[17179569.184000] DMI 2.2 present.
[17179569.184000] ACPI: RSDP (v000 VIA694                                ) @ 0x000f80c0

C'est grave docteur ? :D

Thysandher · Le 13/12/2006, à 15:42

Je viens de me rendre compte que c'etait les 20 dernieres et non les 20 premieres :

[17180274.372000] usb 1-2: new full speed USB device using uhci_hcd and address 2
[17180274.544000] usb 1-2: configuration #1 chosen from 1 choice
[17180274.744000] usbcore: registered new driver libusual
[17180274.872000] SCSI subsystem initialized
[17180274.876000] Initializing USB Mass Storage driver...
[17180274.880000] scsi0 : SCSI emulation for USB Mass Storage devices
[17180274.880000] usbcore: registered new driver usb-storage
[17180274.880000] USB Mass Storage support registered.
[17180274.880000] usb-storage: device found at 2
[17180274.880000] usb-storage: waiting for device to settle before scanning
[17180279.884000] usb-storage: device scan complete
[17180279.888000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 0.00
[17180279.888000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[17180279.964000] SCSI device sda: 2015231 512-byte hdwr sectors (1032 MB)
[17180279.968000] sda: Write Protect is off
[17180279.968000] sda: Mode Sense: 00 00 00 00
[17180279.968000] sda: assuming drive cache: write through
[17180279.984000] SCSI device sda: 2015231 512-byte hdwr sectors (1032 MB)
[17180279.984000] sda: Write Protect is off
[17180279.984000] sda: Mode Sense: 00 00 00 00
[17180279.984000] sda: assuming drive cache: write through
[17180279.984000]  sda: sda1
[17180280.104000] sd 0:0:0:0: Attached scsi removable disk sda
[17180280.128000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[17180422.568000] usb 1-2: USB disconnect, address 2
[17181936.968000] usb 1-2: new full speed USB device using uhci_hcd and address 3
[17181937.132000] usb 1-2: configuration #1 chosen from 1 choice
[17181937.136000] scsi1 : SCSI emulation for USB Mass Storage devices
[17181937.136000] usb-storage: device found at 3
[17181937.136000] usb-storage: waiting for device to settle before scanning
[17181942.136000] usb-storage: device scan complete
[17181942.140000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 0.00
[17181942.140000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[17181942.156000] SCSI device sda: 2015231 512-byte hdwr sectors (1032 MB)
[17181942.160000] sda: Write Protect is off
[17181942.160000] sda: Mode Sense: 00 00 00 00
[17181942.160000] sda: assuming drive cache: write through
[17181942.172000] SCSI device sda: 2015231 512-byte hdwr sectors (1032 MB)
[17181942.176000] sda: Write Protect is off
[17181942.176000] sda: Mode Sense: 00 00 00 00
[17181942.176000] sda: assuming drive cache: write through
[17181942.176000]  sda: sda1
[17181942.292000] sd 1:0:0:0: Attached scsi removable disk sda
[17181942.292000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[17182681.676000] usb 1-2: USB disconnect, address 3

Et voila !

Thysandher · Le 15/12/2006, à 11:55

UUUUUP !
Je fais quoi maintenant ?

benjou · Le 15/12/2006, à 13:28

Ben t'es dans la...

Ton dmesg finit par usb 1-2: USB disconnect, address 3

Voila comment finit mon dmesg quand j'insere une cle usb

[17184570.096000] usb 5-8: new high speed USB device using ehci_hcd and address 4
[17184570.240000] usb 5-8: configuration #1 chosen from 1 choice
[17184570.240000] hub 5-8:1.0: USB hub found
[17184570.240000] hub 5-8:1.0: 1 port detected
[17184570.544000] usb 5-8.1: new high speed USB device using ehci_hcd and address 5
[17184570.648000] usb 5-8.1: configuration #1 chosen from 1 choice
[17184570.880000] usbcore: registered new driver libusual
[17184570.968000] Initializing USB Mass Storage driver...
[17184570.968000] scsi2 : SCSI emulation for USB Mass Storage devices
[17184570.968000] usb-storage: device found at 5
[17184570.968000] usb-storage: waiting for device to settle before scanning
[17184570.968000] usbcore: registered new driver usb-storage
[17184570.968000] USB Mass Storage support registered.
[17184575.968000] usb-storage: device scan complete
[17184575.968000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 1.00
[17184575.968000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[17184575.984000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17184575.988000] sdb: Write Protect is off
[17184575.988000] sdb: Mode Sense: 00 26 00 00
[17184575.988000] sdb: assuming drive cache: write through
[17184575.992000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17184575.996000] sdb: Write Protect is off
[17184575.996000] sdb: Mode Sense: 00 26 00 00
[17184575.996000] sdb: assuming drive cache: write through
[17184575.996000]  sdb: sdb1
[17184575.996000] sd 2:0:0:0: Attached scsi removable disk sdb
[17184575.996000] sd 2:0:0:0: Attached scsi generic sg2 type 0
[17184576.776000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[17184634.620000] usb 5-8: USB disconnect, address 4
[17184634.620000] usb 5-8.1: USB disconnect, address 5
[17184803.700000] usb 5-8: new high speed USB device using ehci_hcd and address 6
[17184803.844000] usb 5-8: configuration #1 chosen from 1 choice
[17184803.844000] hub 5-8:1.0: USB hub found
[17184803.844000] hub 5-8:1.0: 1 port detected
[17184804.148000] usb 5-8.1: new high speed USB device using ehci_hcd and address 7
[17184804.252000] usb 5-8.1: configuration #1 chosen from 1 choice
[17184804.252000] scsi3 : SCSI emulation for USB Mass Storage devices
[17184804.252000] usb-storage: device found at 7
[17184804.252000] usb-storage: waiting for device to settle before scanning
[17184809.252000] usb-storage: device scan complete
[17184809.252000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 1.00
[17184809.252000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[17184809.260000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17184809.260000] sdb: Write Protect is off
[17184809.260000] sdb: Mode Sense: 00 26 00 00
[17184809.260000] sdb: assuming drive cache: write through
[17184809.268000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17184809.272000] sdb: Write Protect is off
[17184809.272000] sdb: Mode Sense: 00 26 00 00
[17184809.272000] sdb: assuming drive cache: write through
[17184809.272000]  sdb: sdb1
[17184809.272000] sd 3:0:0:0: Attached scsi removable disk sdb
[17184809.272000] sd 3:0:0:0: Attached scsi generic sg2 type 0
[17184810.232000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[17184831.936000] usb 5-8: USB disconnect, address 6
[17184831.936000] usb 5-8.1: USB disconnect, address 7
[17191555.536000] usb 5-8: new high speed USB device using ehci_hcd and address 8
[17191555.680000] usb 5-8: configuration #1 chosen from 1 choice
[17191555.680000] hub 5-8:1.0: USB hub found
[17191555.680000] hub 5-8:1.0: 1 port detected
[17191555.984000] usb 5-8.1: new high speed USB device using ehci_hcd and address 9
[17191556.088000] usb 5-8.1: configuration #1 chosen from 1 choice
[17191556.088000] scsi4 : SCSI emulation for USB Mass Storage devices
[17191556.088000] usb-storage: device found at 9
[17191556.088000] usb-storage: waiting for device to settle before scanning
[17191561.088000] usb-storage: device scan complete
[17191561.088000]   Vendor: USB 2.0   Model: Flash Disk        Rev: 1.00
[17191561.088000]   Type:   Direct-Access                      ANSI SCSI revision: 00
[17191561.096000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17191561.100000] sdb: Write Protect is off
[17191561.100000] sdb: Mode Sense: 00 26 00 00
[17191561.100000] sdb: assuming drive cache: write through
[17191561.108000] SCSI device sdb: 2031616 512-byte hdwr sectors (1040 MB)
[17191561.108000] sdb: Write Protect is off
[17191561.108000] sdb: Mode Sense: 00 26 00 00
[17191561.108000] sdb: assuming drive cache: write through
[17191561.108000]  sdb: sdb1
[17191561.112000] sd 4:0:0:0: Attached scsi removable disk sdb
[17191561.112000] sd 4:0:0:0: Attached scsi generic sg2 type 0
[17191564.384000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

on voit que mon systeme scanne l'address 4 et 5, se disconnect, puis passe a 6 et 7, se disconnect puis enfin scanne 8 et 9 et reste connecté.

Je ne sais pas du tout se que ca veut dire...

bon pour la forme je te propose ces dignostiques:

pmount /dev/sda

(montage manuel de ta clé) et regarde si il y a un message d'erreur..

Sinon, tu peux essayer de reformater ta clé...

sinon je ne sais pas...

Dernière modification par benjou (Le 15/12/2006, à 13:28)

Thysandher · Le 17/12/2006, à 09:06

Ca y est ça marche !!! J'ai réussi à la faire remarcher !
En fait il suffit de suivre la procédure donnée dans la doc : http://doc.ubuntu-fr.org/materiel/reparer_cle_usb
( attention : formater en vfat ). Ensuite pour ne pas être obligé de monter le média en sudo, il faut aller dans Reglages du systeme > Avancé > Disques et systèmes de fichiers
Il faut ensuite selectionner le montage /media/usbdisk et le modifier afin que chacun puisse monter / démonter le périphérique ( pas seulement root ). Enfin, en insérant la clé, la petite fenetre s'affiche à nouveau et je peux l'utiliser. J'arrive à copier les fichiers sans problèmes ( sauf permissions ).

Par contre , je n'arrive pas à effacer les fichiers inscrits il me mets "Impossible d'écrire sans le fichier /media/usbdisk/.Trash-1000/info/<nom du fichier>.trashinfo.

Ce n'est donc toujours pas résolu mais on avance

Thysandher · Le 17/12/2006, à 09:09

Quand je fais pmount il m'inscris :

thysandher@Kubuntu:~$ pmount /dev/sda
mount: Aucun medium trouvé
mount: Aucun medium trouvé
thysandher@Kubuntu:~$ pmount /dev/sda1
mount: périphérique spécial /dev/sda1 n'existe pas

fenlabise · Le 23/12/2006, à 07:20

Bonjour,
J'ai le même problème, je n'arrive pas à accéder à ma clé usb et quand je la mets sur le port usb, il me crée
un périphérique /dev/sdc et
un répertoire /media/usbdisk-1

Puis je débranche et je rebranche : il me crée
un périphérique /dev/sdd et
un répertoire /media/usbdisk-2

et ainsi de suite ... !!!

Comme l'indique Thysandher je suis allé sur le site http://doc.ubuntu-fr.org/materiel/reparer_cle_usb

mais ça n'a abouti à rien !
comme tu dis, pour pouvoir lire ou écrire sur la clé usb il faut la formater mais pour la formater, il faut pouvoir y accéder : c'est un cercle vicieux.
Comment faire, merci pour votre aide.

Thysandher · Le 23/12/2006, à 13:28

Pour la formater, je suis pas sur, mais je crois qu'ils le disent dans la doc. Sinon tu as plusieurs options :
-la formater sous windows ( poste de travail ou Gestion des disques )
-la formater avec QTParted

fenlabise · Le 23/12/2006, à 20:55

Bonjour,
Pour la clef USB,
Je l'ai donc formatée : OK
J'ai pu copier des fichiers dessus : OK
Le but est donc atteint...
Mais ce qui me gène, c'est que les "enchères" continuent : j'en suis arrivé à
/dev/sde pour le périphérique et
/media/usbdisk-3 pour le répertoire de stockage

alors qu'il est bien spécifié dans mon fichier fstab
/dev/sdb /media/usbdisk

Tout ça pour être logique.
Merci pour la réponse.

Thysandher · Le 24/12/2006, à 11:22

Essaye voir de taper lsusb et dmesg comme je l'ai fait, comme ça peut-être que quelqu'un pourra t'aider un peu plus ( moi je suis encore un "noob" à Ubuntu ).:)

fenlabise · Le 26/12/2006, à 02:03

Bonjour,
voici le résultat de lsusb :

Bus 003 Device 008: ID 0ea0:2168 Ours Technology, Inc. Transcend JetFlash 2.0 / Astone USB Drive
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000

et le résultat de dmesg :

[17179569.184000] Linux version 2.6.15-27-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Sat Sep 16 01:51:59 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
[17179569.184000]  BIOS-e820: 000000000bff0000 - 000000000bff8000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000000bff8000 - 000000000c000000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 191MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000fbc70
[17179569.184000] On node 0 totalpages: 49136
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 45040 pages, LIFO batch:7
[17179569.184000]   HighMem zone: 0 pages, LIFO batch:0
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 AMI                                   ) @ 0x000faa60
[17179569.184000] ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0bff0000
[17179569.184000] ACPI: FADT (v001 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x0bff0030
[17179569.184000] ACPI: MADT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0bff00c0
[17179569.184000] ACPI: DSDT (v001    SiS      746 0x00000100 INTL 0x02002024) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:3 APIC version 16
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 10000000 (gap: 0c000000:f2c00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda3 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 1024 (order: 10, 16384 bytes)
[17179569.184000] Detected 852.206 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.544000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179570.544000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[17179570.560000] Memory: 184372k/196544k available (1976k kernel code, 11648k reserved, 606k data, 288k init, 0k highmem)
[17179570.560000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179570.640000] Calibrating delay using timer specific routine.. 1705.83 BogoMIPS (lpj=3411670)
[17179570.640000] Security Framework v1.0.0 initialized
[17179570.640000] SELinux:  Disabled at boot.
[17179570.640000] Mount-cache hash table entries: 512
[17179570.640000] CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000
[17179570.640000] CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000
[17179570.640000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179570.640000] CPU: L2 Cache: 64K (64 bytes/line)
[17179570.640000] CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000420 00000000 00000000 00000000
[17179570.640000] mtrr: v2.0 (20020519)
[17179570.640000] CPU: AMD Duron(tm)  stepping 01
[17179570.640000] Enabling fast FPU save and restore... done.
[17179570.640000] Checking 'hlt' instruction... OK.
[17179570.656000] checking if image is initramfs... it is
[17179571.920000] Freeing initrd memory: 6617k freed
[17179571.944000] ACPI: Looking for DSDT ... not found!
[17179571.944000] ENABLING IO-APIC IRQs
[17179571.944000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179572.088000] NET: Registered protocol family 16
[17179572.088000] EISA bus registered
[17179572.088000] ACPI: bus type pci registered
[17179572.088000] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
[17179572.088000] PCI: Using configuration type 1
[17179572.088000] ACPI: Subsystem revision 20051216
[17179572.100000] ACPI: Interpreter enabled
[17179572.100000] ACPI: Using IOAPIC for interrupt routing
[17179572.100000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.100000] PCI: Probing PCI hardware (bus 00)
[17179572.104000] Uncovering SIS963 that hid as a SIS503 (compatible=0)
[17179572.104000] Enabling SiS 96x SMBus.
[17179572.104000] Boot video device is 0000:01:00.0
[17179572.104000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179572.144000] ACPI: Power Resource [URP1] (off)
[17179572.144000] ACPI: Power Resource [URP2] (off)
[17179572.144000] ACPI: Power Resource [FDDP] (off)
[17179572.144000] ACPI: Power Resource [LPTP] (off)
[17179572.144000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[17179572.144000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179572.144000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179572.148000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179572.148000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179572.148000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179572.148000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179572.148000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[17179572.148000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179572.148000] pnp: PnP ACPI init
[17179572.156000] pnp: PnP ACPI: found 13 devices
[17179572.156000] PnPBIOS: Disabled by ACPI PNP
[17179572.156000] PCI: Using ACPI for IRQ routing
[17179572.156000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179572.160000] PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
[17179572.160000] PCI: Bridge: 0000:00:01.0
[17179572.160000]   IO window: b000-bfff
[17179572.160000]   MEM window: cfd00000-cfefffff
[17179572.160000]   PREFETCH window: bfa00000-cfbfffff
[17179572.164000] audit: initializing netlink socket (disabled)
[17179572.164000] audit(1166270630.164:1): initialized
[17179572.164000] VFS: Disk quotas dquot_6.5.1
[17179572.164000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179572.164000] Initializing Cryptographic API
[17179572.164000] io scheduler noop registered
[17179572.164000] io scheduler anticipatory registered
[17179572.164000] io scheduler deadline registered
[17179572.164000] io scheduler cfq registered
[17179572.164000] isapnp: Scanning for PnP cards...
[17179572.516000] isapnp: No Plug & Play device found
[17179572.548000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[17179572.548000] Failed to disable AUX port, but continuing anyway... Is this a SiS?
[17179572.548000] If AUX port is really absent please use the 'i8042.noaux' option.
[17179572.560000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179572.560000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179572.560000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179572.560000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179572.560000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179572.564000] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179572.564000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179572.564000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179572.564000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179572.564000] mice: PS/2 mouse device common for all mice
[17179572.568000] EISA: Probing bus 0 at eisa.0
[17179572.568000] EISA: Detected 0 cards.
[17179572.568000] NET: Registered protocol family 2
[17179572.604000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179572.608000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[17179572.608000] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[17179572.608000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[17179572.608000] TCP: Hash tables configured (established 8192 bind 8192)
[17179572.608000] TCP reno registered
[17179572.608000] TCP bic registered
[17179572.608000] NET: Registered protocol family 1
[17179572.608000] NET: Registered protocol family 8
[17179572.608000] NET: Registered protocol family 20
[17179572.608000] Using IPI Shortcut mode
[17179572.608000] ACPI wakeup devices:
[17179572.608000] PCI0 PS2M PS2K UAR1 USB1 USB2 EHCI  LAN  MDM  AUD
[17179572.608000] ACPI: (supports S0 S1 S4 S5)
[17179572.608000] Freeing unused kernel memory: 288k freed
[17179572.736000] vga16fb: initializing
[17179572.736000] vga16fb: mapped to 0xc00a0000
[17179572.840000] Console: switching to colour frame buffer device 80x25
[17179572.840000] fb0: VGA16 VGA frame buffer device
[17179573.948000] Capability LSM initialized
[17179575.424000] SIS5513: IDE controller at PCI slot 0000:00:02.5
[17179575.424000] SIS5513: chipset revision 0
[17179575.424000] SIS5513: not 100% native mode: will probe irqs later
[17179575.424000] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[17179575.424000]     ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[17179575.424000]     ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
[17179575.424000] Probing IDE interface ide0...
[17179575.712000] hda: Maxtor 6E040L0, ATA DISK drive
[17179576.384000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179576.400000] Probing IDE interface ide1...
[17179577.140000] hdc: ��������������������, ATAPI UNKNOWN (type 31) drive
[17179577.476000] hdc: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
[17179577.476000] hdc: set_drive_speed_status: error=0x04 { AbortedCommand }
[17179577.476000] ide1 at 0x170-0x177,0x376 on irq 15
[17179577.488000] hda: max request size: 128KiB
[17179577.496000] hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
[17179577.496000] hda: cache flushes supported
[17179577.496000]  hda: hda1 hda2 < hda5 hda6 > hda3
[17179577.948000] usbcore: registered new driver usbfs
[17179577.948000] usbcore: registered new driver hub
[17179577.952000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179577.952000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 169
[17179577.952000] ohci_hcd 0000:00:03.0: OHCI Host Controller
[17179577.968000] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[17179577.968000] ohci_hcd 0000:00:03.0: irq 169, io mem 0xcfff9000
[17179578.024000] hub 1-0:1.0: USB hub found
[17179578.024000] hub 1-0:1.0: 3 ports detected
[17179578.128000] ACPI: PCI Interrupt 0000:00:03.1[b] -> GSI 21 (level, low) -> IRQ 177
[17179578.128000] ohci_hcd 0000:00:03.1: OHCI Host Controller
[17179578.144000] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[17179578.144000] ohci_hcd 0000:00:03.1: irq 177, io mem 0xcfffa000
[17179578.200000] hub 2-0:1.0: USB hub found
[17179578.200000] hub 2-0:1.0: 3 ports detected
[17179578.304000] ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) -> IRQ 185
[17179578.304000] ehci_hcd 0000:00:03.2: EHCI Host Controller
[17179578.304000] PCI: cache line size of 64 is not supported by device 0000:00:03.2
[17179578.308000] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[17179578.308000] ehci_hcd 0000:00:03.2: irq 185, io mem 0xcfffb000
[17179578.308000] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179578.308000] hub 3-0:1.0: USB hub found
[17179578.308000] hub 3-0:1.0: 6 ports detected
[17179578.572000] Attempting manual resume
[17179578.596000] EXT3-fs: INFO: recovery required on readonly filesystem.
[17179578.596000] EXT3-fs: write access will be enabled during recovery.
[17179583.448000] EXT3-fs: recovery complete.
[17179583.448000] kjournald starting.  Commit interval 5 seconds
[17179583.448000] EXT3-fs: mounted filesystem with ordered data mode.
[17179595.380000] i2c-sis96x version 1.0.0
[17179595.380000] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[17179595.732000] Real Time Clock Driver v1.12
[17179595.740000] Linux agpgart interface v0.101 (c) Dave Jones
[17179595.748000] agpgart: Detected SiS 741 chipset
[17179595.756000] agpgart: AGP aperture is 64M @ 0xd0000000
[17179596.300000] logips2pp: Detected unknown logitech mouse model 99
[17179596.324000] input: PC Speaker as /class/input/input1
[17179596.380000] Floppy drive(s): fd0 is 1.44M
[17179596.400000] FDC 0 is a post-1991 82077
[17179596.404000] sis900.c: v1.08.09 Sep. 19 2005
[17179596.404000] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 193
[17179596.408000] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[17179596.420000] 0000:00:04.0: Using transceiver found at address 1 as default
[17179596.420000] eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 193, 00:13:8f:2f:8a:bb.
[17179596.432000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179596.436000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179596.788000] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2
[17179597.052000] irda_init()
[17179597.052000] NET: Registered protocol family 23
[17179597.232000] parport: PnPBIOS parport detected.
[17179597.232000] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[17179597.696000] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 201
[17179597.980000] ts: Compaq touchscreen protocol output
[17179598.012000] intel8x0_measure_ac97_clock: measured 55750 usecs
[17179598.012000] intel8x0: clocking to 48000
[17179598.772000] lp0: using parport0 (interrupt-driven).
[17179598.904000] Adding 562232k swap on /dev/hda6.  Priority:-1 extents:1 across:562232k
[17179599.056000] EXT3 FS on hda3, internal journal
[17179599.360000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179599.360000] md: bitmap version 4.39
[17179600.120000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179601.360000] eth0: Media Link On 10mbps half-duplex
[17179603.116000] ACPI: Power Button (FF) [PWRF]
[17179603.116000] ACPI: Power Button (CM) [PWRB]
[17179603.348000] ibm_acpi: ec object not found
[17179603.408000] pcc_acpi: loading...
[17179604.276000] powernow: No powernow capabilities detected
[17179604.620000] NET: Registered protocol family 10
[17179604.620000] lo: Disabled Privacy Extensions
[17179604.620000] IPv6 over IPv4 tunneling driver
[17179611.532000] ppdev: user-space parallel port driver
[17179611.988000] apm: BIOS not found.
[17179615.408000] eth0: no IPv6 routers present
[17207898.104000] ohci_hcd 0000:00:03.0: wakeup
[17207898.488000] usb 1-1: new full speed USB device using ohci_hcd and address 2
[17207899.064000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17207899.064000] usbcore: registered new driver usblp
[17207899.064000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17216477.524000] usb 1-1: USB disconnect, address 2
[17216477.524000] drivers/usb/class/usblp.c: usblp0: removed
[17249851.260000] ibm_acpi: ec object not found
[17290245.404000] ohci_hcd 0000:00:03.0: wakeup
[17290245.788000] usb 1-1: new full speed USB device using ohci_hcd and address 3
[17290246.028000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17297683.012000] usb 1-1: USB disconnect, address 3
[17297683.012000] drivers/usb/class/usblp.c: usblp0: removed
[17386234.976000] ohci_hcd 0000:00:03.0: wakeup
[17386235.360000] usb 1-1: new full speed USB device using ohci_hcd and address 4
[17386235.600000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17390664.964000] usb 1-1: USB disconnect, address 4
[17390664.964000] drivers/usb/class/usblp.c: usblp0: removed
[17477340.536000] ohci_hcd 0000:00:03.0: wakeup
[17477340.920000] usb 1-1: new full speed USB device using ohci_hcd and address 5
[17477341.164000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17666606.728000] usb 1-1: USB disconnect, address 5
[17666606.728000] drivers/usb/class/usblp.c: usblp0: removed
[17666621.516000] ohci_hcd 0000:00:03.0: wakeup
[17666621.900000] usb 1-1: new full speed USB device using ohci_hcd and address 6
[17666622.140000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17669807.360000] eth0: Media Link Off
[17669832.360000] eth0: Media Link On 10mbps half-duplex
[17820161.416000] usb 1-1: USB disconnect, address 6
[17820161.416000] drivers/usb/class/usblp.c: usblp0: removed
[17820866.180000] ohci_hcd 0000:00:03.0: wakeup
[17820866.564000] usb 1-1: new full speed USB device using ohci_hcd and address 7
[17820866.804000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 7 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[17854616.688000] ibm_acpi: ec object not found
[17946368.560000] usb 1-1: USB disconnect, address 7
[17946368.560000] drivers/usb/class/usblp.c: usblp0: removed
[17983338.700000] usb 3-2: new high speed USB device using ehci_hcd and address 8
[17983339.260000] SCSI subsystem initialized
[17983339.340000] Initializing USB Mass Storage driver...
[17983339.344000] scsi0 : SCSI emulation for USB Mass Storage devices
[17983339.344000] usb-storage: device found at 8
[17983339.344000] usb-storage: waiting for device to settle before scanning
[17983339.344000] usbcore: registered new driver usb-storage
[17983339.344000] USB Mass Storage support registered.
[17983344.344000]   Vendor: Generic   Model: USB Flash Disk    Rev: 2.00
[17983344.344000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[17983344.360000] usb-storage: device scan complete
[17983344.408000] Driver 'sd' needs updating - please use bus_type methods
[17983345.492000] ready
[17983345.492000] SCSI device sda: 511488 512-byte hdwr sectors (262 MB)
[17983345.492000] sda: Write Protect is off
[17983345.492000] sda: Mode Sense: 03 00 00 00
[17983345.492000] sda: assuming drive cache: write through
[17983345.500000] SCSI device sda: 511488 512-byte hdwr sectors (262 MB)
[17983345.500000] sda: Write Protect is off
[17983345.500000] sda: Mode Sense: 03 00 00 00
[17983345.500000] sda: assuming drive cache: write through
[17983345.500000]  sda: unknown partition table
[17983345.508000] sd 0:0:0:0: Attached scsi removable disk sda
[17983345.540000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[17983355.196000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

Message curieux : sda : table de partition inconnue alors que je lis très bien ce qu'il y a sur la clé USB ;
la dernière ligne n'est pas non plus très favorable...

Merci bien cordialement.

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 13/12/2006, à 15:03

Clé USB non reconnue

#2 Le 13/12/2006, à 15:14

Re : Clé USB non reconnue

#3 Le 13/12/2006, à 15:22

Re : Clé USB non reconnue

#4 Le 13/12/2006, à 15:42

Re : Clé USB non reconnue

#5 Le 15/12/2006, à 11:55

Re : Clé USB non reconnue

#6 Le 15/12/2006, à 13:28

Re : Clé USB non reconnue

#7 Le 17/12/2006, à 09:06

Re : Clé USB non reconnue

#8 Le 17/12/2006, à 09:09

Re : Clé USB non reconnue

#9 Le 23/12/2006, à 07:20

Re : Clé USB non reconnue

#10 Le 23/12/2006, à 13:28

Re : Clé USB non reconnue

#11 Le 23/12/2006, à 20:55

Re : Clé USB non reconnue

#12 Le 24/12/2006, à 11:22

Re : Clé USB non reconnue

#13 Le 26/12/2006, à 02:03

Re : Clé USB non reconnue

Pied de page des forums