Pages : 1
#1 Le 08/06/2012, à 10:08
- bertrand47
Problème de gravure d'un CD Audio
Bonjour,
Depuis plusieurs jours, j'ai un problème de gravure de CD Audio. Tout d'abord mon CD Vierge n'apparait pas, mais est identifié lorsque je lance l'utilitaire de disque, ensuite, avec Brasero la gravure ne démarre pas et reste figée. Avec K3B, j'ai un message d'erreur: "la calibration de la puissance du laser a échoué. Le périphérique de gravure ne reconnait probablement pas le média."
Voici les informations de débogage:
Devices
-----------------------
PIONEER DVD-RW DVR-111D 1.23 (/dev/sr1, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R séquentiel, DVD-R double couche séquentiel, DVD+R double couche à saut, DVD RW à réinscription limitée, DVD-RW séquentiel, DVD+RW, DVD+R, DVD+R double couche, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Réinscription restreinte, Saut de couche] [%7]
HL-DT-ST DVD-ROM GDRH10N D70D (/dev/sr0, CD-ROM, DVD-ROM) [DVD-ROM, CD-ROM] [Aucune] [%7]
System
-----------------------
K3b Version: 2.0.2
KDE Version: 4.8.3 (4.8.3)
QT Version: 4.8.1
Kernel: 3.2.0-24-generic
Used versions
-----------------------
cdrecord: 1.1.11
cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/sr1'
devname: '/dev/sr1'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.11
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 0 = CD-DA
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'PIONEER '
Identification : 'DVD-RW DVR-111D'
Revision : '1.23'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1267712 = 1238 KB
FIFO size : 12582912 = 12288 KB
Speed set to 705 KB/s
pregap1: -1
Track 01: audio 24 MB (02:27.78) no preemp swab copy
Track 02: audio 40 MB (03:58.49) no preemp swab copy
Track 03: audio 42 MB (04:09.97) no preemp swab copy
Track 04: audio 34 MB (03:27.21) no preemp swab copy
Track 05: audio 20 MB (02:02.78) no preemp swab copy
Track 06: audio 66 MB (06:37.09) no preemp swab copy
Track 07: audio 36 MB (03:36.50) no preemp swab copy
Track 08: audio 28 MB (02:47.37) no preemp swab copy
Track 09: audio 44 MB (04:25.64) no preemp swab copy
Track 10: audio 35 MB (03:31.41) no preemp swab copy
Track 11: audio 14 MB (01:23.96) no preemp swab copy
Track 12: audio 49 MB (04:56.21) no preemp swab copy
Total size: 438 MB (43:24.45) = 195334 sectors
Lout start: 438 MB (43:26/34) = 195334 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -12369 (97:17/06)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 69
Manufacturer: Moser Baer India Limited
Manufacturer is guessed because of the orange forum embargo.
The orange forum likes to get money for recent information.
The information for this media may not be correct.
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 164515
Starting to write CD/DVD at speed 4.0 in real force SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Errno: 5 (Input/output error), send opc scsi sendcmd: no error
CDB: 54 01 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0E 00 00 00 00 15 02 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x15 Qual 0x02 (positioning error detected by read of medium) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 11.378s timeout 200s
/usr/bin/wodim: OPC failed.
Sending CUE sheet...
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 24 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 01 95 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 71 00 03 00 00 00 00 0E 00 00 00 00 0C 00 00 00
Sense Key: 0x3 Medium Error, deferred error, Segment 0
Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63504
cmd finished after 0.003s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 952560 bytes
Writing time: 41.261s
Average write speed 96.2x.
Fixating...
Fixating time: 0.012s
/usr/bin/wodim: fifo had 206 puts and 16 gets.
/usr/bin/wodim: fifo was 0 times empty and 2 times full, min fill was 93%.
cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr1 speed=4 -sao driveropts=burnfree -force -useinfo -audio /tmp/kde-bertrand/k3b_audio_0_01.inf /tmp/kde-bertrand/k3b_audio_0_02.inf /tmp/kde-bertrand/k3b_audio_0_03.inf /tmp/kde-bertrand/k3b_audio_0_04.inf /tmp/kde-bertrand/k3b_audio_0_05.inf /tmp/kde-bertrand/k3b_audio_0_06.inf /tmp/kde-bertrand/k3b_audio_0_07.inf /tmp/kde-bertrand/k3b_audio_0_08.inf /tmp/kde-bertrand/k3b_audio_0_09.inf /tmp/kde-bertrand/k3b_audio_0_10.inf /tmp/kde-bertrand/k3b_audio_0_11.inf /tmp/kde-bertrand/k3b_audio_0_12.inf
Je précise aussi que je grave sans problème des DVD-RW avec des fichiers ISO et que j'ai réussi une seule fois, jusqu'ici à graver un CD Audio entièrement, avec Brasero, hier.
Hors ligne
#2 Le 09/06/2012, à 00:19
- ThéoSon
Re : Problème de gravure d'un CD Audio
Bonjour ( voir Bonsoir ) bertrand47
sans détour , je te RECOMMANDE Xfburn , qui n'existe pas dans les liens de notre doc , mais que que tu peux trouver dans Synaptic , et
dans la logithèque
d'ailleurs , je ne comprends pas pourquoi le lien est crevé , Brasero est timide , K3B est moribond , ( oui , c'est méchant , mais il m'a
niqué 3 DVD+RW , l'enk...) bref , je porte pas plainte , mais je DIS , donc l'Ami , sans connaissance de ton O.S Buntu , JE TE conseil ( Vous , idem )
"La conscience est la dernière et la plus tardive évolution de la vie organique, et par conséquent ce qu'il y a de moins accompli et de plus fragile en elle. " Nietzshe
Hors ligne
#3 Le 09/06/2012, à 06:42
- bertrand47
Re : Problème de gravure d'un CD Audio
Merci l'ami pour ton conseil, c'est vrai XFBURN a un bon look, bien simple et sent bon l'efficacité, sans le tape-à l'oeil de K3B par exemple.
Mais... Il ne reconnait pas mon graveur. Alors, je pense qu'il y a un problème en amont chez moi. Mes CD-R vierges ne montent pas sur le bureau, alors que ceux gravés le font. Ensuite, j'ai remarqué que le fait de lancer l'Utilitaire de disque faisait apparaître mon CD dans Brasero ou K3B. Ensuite XFBURN me conseille de vérifier les droits en lecture et écriture sur mon graveur, ce que je ne sais pas faire... Pour l'instant.
Hors ligne
Pages : 1