Ubuntu-fr

thebrowser

Boot tres long, probleme lors de la détéction des peripheriques ide

Bonjour,

Lors du boot de ubuntu Edgy Eft, lorsque l'on voit la barre de chargement, la mienne reste bloquée à quelque chose comme 1% pendant au moins 2minutes, puis apres le boot continue tout seul.
C'est assez frustrant de devoir attendre à chaque fois.

Ce probleme apparait sous unbuntu, mais aussi knoppix, et slax. Par contre, sous XP, aucun probleme. J'ai pas testé d'autres distribution linux.

J'ai identifié les lines du dmesg qui revelent le probleme:

[17179574.752000] Probing IDE interface ide1...
[17179585.176000] hdc: no response (status = 0xa1), resetting drive
[17179590.384000] hdc: no response (status = 0xa1)
[17179600.856000] hdd: no response (status = 0xa1), resetting drive
[17179606.064000] hdd: no response (status = 0xa1)
...
[17179651.744000] hdc: no response (status = 0xa1), resetting drive
[17179656.952000] hdc: no response (status = 0xa1)
[17179667.424000] hdd: no response (status = 0xa1), resetting drive
[17179672.632000] hdd: no response (status = 0xa1)

Le fait que le kernel "sonde" les interfaces IDE est peut etre du au fait que le chipset de la carte mere n'est pas tout a fait supporté par le kernel.

[17179573.900000] ALI15X3: chipset revision 196
[17179573.900000] ALI15X3: not 100% native mode: will probe irqs later
[17179573.900000]     ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
[17179573.900000]     ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio

De plus, apres une petite recherche sur google, ce probleme semble se repeter chez d'autres personnes ayant le meme chipset "ALI15X3: chipset revision 196".

Voila, je ne sais pas quoi faire, alors toute aide me sera tres utile.
Si vous voulez d'autre informations sur ma configuration, demandez.

thebrowser

Voici l'intégralité de mon dmesg:

[17179569.184000] Linux version 2.6.17-11-generic (root@terranova) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Thu Feb 1 19:52:28 UTC 2007 (Ubuntu 2.6.17-11.35-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
[17179569.184000]  BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
[17179569.184000]  BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[17179569.184000] 127MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 262124
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   Normal zone: 225280 pages, LIFO batch:31
[17179569.184000]   HighMem zone: 32748 pages, LIFO batch:7
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 ASUS                                  ) @ 0x000f7930
[17179569.184000] ACPI: RSDT (v001 ASUS   A7A266-E 0x42302e31 MSFT 0x31313031) @ 0x3ffec000
[17179569.184000] ACPI: FADT (v001 ASUS   A7A266-E 0x42302e31 MSFT 0x31313031) @ 0x3ffec080
[17179569.184000] ACPI: BOOT (v001 ASUS   A7A266-E 0x42302e31 MSFT 0x31313031) @ 0x3ffec040
[17179569.184000] ACPI: DSDT (v001   ASUS A7A266-E 0x00001000 MSFT 0x0100000b) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0xe408
[17179569.184000] Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda3 ro quiet splash
[17179569.184000] Local APIC disabled by BIOS (or by default) -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (0180c000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Detected 1544.800 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.540000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179570.544000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.584000] Memory: 1029628k/1048496k available (1911k kernel code, 18108k reserved, 1073k data, 308k init, 130992k highmem)
[17179570.584000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179570.664000] Calibrating delay using timer specific routine.. 3091.78 BogoMIPS (lpj=6183560)
[17179570.664000] Security Framework v1.0.0 initialized
[17179570.664000] SELinux:  Disabled at boot.
[17179570.664000] Mount-cache hash table entries: 512
[17179570.664000] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[17179570.664000] CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[17179570.664000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179570.664000] CPU: L2 Cache: 256K (64 bytes/line)
[17179570.664000] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[17179570.664000] Checking 'hlt' instruction... OK.
[17179570.680000] SMP alternatives: switching to UP code
[17179570.680000] Freeing SMP alternatives: 16k freed
[17179570.680000] checking if image is initramfs... it is
[17179571.272000] Freeing initrd memory: 5326k freed
[17179571.272000] ACPI: Core revision 20060707
[17179571.272000] ACPI: Looking for DSDT ... not found!
[17179571.272000] ACPI: setting ELCR to 0200 (from 0a00)
[17179571.272000] CPU0: AMD Athlon(TM) XP1800+ stepping 02
[17179571.272000] SMP motherboard not detected.
[17179571.272000] Local APIC not detected. Using dummy APIC emulation.
[17179571.272000] Brought up 1 CPUs
[17179571.272000] migration_cost=0
[17179571.272000] NET: Registered protocol family 16
[17179571.272000] EISA bus registered
[17179571.272000] ACPI: bus type pci registered
[17179571.276000] PCI: PCI BIOS revision 2.10 entry at 0xf1170, last bus=1
[17179571.276000] PCI: Using configuration type 1
[17179571.276000] Setting up standard PCI resources
[17179571.284000] ACPI: Interpreter enabled
[17179571.284000] ACPI: Using PIC for interrupt routing
[17179571.284000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[17179571.284000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.284000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.284000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.284000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[17179571.288000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.288000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.288000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[17179571.288000] ACPI: PCI Interrupt Link [LNKI] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[17179571.288000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179571.288000] PCI: Probing PCI hardware (bus 00)
[17179571.288000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[17179571.292000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:04.0
[17179571.292000] PCI quirk: region e400-e43f claimed by ali7101 ACPI
[17179571.292000] PCI quirk: region e800-e81f claimed by ali7101 SMB
[17179571.292000] Boot video device is 0000:01:00.0
[17179571.292000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179571.292000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[17179571.296000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179571.296000] pnp: PnP ACPI init
[17179571.300000] pnp: PnP ACPI: found 15 devices
[17179571.300000] PnPBIOS: Disabled by ACPI PNP
[17179571.300000] PCI: Using ACPI for IRQ routing
[17179571.300000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179571.308000] pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
[17179571.308000] pnp: 00:02: ioport range 0xe800-0xe81f has been reserved
[17179571.308000] pnp: 00:02: ioport range 0x40b-0x40b has been reserved
[17179571.308000] pnp: 00:02: ioport range 0x480-0x48f has been reserved
[17179571.308000] pnp: 00:02: ioport range 0x4d6-0x4d6 has been reserved
[17179571.308000] PCI: Bridge: 0000:00:01.0
[17179571.308000]   IO window: d000-dfff
[17179571.308000]   MEM window: be800000-bfefffff
[17179571.308000]   PREFETCH window: c0000000-efffffff
[17179571.308000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179571.308000] NET: Registered protocol family 2
[17179571.348000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179571.348000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[17179571.348000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[17179571.352000] TCP: Hash tables configured (established 131072 bind 65536)
[17179571.352000] TCP reno registered
[17179571.352000] Simple Boot Flag at 0x3a set to 0x1
[17179571.352000] audit: initializing netlink socket (disabled)
[17179571.352000] audit(1171188412.352:1): initialized
[17179571.352000] highmem bounce pool size: 64 pages
[17179571.352000] VFS: Disk quotas dquot_6.5.1
[17179571.352000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179571.352000] Initializing Cryptographic API
[17179571.352000] io scheduler noop registered
[17179571.352000] io scheduler anticipatory registered
[17179571.352000] io scheduler deadline registered
[17179571.352000] io scheduler cfq registered (default)
[17179571.352000] Limiting direct PCI/PCI transfers.
[17179571.352000] Activating ISA DMA hang workarounds.
[17179571.352000] isapnp: Scanning for PnP cards...
[17179571.708000] isapnp: No Plug & Play device found
[17179571.732000] Real Time Clock Driver v1.12ac
[17179571.732000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179571.732000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.736000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.736000] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.736000] 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.736000] mice: PS/2 mouse device common for all mice
[17179571.736000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179571.736000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179571.736000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179571.736000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[17179571.740000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179571.740000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179571.740000] EISA: Probing bus 0 at eisa.0
[17179571.740000] EISA: Detected 0 cards.
[17179571.740000] TCP bic registered
[17179571.740000] NET: Registered protocol family 1
[17179571.740000] NET: Registered protocol family 8
[17179571.740000] NET: Registered protocol family 20
[17179571.740000] Using IPI No-Shortcut mode
[17179571.740000] ACPI: (supports S0 S1 S4 S5)
[17179571.740000] Freeing unused kernel memory: 308k freed
[17179571.764000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179573.080000] Capability LSM initialized
[17179573.124000] ACPI: Invalid PBLK length [5]
[17179573.900000] ALI15X3: IDE controller at PCI slot 0000:00:04.0
[17179573.900000] ACPI: Unable to derive IRQ for device 0000:00:04.0
[17179573.900000] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[17179573.900000] ALI15X3: chipset revision 196
[17179573.900000] ALI15X3: not 100% native mode: will probe irqs later
[17179573.900000]     ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
[17179573.900000]     ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
[17179573.900000] Probing IDE interface ide0...
[17179574.232000] hda: Maxtor 6Y080P0, ATA DISK drive
[17179574.680000] hdb: HL-DT-ST GCE-8160B, ATAPI CD/DVD-ROM drive
[17179574.736000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179574.752000] Probing IDE interface ide1...
[17179585.176000] hdc: no response (status = 0xa1), resetting drive
[17179590.384000] hdc: no response (status = 0xa1)
[17179600.856000] hdd: no response (status = 0xa1), resetting drive
[17179606.064000] hdd: no response (status = 0xa1)
[17179606.128000] hda: max request size: 128KiB
[17179606.140000] hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=16383/255/63, UDMA(100)
[17179606.140000] hda: cache flushes supported
[17179606.140000]  hda: hda1 hda2 hda3 hda4 < hda5 >
[17179606.172000] hdb: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
[17179606.172000] Uniform CD-ROM driver Revision: 3.20
[17179606.488000] Probing IDE interface ide1...
[17179641.272000] ide1: Wait for ready failed before probe !
[17179641.320000] usbcore: registered new driver usbfs
[17179641.320000] usbcore: registered new driver hub
[17179641.324000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179641.324000] ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 9
[17179641.324000] PCI: setting IRQ 9 as level-triggered
[17179641.324000] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKI] -> GSI 9 (level, low) -> IRQ 9
[17179641.324000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[17179641.324000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[17179641.324000] ohci_hcd 0000:00:02.0: irq 9, io mem 0xbe000000
[17179641.380000] usb usb1: configuration #1 chosen from 1 choice
[17179641.380000] hub 1-0:1.0: USB hub found
[17179641.380000] hub 1-0:1.0: 4 ports detected
[17179641.484000] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
[17179641.484000] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKE] -> GSI 9 (level, low) -> IRQ 9
[17179641.484000] ohci_hcd 0000:00:06.0: OHCI Host Controller
[17179641.484000] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2
[17179641.484000] ohci_hcd 0000:00:06.0: irq 9, io mem 0xbd000000
[17179641.540000] usb usb2: configuration #1 chosen from 1 choice
[17179641.540000] hub 2-0:1.0: USB hub found
[17179641.540000] hub 2-0:1.0: 2 ports detected
[17179641.788000] usb 1-2: new full speed USB device using ohci_hcd and address 2
[17179641.996000] usb 1-2: configuration #1 chosen from 1 choice
[17179651.744000] hdc: no response (status = 0xa1), resetting drive
[17179656.952000] hdc: no response (status = 0xa1)
[17179667.424000] hdd: no response (status = 0xa1), resetting drive
[17179672.632000] hdd: no response (status = 0xa1)
[17179672.700000] Attempting manual resume
[17179672.724000] kjournald starting.  Commit interval 5 seconds
[17179672.724000] EXT3-fs: mounted filesystem with ordered data mode.
[17179684.072000] PCI: Enabling device 0000:00:0a.0 (0014 -> 0017)
[17179684.072000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[17179684.072000] PCI: setting IRQ 11 as level-triggered
[17179684.072000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[17179684.072000] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[17179684.072000] 0000:00:0a.0: 3Com PCI 3c905C Tornado at f8836000.
[17179684.112000] input: PC Speaker as /class/input/input1
[17179684.124000] Linux agpgart interface v0.101 (c) Dave Jones
[17179684.128000] agpgart: Detected ALi M1647 chipset
[17179684.136000] agpgart: AGP aperture is 128M @ 0xf0000000
[17179684.160000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179684.172000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179684.200000] ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[17179684.200000] ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted.
[17179684.272000] Floppy drive(s): fd0 is 1.44M
[17179684.280000] acx: Loaded combined PCI/USB driver, firmware_ver=default
[17179684.280000] acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
[17179684.280000] PCI: Enabling device 0000:00:09.0 (0004 -> 0006)
[17179684.284000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[17179684.284000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[17179684.284000] acx: found ACX111-based wireless network card at 0000:00:09.0, irq:11, phymem1:0xBC000000, phymem2:0xBB800000, mem1:0xf88fc000, mem1_size:8192, mem2:0xf89c0000, mem2_size:131072
[17179684.304000] FDC 0 is a post-1991 82077
[17179684.808000] parport: PnPBIOS parport detected.
[17179684.808000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179684.860000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[17179684.864000] eth0:  setting half-duplex.
[17179684.892000] Linux video capture interface: v1.00
[17179684.964000] input: PS2++ Logitech Wheel Mouse as /class/input/input2
[17179685.052000] quickcam: QuickCam USB camera found (driver version QuickCam USB 0.6.3 $Date: 2005/04/15 19:32:49 $)
[17179685.052000] quickcam: Kernel:2.6.17-11-generic bus:1 class:FF subclass:FF vendor:046D product:0870
[17179685.156000] quickcam: Sensor HDCS-1020 detected
[17179685.164000] quickcam: Registered device: /dev/video0
[17179685.164000] usbcore: registered new driver quickcam
[17179685.324000] ts: Compaq touchscreen protocol output
[17179685.460000] acx: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x16 (Radia), EEPROM version 0x05, uploaded firmware 'Rev 1.2.1.34' (0x03010101)
[17179685.460000] acx v0.3.21: net device wlan0, driver compiled against wireless extensions 20 and Linux 2.6.17-11-generic
[17179685.460000] usbcore: registered new driver acx_usb
[17179685.460000] PCI: Enabling device 0000:00:05.0 (0084 -> 0085)
[17179685.460000] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
[17179685.460000] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11
[17179685.692000] wlan0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
[17179685.900000] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[17179685.904000] [fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[17179685.904000] [fglrx] module loaded - fglrx 8.33.6 [Jan  8 2007] on minor 0
[17179685.952000] lp0: using parport0 (interrupt-driven).
[17179686.048000] Adding 586332k swap on /dev/disk/by-uuid/3af482da-20bb-4775-8ef2-21bdb74babe5.  Priority:-1 extents:1 across:586332k
[17179686.076000] NET: Registered protocol family 17
[17179686.116000] EXT3 FS on hda3, internal journal
[17179686.388000] NTFS driver 2.1.27 [Flags: R/O MODULE].
[17179686.464000] NTFS volume version 3.1.
[17179691.800000] ACPI: Power Button (FF) [PWRF]
[17179691.800000] ACPI: Power Button (CM) [PWRB]
[17179691.952000] ibm_acpi: ec object not found
[17179691.992000] pcc_acpi: loading...
[17179696.152000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[17179696.152000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179698.388000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179698.388000] apm: overridden by ACPI.
[17179698.976000] [fglrx] Internal AGP support requested, but kernel AGP support active.
[17179698.976000] [fglrx] Have to use kernel AGP support to avoid conflicts.
[17179698.976000] [fglrx] AGP detected, AgpState   = 0x1b000217 (hardware caps of chipset)
[17179698.980000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[17179698.980000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[17179698.980000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[17179698.980000] [fglrx] AGP enabled,  AgpCommand = 0x1b000314 (selected caps)
[17179698.992000] [fglrx] total      GART = 134217728
[17179698.992000] [fglrx] free       GART = 118222848
[17179698.992000] [fglrx] max single GART = 118222848
[17179698.992000] [fglrx] total      LFB  = 134217728
[17179698.992000] [fglrx] free       LFB  = 116002816
[17179698.992000] [fglrx] max single LFB  = 116002816
[17179698.992000] [fglrx] total      Inv  = 0
[17179698.992000] [fglrx] free       Inv  = 0
[17179698.992000] [fglrx] max single Inv  = 0
[17179698.992000] [fglrx] total      TIM  = 0
[17179704.036000] Bluetooth: Core ver 2.8
[17179704.036000] NET: Registered protocol family 31
[17179704.036000] Bluetooth: HCI device and connection manager initialized
[17179704.036000] Bluetooth: HCI socket layer initialized
[17179704.072000] Bluetooth: L2CAP ver 2.8
[17179704.072000] Bluetooth: L2CAP socket layer initialized
[17179704.076000] Bluetooth: RFCOMM socket layer initialized
[17179704.076000] Bluetooth: RFCOMM TTY layer initialized
[17179704.076000] Bluetooth: RFCOMM ver 1.7
[17179714.536000] NET: Registered protocol family 10
[17179714.536000] lo: Disabled Privacy Extensions
[17179714.536000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[17179714.536000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[17179714.536000] IPv6 over IPv4 tunneling driver

thebrowser

Re : Boot tres long, probleme lors de la détéction des peripheriques ide

up..

thebrowser

Re : Boot tres long, probleme lors de la détéction des peripheriques ide

up..

thebrowser

Re : Boot tres long, probleme lors de la détéction des peripheriques ide

up..

racoon97

Re : Boot tres long, probleme lors de la détéction des peripheriques ide

Il est inutile de faire un up toutes les dix minutes, les messages sans réponses sont accessibles en un clic. Y répondre toi-même diminue les chances pour que l'on puisse accéder à ton message initial. Si tu n'a pas encore de réponses c'est que personne pour le moment ne peut t'aider pour ton problème. Patientes un peu

---

Pas de logiciel de montage vidéo professionnel sous Linux ? Demandez à Sony son portage de Vegas Pro sous Linux... ou attendez Lightworks ;)