Pages : 1
#1 Le 18/11/2012, à 14:20
- droopy
Wifi WM3545abg sur Dell 9400....
Bonjour à Tous,
Encore un problème avec la Wifi sur un Dell 9400 équipé d'une carte Intel WM3945abg sous un OS Ubuntu 10.04.2 LTS.
J'ai suivi les instruction du post:
http://doc.ubuntu-fr.org/wifi_intel_3945abg
J'ai donc créé le fichier "/etc/modprobe.d/iwl3945.conf".
La combinaison de touches "Fn+F2" permet bien "d'activer" le voyant de la Wifi mais la carte ne semble pas pour autant être active....
D'autre part j'ai installé "wifi radar" pour surveiller le fonctionnement sans résultat pour l'instant.
La commande: "iwconfig" me retourne le résultat suivant:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
La commande "lspci | grep -i net" me donne:
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Enfin concernant le noyau, la commande "cat /proc/version":
Linux version 2.6.32-45-generic (buildd@aatxe) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5.1) ) #99-Ubuntu SMP Tue Oct 16 16:31:11 UTC 2012
Merci par avance pour vos informations (la gestion de la wifi reste une galère...)
Longue Vie au Libre ....
@ + droopy
Hors ligne
#2 Le 18/11/2012, à 15:39
- toutafai
Re : Wifi WM3545abg sur Dell 9400....
Salut,
Post les informations demandé dans le post "A lire avant de poster !!!", post épinglé (=au début/en haut) de la liste des sujets de la section wifi de ce forum.
Ps : oublie wifi radar, désinstalle-le car il ne sert à rien.
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#3 Le 18/11/2012, à 20:45
- droopy
Re : Wifi WM3545abg sur Dell 9400....
Salut "Toutafai",
Sur tes conseils j'ai dé-installé "wifi-radar" via la commande "sudo apt-get autoremove wifi-radar".
Pour la suite résultat des différentes commandes, voir ci-dessous:
cat /etc/lsb-release
[DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=10.04
DISTRIB_CODENAME=lucid
DISTRIB_DESCRIPTION="Ubuntu 10.04.4 LTS"]
lsusb
[Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 005: ID 0a5c:4503 Broadcom Corp.
Bus 001 Device 004: ID 0a5c:4502 Broadcom Corp.
Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 001 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
]
lspci
[00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce Go 7900 GS] (rev a1)
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
03:01.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 0a)
03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 05)
03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff)
0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
]
lspci -nn | grep -i net
[03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
]
lspci -k
[00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port (rev 03)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 01)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01)
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01)
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01)
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01)
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01)
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01)
Kernel modules: iTCO_wdt, intel-rng
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 01)
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
Kernel modules: i2c-i801
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce Go 7900 GS] (rev a1)
Kernel driver in use: nouveau
Kernel modules: nvidiafb, nouveau
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Kernel driver in use: b44
Kernel modules: b44
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
03:01.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 0a)
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 05)
03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff)
0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Kernel driver in use: iwl3945
Kernel modules: iwl3945
]
sudo lshw -C network
[sudo] password …........:
[ *-network
description: Wireless interface
product: PRO/Wireless 3945ABG [Golan] Network Connection
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:0c:00.0
logical name: wlan0
version: 02
serial: 00:19:d2:4e:66:dd
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwl3945 latency=0 multicast=yes wireless=IEEE 802.11abg
resources: irq:28 memory:ecfff000-ecffffff
*-network
description: Ethernet interface
product: BCM4401-B0 100Base-TX
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
logical name: eth0
version: 02
serial: 00:15:c5:5a:ad:9e
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=192.168.0.17 latency=64 link=yes multicast=yes port=twisted pair speed=100MB/s
resources: irq:17 memory:ecbfe000-ecbfffff
]
lsmod
[Module Size Used by
binfmt_misc 6587 1
fbcon 35102 71
tileblit 1999 1 fbcon
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
vga16fb 11385 0
vgastate 8961 1 vga16fb
ppdev 5259 0
snd_hda_codec_idt 52074 1
snd_hda_intel 22069 2
snd_hda_codec 74297 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 5412 1 snd_hda_codec
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
snd_pcm 70694 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1338 0
snd_seq_oss 26722 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
snd_seq_midi_event 6003 2 snd_seq_oss,snd_seq_midi
nouveau 467048 2
snd_seq 47263 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ttm 49847 1 nouveau
arc4 1153 2
snd_timer 19130 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
drm_kms_helper 29329 1 nouveau
snd 54244 16 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
iwl3945 68727 0
sdhci_pci 5470 0
drm 163779 4 nouveau,ttm,drm_kms_helper
i2c_algo_bit 5028 1 nouveau
soundcore 6620 1 snd
snd_page_alloc 7076 2 snd_hda_intel,snd_pcm
iwlcore 106149 1 iwl3945
ricoh_mmc 2923 0
sdhci 15494 1 sdhci_pci
joydev 8740 0
intel_agp 24375 0
dell_wmi 1793 0
mac80211 205434 2 iwl3945,iwlcore
agpgart 31724 3 ttm,drm,intel_agp
usbhid 36110 0
video 17375 0
output 1871 1 video
led_class 2864 3 iwl3945,iwlcore,sdhci
hid 67288 1 usbhid
psmouse 63677 0
dell_laptop 6888 0
dcdbas 5422 1 dell_laptop
cfg80211 126528 3 iwl3945,iwlcore,mac80211
serio_raw 3978 0
lp 7028 0
parport 32635 2 ppdev,lp
ohci1394 26950 0
b44 25574 0
ieee1394 81181 1 ohci1394
ssb 38934 1 b44
mii 4381 1 b44
]
iwconfig
[lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
]
ifconfig
[eth0 Link encap:Ethernet HWaddr 00:15:c5:5a:ad:9e
inet adr:192.168.0.17 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::215:c5ff:fe5a:ad9e/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:3580 erreurs:0 :0 overruns:0 frame:0
TX packets:3624 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:3036189 (3.0 MB) Octets transmis:419070 (419.0 KB)
Interruption:17
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:12 erreurs:0 :0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:720 (720.0 B) Octets transmis:720 (720.0 B)
wlan0 Link encap:Ethernet HWaddr 00:19:d2:4e:66:dd
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
]
sudo iwlist scan
[lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 No scan results
]
uname -r -m
[2.6.32-45-generic i686
]
at /etc/network/interfaces
[auto lo
iface lo inet loopback
]
nm-tool
[NetworkManager Tool
State: connected
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: iwl3945
State: disconnected
Default: no
HW Address: 00:19:D2:4E:66:DD
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
- Device: eth0 [Auto eth0] ----------------------------------------------------
Type: Wired
Driver: b44
State: connected
Default: yes
HW Address: 00:15:C5:5A:AD:9E
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.1.......
Prefix: 24 (255.255.255.0)
Gateway: 192.168......
DNS: 212.2.........
DNS: 212.27........]
sudo rfkill list
[0: dell-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: dell-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
2: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
]
Merci par avance pour tes suggestions....
Longue Vie au Libre ....
@ + droopy
Hors ligne
#4 Le 19/11/2012, à 18:13
- toutafai
Re : Wifi WM3545abg sur Dell 9400....
Bonsoir,
Rien d'anormal dans les retours, mis à part que ta carte wifi "ne voit" aucun point d'acces.... le wifi sur ta box est-il bien activé ? si non, allume-le. Si oui, ben la je vois pas : cache-tu le nom ssid de ta borne wifi ?
sinon autre piste, tenter avec ndiswrapper.
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#5 Le 19/11/2012, à 20:37
- droopy
Re : Wifi WM3545abg sur Dell 9400....
Bonsoir "Toutafai",
Mon avis est que l'utilisation de "Ndiswrapper" (comme précisé sur le post correspondant du site) reste du "bidouillage"....
En cherchant sur le net, j'ai trouvé un lien sur un site Intel (qui propose un microcode pour linux "iwlwifi-3945-ucode-15.32.2.9.tzg") :
http://www.intellinuxwireless.org/?n=Downloads
Quel est ton avis ?
Faut-il prévoir une compilation dans ce cas ?
Si l'utilisation de "Ndiswrapper" est cependant nécessaire, il semble que c'est le driver pour XP qu'il faut charger....
Merci par avance pour tes compléments.
Longue Vie au Libre ....
@ + droopy
Hors ligne
#6 Le 19/11/2012, à 23:32
- toutafai
Re : Wifi WM3545abg sur Dell 9400....
Pour le firmware, il faut juste le copier dans /lib/firmware. (fait une sauvegarde de l'ancien au cas ou).
Ndiswrapper : oui du bidouillage dans le sens ou on utilise un pilote proprietaire dans un os libre...mais cela fait fonctionner le matériel, c'est pas le principal ?
De plus c'est facile a mettre en place et a supprimer, que demande le peuple ^^ ?
On préfère en général les anciennes versions de pilote (comme pour XP) car plus éprouvé et moins de bug que des versions plus recente...
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#7 Le 20/11/2012, à 20:17
- droopy
Re : Wifi WM3545abg sur Dell 9400....
Bonsoir,
J'ai testé la solution de copie du fichier "iwlwifi-3945-2.ucode" dans le répertoire "/lib/firmware", via la commande "sudo cp iwlwifi-3945-2.ucode /lib/firmware" sans que cette action modifie le fonctionnement du chipset Wifi....
Il est vrai que cette solution me semblait quelque peu simpliste.....
Ndiswrapper:
Je rencontre quelques problèmes avec les extractions des fichiers .inf à partie des .exe, sur les 3 pilotes téléchargés ("Wireless_15.3.1_x32.exe", "Wireless_15.3.1_Dx32.exe" et "intel_multi-device_A13_R171131.exe"), je n'ai pas pu extraire le moindre .inf via les commandes "cabextract xxx.exe" ou "unshield xxx.exe".
Les retours des commandes sont les suivants:
[Wireless_15.3.1_x32.exe: no valid cabinets found
All done, errors in processing 1 file(s)] pour "cabextract ..."
et
[Unknown action 'W' on command line.
Syntax:
unshield [-c COMPONENT] [-d DIRECTORY] [-D LEVEL] [-g GROUP] [-GhlOrV] c|g|l|t|x CABFILE
Options:
-c COMPONENT Only list/extract this component
-d DIRECTORY Extract files to DIRECTORY
-D LEVEL Set debug log level
0 - No logging (default)
1 - Errors only
2 - Errors and warnings
3 - Errors, warnings and debug messages
-g GROUP Only list/extract this file group
-h Show this help message
-j Junk paths (do not make directories)
-L Make file and directory names lowercase
-O Use old compression
-r Save raw data (do not decompress)
-V Print copyright and version information
Commands:
c List components
g List file groups
l List files
t Test files
x Extract files
Other:
CABFILE The file to list or extract contents of] pour "unshield xxx". Dans ce cas une option à la commande semble être attendue.....
Merci pour tes éventuels compléments.
Dernière modification par droopy (Le 21/11/2012, à 19:07)
Longue Vie au Libre ....
@ + droopy
Hors ligne
#8 Le 21/11/2012, à 21:34
- toutafai
Re : Wifi WM3545abg sur Dell 9400....
essaye de trouver une autre version (pas en .exe)
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#9 Le 22/11/2012, à 19:19
- droopy
Re : Wifi WM3545abg sur Dell 9400....
Bonsoir Toutafai,
J'ai tenté la solution "wine" décrite dans le post "Ndiswrapper" pour l'extraction avec l'un des .exe.
Le problème est que je me retrouve à présent avec plusieurs fichiers .inf qui sont les suivants (que j'ai placé dans "install_wifi" toujours suivant le post):
netwlx32.inf
netwnx32.inf
netwxn00.inf
Quel est le pilote .inf (voir quels sont les pilotes .inf) que je dois lancer avec la commande "sudo ndiswrapper -i votre_pilote.inf" (toujour suivant le post Ndiswrapper).
Pour info dans l'état actuel de ma config la commande: "dmesg | grep iwl"
[ 17.381361] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 17.381364] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 17.381476] iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 17.381491] iwl3945 0000:0c:00.0: setting latency timer to 64
[ 17.482575] iwl3945 0000:0c:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 17.482579] iwl3945 0000:0c:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 17.482915] iwl3945 0000:0c:00.0: irq 28 for MSI/MSI-X
[ 17.488909] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 18.048983] iwl3945 0000:0c:00.0: firmware: requesting iwlwifi-3945-2.ucode
[ 18.294060] iwl3945 0000:0c:00.0: loaded firmware version 15.32.2.9
[ 18.364948] Registered led device: iwl-phy0::radio
[ 18.365462] Registered led device: iwl-phy0::assoc
[ 18.365486] Registered led device: iwl-phy0::RX
[ 18.365504] Registered led device: iwl-phy0::TX
[ 22.116041] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 42.473063] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 72.472044] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 112.473407] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 162.472109] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 222.472077] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 282.480103] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 342.472134] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 402.472087] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 462.472133] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 522.472107] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 582.472118] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 642.472112] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 702.472076] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 762.472111] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 822.472117] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
[ 882.472116] iwl3945 0000:0c:00.0: Failed to get channel info for channel 140 [0]
J'ai toujours le driver "iwlwifi-3945-2.ucode" copier dans "/lib/firmware" (y a pas un éventuel problème de permission ?).
Une dernière info la carte fonctionne, car testée sous XP sur le même PC est en DualBoot....
Je ne te cache pas, que je commence a être usé par les tentatives successives.....
Dernière modification par droopy (Le 22/11/2012, à 19:27)
Longue Vie au Libre ....
@ + droopy
Hors ligne
#10 Le 22/11/2012, à 21:19
- toutafai
Re : Wifi WM3545abg sur Dell 9400....
pour le pilote windows : j'en sais rien du tout...sinon, je repense a un truc.
sudo gedit /etc/modprobe.d/iwl3945.conf
une page blanche s'ouvre, dedans tu mets la ligne suivante :
options iwl3945 disable_hw_scan=1
tu enregistre et tu ferme, puis :
sudo modprobe -r iwl3945 && sleep 3 && sudo modprobe iwl3945 && sleep 3 && sudo ifconfig wlan0 up #patiente 6 secondes :-) et
... re test ton wifi.
PS : La 10.04 commence a dater, tu n'aurais certainement pas ce problème avec une version plus récente
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#11 Le 23/11/2012, à 20:21
- droopy
Re : Wifi WM3545abg sur Dell 9400....
Bonsoir Toutafai,
J'ai lancé les commandes proposées toujours sans résultat.....
A savoir que le fichier "/etc/modprobe.d/iwl3945.conf" de ma config n'était pas vide puisque celui-ci contenait le texte contenu dans le poste:
http://doc.ubuntu-fr.org/wifi_intel_3945abg
[alias wlan0 iwl3945
options iwl3945 disable_hw_scan=1]
J'ai même fini par upgrader à la version 12.04.1 LTS, .....et surprise, la carte ne fonctionne toujours pas.
Cette dernière version customisé (effet graphiques sympas, à la "mac"), mais concernant la prise en charge matériel rien de mieux.
C'est presque pire, car je n'arrive même plus à activer la carte via la combinaison des touches Fn+F2 !!
PS: J'ai lancé également tes dernières commandes après le upgrade vers la 12.04.1 LTS, et j'ai l'impression d'avoir un message d'erreur durant la phase d'arrêt du PC..... (mais j'ai n'arrive pas à voir le détail)
Dernière modification par droopy (Le 29/11/2012, à 10:10)
Longue Vie au Libre ....
@ + droopy
Hors ligne
Pages : 1