Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 01/12/2012, à 13:36

jcpain

[Résolu] Comment installer un pilote pour Wifi téléchargé ?

Bonjour,
Je débute (depuis 4 heures). Je suis sur xubuntu 10.04
J'utilise un adaptateur USB pour le wifi:  Belkin Surf Micro WLAN USB Adapter
Je capte mon réseau mais je ne peux pas me connecter.
D'après mes recherches sur le forum (http://forum.ubuntu-fr.org/viewtopic.php?id=445810), il faut télécharger puis installer un pilote (pour linux).
J'ai donc le pilote (dossier zip) mais après je suis perdu (et je sature car cela fait 4 heures que j'y suis...).
Comment installer le pilote ?

Ensuite d'arpès le forum: "il faut mettre le nom du module dans /etc/modules"
Quelqu'un peut-il traduire cette consigne ?

Merci d'avance pour votre aide.

Dernière modification par jcpain (Le 05/12/2012, à 14:33)

Hors ligne

#2 Le 01/12/2012, à 15:19

brital

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Peux tu nous donner le contenu du zip?

Hors ligne

#3 Le 01/12/2012, à 15:26

renyeu

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Bonjour,
Si tu as téléchargé l'archive, décompresses la.
Elle doit contenir un fichier README (lisez-moi wink ) dans lequel tu devrais trouver la procédure d'installation.
Cdlt
Renyeu

Hors ligne

#4 Le 01/12/2012, à 20:05

jcpain

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Bonjour,
Merci pour vos réponses.
J'avais déjà "étudié" le README mais sans rien comprendre...
Voici le contenu. Merci d'avance pour vos explications.
===============================================================================
        Software Package - Component
===============================================================================
    1. ReleaseNotes.doc

    2. document/

    3. driver source code

        3.1 Makefile - to build the modules

        3.2 Script and configuration for DHCP:
            "wlan0dhcp"
            "ifcfg-wlan0"

        3.3 Example of supplicant configuration file:
            "wpa1.conf"

        3.4 Script to run wpa_supplicant
            "runwpa"

        3.5 Script to clean relative modules
            "clean"

    4. wpa_supplicant/wpa_supplicant-0.6.9_wps_patch_20100201.zip
            The tool help the wlan network to communicate under the
            protection of WPAPSK mechanism (WPA/WPA2) and add WPS patch

    5. install.sh
       Script to easy make 8192cu driver.
   
==================================================================================================================
        User Guide(1) - connecting wireless networking using "Network Manager" GUI utility (For PC Linux)
==================================================================================================================
            (1) Network Manager is a utility attempts to make use of wireless networking easy.

            (2) Notes: if you want to use the following command-line method to connect wireless networking,
                        please disable the "Network Manager", because "Network Manager" will conflict with method of command line .

==================================================================================================================
        User Guide(2) - Using the wpa_cli & wpa_supplicant tools (For embedded Linux)
==================================================================================================================

    Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

==================================================================================================================
        User Guide(3) - Set wireless lan MIBs in Command Line (Legacy command - Not recommend)
==================================================================================================================
This driver uses Wireless Extension as an interface allowing you to set
Wireless LAN specific parameters.

Current driver supports "iwlist" to show the device status of nic
        iwlist wlan0 [parameters]
where
        parameter explaination          [parameters]
        -----------------------         -------------
        Show available chan and freq    freq / channel
        Show and Scan BSS and IBSS     scan[ning]
        Show supported bit-rate         rate / bit[rate]

For example:
    iwlist wlan0 channel
    iwlist wlan0 scan
    iwlist wlan0 rate

Driver also supports "iwconfig", manipulate driver private ioctls, to set
MIBs.

    iwconfig wlan0 [parameters] [val]
where
    parameter explaination      [parameters]        [val] constraints
        -----------------------     -------------        ------------------
        Connect to AP by address    ap                  [mac_addr]
        Set the essid, join (I)BSS  essid                 [essid]
        Set operation mode          mode                {Managed|Ad-hoc}
        Set keys and security mode  key/enc[ryption]    {N|open|restricted|off}

For example:
    iwconfig wlan0 essid "ap_name"
    iwconfig wlan0 ap XX:XX:XX:XX:XX:XX
    iwconfig wlan0 mode Ad-hoc
    iwconfig wlan0 essid "name" mode Ad-hoc
    iwconfig wlan0 key 0123456789 [2] open
    iwconfig wlan0 key off
    iwconfig wlan0 key restricted [3] 0123456789
        Note: Better to set these MIBS without GUI such as NetworkManager and be sure that our
              nic has been brought up before these settings. WEP key index 2-4 is not supportted by
              NetworkManager.

===============================================================================
        Getting IP address (For User Guide(2) & User Guide(3))
===============================================================================
After start up the nic and connect to AP successfully, the network needs to obtain an IP address
before transmit/receive data.
This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"
command, or using DHCP.

If using DHCP, setting steps is as below:
    (1)check if the WiFi had connected to an AP via "iwconfig" command
        $> iwconfig

    (2)run the script which run the dhclient
        $> ./wlan0dhcp
           or
        dhcpcd wlan0
                  (Some network admins require that you use the
                  hostname and domainname provided by the DHCP server.
                  In that case, use
        dhcpcd -HD wlan0)


===============================================================================
        WPAPSK/WPA2PSK - using wpa_supplicant (For User Guide(3))
===============================================================================

    Wpa_supplicant helps to secure wireless connection with the protection of
WPAPSK/WPA2PSK mechanism. Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
        WPS - PIN & PBC methods
===============================================================================

        (*) Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
        Power Saving Mode
===============================================================================

        (*) Please refer to the document/HowTo enable the power saving functionality.doc

Hors ligne

#5 Le 02/12/2012, à 15:50

chibbata

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

salut

télécharges le driver RTL8192CU Linux Kernel 2.6.18~2.6.38 and Kernel 3.0.8 RTL8192CU http://www.realtek.com.tw/downloads/dow … loads=true
extraire l'archive RTL8192xC_USB_linux_v3.4.4_4749.20121105.zip ce qui génère un dossier nommé RTL8188C_8192C_USB_linux_v3.4.4_4749.20121105

sudo apt-get install build-essential

se placer dans le dossier du driver,je suppose que ce dossier est dans le dossier Téléchargements de ton /home

cd ~/Téléchargements/RTL8188C_8192C_USB_linux_v3.4.4_4749.20121105
 sudo sh install.sh

 

sudo rmmod rtl8192cu
sudo modprobe 8192cu

si le wifi fonctionne,tapes ces 2 commandes

sudo depmod -a
sudo update-initramfs -u

si le wifi fonctionne correctement,fais la suite

gksudo gedit /etc/modprobe.d/blacklist.conf

ajouter à la fin du fichier qui vient de s'ouvrir,une ligne
blacklist rtl8192cu

enregistres et quittes gedit

redemarres le pc
si le wifi ne fonctionne pas aprés redemarrage

gksudo gedit /etc/modules

ajouter à la fin une ligne
8192cu

enregistres et quittes gedit

Dernière modification par chibbata (Le 02/12/2012, à 15:51)

Hors ligne

#6 Le 02/12/2012, à 20:41

jcpain

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Merci Chibatta !
Quelle précision dans les explications !
Je suis cependant surpris (inquiet ?): l'utilisation de xubuntu me semble très élitiste...
Je vais tenter la manip.
Le reste du système semble bien fonctionner et est bcp plus réactif que mon ancien Windows Xp.

Hors ligne

#7 Le 03/12/2012, à 18:20

renyeu

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Super!
N'oublies pas d'insérer [Résolu] devant le titre de ton post d'origine wink
Cdlt
Renyeu

Hors ligne

#8 Le 05/12/2012, à 14:34

jcpain

Re : [Résolu] Comment installer un pilote pour Wifi téléchargé ?

Merci à tous: cela fonctionne !

Hors ligne