Contenu | Rechercher | Menus

Annonce

Si vous rencontrez des soucis à rester connecté sur le forum (ou si vous avez perdu votre mot de passe) déconnectez-vous et reconnectez-vous depuis cette page, en cochant la case "Me connecter automatiquement lors de mes prochaines visites".
Test de l'ISO d'Ubuntu francophone : nous avons besoin de testeurs pour la version francophone d'Ubuntu 14.04. Liens et informations ici.

Attention, une faille de sécurité dans bash a récemment été rapportée, il est recommandé de mettre à jour son système (plus de détails) *** mise à jour 12/10/2014 ***

#51 Le 12/03/2013, à 18:53

lilp

Re : [Résolus] Pbrs Samba

J'ai essayer ac les liens symobliques, mais j'ai le même soucis. Partage vu mais pas accès.

Hors ligne

#52 Le 13/03/2013, à 01:10

toutafai

Re : [Résolus] Pbrs Samba

Donne le retour de

cat /etc/samba/smb.conf
ls -la /media/lilphoenix/Series

tu peux aussi essayer de rajouter ceci dans ton smb.conf (au niveau de la definition des partages)
   

writeable = yes
	force user = lilphoenix

Dernière modification par toutafai (Le 15/03/2013, à 15:22)


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#53 Le 13/03/2013, à 09:47

lilp

Re : [Résolus] Pbrs Samba

COntenue du smb.conf :

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which 
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic 
# errors. 
# A well-established practice is to name the original file
# "smb.conf.master" and create the "real" config file with
# testparm -s smb.conf.master >smb.conf
# This minimizes the size of the really used smb.conf file
# which, according to the Samba Team, impacts performance
# However, use this with caution if your smb.conf file contains nested
# "include" statements. See Debian bug #483187 for a case
# where using a master file is not a good idea.
#

#======================= Global Settings =======================

[global]
wide links = yes
unix extensions = no
## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
	workgroup = WORKGROUP

# server string is the equivalent of the NT Description field
	server string = %h server (Samba, Ubuntu)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
	dns proxy = no

# What naming service and in what order should we use to resolve host names
# to IP addresses
;   name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
	log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
	max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
	syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
	panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
   security = share

# You may wish to use password encryption.  See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.
;	encrypt passwords = yes

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.  
;	passdb backend = tdbsam

	obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
	unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
	passwd program = /usr/bin/passwd %u
	passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
	pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
	map to guest = bad user

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
;   domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the 
# SAMR RPC pipe.  
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.  
; add group script = /usr/sbin/addgroup --force-badname %g

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
#   load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
;   printing = bsd
;   printcap name = /etc/printcap

# CUPS printing.  See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
;	printing = cups
;   printcap name = cups

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
#         SO_RCVBUF=8192 SO_SNDBUF=8192
#   socket options = TCP_NODELAY

# The following parameter is useful only if you have the linpopup package
# installed. The samba maintainer and the linpopup maintainer are
# working to ease installation and configuration of linpopup and samba.
;   message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' &

# Domain Master specifies Samba to be the Domain Master Browser. If this
# machine will be configured as a BDC (a secondary logon server), you
# must set this to 'no'; otherwise, the default behavior is recommended.
#   domain master = auto

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# The following was the default behaviour in sarge,
# but samba upstream reverted the default because it might induce
# performance issues in large organizations.
# See Debian bug #368251 for some of the consequences of *not*
# having this setting and smb.conf(5) for details.
;   winbind enum groups = yes
;   winbind enum users = yes

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;	usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
	usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each 
# user's home director as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server. Un-comment the following parameter
# to make sure that only "username" can connect to \\server\username
# The following parameter makes sure that only "username" can connect
#
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

;	wins support = no
;	wins support = no
	security = share
;	guest ok = no
;	guest account = nobody
	username map = /etc/samba/smbusers
;	guest ok = no
;	guest account = nobody
;	guest ok = no
;	guest account = nobody
wins support = no
[printers]
	comment = All Printers
	browseable = no
	path = /var/spool/samba
	printable = yes
;	guest ok = no
;	read only = yes
	create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers

;	browseable = yes
;	browseable = yes


[Series]
path = /media/lilphoenix/Series
available = yes
browsable = yes
public = yes
writable = yes

[Downloads]
path = /home/lilphoenix/Downloads
available = yes
browsable = yes
public = yes
writable = yes

[Films]
path = /home/lilphoenix/Films
available = yes
browsable = yes
public = yes
writable = yes

ls :

total 520
drwx------  1 lilphoenix lilphoenix   4096 févr.  7 18:11 .
drwxrwxrwx+ 4 root       root         4096 mars  12 18:48 ..
drwx------  1 lilphoenix lilphoenix      0 févr.  7 18:21 BackUp
drwx------  1 lilphoenix lilphoenix  24576 nov.  26 21:21 Docs
drwx------  1 lilphoenix lilphoenix      0 févr.  4 14:09 Incoming
drwx------  1 lilphoenix lilphoenix      0 févr.  4 16:16 OwnCloud
drwx------  1 lilphoenix lilphoenix   4096 mars   3 16:50 Serie
drwx------  1 lilphoenix lilphoenix 495616 janv. 23 09:03 Zik

Hors ligne

#54 Le 13/03/2013, à 20:33

toutafai

Re : [Résolus] Pbrs Samba

oups, une petite erreur, c'est pas le resultat que je voulais.... peux tu donner le retour de

ls -la /media

Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#55 Le 13/03/2013, à 21:56

lilp

Re : [Résolus] Pbrs Samba

Voici le retour :

total 16
drwxr-xr-x   3 root root 4096 févr.  5 22:55 .
drwxr-xr-x  28 root root 4096 févr. 22 10:32 ..
-rw-r--r--   1 root root   49 nov.  18 17:48 .created_by_python-fstab
drwxrwxrwx+  4 root root 4096 mars  12 18:48 lilphoenix

Hors ligne

#56 Le 14/03/2013, à 17:56

toutafai

Re : [Résolus] Pbrs Samba

L'erreur vient de ton fichier smb.conf !
Ce n'est pas

[Series]
path = /media/lilphoenix/Series

mais

[Series]
path = /media/lilphoenix/Serie

Concernant les autres partages, quand je regarde ton smb.conf sur ton post #6, ils pointent vers /media/lilphoenix/Films et non pas vers /home/lilphoenix/Films

Corrige tout cela dans le smb.conf et redemarre samba


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#57 Le 14/03/2013, à 20:54

lilp

Re : [Résolus] Pbrs Samba

Je suis désolé, mais mon dossier Série et Fims leurs chemins et orthographes sont bien :

/media/lilphoenix/Films
/media/lilphoenix/Series

Et le dossier Films contient deux sous dossiers "Film" et "Video"
Et Series contient "Serie", "Zik"...

Hors ligne

#58 Le 14/03/2013, à 22:00

toutafai

Re : [Résolus] Pbrs Samba

oui, mais non ! tu les fait pointer vers /home..... dans le fichier smb.conf


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#59 Le 14/03/2013, à 22:50

lilp

Re : [Résolus] Pbrs Samba

Dans le fichier smb.conf, je doit donc mettre /home/lilphoenix/Fims et /home/lilphoenix/Series?

Hors ligne

#60 Le 15/03/2013, à 15:28

toutafai

Re : [Résolus] Pbrs Samba

Non puisque ton partage est physiquement sur
/media/lilphoenix/Films
dans ton smb.conf, tu dois avoir
path = /media/lilphoenix/Films

PS :
1/ quand je regarde ton retour post #53 à la commande "ls -la /media/lilphoenix/Series" , si je comprends bien l'organisation de ton disque, tu as un dossier /media/lilphoenix/Series qui contient lui-même d'autre sous-dossier, dont 1 qui se nomme Serie    ....d'ou ma confusion concernant ce partage

2/ J'avais fait une erreur sur mon post #52, au niveau de la dernier ligne "    force user = lilphoen" (j'ai corrigé mon post) et la bonne syntaxe était biensur

	force user = lilphoenix

Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#61 Le 15/03/2013, à 18:55

lilp

Re : [Résolus] Pbrs Samba

Oui, j'avais corriger le "lilphoen" en "lilphoenix".
Et oui, mon dossier peut prêté a confusion car effectivement, le disque dur se nomme "Series" et contient ou dossier "Serie".

Hors ligne

#62 Le 15/03/2013, à 19:00

lilp

Re : [Résolus] Pbrs Samba

Je te re-fournie le smb.conf :

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which 
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic 
# errors. 
# A well-established practice is to name the original file
# "smb.conf.master" and create the "real" config file with
# testparm -s smb.conf.master >smb.conf
# This minimizes the size of the really used smb.conf file
# which, according to the Samba Team, impacts performance
# However, use this with caution if your smb.conf file contains nested
# "include" statements. See Debian bug #483187 for a case
# where using a master file is not a good idea.
#

#======================= Global Settings =======================

[global]
wide links = yes
unix extensions = no
## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
	workgroup = WORKGROUP

# server string is the equivalent of the NT Description field
	server string = %h server (Samba, Ubuntu)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
	dns proxy = no

# What naming service and in what order should we use to resolve host names
# to IP addresses
;   name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
	log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
	max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
	syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
	panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
   security = share

# You may wish to use password encryption.  See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.
;	encrypt passwords = yes

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.  
;	passdb backend = tdbsam

	obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
	unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
	passwd program = /usr/bin/passwd %u
	passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
	pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
	map to guest = bad user

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
;   domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the 
# SAMR RPC pipe.  
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.  
; add group script = /usr/sbin/addgroup --force-badname %g

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
#   load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
;   printing = bsd
;   printcap name = /etc/printcap

# CUPS printing.  See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
;	printing = cups
;   printcap name = cups

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
#         SO_RCVBUF=8192 SO_SNDBUF=8192
#   socket options = TCP_NODELAY

# The following parameter is useful only if you have the linpopup package
# installed. The samba maintainer and the linpopup maintainer are
# working to ease installation and configuration of linpopup and samba.
;   message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' &

# Domain Master specifies Samba to be the Domain Master Browser. If this
# machine will be configured as a BDC (a secondary logon server), you
# must set this to 'no'; otherwise, the default behavior is recommended.
#   domain master = auto

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# The following was the default behaviour in sarge,
# but samba upstream reverted the default because it might induce
# performance issues in large organizations.
# See Debian bug #368251 for some of the consequences of *not*
# having this setting and smb.conf(5) for details.
;   winbind enum groups = yes
;   winbind enum users = yes

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;	usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
	usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each 
# user's home director as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server. Un-comment the following parameter
# to make sure that only "username" can connect to \\server\username
# The following parameter makes sure that only "username" can connect
#
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

;	wins support = no
;	wins support = no
	security = share
;	guest ok = no
;	guest account = nobody
	username map = /etc/samba/smbusers
;	guest ok = no
;	guest account = nobody
;	guest ok = no
;	guest account = nobody
wins support = no
[printers]
	comment = All Printers
	browseable = no
	path = /var/spool/samba
	printable = yes
;	guest ok = no
;	read only = yes
	create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers

;	browseable = yes
;	browseable = yes


[Series]
path = /media/lilphoenix/Series
available = yes
browsable = yes
public = yes
writable = yes
force user = lilphoenix

[Downloads]
path = /home/lilphoenix/Downloads
available = yes
browsable = yes
public = yes
writable = yes
force user = lilphoenix

[Films]
path = /media/lilphoenix/Films
available = yes
browsable = yes
public = yes
writable = yes
force user = lilphoenix

Et le contenue du disque Series :

total 520
drwx------  1 lilphoenix lilphoenix   4096 févr.  7 18:11 .
drwxrwxrwx+ 4 root       root         4096 mars  14 23:00 ..
drwx------  1 lilphoenix lilphoenix      0 févr.  7 18:21 BackUp
drwx------  1 lilphoenix lilphoenix  24576 nov.  26 21:21 Docs
drwx------  1 lilphoenix lilphoenix      0 févr.  4 14:09 Incoming
drwx------  1 lilphoenix lilphoenix      0 févr.  4 16:16 OwnCloud
drwx------  1 lilphoenix lilphoenix   4096 mars   3 16:50 Serie
drwx------  1 lilphoenix lilphoenix 495616 janv. 23 09:03 Zik

Mais toujours impossible de rentrer dans le dossier.

Hors ligne

#63 Le 17/03/2013, à 21:43

toutafai

Re : [Résolus] Pbrs Samba

Salut,

Idem que le weekend dernier pour le délai de réponse :-)

a mon avis tu as un probleme de droit sur /media/lilphoenix car apparatient a l'utilisateur root du groupe root, alors que tes sous dossier appartiennet bien a lilphoenix... essaye cela

sudo chown lilphoenix /media/lilphoenix

remedarre et re test...

si cela ne fonctionne toujours pas :

sudo umount /media/lilphoenix
sudo rmdir/media/lilphoenix

reboot


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#64 Le 18/03/2013, à 19:45

lilp

Re : [Résolus] Pbrs Samba

Voici le retour de ces commandes

lilphoenix@Serveur:~$ sudo umount /media/lilphoenix
[sudo] password for lilphoenix: 
umount : /media/lilphoenix : n'est pas monté
lilphoenix@Serveur:~$ sudo rmdir/media/lilphoenix
sudo: rmdir/media/lilphoenix: command not found
lilphoenix@Serveur:~$ sudo rmdir /media/lilphoenix
rmdir: échec de suppression de «/media/lilphoenix»: Le dossier n'est pas vide
lilphoenix@Serveur:~$ 

Hors ligne

#65 Le 19/03/2013, à 21:44

toutafai

Re : [Résolus] Pbrs Samba

rooo, purée de purée....soit ton disque n'est pas monté, soit c'est pas le bon chemin de montage, d'ou la question ; comment est-il sensé être monté :
automatiquement au démarrage (via le fichier /etc/fstab) ou tu le monte à la main en double cliquant dessus par exemple depuis nautilus(=l'explorateu)  ?
il me semble que tu m'as dis que c'etait un disque USB, mais je suis plus sur de moi...(confirme-moi ou pas)
Assure-toi que le disque est bien "monté" (= que tu peux y acceder depuis le pc sur lequel est branché ton disque) et donne le retour de

sudo mount -l # C'est un petit L
sudo fdisk -l # C'est un petit L
cat /etc/fstab

Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#66 Le 19/03/2013, à 22:11

lilp

Re : [Résolus] Pbrs Samba

Ce n'est pas un disque en USB, branché en Sata, et je le monte manuellement en double cliquant dessus, mais j'aimerais bien ne pas avoir à le faire et qu'il se monte tout seul.
Voici les retours :

lilphoenix@Serveur:~$ sudo mount -l
[sudo] password for lilphoenix: 
/dev/sdc1 on / type ext4 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
none on /sys/fs/fuse/connections type fusectl (rw)
none on /sys/kernel/debug type debugfs (rw)
none on /sys/kernel/security type securityfs (rw)
udev on /dev type devtmpfs (rw,mode=0755)
devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620)
tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755)
none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880)
none on /run/shm type tmpfs (rw,nosuid,nodev)
none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755)
gvfsd-fuse on /run/user/lilphoenix/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=lilphoenix)
/dev/sda1 on /media/lilphoenix/Films type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) [Films]
/dev/sdb1 on /media/lilphoenix/Series type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) [Series]
lilphoenix@Serveur:~$ sudo fdisk -l

Disk /dev/sda: 2000.4 GB, 2000398934016 bytes
255 têtes, 63 secteurs/piste, 243201 cylindres, total 3907029168 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Identifiant de disque : 0x00046ef1

Périphérique Amorce  Début        Fin      Blocs     Id  Système
/dev/sda1            2048  3907028991  1953513472    7  HPFS/NTFS/exFAT

Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes
255 têtes, 63 secteurs/piste, 243201 cylindres, total 3907029168 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Identifiant de disque : 0x633d5783

Périphérique Amorce  Début        Fin      Blocs     Id  Système
/dev/sdb1            2048  3907028991  1953513472    7  HPFS/NTFS/exFAT

Disk /dev/sdc: 250.1 GB, 250059350016 bytes
255 têtes, 63 secteurs/piste, 30401 cylindres, total 488397168 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Identifiant de disque : 0x00024ce4

Périphérique Amorce  Début        Fin      Blocs     Id  Système
/dev/sdc1   *        2048   480015719   240006836   83  Linux
/dev/sdc2       480018430   488396799     4189185    5  Étendue
/dev/sdc5       480018432   488396799     4189184   82  partition d'échange Linux / Solaris
lilphoenix@Serveur:~$ cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
# / was on /dev/sda1 during installation
UUID=6a0448a8-0488-47f9-a1c5-a0a3e1dd9fbe /               ext4    errors=remount-ro 0       1
# swap was on /dev/sda5 during installation
UUID=2a45ef7c-e01e-4dfd-8f50-5a5ff181675a none            swap    sw              0       0

Hors ligne

#67 Le 20/03/2013, à 20:46

toutafai

Re : [Résolus] Pbrs Samba

Ah oui, je comprend mieux ; tu as 3 disques en fait : Films est dans le 1 er disque, Series dans le 2 em, et ton ubuntu sur le troisième...(un dual-boot Windows/Ubuntu, avoue ? lol)
bon, on vas d'abord s'occuper de monter les 2 disques automatiquement. :
Commence par les démonter : ouvre nautilus, et clic droit sur le disque Film, puis choisit "demonter", idem pour le disque Series, puis

cd /media
sudo mkdir Films && sudo chown lilphoenix Films
sudo mkdir Series && sudo chown lilphoenix Series

Edite le fichier /etc/fstab avec cette commande (attention a ce que tu fait dans ce fichier)

sudo gedit /etc/fstab

A la fin du fichier tu rajoute ces 2 lignes :

/dev/sda1  /media/Films  ntfs-3g  rw,user,auto,gid=100,uid=1000,nls=utf8,umask=002        0       0
/dev/sdb1  /media/Series  ntfs-3g  rw,user,auto,gid=100,uid=1000,nls=utf8,umask=002        0       0

Enregistre les modifications et ferme gedit, puis entre la commande suivante :

sudo mount -a

Tes disque ont du se monter automatiquement, vérifie avec un

sudo mount -l # tjrs un petit L, ce doit te lister ton /dev/sda1 et ton /dev/sdb1

Si c'est ok, edite ton fichier /etc/samba/smb.conf et dans les section [Film] tu change la variable PATH de chaque partage, ce qui te donne

[Films]
path = /media/Films
......
[Series]
path = /media/Series
....

Enfin reboot, et test ton partage qui doit fonctionner

Dernière modification par toutafai (Le 20/03/2013, à 20:48)


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

#68 Le 21/03/2013, à 09:41

lilp

Re : [Résolus] Pbrs Samba

Dual boot ac Windows sur mon petit serveur Multimédia, DL, et Cloud? Non sa serait un crime, juste voulus réserver un disque pour l'OS et la partie téléchargements, et les Data sur d'autres disques.

Hors ligne

#69 Le 21/03/2013, à 10:01

lilp

Re : [Résolus] Pbrs Samba

smile nickel, cela à fonctionner. En les montant dans /media sa a fonctionner.
Cela était un pbrs de droit au final?

Hors ligne

#70 Le 21/03/2013, à 10:21

lilp

Re : [Résolus] Pbrs Samba

Je te doit un très grand merci. Car passé beaucoup de temps sur mon problème que tu a résolus, et en plus, tu m'a appris plusieurs choses (éditer mon fichier smb.conf, monté des disques automatiquement ou je veut, afficher tout un tas d'infos).

Hors ligne

#71 Le 21/03/2013, à 12:52

toutafai

Re : [Résolus] Pbrs Samba

oui, je pense que c'etait un probleme de droit sur les dossier de partage et sur le chamin d'acces aux partage. Voila, pas de probleme pour l'aide, le forum est la pour cela.

bonne continuation a toi.


Ubuntu Server 12.04 x32 sur IBM P4. - XP / Seven / Ubuntu 14.04 x64 sur Lenovo ThinkPad. Purée d'unity...difficile de s'y faire - canon MG5350 - Logitech Quickcam 3000 - TNT Intuix S800 - Freebox v6 révolution (Trop de la balle !!!)
Utilisateur d'Ubuntu depuis novembre 2006.
23 PC libérés grâce aux OS libres...et de 24 et quel 24 ...car pc au taff et pour le taff ^^

Hors ligne

Haut de page ↑