Contenu | Rechercher | Menus

Annonce

Si vous rencontrez des soucis à rester connecté sur le forum (ou si vous avez perdu votre mot de passe) déconnectez-vous et reconnectez-vous depuis cette page, en cochant la case "Me connecter automatiquement lors de mes prochaines visites".
Test de l'ISO d'Ubuntu francophone : nous avons besoin de testeurs pour la version francophone d'Ubuntu 14.04. Liens et informations ici.

Attention, une faille de sécurité dans bash a récemment été rapportée, il est recommandé de mettre à jour son système (plus de détails) *** mise à jour 12/10/2014 ***

#26 Le 18/12/2007, à 22:13

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

je retrouve qqch de normal pour :

$ ndiswrapper -l
Installed ndis drivers:
net111v2                driver present, hardware present

j'avais oublier de désactiver du network manager... Je l'avais oublié celui-là ... J'ai essayé de resuivre le tuto sans succès.

$ sudo ndiswrapper -m
Password:
modprobe config already contains alias directive

$ sudo modprobe ndiswrapper

et quand je réinitialise le rsx, il oublie mon dongle, c'est parce que je l'ai désactivé dans "interfaces",

$ sudo /etc/init.d/networking restart
 * Reconfiguring network interfaces... Internet Systems Consortium DHCP Client V3.0.3
Copyright 2004-2005 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP

Listening on LPF/eth0/00:c0:9f:35:51:8e
Sending on   LPF/eth0/00:c0:9f:35:51:8e
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPOFFER from 192.168.0.1
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.0.1
bound to 192.168.0.2 -- renewal in 32470 seconds.
                                                                         [ ok ]

je retrouve ma connexion eth0, waouh, mais c'est pas trop l'objectif. J'ai enlevé le commentaire de wlan0 (toujours dans "interfaces"), et là , rien de plus quand restart connexion hmm

Dernière modification par spip59 (Le 18/12/2007, à 22:16)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#27 Le 18/12/2007, à 22:56

cflam69

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

cflam69 a écrit :

... soit un module interfère avec ndiswrapper.
Le mieux pour voir, c'est de copier/coller (avec les balises code par pitié roll) un

dmesg

juste après avoir booté avec la clef et tout le toutim branché.
On devrait voir si ndiswrapper est gêné aux entournures.

C'est toujours valable. Apparemment, ndiswrapper et ton driver son ok. Maintenant, reste à voir les autre modules donc un p'tit dmesg après démarrage svp.


La liberté ne s'use que si l'on ne s'en sert pas.

Hors ligne

#28 Le 18/12/2007, à 23:13

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

ok, autant pour moi :

$ dmesg
[17179569.184000] Linux version 2.6.15-29-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Mon Sep 24 17:18:25 UTC 2007
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[17179569.184000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000001fdf0000 (usable)
[17179569.184000]  BIOS-e820: 000000001fdf0000 - 000000001fdfb000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000001fdfb000 - 000000001fe00000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000001fe00000 - 0000000020000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 509MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f6e10
[17179569.184000] On node 0 totalpages: 130544
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 126448 pages, LIFO batch:31
[17179569.184000]   HighMem zone: 0 pages, LIFO batch:0
[17179569.184000] DMI present.
[17179569.184000] ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6eb0
[17179569.184000] ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x1fdf67ec
[17179569.184000] ACPI: FADT (v001 SiS    M650     0x06040000 PTL  0x00000001) @ 0x1fdfaf14
[17179569.184000] ACPI: MADT (v001 PTLTD         APIC   0x06040000  LTP 0x00000000) @ 0x1fdfaf88
[17179569.184000] ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x1fdfafd8
[17179569.184000] ACPI: DSDT (v001 PTLTD      650M 0x06040000 MSFT 0x0100000e) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x8008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hdc3 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 32768 bytes)
[17179569.184000] Detected 2600.479 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179571.036000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179571.036000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)[17179571.048000] Memory: 507060k/522176k available (1977k kernel code, 14452k reserved, 605k data, 288k init, 0k highmem)
[17179571.048000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179571.128000] Calibrating delay using timer specific routine.. 5204.92 BogoMIPS (lpj=10409844)
[17179571.128000] Security Framework v1.0.0 initialized
[17179571.128000] SELinux:  Disabled at boot.
[17179571.128000] Mount-cache hash table entries: 512
[17179571.128000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179571.128000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[17179571.128000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179571.128000] CPU: L2 cache: 512K
[17179571.128000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
[17179571.128000] mtrr: v2.0 (20020519)
[17179571.128000] CPU: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
[17179571.128000] Enabling fast FPU save and restore... done.
[17179571.128000] Enabling unmasked SIMD FPU exception support... done.
[17179571.128000] Checking 'hlt' instruction... OK.
[17179571.144000] checking if image is initramfs... it is
[17179571.668000] Freeing initrd memory: 6666k freed
[17179571.680000] ACPI: Looking for DSDT ... not found!
[17179571.736000] ENABLING IO-APIC IRQs
[17179571.736000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179571.880000] NET: Registered protocol family 16
[17179571.880000] EISA bus registered
[17179571.880000] ACPI: bus type pci registered
[17179571.880000] PCI: PCI BIOS revision 2.10 entry at 0xfd9c6, last bus=1
[17179571.880000] PCI: Using configuration type 1
[17179571.880000] ACPI: Subsystem revision 20051216
[17179571.904000] ACPI: Interpreter enabled
[17179571.904000] ACPI: Using IOAPIC for interrupt routing
[17179571.904000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179571.904000] PCI: Probing PCI hardware (bus 00)
[17179571.904000] Uncovering SIS962 that hid as a SIS503 (compatible=1)
[17179571.904000] Enabling SiS 96x SMBus.
[17179571.904000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
[17179571.904000] Boot video device is 0000:01:00.0
[17179571.904000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179571.908000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKA._CRS] (Node dfdda460), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKA] (IRQs 7 10) *0
[17179571.908000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3) *0, disabled.
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKC._CRS] (Node dfdda260), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKC] (IRQs 5) *0
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKD._CRS] (Node dfddaf80), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKD] (IRQs 7 10) *0
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKE._CRS] (Node dfddae80), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKE] (IRQs 7 10) *0
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKF._CRS] (Node dfddad80), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKF] (IRQs 7 10) *0
[17179571.908000]     ACPI-0216: *** Error: Return object type is incorrect [\_SB_.PCI0.LPCB.LNKG._CRS] (Node dfddac80), AE_TYPE
[17179571.908000] ACPI: PCI Interrupt Link [LNKG] (IRQs 7 10) *0
[17179571.908000] ACPI: PCI Interrupt Link [LNKH] (IRQs 7 10) *0, disabled.
[17179571.912000] ACPI: Embedded Controller [EC0] (gpe 25) interrupt mode.
[17179571.928000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179571.928000] pnp: PnP ACPI init
[17179571.940000] pnp: PnP ACPI: found 11 devices
[17179571.940000] PnPBIOS: Disabled by ACPI PNP
[17179571.940000] PCI: Using ACPI for IRQ routing
[17179571.940000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179571.944000] pnp: 00:07: ioport range 0x8000-0x808f could not be reserved
[17179571.944000] pnp: 00:07: ioport range 0x8090-0x80ff has been reserved
[17179571.944000] pnp: 00:07: ioport range 0x8100-0x811f has been reserved
[17179571.944000] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[17179571.944000] pnp: 00:07: ioport range 0xfe00-0xfe00 has been reserved
[17179571.944000] PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:01:00.0
[17179571.944000] PCI: Bridge: 0000:00:01.0
[17179571.944000]   IO window: disabled.
[17179571.944000]   MEM window: e5000000-e5ffffff
[17179571.944000]   PREFETCH window: e8000000-efffffff
[17179571.944000] PCI: Bus 2, cardbus bridge: 0000:00:0a.0
[17179571.944000]   IO window: 00002400-000024ff
[17179571.944000]   IO window: 00002800-000028ff
[17179571.944000]   PREFETCH window: 30000000-31ffffff
[17179571.944000]   MEM window: 32000000-33ffffff
[17179571.944000] PCI: Enabling device 0000:00:0a.0 (0000 -> 0003)
[17179571.944000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 169
[17179571.944000] Simple Boot Flag at 0x36 set to 0x1
[17179571.944000] audit: initializing netlink socket (disabled)
[17179571.944000] audit(1198015826.944:1): initialized
[17179571.944000] VFS: Disk quotas dquot_6.5.1
[17179571.944000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179571.944000] Initializing Cryptographic API
[17179571.944000] io scheduler noop registered
[17179571.944000] io scheduler anticipatory registered
[17179571.944000] io scheduler deadline registered
[17179571.944000] io scheduler cfq registered
[17179571.944000] isapnp: Scanning for PnP cards...
[17179572.296000] isapnp: No Plug & Play device found
[17179572.312000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[17179572.320000] i8042.c: Detected active multiplexing controller, rev 1.1.
[17179572.320000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[17179572.320000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[17179572.320000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[17179572.324000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[17179572.324000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179572.324000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179572.324000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179572.324000] 00:01: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179572.324000] PCI: Enabling device 0000:00:02.6 (0000 -> 0001)
[17179572.324000] ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 177
[17179572.324000] ACPI: PCI interrupt for device 0000:00:02.6 disabled
[17179572.324000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179572.324000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179572.324000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179572.324000] mice: PS/2 mouse device common for all mice
[17179572.328000] EISA: Probing bus 0 at eisa.0
[17179572.328000] Cannot allocate resource for EISA slot 1
[17179572.328000] Cannot allocate resource for EISA slot 2
[17179572.328000] Cannot allocate resource for EISA slot 8
[17179572.328000] EISA: Detected 0 cards.
[17179572.328000] NET: Registered protocol family 2
[17179572.368000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179572.368000] TCP established hash table entries: 16384 (order: 4, 65536 bytes)
[17179572.368000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[17179572.368000] TCP: Hash tables configured (established 16384 bind 16384)
[17179572.368000] TCP reno registered
[17179572.368000] TCP bic registered
[17179572.368000] NET: Registered protocol family 1
[17179572.368000] NET: Registered protocol family 8
[17179572.368000] NET: Registered protocol family 20
[17179572.368000] Using IPI Shortcut mode
[17179572.368000] ACPI wakeup devices:
[17179572.368000] MDEM USB1 USB2 USB3  LAN  LID
[17179572.368000] ACPI: (supports S0 S3 S4 S5)
[17179572.368000] Freeing unused kernel memory: 288k freed
[17179572.376000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179572.412000] vga16fb: initializing
[17179572.412000] vga16fb: mapped to 0xc00a0000
[17179572.568000] Console: switching to colour frame buffer device 80x25
[17179572.568000] fb0: VGA16 VGA frame buffer device
[17179573.724000] Capability LSM initialized
[17179574.764000] ACPI: Thermal Zone [THRM] (44 C)
[17179575.320000] SIS5513: IDE controller at PCI slot 0000:00:02.5
[17179575.320000] ACPI: PCI Interrupt 0000:00:02.5[A]: no GSI
[17179575.320000] SIS5513: chipset revision 0
[17179575.320000] SIS5513: not 100% native mode: will probe irqs later
[17179575.320000] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
[17179575.320000]     ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio
[17179575.320000]     ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio
[17179575.320000] Probing IDE interface ide0...
[17179576.056000] hda: MATSHITADVD-RAM UJ-811, ATAPI CD/DVD-ROM drive
[17179576.392000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179576.392000] Probing IDE interface ide1...
[17179576.680000] hdc: ST380012A, ATA DISK drive
[17179577.352000] ide1 at 0x170-0x177,0x376 on irq 15
[17179577.368000] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179577.368000] Uniform CD-ROM driver Revision: 3.20
[17179577.392000] hdc: max request size: 1024KiB
[17179577.396000] hdc: 156301488 sectors (80026 MB) w/1024KiB Cache, CHS=16383/255/63, UDMA(100)
[17179577.396000] hdc: cache flushes supported
[17179577.396000]  hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 >
[17179578.708000] ieee1394: Initialized config rom entry `ip1394'
[17179578.708000] ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
[17179578.708000] PCI: Enabling device 0000:00:02.3 (0000 -> 0002)
[17179578.708000] ACPI: PCI Interrupt 0000:00:02.3[b] -> GSI 17 (level, low) -> IRQ 169
[17179578.708000] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
[17179578.760000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169]  MMIO=[e4000000-e40007ff]  Max Packet=[2048]
[17179578.780000] usbcore: registered new driver usbfs
[17179578.780000] usbcore: registered new driver hub
[17179578.784000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179578.784000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 185
[17179578.784000] ohci_hcd 0000:00:03.0: OHCI Host Controller
[17179578.784000] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[17179578.784000] ohci_hcd 0000:00:03.0: irq 185, io mem 0xe4001000
[17179578.796000] hub 1-0:1.0: USB hub found
[17179578.796000] hub 1-0:1.0: 2 ports detected
[17179578.900000] ACPI: PCI Interrupt 0000:00:03.1[b] -> GSI 21 (level, low) -> IRQ 193
[17179578.900000] ohci_hcd 0000:00:03.1: OHCI Host Controller
[17179579.120000] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[17179579.120000] ohci_hcd 0000:00:03.1: irq 193, io mem 0xe4002000
[17179579.176000] hub 2-0:1.0: USB hub found
[17179579.176000] hub 2-0:1.0: 2 ports detected
[17179579.280000] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 201
[17179579.280000] ohci_hcd 0000:00:03.2: OHCI Host Controller
[17179579.500000] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[17179579.500000] ohci_hcd 0000:00:03.2: irq 201, io mem 0xe4003000
[17179579.556000] hub 3-0:1.0: USB hub found
[17179579.556000] hub 3-0:1.0: 2 ports detected
[17179579.660000] PCI: Enabling device 0000:00:03.3 (0000 -> 0002)
[17179579.660000] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 209
[17179579.660000] ehci_hcd 0000:00:03.3: EHCI Host Controller
[17179579.660000] PCI: cache line size of 128 is not supported by device 0000:00:03.3
[17179579.660000] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[17179579.660000] ehci_hcd 0000:00:03.3: irq 209, io mem 0xe4004000
[17179579.660000] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179579.660000] hub 4-0:1.0: USB hub found
[17179579.660000] hub 4-0:1.0: 6 ports detected
[17179579.884000] Attempting manual resume
[17179579.928000] EXT3-fs: mounted filesystem with ordered data mode.
[17179579.944000] kjournald starting.  Commit interval 5 seconds
[17179580.040000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00c09f000014f779]
[17179580.068000] usb 4-3: new high speed USB device using ehci_hcd and address 2
[17179580.692000] usb 2-2: new low speed USB device using ohci_hcd and address 3[17179590.776000] i2c-sis96x version 1.0.0
[17179590.776000] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100
[17179590.800000] Linux agpgart interface v0.101 (c) Dave Jones
[17179590.828000] agpgart: Detected SiS 650 chipset
[17179590.828000] agpgart: unable to determine aperture size.
[17179590.828000] agpgart: agp_backend_initialize() failed.
[17179590.828000] agpgart-sis: probe of 0000:00:00.0 failed with error -22
[17179590.964000] sis900.c: v1.08.09 Sep. 19 2005
[17179590.964000] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 217
[17179590.968000] 0000:00:04.0: Altimata AC101LF PHY transceiver found at address 1.
[17179590.980000] 0000:00:04.0: Using transceiver found at address 1 as default
[17179590.980000] eth0: SiS 900 PCI Fast Ethernet at 0x2000, IRQ 217, 00:c0:9f:35:51:8e.
[17179591.156000] PCI: Enabling device 0000:00:02.7 (0000 -> 0001)
[17179591.156000] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 177
[17179591.184000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179591.520000] Real Time Clock Driver v1.12
[17179591.596000] Floppy drive(s): fd0 is 1.44M
[17179591.600000] input: PC Speaker as /class/input/input1
[17179591.612000] FDC 0 is a post-1991 82077
[17179591.980000] intel8x0_measure_ac97_clock: measured 55444 usecs
[17179591.980000] intel8x0: clocking to 48000
[17179591.980000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179591.980000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 169
[17179591.980000] Yenta: CardBus bridge found at 0000:00:0a.0 [1025:0028]
[17179591.980000] Yenta O2: res at 0x94/0xD4: 00/ca
[17179591.980000] Yenta O2: enabling read prefetch/write burst
[17179592.024000] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x1d48b1, caps: 0x904713/0x4006
[17179592.092000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[17179592.108000] Yenta: ISA IRQ mask 0x0cb8, PCI irq 169
[17179592.108000] Socket status: 30000007
[17179592.212000] nvidia: module license 'NVIDIA' taints kernel.
[17179592.216000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 225
[17179592.216000] NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-8776  Mon Oct 16 21:56:04 PDT 2006
[17179592.736000] usbcore: registered new driver hiddev
[17179592.748000] input: KYE NetScroll+ Traveler as /class/input/input3
[17179592.748000] input: USB HID v1.10 Mouse [KYE NetScroll+ Traveler] on usb-0000:00:03.1-2
[17179592.748000] usbcore: registered new driver usbhid
[17179592.748000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179592.752000] ts: Compaq touchscreen protocol output
[17179593.084000] cs: IO port probe 0x100-0x3af: excluding 0x1c0-0x1cf 0x378-0x37f
[17179593.088000] cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
[17179593.088000] cs: IO port probe 0x820-0x8ff: clean.
[17179593.088000] cs: IO port probe 0xc00-0xcf7: clean.
[17179593.088000] cs: IO port probe 0xa00-0xaff: clean.
[17179593.304000] parport: PnPBIOS parport detected.
[17179593.304000] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179594.360000] lp0: using parport0 (interrupt-driven).
[17179594.372000] NET: Registered protocol family 17
[17179594.416000] SCSI subsystem initialized
[17179594.424000] sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
[17179594.424000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179594.424000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179594.472000] ndiswrapper version 1.8 loaded (preempt=yes,smp=no)
[17179594.508000] ndiswrapper: driver net111v2 (NETGEAR Inc.,3/16/2006,5.1213.06.0316) loaded
[17179595.296000] eth0: Media Link On 100mbps full-duplex
[17179598.168000] wlan0: vendor: 'Realtek RTL8187 Wireless LAN USB NIC                            '
[17179598.168000] wlan0: ndiswrapper ethernet device 00:18:4d:bd:1e:97 using driver net111v2, 0846:6A00.F.conf
[17179598.168000] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[17179598.168000] usbcore: registered new driver ndiswrapper
[17179598.212000] Adding 1044184k swap on /dev/hdc6.  Priority:-1 extents:1 across:1044184k
[17179598.392000] EXT3 FS on hdc3, internal journal
[17179598.568000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179598.568000] md: bitmap version 4.39
[17179599.196000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179600.332000] NET: Registered protocol family 10
[17179600.332000] lo: Disabled Privacy Extensions
[17179600.332000] IPv6 over IPv4 tunneling driver
[17179600.452000] cdrom: open failed.
[17179610.712000] eth0: no IPv6 routers present
[17179611.632000] kjournald starting.  Commit interval 5 seconds
[17179611.632000] EXT3 FS on hdc5, internal journal
[17179611.632000] EXT3-fs: mounted filesystem with ordered data mode.
[17179611.676000] NTFS driver 2.1.25 [Flags: R/O MODULE].
[17179611.760000] NTFS volume version 3.1.
[17179613.256000] ACPI: AC Adapter [ACAD] (on-line)
[17179613.304000] ACPI: Battery Slot [BAT1] (battery present)
[17179613.388000] ACPI: Power Button (FF) [PWRF]
[17179613.388000] ACPI: Power Button (CM) [PWRB]
[17179613.388000] ACPI: Lid Switch [LID]
[17179613.388000] ACPI: Sleep Button (CM) [SLPB]
[17179613.492000] ibm_acpi: ec object not found
[17179613.524000] pcc_acpi: loading...
[17179613.624000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[17179624.456000] ppdev: user-space parallel port driver
[17179624.876000] apm: BIOS not found.
[17179625.508000] ip_tables: (C) 2000-2002 Netfilter core team
[17179625.604000] Netfilter messages via NETLINK v0.30.
[17179625.624000] ip_conntrack version 2.4 (4079 buckets, 32632 max) - 232 bytes per conntrack
[17179628.348000] Bluetooth: Core ver 2.8
[17179628.348000] NET: Registered protocol family 31
[17179628.348000] Bluetooth: HCI device and connection manager initialized
[17179628.348000] Bluetooth: HCI socket layer initialized
[17179628.384000] Bluetooth: L2CAP ver 2.8
[17179628.384000] Bluetooth: L2CAP socket layer initialized
[17179628.388000] Bluetooth: RFCOMM socket layer initialized
[17179628.388000] Bluetooth: RFCOMM TTY layer initialized
[17179628.388000] Bluetooth: RFCOMM ver 1.7

Dernière modification par spip59 (Le 18/12/2007, à 23:14)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#29 Le 19/12/2007, à 00:22

cflam69

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

4.424000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179594.424000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179594.472000] ndiswrapper version 1.8 loaded (preempt=yes,smp=no)
[17179594.508000] ndiswrapper: driver net111v2 (NETGEAR Inc.,3/16/2006,5.1213.06.0316) loaded
[17179595.296000] eth0: Media Link On 100mbps full-duplex
[17179598.168000] wlan0: vendor: 'Realtek RTL8187 Wireless LAN USB NIC                            '

[17179598.168000] wlan0: ndiswrapper ethernet device 00:18:4d:bd:1e:97 using driver net111v2, 0846:6A00.F.conf
[17179598.168000] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[17179598.168000] usbcore: registered new driver ndiswrapper

Donc ton ndiswrapper charge bien un driver, qui semble être le bon.
Moi, sous Gutsy, ça donne :

[   60.492337] ndiswrapper version 1.45 loaded (smp=yes)
[   60.691155] usb 5-4: reset high speed USB device using ehci_hcd and address 3
[   60.877521] ndiswrapper: driver netwg111 (NETGEAR, Inc.,06/04/2004, 3.0.18.201) loaded
[   61.982985] wlan0: ethernet device xx:xx:xx:xx:xx:xx using NDIS driver: netwg111, version: 0x30012, NDIS version: 0x501, vendor: 'NETGEAR WG111 802.11g Wireless USB2.0 Adapter', 0846:4240.F.conf
[   61.983091] wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
[   61.992471] usbcore: registered new interface driver ndiswrapper

Par contre il semble perdu le tien. Un coup c'est ndiswrapper, un coup RTL8187 ... je pense qu'il est mal blacklisté.
Essaye la liste dans un sens différents (parfois ça joue), genre :

blacklist islsm_pci
blacklist islsm
blacklist islsm_usb
blacklist prism2_usb
blacklist rtl8187
blacklist r8187b

TU peux aussi faire des essai vbia la commande rmmod.

Dernière modification par cflam69 (Le 19/12/2007, à 00:25)


La liberté ne s'use que si l'on ne s'en sert pas.

Hors ligne

#30 Le 19/12/2007, à 00:25

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

en fait, j'ai pas la même liste que toi...

blacklist rtl8187
blacklist r8187
blacklist islsmusb
blacklist islsm
blacklist islsm_usb
blacklist prism54usb
blacklist p54usb
blacklist p54common

Kubuntu Desktop 12.04  64 Bits

Hors ligne

#31 Le 19/12/2007, à 00:27

cflam69

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

Si mais moi j'ai rajouté

blacklist prism54usb
blacklist p54usb
blacklist p54common

sous Gutsy par ce que ce module est censé faire marcher le bouzin nativement mais il y arrive pas chez moi et "brouille" ndiswrappper.


La liberté ne s'use que si l'on ne s'en sert pas.

Hors ligne

#32 Le 19/12/2007, à 00:32

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

j'ai mis ta liste, mais quand je relance le tout, il ne parle que de eth0, faut-il changer interfaces ?

$ sudo /etc/init.d/networking restart
 * Reconfiguring network interfaces... Internet Systems Consortium DHCP Client V3.0.3
Copyright 2004-2005 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP

Listening on LPF/eth0/00:c0:9f:35:51:8e
Sending on   LPF/eth0/00:c0:9f:35:51:8e
Sending on   Socket/fallback
DHCPRELEASE on eth0 to 192.168.0.1 port 67
Internet Systems Consortium DHCP Client V3.0.3
Copyright 2004-2005 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP

Listening on LPF/eth0/00:c0:9f:35:51:8e
Sending on   LPF/eth0/00:c0:9f:35:51:8e
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPOFFER from 192.168.0.1
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.0.1
bound to 192.168.0.2 -- renewal in 42454 seconds.
                                                                         [ ok ]

Kubuntu Desktop 12.04  64 Bits

Hors ligne

#33 Le 19/12/2007, à 01:16

cflam69

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

Il a vraisemblablement un problème... sûrement et toujours un module à  trouver et bloquer.
Une fois que c'est fait, tout roule, tu verras.

Pour eth0, c'est pas forcément grave même si, en général, c'est wlan pour le wifi. Mais il arrive parfois (et rarement) que eth0 soit l'interface qui fonctionne. Toutefois, là  ce ne semble pas le cas manifestement tongue

Un dernier rappel :
REgarde en refaisans les manip' du wiki :
http://doc.ubuntu-fr.org/materiel/wifi/wg111v2

Bon, moi je prépare les valises ... si d'aventure tu es encore perdu dans une semaine,je serais là  pour t'aider.

Ciao


La liberté ne s'use que si l'on ne s'en sert pas.

Hors ligne

#34 Le 19/12/2007, à 01:19

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

bonnes vacances !


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#35 Le 23/12/2007, à 01:34

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

je vais passer sous gutsy... Et comme je viens de Dapper, je vais faire une réinstall complète. Mes données perso étant sur une autre partition, ça devrait se faire tranquillement, enfin si je ne me trompe pas lors de l'install roll

Capitain Flam, je te tiens au courant ! (Tu reviens dans notre galaxie le 26 ?)

Dernière modification par spip59 (Le 23/12/2007, à 01:36)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#36 Le 24/12/2007, à 16:13

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

me voilà  sous Gutsy Gibbon depuis peu. Sans rien exécuter, je vois maintenant mon réseau dans wifi radar en bas "connected to wificlub (avec IP pas du genre 168.192.*.*). les options disponibles sont "New, edit, delete, Disconnect", aucune ne sert, alors je me suis fait un dmesg pour en savoir :

$ dmesg
[  222.002228] usb 4-4: new high speed USB device using ehci_hcd and address 3
[  222.139130] usb 4-4: configuration #1 chosen from 1 choice
[  222.481450] ieee80211_init: failed to initialize WME (err=-17)
[  222.494501] iwlwifi_rc80211_simple: Unknown symbol iwlwifi_ieee80211_rate_control_unregister
[  222.494559] iwlwifi_rc80211_simple: Unknown symbol iwlwifi_sta_info_put
[  222.494605] iwlwifi_rc80211_simple: Unknown symbol iwlwifi_sta_info_get
[  222.494677] iwlwifi_rc80211_simple: Unknown symbol iwlwifi_ieee80211_rate_control_register
[  222.495947] wmaster0: Selected rate control algorithm 'simple'
[  222.595438] phy0: hwaddr 00:18:4d:bd:1e:97, rtl8187 V1 + rtl8225z2
[  222.595605] usbcore: registered new interface driver rtl8187
[  231.345046] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  361.142415] NET: Registered protocol family 17
[  433.952367] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  433.965801] eth0: Media Link Off

puis un peu plus loin, ça va un peu mieux, mais c'est pas encore ça

[  443.188385] wlan0: Initial auth_alg=0
[  443.188393] wlan0: authenticate with AP 00:1b:2f:72:3b:a8
[  443.189872] wlan0: RX authentication from 00:1b:2f:72:3b:a8 (alg=0 transaction=2 status=0)
[  443.189876] wlan0: authenticated
[  443.189879] wlan0: associate with AP 00:1b:2f:72:3b:a8
[  443.191984] wlan0: RX AssocResp from 00:1b:2f:72:3b:a8 (capab=0x461 status=0 aid=1)
[  443.191989] wlan0: associated
[  443.192405] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  446.174119] wlan0: No ProbeResp from current AP 00:1b:2f:72:3b:a8 - assume out of range
[  449.327429] wlan0: No STA entry for own AP 00:1b:2f:72:3b:a8
[  452.480761] wlan0: No STA entry for own AP 00:1b:2f:72:3b:a8

Je vais donc reprendre avec ndiswrapper


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#37 Le 26/12/2007, à 18:38

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

connexion toujours impossible sous gutsy.
ndiswrapper -l ne donne pas de résultat, mais l'interface graphique me dit que ça va (matériel + driver présents). Systeme > administration > reseau est différent de sous Dapper, je n'arrive pas à  désactiver la connexion sans fil. C'est soit itinérant, soit la config que je dois préciser, sinon je reste coincé dans la fenêtre.

j'ai revu que rtl8187 embêtait le monde, alors un coup de rmmod m'a permis de l'enlever pour un message plus sympatique. dmesg donne :

 
[10322.902930] usb 4-4: new high speed USB device using ehci_hcd and address 5
[10323.039913] usb 4-4: configuration #1 chosen from 1 choice
[10323.154401] usb 4-4: reset high speed USB device using ehci_hcd and address 5
[10323.306387] ndiswrapper: driver net111v2 (NETGEAR Inc.,03/27/2006,5.1213.06.0327) loaded
[10326.180234] wlan0: ethernet device 00:18:4d:bd:1e:97 using NDIS driver: net111v2, version: 0x1, NDIS version: 0x500, vendor: 'Realtek RTL8187 Wireless LAN USB NIC                                     ', 0846:6A00.F.conf
[10326.180278] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[10336.925497] wlan0: no IPv6 routers present
[10367.334725] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[10462.775861] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[10462.788123] eth0: Media Link Off
[10462.788543] ADDRCONF(NETDEV_UP): eth0: link is not ready
[10462.883534] eth0: Media Link Off

et ces dernières lignes s'affichent plusieurs fois, dues à  mes nombreuses tentatives infructueuses.

Alors je regarde à  nouveau les modules, aucun de ceux blacklisté ci-dessous n'apparaisse : r8187, islsmusb, islsm, islsm_usb, prism54usb, p54usb, p54common

Je suis vraiment perdu, car j'ai resuivi le tuto - sans ce qui était spécifique à  Breezy - et je me retrouve au même point. Sauf que je capte mon réseau quand le module rtl8187 est activé, sans pouvoir me connecter (je le vois à  l'adresse IP de wifi radar), et quand il est désactivé au profit de ndiswrapper, je ne capte plus qu'un réseau et des bizarrerie (voir ci-dessous). cflam69, pourrais-tu me rappeler les étapes essentiels, car j'en perds mon latin.

$ iwlist wlan0 scan
wlan0     Scan completed :
          Cell 01 - Address: 72:3B:5E:54:3D:C4
                    ESSID:"free"
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.412 GHz (Channel 1)
                    Quality:50/100  Signal level:-64 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
          Cell 02 - Address: 72:3B:5E:54:3D:C5
                    ESSID:""
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.412 GHz (Channel 1)
                    Quality:46/100  Signal level:-66 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK
          Cell 03 - Address: 72:3B:5E:54:3D:C6
                    ESSID:""
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.412 GHz (Channel 1)
                    Quality:48/100  Signal level:-65 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK
          Cell 04 - Address: 72:3B:5E:54:3D:C7
                    ESSID:""
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.412 GHz (Channel 1)
                    Quality:43/100  Signal level:-68 dBm  Noise level:-96 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK

Dernière modification par spip59 (Le 26/12/2007, à 18:39)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#38 Le 26/12/2007, à 19:18

cflam69

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

Slt,

Alors 2 choses :
- Sans utiliser ndiswrapper, et juste avec la reconnaissance du matériel par Gutsy, je voyais bien les réseaux alentours dont le mien ... sans pouvoir m'y connecter.
- Pour de connecter via ndiswrapper, il faut utiliser network-manager (avec moi ça marche), puis tu rentres tes paramètre de connexion (SSID, clef, ...)

ndiswrapper -l devrait te renvoyer quelquechoses. Peut-être avec sudo devant.
Sinon, on essayera une connexion à  la "mano" pour voir.

A+


La liberté ne s'use que si l'on ne s'en sert pas.

Hors ligne

#39 Le 26/12/2007, à 19:50

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

en effet...

$ sudo ndiswrapper -l
net111v2 : driver installed
        device (0846:6A00) present (alternate driver: rtl8187)

wifi radar 2 rsx sans le mien
networkmanager 8 réseaux dont 6 sans nom, toujours pas le mien

Y'a-t-il toujours le bug de breezy ? o๠on devait rajouter dans /etc/network/interfaces :

wireless-mode managed

ta blacklist, pourrais-tu me la donner ?

sudo gedit /etc/modprobe.d/blacklist

Dernière modification par spip59 (Le 26/12/2007, à 19:51)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#40 Le 27/12/2007, à 03:28

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

j'ai peut-être oublié de faire qqch. Je fais des essais demain, qui sait...


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#41 Le 27/12/2007, à 17:06

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

ça marche !
j'ai désactivé ndiswrapper, et j'ai repris à  partir de rtl8187 qui lui, détectait mon réseau.  J'avais toujours le même message d'erreur, malgré les sudo /etc/init.d/networking restart.

wlan0: No STA entry for own AP 00:1b:2f:72:3b:a8

J'ai redémarré, et ça a fonctionné, quelle a été ma surprise...  roll  En plus, cela fonctionne avec le cryptage WEP, waouh cool Mise à  part ça, il me reste à  désinstaller complétement ndiswrapper en suivant le tuto consacrer à ... ndiswrapper.  La lumière de la clé ne s'allume pas, mais c'est pas bien grave.

que d'efforts pour faire fonctionner tout ça... merci à  tous ceux qui m'ont aidé et fait progresser.


Kubuntu Desktop 12.04  64 Bits

Hors ligne

#42 Le 30/12/2007, à 01:46

vvf

Re : [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

j'ai découvert que, si l'envie me prenait de démarrer wifi radar, je perdais ma connexion.  dmesg me révélait ces messages d'erreur à  répétition :

wlan0: No STA entry for own AP 00:1b:2f:72:3b:a8

solution si la connexion a été perdue :
Il suffisait d'arrêter wifi-radar, de débrancher puis de rebrancher mon dongle, et là , je retrouvais ma connexion. Mes vaines tentatives décrites dans ce topic découlaient donc ce prgm qui empêchait le brave network-manager de faire son boulot. Comme quoi, il ne faut pas faire plusieurs choses en même temps ! @ bon entendeur !

Dernière modification par spip59 (Le 30/12/2007, à 01:47)


Kubuntu Desktop 12.04  64 Bits

Hors ligne

  • Accueil
  • » Forum
  • » WiFi
  • » [résolu] install clé wifi WG111v2 sur modem routeur netgear DG834Gv3

Haut de page ↑