Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 05/01/2008, à 10:09

cdomi

Décrochage connexion wifi

Bonjour

Depuis ma migration de ubuntu  de feisty à  Gutsy, de temps en temps ma connexion wifi décroche !

Je fais un test ping qui répond (Destination Host Unreachable)
puis redémarre "networking"pour que cela fonctionne.

C'est pas un gros pb mais il doit être possible de le régler.

Ma carte wifi pmcia ovyslink chipset ralink est reconnu normalement.

Je note que sur feisty ma carte était reconnu sur Ra0.
sous Gutsy wlan0....est-ce  un pb à  ce niveau ?

Merci

Domi

sudo /etc/init.d/networking restart
[sudo] password for domi:
* Reconfiguring network interfaces...
There is already a pid file /var/run/dhclient.eth0.pid with pid 5515
killed old client process, removed PID file
Internet Systems Consortium DHCP Client V3.0.5

wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/eth0/00:02:a5:ba:43:7d
Sending on   LPF/eth0/00:02:a5:ba:43:7d
Sending on   Socket/fallback
DHCPRELEASE on eth0 to 192.168.1.1 port 67
There is already a pid file /var/run/dhclient.wlan0.pid with pid 4000
killed old client process, removed PID file

wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/wlan0/00:08:a1:91:e8:1e
Sending on   LPF/wlan0/00:08:a1:91:e8:1e
Sending on   Socket/fallback
DHCPRELEASE on wlan0 to 192.168.1.1 port 67
ra0: ERROR while getting interface flags: No such device
Error for wireless request "Set Encode" (8B2A) :
   SET failed on device ra0 ; No such device.
Error for wireless request "Set ESSID" (8B1A) :
   SET failed on device ra0 ; No such device.
There is already a pid file /var/run/dhclient.ra0.pid with pid 134519120
Internet Systems Consortium DHCP Client V3.0.5

wmaster0: unknown hardware address type 801
SIOCSIFADDR: No such device
ra0: ERROR while getting interface flags: No such device
ra0: ERROR while getting interface flags: No such device
wmaster0: unknown hardware address type 801
Bind socket to interface: No such device
Failed to bring up ra0.
There is already a pid file /var/run/dhclient.wlan0.pid with pid 134519120
Internet Systems Consortium DHCP Client V3.0.5

wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/wlan0/00:08:a1:91:e8:1e
Sending on   LPF/wlan0/00:08:a1:91:e8:1e
Sending on   Socket/fallback
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
DHCPOFFER from 192.168.1.1
DHCPREQUEST on wlan0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.4 -- renewal in 42613 seconds.
There is already a pid file /var/run/dhclient.eth0.pid with pid 134519120
Internet Systems Consortium DHCP Client V3.0.5

wmaster0: unknown hardware address type 801
wmaster0: unknown hardware address type 801
Listening on LPF/eth0/00:02:a5:ba:43:7d
Sending on   LPF/eth0/00:02:a5:ba:43:7d
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 1
No DHCPOFFERS received.
No working leases in persistent database - sleeping.

Hors ligne

#2 Le 05/01/2008, à 10:41

nonobus

Re : Décrochage connexion wifi

Salut,

ra0 ou wlan0, je ne pense pas que ça soit le problème, c'est juste le nom de ton interface wifi.
En revanche, en regardant le retour de ta commande, il semble qu'il reste des traces de ton install sous feisty.

@pluche


"La censure épargne les corbeaux et s'acharne sur les colombes" Juvenal
"La tolérance est une vertu qui rend la paix possible" K.Annan
"Pourquoi Windows ? Parce que Linux ou l'inverse peut-être"

Hors ligne

#3 Le 05/01/2008, à 14:09

willy78

Re : Décrochage connexion wifi

donne ce retour:

lsmod | grep rt
sudo lshw -C network

Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum

Hors ligne

#4 Le 06/01/2008, à 18:14

cdomi

Re : Décrochage connexion wifi

willy78 a écrit :

donne ce retour:

lsmod | grep rt
sudo lshw -C network

Bonjour,

Voilà  les résultats

domi@malibu:~$ lsmod |grep rt
snd_rtctimer            3488  1 
rt2500pci              18176  0 
rt2x00pci              10624  1 rt2500pci
rt2x00lib              18688  2 rt2500pci,rt2x00pci
rfkill                  7184  1 rt2x00lib
mac80211              167816  4 rc80211_simple,rt2500pci,rt2x00pci,rt2x00lib
input_polldev           5000  1 rt2x00lib
crc_itu_t               2176  1 rt2x00lib
eeprom_93cx6            2304  1 rt2500pci
irtty_sir               8704  0 
sir_dev                16004  1 irtty_sir
parport_pc             36132  1 
parport                35656  3 ppdev,lp,parport_pc
irda                  192316  2 irtty_sir,sir_dev
rtc                    13208  1 snd_rtctimer
snd_timer              22916  3 snd_rtctimer,snd_pcm,snd_seq
iTCO_vendor_support     3972  1 iTCO_wdt
agpgart                33584  2 drm,intel_agp

Pour sudo lshw -C network :

*-network               
       description: RT2500
       vendor: Ralink Technology, Inc.
       physical id: 0
       version: 802.11  CardBus Reference Card
       slot: Socket 0
       resources: irq:11
  *-network
       description: Ethernet interface
       product: 82801CAM (ICH3) PRO/100 VM (KM) Ethernet Controller
       vendor: Intel Corporation
       physical id: 8
       bus info: pci@0000:02:08.0
       logical name: eth0
       version: 42
       serial: 00:02:a5:ba:43:7d
       size: 10MB/s
       capacity: 100MB/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.17-k4-NAPI duplex=half firmware=N/A latency=66 link=no maxlatency=56 mingnt=8 module=e100 multicast=yes port=MII speed=10MB/s
  *-network
       description: Wireless interface
       product: RT2500 802.11g Cardbus/mini-PCI
       vendor: RaLink
       physical id: 3
       bus info: pci@0000:03:00.0
       logical name: wmaster0
       version: 01
       serial: 00:08:a1:91:e8:1e
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list logical ethernet physical wireless
       configuration: broadcast=yes driver=rt2500pci ip=192.168.1.4 latency=64 module=rt2500pci multicast=yes wireless=IEEE 802.11g

Merci

Domi cool

Hors ligne

#5 Le 06/01/2008, à 20:33

willy78

Re : Décrochage connexion wifi

d'abord essayer les driver cvs et si ça marche pas on passera par ndiswrapper!:
Le driver natif de Gutsy s'appel rt2500pci et il fonctionne avec N-M même pour du WPA mais il cause pas mal de déconnexion!

Installation des driver de serialmonkey donc voila un mini tuto (connections par ethernet obligatoire):

sudo apt-get update
sudo apt-get install build-essential linux-headers-$(uname -r)
cd
mkdir rt2500
cd rt2500
wget http://rt2x00.serialmonkey.com/rt2500-cvs-daily.tar.gz
tar -zxvf rt2500-cvs-daily.tar.gz
cd rt2500-cvs*/Module
make

A ce stade le driver est compiler,
Maintenant il faut l'installer mais avant il faut décharger l'ancien (rt61pci)

sudo ifconfig wlan0 down
sudo modprobe -r rt2500pci
echo 'blacklist rt2500pci' | sudo tee -a /etc/modprobe.d/blacklist

On installe le driver fraichement compilé!

sudo make install
echo 'rt2500' | sudo tee -a /etc/modules

Il faut éditer le fichier pour donner les paramètres de connections

sudo gedit /etc/network/interfaces   #remplacer gedit par kwrite si tu es sous kubuntu

Placer ces lignes

en WEP hexa

auto wlan0
iface wlan0 inet dhcp
wireless-essid le_SSID_Du_rezo
wireless-key La_clé_en_hexa

en WPAPSK TKIP

auto wlan0
iface wlan0 inet dhcp
pre-up iwconfig wlan0 essid "mon ssid"
pre-up iwpriv wlan0 set AuthMode=WPAPSK
pre-up iwpriv wlan0 set EncrypType=TKIP
pre-up iwpriv wlan0 set WPAPSK="Ma_cle_WPA_Ultra_Secrete_que_y'a_que_moi_qui_sais"

rebooter et tester si la connexion est effective


Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum

Hors ligne

#6 Le 11/01/2008, à 15:09

Laskoni

Re : Décrochage connexion wifi

Bonjour,
j'ai le même problème depuis l'installation de Gutsy.
Ma carte n'est par contre pas la même, quel pilote dois-je utiliser?
Merci d'avance!

root@etxekoa:/home/nikolas# lsmod | grep rt
parport_pc             37412  0 
parport                37448  3 ppdev,parport_pc,lp
rt61pci                24576  0 
rt2x00pci              11520  1 rt61pci
rt2x00lib              19584  2 rt61pci,rt2x00pci
rfkill                  8208  1 rt2x00lib
mac80211              171016  4 rc80211_simple,rt61pci,rt2x00pci,rt2x00lib
input_polldev           5896  1 rt2x00lib
crc_itu_t               3072  1 rt2x00lib
eeprom_93cx6            3200  1 rt61pci
agpgart                35016  2 nvidia,intel_agp
root@etxekoa:/home/nikolas# sudo lshw -C network
  *-network               
       description: Ethernet interface
       product: L1 Gigabit Ethernet Adapter
       vendor: Attansic Technology Corp.
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: eth0
       version: b0
       serial: 00:1b:fc:81:38:e0
       size: 100MB/s
       capacity: 1GB/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.0.7 duplex=full firmware=N/A ip=192.168.0.12 latency=0 link=yes module=atl1 multicast=yes port=twisted pair speed=100MB/s
  *-network
       description: Wireless interface
       product: RT2561/RT61 rev B 802.11g
       vendor: RaLink
       physical id: 2
       bus info: pci@0000:05:02.0
       logical name: wmaster0
       version: 00
       serial: 00:19:5b:78:c2:0f
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list logical ethernet physical wireless
       configuration: broadcast=yes driver=rt61pci latency=64 module=rt61pci multicast=yes wireless=IEEE 802.11g

Hors ligne

#7 Le 11/01/2008, à 19:07

willy78

Re : Décrochage connexion wifi

Salut lasconi
tiens:

**********************************************************
Options A
Si tu n'as pas de connection

Télecharge ces fichiers sur le Bureau:
http://wlety.free.fr/rt61/rt61_rev_b_dlink.tar.gz
Paquets ndiswrapper
http://fr.archive.ubuntu.com/ubuntu/poo … u1_all.deb
http://fr.archive.ubuntu.com/ubuntu/poo … 1_i386.deb
Installation des paquets ndiswrapper:

cd ~/Desktop
cd ~/Bureau
sudo dpkg -i ndiswrapper-common_1.50-1ubuntu1_all.deb
sudo dpkg -i ndiswrapper-utils-1.9_1.50-1ubuntu1_i386.deb

puis:

tar -zxvf rt61_rev_b_dlink.tar.gz

*********************************************************

Options B
si tu as une connection

cd ~/Desktop
cd ~/Bureau
sudo apt-get install ndiswrapper-common ndiswrapper-utils-1.9
wget http://wlety.free.fr/rt61/rt61_rev_b_dlink.tar.gz
tar -zxvf rt61_rev_b_dlink.tar.gz

*********************************************************

Installation du driver windows par ndiswrapper

sudo ndiswrapper -i NetRt61.INF

donne le retour de cette commande pour vérifier si les driver sont bien chargé

ndiswrapper -l              #c'est un L minuscule

Ne pas continuer sans que quelqu'un ne t'es dit que c'était possible!

pour décharger le module charger automatiquement par Gutsy

sudo ifconfig wlan0 down
sudo rmmod rt61pci

Blacklister le module charger automatiquement par gutsy

echo 'blacklist rt61pci' | sudo tee -a /etc/modprobe.d/blacklist

pour charger ndiswrapper

sudo ndiswrapper -m
sudo modprobe ndiswrapper

Mettre ndiswrapper dans la liste des modules chargés au démarrage:

echo 'ndiswrapper' | sudo tee -a /etc/modules

Mettre le fichier a minima pour connection avec N-M (network-manager)

echo -e 'auto lo\niface lo inet loopback\n' | sudo tee /etc/network/interfaces

Tu peux maintenant te connecter avec N-M (2 tv en haut à  droite)

Dernière modification par willy78 (Le 11/01/2008, à 19:08)


Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum

Hors ligne

#8 Le 24/01/2008, à 19:42

Doogy

Re : Décrochage connexion wifi

Salut a tous, j'avais le même souci depuis ma migration avec une carte wifi utilisant les rt61 est bizarrement depuis que je me suis mis en mode itinérant plus de décrochage est

iwlist scan

me trouve davantage de réseau disponible.


Avant de conquerir le monde, met un pied devant l'autre!!!
(Nico)

Hors ligne