Contenu | Rechercher | Menus

Annonce

Si vous rencontrez des soucis à rester connecté sur le forum (ou si vous avez perdu votre mot de passe) déconnectez-vous et reconnectez-vous depuis cette page, en cochant la case "Me connecter automatiquement lors de mes prochaines visites".

#1 Le 19/12/2005, à 18:08

BlindeKinder

[résolute] Probleme de clavier apres installation de driver ATI

Salut :
Tout d'abord, je suis assez nouveau sur Ubuntu et sur Linux...
Je viens d'installer les drivers pour mon ATI Radeon 9600XT 256Mo...
d'abord le fglrx Ubuntu, puis celui d'ATI puis je sais plus trop tellement que j'en ai installe et desinstalle...
Maintenant ca va plus ou moins (2800 fps / 520 fps) excepte deux trois problemes de dual screen (si vous avez un truc pour avoir le VRAI dual screen, la je l'ai qu'en jumaux parfait)

Mais allons a l'essentiel: comme vous aurez remarque, je n'ai plus d'accents (quand je tape une lettre avec accent, ca donne ca " ") et plus de cedille (un beau 4 a la place) plus quelques problemes de touche comme la barre verticale... je precise qu'il s'agit d'un clavier suisse romand (suisse francais si vous preferez).
J'ai deja essaye de modifier xorg.conf dans tous les sens, mais sans succes.
http://forum.ubuntu-fr.org/viewtopic.php?pid=134158: peut etre une piste, mais pas de soluce pour moi...

Merci

Dernière modification par BlindeKinder (Le 26/12/2005, à 22:14)


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#2 Le 19/12/2005, à 18:25

sbrunner

Re : [résolute] Probleme de clavier apres installation de driver ATI

dans ton fichier /etc/X11/xorg.conf
tu doit evair une section qui ressemble à ça (français)

Section "InputDevice"
    Identifier    "Generic Keyboard"
    Driver        "keyboard"
    Option        "CoreKeyboard"
    Option        "XkbRules"    "xorg"
    Option        "XkbModel"    "pc105"
    Option        "XkbLayout"    "fr"
EndSection

pour les suisse comme moi :

Section "InputDevice"
    Identifier    "Generic Keyboard"
    Driver        "keyboard"
    Option        "CoreKeyboard"
    Option        "XkbRules"    "xorg"
    Option        "XkbModel"    "pc105"
    Option        "XkbLayout"    "ch"
    Option        "XkbOptions"    "fr"
EndSection

CU
Stéph

Hors ligne

#3 Le 19/12/2005, à 20:36

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

Bon, apres avoir essaye ca, puis seulement une partie de ca (seulement les parametres ch etc..), ca ne va toujours pas.
Au demarage de x, apres le chargement des modules, il part en mode console, et me dit que x n'a pas pu demarrer, erreur fatale ligne tel, qui correspond aux lignes changees.
Donc a chaque fois killall gdm, fglrxconfig puis retour sur gdm. Comme la config de fglrx ne m'a plus ecrase les changement dans xorg.conf, j'ai du finalement faire un dpkg-reconfigure xserver-xorg.

En attendant, voici une partie de xorg.conf (bien different d'avant):

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"ch"
	Option		"XkbVariant"	"fr"

mad

Dernière modification par BlindeKinder (Le 19/12/2005, à 20:40)


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#4 Le 19/12/2005, à 20:45

sbrunner

Re : [résolute] Probleme de clavier apres installation de driver ATI

Oups hmm en vérifiant chez moi j'ai vu que j'ai oublier l'option :

    Option "XkbVariant" "fr"

Hors ligne

#5 Le 19/12/2005, à 22:24

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

Bon, autre chose maintenant:
lorsque je tente de configurer le clavier par gnome

Erreur lors de l'activation de la configuration XKB.
Cela peut arriver pour plusieurs raisons :
- un bogue dans la bibliothèque libxklavier
- un bogue dans le serveur X (xkbcomp, utilitaires xmodmap)
- serveur X avec une implémentation de libxkbfile incompatible

Données de version du serveur X :
The X.Org Foundation
60802000

Si vous rapportez cette situation comme une anomalie, veuillez inclure :
- Le résultat de xprop -root | grep XKB
- Le résultat de gconftool-2 -R /desktop/gnome/peripherals/keyboard/kbd

les resultats dans l'ordre:

_XKB_RULES_NAMES_BACKUP(STRING) = "base", "pc101", "us", "", ""

et

 layouts = []
 model = microsoftinet
 overrideSettings = true
 options = []

Voila


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#6 Le 19/12/2005, à 23:10

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

J'ai encore reinstalle les fichiers mentiones dans le message d'erreur. Excepte le fait qu'il apparait maintenant apres le demarrage, toujours pas d'accent (etait il la peine de le mentionner: ptin, je passe vraiment pour un illetre mad )

Dernière modification par BlindeKinder (Le 19/12/2005, à 23:26)


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#7 Le 22/12/2005, à 15:58

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

sad personne ne peut donc m'aider?


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#8 Le 22/12/2005, à 20:43

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

J'ai du nouveau: j'ai remarque que tous les dossiers de /etc/X11/xkb sont vide ou contiennent des sous dossiers vides. Excepte /rules qui contient des fichiers de lien, comme xorg, mais il me dit que le lien est mort...

Donc?

Dernière modification par BlindeKinder (Le 22/12/2005, à 20:45)


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#9 Le 24/12/2005, à 17:54

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

big_smile:D:Dééééééééééééàààààèèèèèèèèèèèçççççççççççççççç@@@@@@@@@@@@@@@

on ne peut pas dire que vous m'avez été d'une aide très précieuse, à vrai dire je me sentais un peu seul ici...
Enfin ne soyons pas rencuniers, et donons la solution: 

# cd /etc/X11/
# mv xkb xkb.old
# apt-get install xkbutils --reinstall
# apt-get install xkeyboard-config --reinstall
# dpkg -i --force-confmiss /var/cache/apt/archives/xkeyboard-config_0.6-5breezy1_all.deb

C'est la soluce de quelqu'un qui avait trouvé quelqu'un qui avait trouvé... comme il s'agissait de la version unstable, j'ai adapté à breezy. Pour les lecteurs du futur, il faudra adapter la version de xkeyboard-config

Je ne sais pas dans quelle mesure il est important de réinstaller xkbutils et xkeyboard-config, quelqu'un pourrait me dire ça. C'est évidement la dernière ligne qui est importante, puisque elle force la réinstallation des fichiers de config, qui apparament ne s'installent pas avec un simple apt-get...

comme je vous ai dit, je suis nouveau sur linux, mais avec des bugs pareils, qu'est-ce qu'on apprend...
cool


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#10 Le 24/12/2005, à 17:57

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

au fait, comment on met "résolu" dans le titre?;)


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#11 Le 24/12/2005, à 22:59

sbrunner

Re : [résolute] Probleme de clavier apres installation de driver ATI

on édite le titre du premier message wink

Dernière modification par sbrunner (Le 24/12/2005, à 23:01)

Hors ligne

#12 Le 26/12/2005, à 22:16

BlindeKinder

Re : [résolute] Probleme de clavier apres installation de driver ATI

Fait! (ouf, ça fait du bien après deux semaines)
Merci Sbrunner:D


earth@universe:~$ sudo dpkg --force-remove-essential /usa/bill_gates.deb

Hors ligne

#13 Le 15/02/2006, à 08:36

Hazzgard

Re : [résolute] Probleme de clavier apres installation de driver ATI

Merci, car j'avais le même problème et j'ai pu le résoudre facilement. Par contre xkb me faisait des erreurs comme toi mais après la modification de xorg et relance de startx xkb fonctionnait impec.

Hors ligne

#14 Le 21/02/2006, à 14:33

Lapinbleu

Re : [résolute] Probleme de clavier apres installation de driver ATI

AIDEZ-MOI, SVP!!! wink

Il se trouve que j'ai eu EXACTEMENT le même probleme survenu apres la même chose. Seul certains accents me sont disponibles... mais pire... certains caracteres comme le at ne me sont pas accessibles!

Impossible de relever son mail sans "copier-coller" un "at" quelque part.

J'ai applique la solution qui consiste a regenerer les keymap... sans succes. A chaque fois que je veux installer un clavier (quelqu'il soit), il me met la boite de dialogue "Erreur lors de l'activation de la configuration XKB."

Je dispose moi aussi d'un clavier suisse romand...

Voici mon fichier xorg.conf pour infos:

# File: xorg.conf
# File generated by fglrxconfig (C) ATI Technologies, a substitute for xf86config.

# Note by ATI: the below copyright notice is there for servicing possibly
# pending third party rights on the file format and the instance of this file.
#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# **********************************************************************
# DRI Section
# **********************************************************************
Section "dri"
# Access to OpenGL ICD is allowed for all users:
    Mode 0666
# Access to OpenGL ICD is restricted to a specific user group:
#    Group 100    # users
#    Mode 0660
EndSection

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the Type1 and FreeType font modules
    Load        "type1"
    Load        "freetype"

# This loads the GLX module
    Load        "glx"   # libglx.a
    Load        "dri"   # libdri.a

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
# 

#    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
#    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
#    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
#    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client. 

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings. 

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier	"Keyboard1"
    Driver	"kbd"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option "Protocol"   "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
#    Option "Xleds"      "1 2 3"

#    Option "LeftAlt"    "Meta"
#    Option "RightAlt"   "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"   "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"   "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"  "de"
# or:
#    Option "XkbLayout"  "de"
#    Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
#    Option "XkbRules"   "xfree86"
#    Option "XkbModel"   "pc101"
#    Option "XkbLayout"  "us"
#    Option "XkbVariant" ""
#    Option "XkbOptions" ""

#    Option "XkbDisable"

    Option "XkbRules"	"xfree86"
    Option "XkbModel"	"pc105"
    Option "XkbLayout"	"fr_CH"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier	"Mouse1"
    Driver "mouse"
    Option "Protocol"   "ImPS/2"
    Option "ZAxisMapping"   "4 5"
    Option "Device"     "/dev/input/mice"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"   "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"   "9600"
#    Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"         "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"         "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"         "/dev/ttyS0"
#    Option     "MinX"           "1412"
#    Option     "MaxX"           "15184"
#    Option     "MinY"           "15372"
#    Option     "MaxY"           "1230"
#    Option     "ScreenNumber"   "0"
#    Option     "ReportingMode"  "Scaled"
#    Option     "ButtonNumber"   "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"         "/dev/ttyS0"
#    Option     "MinX"           "231"
#    Option     "MaxX"           "3868"
#    Option     "MinY"           "3858"
#    Option     "MaxY"           "272"
#    Option     "ScreenNumber"   "0"
#    Option     "ReportingMode"  "Scaled"
#    Option     "ButtonThreshold"    "17"
#    Option     "ButtonNumber"   "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"
    Identifier  "Monitor0"
# === mode lines based on GTF ===
# VGA @ 100Hz
# Modeline "640x480@100" 43.163 640 680 744 848 480 481 484 509 +hsync +vsync
# SVGA @ 100Hz
# Modeline "800x600@100" 68.179 800 848 936 1072 600 601 604 636 +hsync +vsync
# XVGA @ 100Hz
# Modeline "1024x768@100" 113.309 1024 1096 1208 1392 768 769 772 814 +hsync +vsync
# 1152x864 @ 60Hz
# Modeline "1152x864@60" 81.642 1152 1216 1336 1520 864 865 868 895 +hsync +vsync
# 1152x864 @ 85Hz
# Modeline "1152x864@85" 119.651 1152 1224 1352 1552 864 865 868 907 +hsync +vsync
# 1152x864 @ 100Hz
# Modeline "1152x864@100" 143.472 1152 1232 1360 1568 864 865 868 915 +hsync +vsync
# 1280x960 @ 75Hz
# Modeline "1280x960@75" 129.859 1280 1368 1504 1728 960 961 964 1002 +hsync +vsync
# 1280x960 @ 100Hz
# Modeline "1280x960@100" 178.992 1280 1376 1520 1760 960 961 964 1017  +hsync +vsync
# SXGA @ 100Hz
# Modeline "1280x1024@100" 190.960 1280 1376 1520 1760 1024 1025 1028 1085 +hsync +vsync
# SPEA GDM-1950 (60Hz,64kHz,110MHz,-,-): 1280x1024 @ V-freq: 60.00 Hz, H-freq: 63.73 KHz
# Modeline "GDM-1950"  109.62  1280 1336 1472 1720  1024 1024 1026 1062 -hsync -vsync
# 1600x1000 @ 60Hz
# Modeline "1600x1000" 133.142 1600 1704 1872 2144 1000 1001 1004 1035 +hsync +vsync
# 1600x1000 @ 75Hz
# Modeline "1600x1000" 169.128 1600 1704 1880 2160 1000 1001 1004 1044 +hsync +vsync
# 1600x1000 @ 85Hz
# Modeline "1600x1000" 194.202 1600 1712 1888 2176 1000 1001 1004 1050 +hsync +vsync
# 1600x1000 @ 100Hz
# Modeline "1600x1000" 232.133 1600 1720 1896 2192 1000 1001 1004 1059 +hsync +vsync
# 1600x1024 @ 60Hz
# Modeline "1600x1024" 136.385 1600 1704 1872 2144 1024 1027 1030 1060 +hsync +vsync
# 1600x1024 @ 75Hz
# Modeline "1600x1024" 174.416 1600 1712 1888 2176 1024 1025 1028 1069 +hsync +vsync
# 1600x1024 @ 76Hz
# Modeline "1600x1024" 170.450 1600 1632 1792 2096 1024 1027 1030 1070 +hsync +vsync
# 1600x1024 @ 85Hz
# Modeline "1600x1024" 198.832 1600 1712 1888 2176 1024 1027 1030 1075 +hsync +vsync
# 1920x1080 @ 60Hz
# Modeline "1920x1080" 172.798 1920 2040 2248 2576 1080 1081 1084 1118 -hsync -vsync
# 1920x1080 @ 75Hz
# Modeline "1920x1080" 211.436 1920 2056 2264 2608 1080 1081 1084 1126 +hsync +vsync
# 1920x1200 @ 60Hz
# Modeline "1920x1200" 193.156 1920 2048 2256 2592 1200 1201 1203 1242 +hsync +vsync
# 1920x1200 @ 75Hz
# Modeline "1920x1200" 246.590 1920 2064 2272 2624 1200 1201 1203 1253 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 2048x1536 @ 60
# Modeline "2048x1536" 266.952 2048 2200 2424 2800 1536 1537 1540 1589 +hsync +vsync
# 1400x1050 @ 60Hz M9 Laptop mode 
# ModeLine "1400x1050" 122.000 1400 1488 1640 1880 1050 1052 1064 1082 +hsync +vsync
# 1920x2400 @ 25Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@25" 124.620 1920 1928 1980 2048 2400 2401 2403 2434 +hsync +vsync
# 1920x2400 @ 30Hz for IBM T221, VS VP2290 and compatible display devices
# Modeline "1920x2400@30" 149.250 1920 1928 1982 2044 2400 2402 2404 2434 +hsync +vsync

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
    Identifier  "Standard VGA"
    VendorName  "Unknown"
    BoardName   "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset     "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver      "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# installed.

#    BusID       "PCI:0:10:0"

#    VideoRam    256

#    Clocks      25.2 28.3

EndSection

# === ATI device section ===

Section "Device"
    Identifier                          "ATI Graphics Adapter"
    Driver                              "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor  ===
    #Option                              "NoDDC"
# === disable/enable XAA/DRI ===
    Option "no_accel"                   "no"
    Option "no_dri"                     "no"
# === misc DRI settings ===
    Option "mtrr"                       "off" # disable DRI mtrr mapper, driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ###
# === Screen Management ===
    Option "DesktopSetup"               "(null)" 
    Option "ScreenOverlap"              "0" 
    Option "GammaCorrectionI"           "0x00000000"
    Option "GammaCorrectionII"          "0x00000000"
# === OpenGL specific profiles/settings ===
    Option "Capabilities"               "0x00000000"
    Option "CapabilitiesEx"             "0x00000000"
# === Video Overlay for the Xv extension ===
    Option "VideoOverlay"               "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
#       will be disabled automatically
    Option "OpenGLOverlay"              "off"
# === Center Mode (Laptops only) ===
    Option "CenterMode"                 "off"
# === Pseudo Color Visuals (8-bit visuals) ===
    Option "PseudoColorVisuals"         "off"
# === QBS Management ===
    Option "Stereo"                     "off"
    Option "StereoSyncEnable"           "1"
# === FSAA Management ===
    Option "FSAAEnable"                 "no"
    Option "FSAAScale"                  "1"
    Option "FSAADisableGamma"           "no"
    Option "FSAACustomizeMSPos"         "no"
    Option "FSAAMSPosX0"                "0.000000"
    Option "FSAAMSPosY0"                "0.000000"
    Option "FSAAMSPosX1"                "0.000000"
    Option "FSAAMSPosY1"                "0.000000"
    Option "FSAAMSPosX2"                "0.000000"
    Option "FSAAMSPosY2"                "0.000000"
    Option "FSAAMSPosX3"                "0.000000"
    Option "FSAAMSPosY3"                "0.000000"
    Option "FSAAMSPosX4"                "0.000000"
    Option "FSAAMSPosY4"                "0.000000"
    Option "FSAAMSPosX5"                "0.000000"
    Option "FSAAMSPosY5"                "0.000000"
# === Misc Options ===
    Option "UseFastTLS"                 "0"
    Option "BlockSignalsOnLock"         "on"
    Option "UseInternalAGPGART"         "yes"
    Option "ForceGenericCPU"            "no"
    BusID "PCI:1:0:0"    # vendor=1002, device=5b60
    Screen 0
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen0"
    Device      "ATI Graphics Adapter"
    Monitor     "Monitor0"
    DefaultDepth 24
    #Option "backingstore"

    Subsection "Display"
        Depth       24
        Modes       "1600x1200"
        ViewPort    0 0  # initial origin if mode is smaller than desktop
#        Virtual     1280 1024
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Server Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.

    Screen "Screen0"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

### EOF ###

D'avance merci a vous tous...

Hors ligne

#15 Le 21/02/2006, à 15:02

sbrunner

Re : [résolute] Probleme de clavier apres installation de driver ATI

Lapinbleu a écrit :

Il se trouve que j'ai eu EXACTEMENT le même probleme

Au hasard tu a EXACTEMENT la même solution (voir les 5 premiers pots) !

Hors ligne

#16 Le 21/02/2006, à 15:07

Lapinbleu

Re : [résolute] Probleme de clavier apres installation de driver ATI

La solution reside dans le xorg.conf ?

En fait, je n'ai pas bien compris ce qui prends le pas dans Gnome concernant la configuration du clavier...

Hors ligne

#17 Le 21/02/2006, à 15:35

sbrunner

Re : [résolute] Probleme de clavier apres installation de driver ATI

Oui effectivement, la configurations du clavier toit être comme ceci (pour le suisse) :

Section "InputDevice"
    Identifier    "Generic Keyboard"
    Driver        "keyboard"
    Option        "CoreKeyboard"
    Option        "XkbRules"     "xorg"
    Option        "XkbModel"     "pc105"
    Option        "XkbLayout"    "ch"
    Option        "XkbOptions"  "fr"
    Option        "XkbVariant"   "fr"
EndSection

la configuration contenamt la ligne suivante suivante ne marche pas :

    Option        "XkbLayout"    "fr_CH"

CU
Stéph

Hors ligne

#18 Le 21/02/2006, à 17:58

Lapinbleu

Re : [résolute] Probleme de clavier apres installation de driver ATI

En effet, mon clavier fonctionne désormais normlament. Il ne me reste plus qu'à supprimer le message d'erreur "Erreur lors de l'activation de la configuration XKB." lors du démarrage de la session.

Merci pour ton aide.

Hors ligne

Haut de page ↑