Ubuntu-fr

$@m

Installer une carte pci VT6421 : marche pas ! et probleme de udev

ben voilà... je ne sais pas si elle est installée ou non...

mais en tous les cas les disques sata comme ide ne sont pas reconnus

de plus, le ide n'apparait pas mais scsi2... !?

Enfin udev plantouille un peu... il me met une coup la carte via pci avec le nvidia interne... l'autre coup à l'inverse... c'est assez pénible...

Au passage :
- comment je peux réinitialiser juste la carte genre montage à chaud pour voir ce quelle détecte ?
- depuis la MàJ de udev (qui n'a rien changé aux permutations) il apparit des  "generic sg*" késako/interret ?

lspic :

RAID bus controller: VIA Technologies, Inc. VT6421 IDE RAID Controller (rev 50)

dmesg:

[   14.858469] SCSI subsystem initialized
[   14.863363] libata version 2.21 loaded.
[   14.920507] sata_via 0000:05:06.0: version 2.2
[   14.920954] sata_via 0000:05:06.0: routed to hard irq line 5
[   14.921090] scsi0 : sata_via
[   14.921166] scsi1 : sata_via
[   14.945519] scsi2 : sata_via
[   14.945618] ata1: SATA max UDMA/133 cmd 0x0000000000019000 ctl 0x000000000001900a mdma 0x000000000001a000 irq 16
[   14.945687] ata2: SATA max UDMA/133 cmd 0x0000000000019400 ctl 0x000000000001940a mdma 0x000000000001a008 irq 16
[   14.945756] ata3: PATA max UDMA/133 cmd 0x0000000000019800 ctl 0x000000000001980a mdma 0x000000000001a010 irq 16
[   15.261263] ata1: SATA link down (SStatus 0 SControl 310)
[   15.585026] ata2: SATA link down (SStatus 0 SControl 310)
[   15.769037] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   15.769089] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   15.769719] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
[   15.769779] NFORCE-CK804: chipset revision 242
[   15.769822] NFORCE-CK804: not 100% native mode: will probe irqs later
[   15.769871] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
[   15.769921]     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[   15.770028]     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[   15.770132] Probing IDE interface ide0...
[   16.060748] hda: TRANSCEND, CFA DISK drive
[   16.400506] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   16.401064] Probing IDE interface ide1...
[   16.972116] sata_nv 0000:00:07.0: version 3.4
[   16.972662] sata_nv 0000:00:07.0: Using ADMA mode
[   16.972908] scsi3 : sata_nv
[   16.973195] scsi4 : sata_nv
[   16.973413] ata4: SATA max UDMA/133 cmd 0xffffc20000aa8480 ctl 0xffffc20000aa84a0 bmdma x000000000001d800 irq 21
[   16.973483] ata5: SATA max UDMA/133 cmd 0xffffc20000aa8580 ctl 0xffffc20000aa85a0 bmdma x000000000001d808 irq 21
[   16.978478] hda: max request size: 128KiB
[   16.978526] hda: 8215200 sectors (4206 MB) w/0KiB Cache, CHS=8150/16/63, DMA
[   16.978682]  hda: hda1
[   17.135776] ReiserFS: hda1: found reiserfs format "3.6" with standard journal
[   17.135831] ReiserFS: hda1: using ordered data mode
...
[   17.443613] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   17.483799] ata4.00: ATA-7: ST3500641AS, 3.AAD, max UDMA/133
[   17.483848] ata4.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   17.558707] ata4.00: configured for UDMA/133
[   18.027101] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   18.065003] ata5.00: ATA-7: ST3500641AS, 3.AAD, max UDMA/133
[   18.065053] ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   18.139917] ata5.00: configured for UDMA/133
[   18.143241] scsi 3:0:0:0: Direct-Access     ATA      ST3500641AS      3.AA PQ: 0 ANSI: 5
[   18.143310] ata4: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[   18.147236] scsi 4:0:0:0: Direct-Access     ATA      ST3500641AS      3.AA PQ: 0 ANSI: 5
[   18.147302] ata5: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[   18.147803] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
[   18.147854] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 20
[   18.147959] sata_nv 0000:00:08.0: Using ADMA mode
[   18.148106] PCI: Setting latency timer of device 0000:00:08.0 to 64
[   18.148187] scsi5 : sata_nv
[   18.148284] scsi6 : sata_nv
[   18.148384] ata6: SATA max UDMA/133 cmd 0xffffc20000bfa480 ctl 0xffffc20000bfa4a0 bmdma 0x000000000001c400 irq 20
[   18.148453] ata7: SATA max UDMA/133 cmd 0xffffc20000bfa580 ctl 0xffffc20000bfa5a0 bmdma 0x000000000001c408 irq 20
[   18.618613] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   19.020202] ata6.00: ATA-7: Hitachi HDS725050KLA360, K2AKCD6A, max UDMA/133
[   19.020254] ata6.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   19.038807] ata6.00: configured for UDMA/133
[   19.509781] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   19.934939] ata7.00: ATA-7: Hitachi HDS725050KLA360, K2AKCD6A, max UDMA/133
[   19.934992] ata7.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   19.953976] ata7.00: configured for UDMA/133
[   19.954121] scsi 5:0:0:0: Direct-Access     ATA      Hitachi HDS72505 K2AK PQ: 0 ANSI: 5
[   19.954190] ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[   19.954335] scsi 6:0:0:0: Direct-Access     ATA      Hitachi HDS72505 K2AK PQ: 0 ANSI: 5
[   19.954400] ata7: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
...
[   24.594065] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[   24.594226] ide: failed opcode was: unknown
[   24.594361] hda: drive not ready for command
[   24.705298] hda: CHECK for good STATUS
[   24.705387] hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[   24.705514] hda: drive_cmd: error=0x04 { DriveStatusError }
[   24.705618] ide: failed opcode was: 0xef
[   24.705762] hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[   24.705888] hda: drive_cmd: error=0x04 { DriveStatusError }
[   24.705991] ide: failed opcode was: 0xef
[   24.706084] hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[   24.706210] hda: drive_cmd: error=0x04 { DriveStatusError }
[   24.706313] ide: failed opcode was: 0xe7
[   24.706428] hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[   24.706554] hda: drive_cmd: error=0x04 { DriveStatusError }
[   24.706657] ide: failed opcode was: 0xe7
...
[   25.874790] sd 3:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[   25.874850] sd 3:0:0:0: [sda] Write Protect is off
[   25.874894] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   25.874906] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   25.875017] sd 3:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[   25.875070] sd 3:0:0:0: [sda] Write Protect is off
[   25.875113] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   25.875124] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   25.875191]  sda:<6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   25.889821] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   25.971626]  sda1
[   25.971793] sd 3:0:0:0: [sda] Attached SCSI disk
[   25.971961] sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[   25.972016] sd 4:0:0:0: [sdb] Write Protect is off
[   25.972060] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   25.972072] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   25.972172] sd 4:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[   25.972225] sd 4:0:0:0: [sdb] Write Protect is off
[   25.972268] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   25.972280] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   25.972345]  sdb: sdb1
[   26.024954] sd 4:0:0:0: [sdb] Attached SCSI disk
[   26.064326] sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[   26.066077] sd 5:0:0:0: [sdc] Write Protect is off
[   26.066126] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[   26.092651] input: PC Speaker as /class/input/input2
[   26.093099] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.093222] sd 5:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[   26.093277] sd 5:0:0:0: [sdc] Write Protect is off
[   26.093321] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[   26.093332] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.093398]  sdc:<6>parport_pc 00:08: reported by Plug and Play ACPI
[   26.265892] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   26.298622]  sdc1
[   26.298790] sd 5:0:0:0: [sdc] Attached SCSI disk
[   26.299352] sd 6:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[   26.299923] sd 6:0:0:0: [sdd] Write Protect is off
[   26.299969] sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[   26.300415] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.300749] sd 6:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[   26.324103] sd 6:0:0:0: [sdd] Write Protect is off
[   26.324152] sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[   26.325195] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.325264]  sdd: sdd1
[   26.401000] sd 6:0:0:0: [sdd] Attached SCSI disk
...
[   26.471829] sd 3:0:0:0: Attached scsi generic sg0 type 0
[   26.471903] sd 4:0:0:0: Attached scsi generic sg1 type 0
[   26.471973] sd 5:0:0:0: Attached scsi generic sg2 type 0
[   26.472050] sd 6:0:0:0: Attached scsi generic sg3 type 0
...
[   33.750643] EXT3 FS on sdb1, internal journal
[   33.750647] EXT3-fs: mounted filesystem with ordered data mode.

Dernière modification par $@m (Le 07/03/2008, à 14:31)

$@m

Re : Installer une carte pci VT6421 : marche pas ! et probleme de udev

iop ?

$@m

Re : Installer une carte pci VT6421 : marche pas ! et probleme de udev

perosnne ?

keupson

Re : Installer une carte pci VT6421 : marche pas ! et probleme de udev

Même problème quelqu'un aurait une idée?