#1 Le 05/07/2014, à 17:45
- Loupus11
[Résolu]Données Smart de mon vieux serviteur
Bonjour A Tous,
Je ne suis pas pressé par le temps, mais si quelqu’un avait la gentillesse de jeter un coup d’œil sur les données smart de mon vieux disque, ça serait sympathique car, j’ai malheureusement l’impression que ce bon vieux serviteur, n’a plus que quelques mois à vivre. N’étant pas doué pour interpréter les données (808 heures ou 33 jours), Je préfère prendre les précautions nécessaires avant toutes interventions sur ce PC, qui pour l’instant a commis moins d’erreurs que celui qui se trouve derrière le clavier, je lui dois donc un minimum de respect.
Merci par avance, si par ailleurs une petite documentation sur l’interprétation des données smart était disponible en français, je suis preneur !
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.0-31-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-22ZCT0
Serial Number: WD-WXEY08TRH176
LU WWN Device Id: 5 0014ee 05660cb5d
Firmware Version: 11.01A11
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Sat Jul 5 14:58:33 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 122) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 186 185 021 Pre-fail Always - 1666
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1131
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1174
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1021
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 334
193 Load_Cycle_Count 0x0032 195 195 000 Old_age Always - 16268
194 Temperature_Celsius 0x0022 092 067 000 Old_age Always - 55
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 808 hours (33 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 bb 23 ed 40 Error: AMNF at LBA = 0x00ed23bb = 15541179
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 40 68 19 b8 b8 15 00 05:07:19.276 READ FPDMA QUEUED
60 20 60 c1 6f b5 15 00 05:07:19.276 READ FPDMA QUEUED
61 00 58 2f a6 c4 01 00 05:07:19.276 WRITE FPDMA QUEUED
61 00 50 2f a5 c4 01 00 05:07:19.276 WRITE FPDMA QUEUED
61 00 48 2f a4 c4 01 00 05:07:19.276 WRITE FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 808 hours (33 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 00 bb 23 ed 40 Error: AMNF at LBA = 0x00ed23bb = 15541179
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 50 9f 23 ed 1a 00 05:04:03.402 READ FPDMA QUEUED
61 20 48 bf 44 4f 03 00 05:04:03.401 WRITE FPDMA QUEUED
60 20 40 7f 23 ed 1a 00 05:04:03.401 READ FPDMA QUEUED
61 20 38 9f 44 4f 03 00 05:04:03.401 WRITE FPDMA QUEUED
60 20 30 5f 23 ed 1a 00 05:04:03.400 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
PS: C'est un pc portable Aspire 5920 ( ACER)
Dernière modification par Loupus11 (Le 07/07/2014, à 17:24)
Médion UK Akoya Ubuntu 14.04 LTS 64 bits
Intel(R) Pentium(R) CPU G630 @ 2.70GHz -4 Go Ram
intel: Driver for Intel Integrated Graphics Chipsets: i810,
La patience est un vêtement qui ne s'est jamais usé
Hors ligne
#2 Le 06/07/2014, à 15:14
- Zakhar
Re : [Résolu]Données Smart de mon vieux serviteur
Les compteurs ne montrent rien de grave.
Il y a eu deux erreurs historiquement mais allez savoir de quoi il s'agit...
Tu peux toujours lancer un smart test "long" pour vérifier que tout est OK.
"A computer is like air conditioning: it becomes useless when you open windows." (Linus Torvald)
Hors ligne
#3 Le 06/07/2014, à 15:52
- Loupus11
Re : [Résolu]Données Smart de mon vieux serviteur
@Zakhar,
Merci d'avoir répondu à cette demande c'est sympathique, cela me rassure, car ce PC me sert à faire des tests.
Ce type de portable a une fâcheuse tendance à la surchauffe, mal ventilé.
De plus il n'est pas très jeune, je vais donc tester dès que possible le Smart en version longue.
Si j'ai un réel doute sur le disque, je le posterai à nouveau ici.
Un grand Merci
Dernière modification par Loupus11 (Le 06/07/2014, à 15:57)
Médion UK Akoya Ubuntu 14.04 LTS 64 bits
Intel(R) Pentium(R) CPU G630 @ 2.70GHz -4 Go Ram
intel: Driver for Intel Integrated Graphics Chipsets: i810,
La patience est un vêtement qui ne s'est jamais usé
Hors ligne