#1 Le 20/11/2014, à 14:20
- c4nuser
[Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
Edit : le problème est plus large que le Wifi, c'est la carte mère qui est sérieusement endommagée, plus rien à en tirer.
Bonsoir,
Je viens faire appel à vos compétences cumulées pour un ordi récupéré auquel j'aimerais donner une seconde jeunesse.
Le Wifi ne fonctionnait pas sur le XP qui était installé, mais vu que je comptais pas le laisser sous XP, je m'en fichais un peu. Problème, ça ne marchait pas mieux depuis le live-CD et pas plus une fois Ubuntu 10.04 installé (j'ai ressorti une ancienne version pour ne pas avoir un système trop lourd vu l'âge de la machine).
Portable : Packard Bell EasyNote ALP Ajax GN
Ca fonctionne bien en ethernet, mais en Wifi, le refus est radical "no wireless extensions" en résultat à la commande iwconfig.
(je précise que le voyant Wifi s'allume normalement dès le démarrage
de la machine).
Donc si vous avez des idées de solution, je suis preneur avant de le renvoyer à la déchetterie à laquelle il était destiné !
Merci d'avance !
Bonne soirée,
cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=10.04
DISTRIB_CODENAME=lucid
DISTRIB_DESCRIPTION="Ubuntu 10.04.2 LTS"
lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:c062 Logitech, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID ffff:ffff
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS,
943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High
Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 3 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI
Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI
Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS
110M/GeForce Go 7300] (rev a1)
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection (rev 02)
06:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller
06:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter (rev 19)
06:01.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01)
06:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
06:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
lspci -nn | grep -i net
03:00.0 Network controller [0280]: Intel Corporation
PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
06:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
mael@mael-laptop:~$
lspci -k
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS,
943/940GML and 945GT Express Memory Controller Hub (rev 03)
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML
and 945GT Express PCI Express Root Port (rev 03)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High
Definition Audio Controller (rev 02)
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 1 (rev 02)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 2 (rev 02)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express
Port 3 (rev 02)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI
Controller #1 (rev 02)
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #2 (rev 02)
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #3 (rev 02)
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #4 (rev 02)
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI
Controller (rev 02)
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge (rev 02)
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 02)
Kernel driver in use: ata_piix
01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS
110M/GeForce Go 7300] (rev a1)
Kernel driver in use: nouveau
Kernel modules: nvidiafb, nouveau
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
[Golan] Network Connection (rev 02)
Kernel driver in use: iwl3945
Kernel modules: iwl3945
06:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394
06:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro
Host Adapter (rev 19)
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
06:01.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01)
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
06:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter (rev 0a)
06:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
sudo lshw -C network
*-network
description: Wireless interface
product: PRO/Wireless 3945ABG [Golan] Network Connection
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:03:00.0
logical name: wlan0
version: 02
serial: 00:13:02:9b:84:56
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet
physical wireless
configuration: broadcast=yes driver=iwl3945 latency=0
multicast=yes wireless=IEEE 802.11abg
resources: irq:28 memory:fe1ff000-fe1fffff
*-network
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 7
bus info: pci@0000:06:07.0
logical name: eth0
version: 10
serial: 00:18:f3:2e:29:dc
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii
10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too
driverversion=0.9.28 duplex=full ip=192.168.0.17 latency=64 link=yes
maxlatency=64 mingnt=32 multicast=yes port=MII speed=100MB/s
resources: irq:16 ioport:d800(size=256) memory:feafe400-feafe4ff
lsmod
Module Size Used by
binfmt_misc 6587 1
ppdev 5259 0
snd_hda_codec_si3054 3396 1
snd_hda_codec_analog 58598 1
snd_hda_intel 22005 5
snd_hda_codec 74201 3
snd_hda_codec_si3054,snd_hda_codec_analog,snd_hda_intel
fbcon 35102 71
tileblit 2031 1 fbcon
snd_hwdep 5412 1 snd_hda_codec
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
font 7557 1 fbcon
bitblit 4707 1 fbcon
snd_pcm 70694 6
snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
softcursor 1189 1 bitblit
vga16fb 11385 0
vgastate 8961 1 vga16fb
snd_seq_dummy 1338 0
snd_seq_oss 26722 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
arc4 1153 2
snd_seq_midi_event 6003 2 snd_seq_oss,snd_seq_midi
joydev 8740 0
snd_seq 47263 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 19098 2 snd_pcm,snd_seq
snd_seq_device 5700 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
nouveau 467048 2
snd 54180 21
snd_hda_codec_si3054,snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
ttm 49943 1 nouveau
iwl3945 68727 0
drm_kms_helper 29329 1 nouveau
soundcore 6620 1 snd
snd_page_alloc 7076 2 snd_hda_intel,snd_pcm
psmouse 63245 0
drm 162409 4 nouveau,ttm,drm_kms_helper
intel_agp 24375 0
i2c_algo_bit 5028 1 nouveau
sdhci_pci 5470 0
iwlcore 106050 1 iwl3945
asus_laptop 17008 0
mac80211 205402 2 iwl3945,iwlcore
usbhid 36110 0
agpgart 31724 3 ttm,drm,intel_agp
ricoh_mmc 2923 0
sdhci 15462 1 sdhci_pci
serio_raw 3978 0
led_class 2864 4 iwl3945,iwlcore,asus_laptop,sdhci
cfg80211 126528 3 iwl3945,iwlcore,mac80211
hid 67064 1 usbhid
lp 7028 0
video 17375 0
output 1871 1 video
lirc_atiusb 13388 0
lirc_dev 8884 1 lirc_atiusb
parport 32635 2 ppdev,lp
8139too 18545 0
ohci1394 26950 0
8139cp 16186 0
mii 4381 2 8139too,8139cp
ieee1394 81181 1 ohci1394
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
ifconfig
eth0 Link encap:Ethernet HWaddr 00:18:f3:2e:29:dc
inet adr:192.168.0.17 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::218:f3ff:fe2e:29dc/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:6610 erreurs:0 :0 overruns:0 frame:0
TX packets:5361 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:7096880 (7.0 MB) Octets transmis:607359 (607.3 KB)
Interruption:16 Adresse de base:0xd800
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:26 erreurs:0 :0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:2240 (2.2 KB) Octets transmis:2240 (2.2 KB)
wlan0 Link encap:Ethernet HWaddr 00:13:02:9b:84:56
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Interface doesn't support scanning : Input/output error
uname -r -m
2.6.32-28-generic i686
cat /etc/network/interfaces
auto lo
iface lo inet loopback
nm-tool
NetworkManager Tool
State: connected
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: iwl3945
State: disconnected
Default: no
HW Address: 00:13:02:9B:84:56
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
- Device: eth0 [Auto eth0] ----------------------------------------------------
Type: Wired
Driver: 8139too
State: connected
Default: yes
HW Address: 00:18:F3:2E:29:DC
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.0.17
Prefix: 24 (255.255.255.0)
Gateway: 192.168.0.254
DNS: 212.27.40.241
DNS: 212.27.40.240
sudo rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
Dernière modification par c4nuser (Le 14/12/2014, à 12:45)
Hors ligne
#2 Le 22/11/2014, à 00:51
- foustala
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
peux tu nous donner les réactions au chargement du driver svp
sudo rmmod iwl3945
sudo modprobe iwl3945
dmesg | tail -25
dmesg | grep iwl
attention la 10.04 en version desktop n'est plus supportée depuis mai 2013
Dernière modification par foustala (Le 22/11/2014, à 00:53)
Hors ligne
#3 Le 22/11/2014, à 21:25
- c4nuser
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
attention la 10.04 en version desktop n'est plus supportée depuis mai 2013
En fait, j'avais choisi cette version parce que je l'avais déja gravée dans mes archives CD, et que je n'avais plus de DVD-R sous la main (et suite à une expérience malheureuse en USB bootable, je n'ose plus essayer !).
Après avoir fait quelques achats de consommables, j'ai donc réinstallé à la place une version 14.04. Ce qui m'a résolu au passage les listes d'erreurs qui défilaient au démarrage, mais sans résoudre le souci initial de Wifi !
J'ai donc repris toutes les commandes listées dans mon message initial (pour ne pas vous faire jouer au jeu des 7 différences éventuelles !), et je ne vous remets que les 4 où il y a des différences (visiblement encore moins engageantes, puisque évoquant un wifi déconnecté) :
sudo lshw -C network
*-network DÉSACTIVÉ
description: Interface réseau sans fil
produit: PRO/Wireless 3945ABG [Golan] Network Connection
fabriquant: Intel Corporation
identifiant matériel: 0
information bus: pci@0000:03:00.0
nom logique: wlan0
version: 02
numéro de série: 00:13:02:9b:84:56
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwl3945 driverversion=3.13.0-32-generic firmware=15.32.2.9 latency=0 link=no multicast=yes wireless=IEEE 802.11abg
ressources: irq:44 mémoire:fe1ff000-fe1fffff
*-network
description: Ethernet interface
produit: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter
fabriquant: Realtek Semiconductor Co., Ltd.
identifiant matériel: 7
information bus: pci@0000:06:07.0
nom logique: eth0
version: 10
numéro de série: 00:18:f3:2e:29:dc
taille: 100Mbit/s
capacité: 100Mbit/s
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.0.17 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100Mbit/s
ressources: irq:16 portE/S:d800(taille=256) mémoire:feafe400-feafe4ff
Je ne comprends pas tout au détail des lignes, mais la première "network désactivé" ne m'inspire pas du positif !
(le voyant Wifi est toujours allumé, et aucun souci en ethernet).
ifconfig
(wlan0 a carrément disparu par rapport à la première version)
eth0 Link encap:Ethernet HWaddr 00:18:f3:2e:29:dc
inet adr:192.168.0.17 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::218:f3ff:fe2e:29dc/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:110406 erreurs:0 :0 overruns:0 frame:0
TX packets:59487 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:162324086 (162.3 MB) Octets transmis:4229423 (4.2 MB)
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:65536 Metric:1
Packets reçus:977 erreurs:0 :0 overruns:0 frame:0
TX packets:977 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:102251 (102.2 KB) Octets transmis:102251 (102.2 KB)
sudo iwlist scan
wlan0 Interface doesn't support scanning : Network is down
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
Ah oui, Network is down, carrément !
Je me demande si je préfère ça ou la version "wlan0 Interface doesn't support scanning : Input/output error" sous 10.04 !
nm-tools :
NetworkManager Tool
State: connected (global)
- Device: eth0 [Wired connection 1] -------------------------------------------
Type: Wired
Driver: 8139too
State: connected
Default: yes
HW Address: 00:18:F3:2E:29:DC
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.0.17
Prefix: 24 (255.255.255.0)
Gateway: 192.168.0.254
DNS: 212.27.40.241
DNS: 212.27.40.240
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: iwl3945
State: unavailable
Default: no
HW Address: 00:13:02:9B:84:56
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
Pour être exhaustif, Je vous remets lsmod, qui est globablement la même chose que dans la première version, mais dans le désordre.
lsmod
Module Size Used by
hid_generic 12492 0
usbhid 46997 0
hid 87604 2 hid_generic,usbhid
bnep 18895 2
rfcomm 53664 0
bluetooth 342206 10 bnep,rfcomm
snd_hda_codec_si3054 12864 1
snd_hda_codec_analog 14537 1
snd_hda_intel 42730 3
nouveau 969577 2
snd_hda_codec 164067 3 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec_analog
arc4 12536 2
snd_hwdep 13272 1 snd_hda_codec
mxm_wmi 12893 1 nouveau
snd_pcm 85501 3 snd_hda_codec_si3054,snd_hda_codec,snd_hda_intel
iwl3945 63619 0
wmi 18673 2 mxm_wmi,nouveau
snd_page_alloc 14230 2 snd_pcm,snd_hda_intel
iwlegacy 88016 1 iwl3945
snd_seq_midi 13132 0
r852 17722 0
ttm 72698 1 nouveau
sm_common 16772 1 r852
drm_kms_helper 47182 1 nouveau
snd_seq_midi_event 14475 1 snd_seq_midi
mac80211 546051 2 iwl3945,iwlegacy
nand 58760 2 r852,sm_common
snd_rawmidi 25135 1 snd_seq_midi
drm 244037 4 ttm,drm_kms_helper,nouveau
snd_seq 55383 2 snd_seq_midi_event,snd_seq_midi
nand_ecc 13136 1 nand
cfg80211 409394 3 iwl3945,iwlegacy,mac80211
snd_seq_device 14137 3 snd_seq,snd_rawmidi,snd_seq_midi
i2c_algo_bit 13197 1 nouveau
nand_bch 13067 1 nand
coretemp 13195 0
snd_timer 28584 2 snd_pcm,snd_seq
bch 17197 1 nand_bch
nand_ids 8547 1 nand
r592 17711 0
joydev 17101 0
mtd 52813 2 nand,sm_common
snd 60871 17 snd_hda_codec_si3054,snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_analog,snd_seq_midi
memstick 16174 1 r592
serio_raw 13230 0
soundcore 12600 1 snd
lpc_ich 16864 0
asus_laptop 23897 0
video 18903 1 nouveau
sparse_keymap 13708 1 asus_laptop
input_polldev 13648 1 asus_laptop
mac_hid 13037 0
parport_pc 31981 0
ppdev 17391 0
lp 13299 0
parport 40836 3 lp,ppdev,parport_pc
8139too 32571 0
psmouse 91329 0
8139cp 27171 0
mii 13654 2 8139cp,8139too
firewire_ohci 35529 0
firewire_core 61867 1 firewire_ohci
sdhci_pci 18535 0
crc_itu_t 12627 1 firewire_core
sdhci 37779 1 sdhci_pci
Du coup, je n'ai pas tenté le changement de driver proposé par Foustala. Non pas que je le mette en doute, mais à problème un peu différent, solution probablement un peu différente, et c'est surement plus simple pour vous de ne pas tenter trop de trucs simultanément.
(simplement, j'avais tenté le changement de driver suggéré, mais devant la liste à rallonge d'erreur retournée par les deux dernières commandes indiquées, j'ai directement éteint l'ordi, pour repartir d'une base 14.04.
Merci d'avance de votre aide !
Bonne soirée.
Dernière modification par c4nuser (Le 22/11/2014, à 21:29)
Hors ligne
#4 Le 23/11/2014, à 14:48
- foustala
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
je ne change pas le driver, je le recharge juste pour voir comment le système réagit.
donne nous le résultat svp
sudo rmmod -v iwl3945
sudo modprobe -v iwl3945
dmesg | tail -25
dmesg | grep iwl3945
sudo ifup -v wlan0
ifconfig -a
Dernière modification par foustala (Le 23/11/2014, à 14:52)
Hors ligne
#5 Le 23/11/2014, à 14:59
- foustala
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
ainsi que le paquet linux-firmware
sudo apt-get install --reinstall linux-firmware
Hors ligne
#6 Le 23/11/2014, à 19:10
- c4nuser
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
Salut, et merci de ton message !
Voilà la réponse aux commandes :
dmesg | tail -25
[ 293.489338] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 293.489357] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 293.489395] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 293.489403] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 293.489410] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 293.489643] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 293.489643]
[ 293.489667] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 293.489682] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 293.489702] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 293.489742] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 293.491503] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 293.491909] ieee80211 phy1: Hardware restart was requested
[ 293.569380] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 293.569390] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 293.569425] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 293.569429] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 293.569433] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 293.569661] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 293.569661]
[ 293.569683] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 293.569687] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 293.569697] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 293.571457] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 293.571773] ieee80211 phy1: Hardware restart was requested
dmesg | grep iwl3945
[ 411.664114] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 411.750576] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 411.750586] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 411.750620] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 411.750624] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 411.750627] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 411.750854] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 411.750872] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 411.750880] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 411.750887] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 411.752828] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 413.676115] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 413.753143] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 413.753163] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 413.753201] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 413.753209] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 413.753217] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 413.753449] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 413.753474] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 413.753489] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 413.753506] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 413.755294] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 413.755710] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 413.829580] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 413.829605] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 413.829642] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 413.829650] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 413.829658] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 413.829890] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 413.829922] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 413.829931] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 413.829939] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 413.831686] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 415.764048] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 415.841272] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 415.841281] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 415.841316] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 415.841320] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 415.841323] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 415.841551] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 415.841571] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 415.841582] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 415.841587] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 415.843329] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 417.776100] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 417.849704] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 417.849727] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 417.849765] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 417.849773] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 417.849781] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 417.850013] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 417.850039] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 417.850053] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 417.850073] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 417.850113] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 417.851875] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 417.929381] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 417.929405] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 417.929443] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 417.929462] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 417.929468] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 417.929698] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 417.929720] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 417.929731] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 417.929740] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 417.931504] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 419.864084] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 419.937349] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 419.937371] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 419.937409] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 419.937418] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 419.937434] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 419.937664] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 419.937682] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 419.937696] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 419.937713] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 419.937746] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 419.939493] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 420.017759] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 420.017785] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 420.017823] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 420.017831] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 420.017838] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 420.018071] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 420.018100] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 420.018109] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 420.018122] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 420.019900] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 421.952092] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 422.025791] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 422.025815] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 422.025853] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 422.025862] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 422.025869] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 422.026102] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 422.026134] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 422.026145] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 422.026157] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 422.027914] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 422.028239] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 422.105803] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 422.105828] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 422.105866] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 422.105874] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 422.105881] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 422.106114] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 422.106143] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 422.106152] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 422.106168] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 422.107944] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 424.040111] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 424.116815] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 424.116825] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 424.116861] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 424.116865] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 424.116869] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 424.117103] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 424.117117] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 424.117128] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 424.117133] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 424.118899] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 426.048109] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 426.125139] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 426.125160] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 426.125198] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 426.125206] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 426.125213] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 426.125446] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 426.125470] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 426.125487] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 426.125507] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 426.127294] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 426.127703] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 426.201529] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 426.201541] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 426.201579] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 426.201586] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 426.201591] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 426.201822] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 426.201846] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 426.201893] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 426.201900] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 426.203670] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 426.204393] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 426.281388] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 426.281413] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 426.281451] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 426.281459] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 426.281467] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 426.281699] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 426.281734] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 426.281741] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 426.281749] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 426.283495] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 428.216066] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 428.291303] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 428.291314] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 428.291349] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 428.291353] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 428.291357] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 428.291585] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 428.291607] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 428.291611] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 428.291619] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 428.293373] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 428.293780] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 428.373593] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 428.373602] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 428.373636] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 428.373641] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 428.373644] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 428.373871] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 428.373893] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 428.373903] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 428.373910] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 428.375665] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 430.304104] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 430.377351] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 430.377371] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 430.377408] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 430.377417] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 430.377424] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 430.377657] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 430.377681] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 430.377696] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 430.377712] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 430.377748] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 430.379507] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 430.457363] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 430.457386] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 430.457424] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 430.457432] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 430.457439] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 430.457672] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 430.457700] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 430.457712] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 430.457728] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 430.459505] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 432.392051] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 432.466781] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 432.466791] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 432.466825] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 432.466829] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 432.466833] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 432.467059] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 432.467091] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 432.467103] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 432.467111] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 432.468880] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 434.400049] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 434.486641] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 434.486652] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 434.486686] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 434.486690] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 434.486694] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 434.486920] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 434.486944] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 434.486963] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 434.486970] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 434.488891] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 436.412070] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 436.485300] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 436.485319] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 436.485357] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 436.485365] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 436.485373] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 436.485605] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 436.485630] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 436.485644] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 436.485661] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 436.485696] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 436.487455] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 436.565339] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 436.565362] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 436.565400] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 436.565419] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 436.565424] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 436.565654] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 436.565674] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 436.565685] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 436.565695] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 436.567456] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 438.500063] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 438.573259] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 438.573283] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 438.573321] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 438.573329] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 438.573336] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 438.573577] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 438.573592] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 438.573605] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 438.573620] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 438.573648] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 438.575393] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 438.653401] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 438.653424] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 438.653461] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 438.653470] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 438.653486] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 438.653716] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 438.653736] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 438.653748] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 438.653760] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 438.655521] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 440.588073] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 440.662293] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 440.662320] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 440.662358] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 440.662366] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 440.662373] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 440.662606] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 440.662635] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 440.662653] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 440.662666] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 440.662691] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 440.664428] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 440.741714] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 440.741739] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 440.741777] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 440.741785] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 440.741792] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 440.742033] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 440.742049] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 440.742061] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 440.742073] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 440.743846] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 440.744191] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 440.817607] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 440.817632] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 440.817669] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 440.817678] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 440.817685] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 440.817918] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 440.817946] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 440.817957] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 440.817972] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 440.819748] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 442.752112] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 442.829242] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 442.829266] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 442.829304] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 442.829312] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 442.829320] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 442.829552] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 442.829578] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 442.829593] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 442.829616] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 442.831411] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 442.831850] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 442.905378] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 442.905393] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 442.905428] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 442.905433] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 442.905436] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 442.905666] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 442.905703] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 442.905726] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 442.905731] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 442.907493] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 444.840055] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 444.917619] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 444.917628] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 444.917663] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 444.917667] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 444.917670] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 444.917898] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 444.917918] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 444.917929] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 444.917933] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 444.919675] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 446.852087] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
[ 446.925770] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 446.925795] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 446.925833] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 446.925841] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 446.925848] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 446.926081] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 446.926114] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 446.926125] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 446.926138] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 446.927896] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 446.928234] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 447.005702] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 447.005727] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 447.005770] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 447.005778] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 447.005785] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 447.006031] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 447.006063] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 447.006596] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 447.006607] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 447.008382] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 447.008843] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 447.086030] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 447.086054] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 447.086092] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 447.086100] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 447.086107] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 447.086348] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x0031C 0x00000 216
[ 447.086365] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 447.086376] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 447.086386] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 447.086413] iwl3945 0000:03:00.0: Try to add interface when device not ready
[ 447.088158] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 447.165356] iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
[ 447.165380] iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
[ 447.165418] iwl3945 0000:03:00.0: Start IWL Error Log Dump:
[ 447.165427] iwl3945 0000:03:00.0: Status: 0x000202E4, count: 1
[ 447.165434] iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line
[ 447.165674] iwl3945 0000:03:00.0: SYSASSERT (0x5) 0000006501 0x008B6 0x10A4E 0x00320 0x00000 216
[ 447.165692] iwl3945 0000:03:00.0: Error Reply type 0x000000FF cmd C_RXON (0x10) seq 0x0401 ser 0x00030000
[ 447.165706] iwl3945 0000:03:00.0: Command C_RXON failed: FW Error
[ 447.165721] iwl3945 0000:03:00.0: Error setting new configuration (-5).
[ 447.167488] iwl3945 0000:03:00.0: Can't stop Rx DMA.
[ 449.100065] iwl3945 0000:03:00.0: Wait for START_ALIVE timeout after 2000ms.
sudo ifup -v wlan0
Ignoring unknown interface wlan0=wlan0.
ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:18:f3:2e:29:dc
inet adr:192.168.0.17 Bcast:192.168.0.255 Masque:255.255.255.0
adr inet6: fe80::218:f3ff:fe2e:29dc/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:4472 erreurs:0 :0 overruns:0 frame:0
TX packets:3972 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:5302610 (5.3 MB) Octets transmis:385313 (385.3 KB)
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:65536 Metric:1
Packets reçus:371 erreurs:0 :0 overruns:0 frame:0
TX packets:371 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:35742 (35.7 KB) Octets transmis:35742 (35.7 KB)
wlan0 Link encap:Ethernet HWaddr 00:13:02:9b:84:56
BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
sudo apt-get install --reinstall linux-firmware
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état... Fait
0 mis à jour, 0 nouvellement installés, 1 réinstallés, 0 à enlever et 0 non mis à jour.
Il est nécessaire de prendre 0 o/20,7 Mo dans les archives.
Après cette opération, 0 o d'espace disque supplémentaires seront utilisés.
(Lecture de la base de données... 197560 fichiers et répertoires déjà installés.)
Préparation du décompactage de .../linux-firmware_1.127.8_all.deb ...
Décompactage de linux-firmware (1.127.8) sur (1.127.8) ...
Paramétrage de linux-firmware (1.127.8) ...
Et dans le menu réseau, j'ai maintenant "réseau Wifi / périphérique non prêt" en grisé.
Merci d'avance, et bonne soirée !
Hors ligne
#7 Le 23/11/2014, à 22:03
- foustala
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
Les logs du noyau sont bourrés d'erreurs
Essaie
sudo rmmod -f iwl3945
sudo modprobe iwl3945 disable_hw_scan=1
Hors ligne
#8 Le 24/11/2014, à 00:01
- c4nuser
Re : [Abandon : C.M. HS] Pas de Wifi sur portable Packard Bell Easy Note
Je pense effectivement que la machine a quelques autres problèmes plus graves.
C'est après-midi, j'ai du rebooter plusieurs fois pour lancer correctement la machine, qui restait bloquée au démarrage sur le logo constructeur.
Je n'ai pas trouvé de problème du coté du disque dur en analysant ses données SMART.
J'ai saisi tes deux commandes, mais elles sont passées sans rien renvoyer, et sans rien résoudre.
Je pense qu'il va falloir me faire une raison, il doit y avoir des problèmes sur la carte-mère.
Hors ligne