Contenu | Rechercher | Menus

Annonce

Si vous rencontrez des soucis à rester connecté sur le forum (ou si vous avez perdu votre mot de passe) déconnectez-vous et reconnectez-vous depuis cette page, en cochant la case "Me connecter automatiquement lors de mes prochaines visites".
Test de l'ISO d'Ubuntu francophone : nous avons besoin de testeurs pour la version francophone d'Ubuntu 14.04. Liens et informations ici.

#1 Le 30/06/2008, à 10:06

lamagie

install pilote Lan (P5Q Asus) [resolu]

bonjour, (je suis un vrai debutant)

je n'arrive pas avoir de connexion internet sous Ubuntu (Heron 8.04) par le biais de mon cable ethernet sur ma neufbox. le tout fonctionne pourtant sous XP. je ne vois pas les LED de mes ports s'allumer et j'en ai donc deduis que ma prise LAN n'etait pas activer sous Ubuntu.

Merci d'une aide

Dernière modification par lamagie (Le 17/07/2008, à 13:56)


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#2 Le 30/06/2008, à 10:11

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

Peux-tu ouvrir un terminal (applications -> accessoires) et donner le résultat des commandes

lspci
ifconfig

Hors ligne

#3 Le 30/06/2008, à 20:27

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

Hello
Desole, je n'avais plus acces a internet...

voici les resultats des commandes ci dessus

lspci:

00:00.0 Host bridge: Intel Corporation Eaglelake DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Eaglelake PCI Express Root Port (rev 02)
00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4
00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5
00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6
00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #2
00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller
00:1c.0 PCI bridge: Intel Corporation ICH10 PCI Express Port 1
00:1c.4 PCI bridge: Intel Corporation ICH10 PCI Express Port 5
00:1c.5 PCI bridge: Intel Corporation ICH10 PCI Express Port 6
00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1
00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2
00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3
00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #1
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller
00:1f.2 IDE interface: Intel Corporation ICH10 4 port SATA IDE Controller
00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller
00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE Controller
01:00.0 VGA compatible controller: nVidia Corporation GeForce 8800 GTS 512 (rev a2)
02:00.0 Ethernet controller: Attansic Technology Corp. Unknown device 1026 (rev b0)
03:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II Controller (rev b2)
05:03.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70)

et ifconfig:

lo        Link encap:Boucle locale   
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          Packets reçus:1846 erreurs:0 :0 overruns:0 frame:0
          TX packets:1846 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0 
          Octets reçus:94124 (91.9 KB) Octets transmis:94124 (91.9 KB)


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#4 Le 30/06/2008, à 20:57

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

Solution :

1) I installed ubuntu hardy, i has build-essential package installed (installer également les "headers" du noyau utilisé)
2) Then i downloaded the linux driver from: http://support.asus.com/download/download.aspx?product=1&SLanguage=us-en&type=map&model=P5KPL-CM
(as per my original post)
3) I then transfered the driver via usb stick to my laptop and unpacked the zip. (Actually i unpacked it on windows first as it has a .rar file that i could not unpack on linux Then i packed it up again on windows).
4) cd into <HOME_DIR>/LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src
5) then i ran: sudo KBUILD_NOPEDANTIC=1 make
6) then i ran: sudo KBUILD_NOPEDANTIC=1 make install
7) that worked and put a driver in /lib/modules/2.6.24-16-generic/kernel/drivers/net/atl1e/at1le.ko
8 ) i cd into that director and i run: sudo insmod ./atl1e.ko

julien69 a écrit :

En revanche il n'est pas expliqué comment charger le module au démarrage, en cherchant un peu -> il suffit de rajouter le nom du module (sans l'extension .ko) dans le fichier /etc/modules.conf (à ouvrir avec sudo)

Et enfin pour ceux qui comme moi n'avais pas leur carte réseau configurée, puisque non détecté à l'installation, il faut renseigner les fichiers /etc/network/interfaces et /etc/resolv.conf

Hors ligne

#5 Le 30/06/2008, à 23:34

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

honnetement je lutte la, j'essaye de faire ce qu tu me dis tout seul mais je bloque.
j'ai downloader le pilote que tu m'as indiqué directement sur mon DD en commun avec Ubuntu, du coup je sais pas trop comment faire ensuite.


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#6 Le 01/07/2008, à 22:20

citronbleu-v

Re : install pilote Lan (P5Q Asus) [resolu]

tu as la p5q normale ou la p5q pro ? car je compte m'acheter la p5q

Hors ligne

#7 Le 01/07/2008, à 22:26

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

1° Installer le paquet build-essential
2° Télécharger le pilote et le dézipper
3° Aller dans le répertoire "LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src" avec une console
4° Lancer "sudo KBUILD_NOPEDANTIC=1 make"
5° Lancer "sudo KBUILD_NOPEDANTIC=1 make install"
6° Aller dans /lib/modules/2.6.24-16-generic/kernel/drivers/net/atl1e/at1le.ko
7° Lancer "sudo insmod ./atl1e.ko"

Hors ligne

#8 Le 08/07/2008, à 16:51

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

bonjour,

Desolé de ne pas avoir repondu plus tot, j'ai été occupé a nettoyer le portable de ma chérie que j'avais moi meme vérolé big_smile, et bien en plus...(d'ailleurs a ce sujet je conseille le forum bibou0007.com ou j'ai trouvé une aide rapide et claire, des linuxiens si j'en crois le logo du forum).

Pour te repondre citronbleu, si il cela t'interresses toujours c'est une P5Q normale.

Et slasher, je suis en ce moment en train de réinstaller mon ubuntu, je vais tacher d'effectuer ta solution juste apres, merci pour ton aide.

Dernière modification par lamagie (Le 08/07/2008, à 16:52)


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#9 Le 08/07/2008, à 18:16

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

bon j'ai reussi a decompresser le driver sous windows, grace a 7-zip, le probleme maintenant c'est que la ligne de commande que tu me suggere ne fonctionne pas dans le terminal. ("LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src") alors comme je l'ai dit je suis mega debutant, il se peut donc que je fasse quelque chose à l'envers...

pour completer l'info, le message que m'affiche le terminal est:

bash: 2e-linux-v1.0.0.4/src: Aucun fichier ou dossier de ce type
bash: LinuxDrivers/L1e_Lan/ : est un repertoire
bash: 1e- : commande introuvable

Dernière modification par lamagie (Le 08/07/2008, à 19:22)


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#10 Le 08/07/2008, à 19:23

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

help


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#11 Le 08/07/2008, à 21:38

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

Tu tapes quoi exactement pour avoir ce message ?

Hors ligne

#12 Le 08/07/2008, à 22:46

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

je tape:"LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src", mais j'ai aussi essayé de changer de facon "logique" en inscrivant les racines ou se trouve mon dossier avec mon pilote a savoir:"/home/myusername/LinuxDrivers/L1e_Lan/|1e-|2e-linux-v1.0.0.4/src".
et du coup la reponse est:
bash: 2e-linux-v1.0.0.4/src: Aucun fichier ou dossier de ce type
bash: /home/bilou/LinuxDrivers/L1e_Lan/ : est un repertoire
bash: 1e- : commande introuvable

J'ai essayé quoi!!


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#13 Le 08/07/2008, à 22:48

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

cd /home/myusername/LinuxDrivers/L1e_Lan/|1e-|2e-linux-v1.0.0.4/src

smile (cd = change directory)

Hors ligne

#14 Le 08/07/2008, à 22:56

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

cool, tu es la.

Donc la je viens d'essayer la nouvelle ligne de commande que tu me suggeres est la reponse est:

cd /home/myusername/LinuxDrivers/L1e_Lan/: Aucun fichier ou dossier de ce type

1e- : commande introuvable

???


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#15 Le 08/07/2008, à 23:05

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

Ah oui nan y'a des caractères bizarres dans ta commande, c'est plutôt

cd /home/myusername/LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src

En changeant cette fois myusername par ton login... roll

Hors ligne

#16 Le 08/07/2008, à 23:14

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

nan, non plus... j'ai essayé entre deux ceci:

cd /home/myusername/LinuxDrivers/L1e_Lan/src/l1e-l2e-linux-v1.0.0.4

la reponse est par contre:

bash: 2e-linux-v1.0.0.4 : commande introuvable
bash: 1e- : commande introuvable

et aussi, etant donné qu'en lisant un readme j'ai vu qu'il s'agissait d'une version "ethernet adapter: 1.0.0.0", j'ai tenté:

cd /home/myusername/LinuxDrivers/L1e_Lan/src/l1e-l2e-linux-v1.0.0.0

mais c'est la meme reponse le .0 a la place du .4, c'est tout


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#17 Le 08/07/2008, à 23:22

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

je t'envoie le fichier readme, des fois que...

Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E Ethernet Adapter 
========================================================================== 
 
Contents A
======== 
 
- In This Release 
- Building and Installation 
- Command Line Parameters 
- Additional Configurations 
- Known Issues 
- Support 
 
In This Release 
=============== 
 
This file describes the Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E  
Ethernet Adapter, version 1.0.0.0 This driver supports the 2.4.x and 2.6.x kernels. 
 
This driver is only supported as a loadable module at this time. Atheros is not  
supplying patches against the kernel source to allow for static linking of  
the driver. For questions related to hardware requirements, refer to the  
documentation supplied with your Atheros(R) adapter. All hardware  
requirements listed apply to use with Linux. 
 
Building and Installation 
========================= 
 
To build a binary RPM* package of this driver, run 'rpmbuild -tb  
<filename.tar.gz>'. Replace <filename.tar.gz> with the specific filename of  
the driver. 
 
NOTE: For the build to work properly, the currently running kernel MUST match  
      the version and configuration of the installed kernel sources. If you  
      have just recompiled the kernel reboot the system now. 
 
      RPM functionality has only been tested in Red Hat distributions. 
 
1. Move the base driver tar file to the directory of your choice. For example, 
   use /home/username/arl1e or /usr/local/src/arl1e. 
 
2. Untar/unzip archive: 
 
     tar zxf arl1e-x.x.x.tar.gz 
 
3. Change to the driver src directory: 
 
     cd arl1e-x.x.x/src/ 
 
4. Compile the driver module: 
 
     make install 
 
   The binary will be installed as: 
 
     /lib/modules/<KERNEL VERSION>/kernel/drivers/net/arl1e.[k]o 
 
   The install locations listed above are the default locations. They might  
   not be correct for certain Linux distributions. For more information,  
   see the ldistrib.txt file included in the driver tar. 
 
5. Install the module: 
 
     insmod arl1e <parameter>=<value> 
 
6. Assign an IP address to the interface by entering the following, where 
   x is the interface number: 
 
     ifconfig ethx <IP_address> 
 
7. Verify that the interface works. Enter the following, where <IP_address> 
   is the IP address for another machine on the same subnet as the interface  
   that is being tested: 
 
     ping  <IP_address>  
 
Command Line Parameters 
======================= 
 
If the driver is built as a module, the  following optional parameters are  
used by entering them on the command line with the modprobe or insmod command 
using this syntax: 
 
     modprobe arl1e [<option>=<VAL1>,<VAL2>,...] 
 
     insmod arl1e [<option>=<VAL1>,<VAL2>,...]  
 
For example, with two L001 PCIE adapters, entering: 
 
     insmod arl1e TxMemSize=80,128 
loads the arl1e driver with 8KB TX memory for the first adapter and 10KB TX memory  
for the second adapter. 
 
The default value for each parameter is generally the recommended setting, 
unless otherwise noted. 
 
    NOTES: A descriptor describes a data buffer and attributes related to the  
           data buffer. This information is accessed by the hardware. 
 
MediaType 
Valid Range: 0-4 
	0    - auto-negotiate at all supported speeds 
	1    - only link at 100Mbps Full Duplex 
	2    - only link at 100Mbps Half Duplex 
	3    - only link at 10Mbps Full Duplex 
	4    - only link at 10Mbps Half Duplex 
Default Value: 0 
    MediaType forces the line speed/duplex to the specified value in  
    megabits per second(Mbps). If this parameter is not specified or is set  
    to 0 and the link partner is set to auto-negotiate, the board will  
    auto-detect the correct speed.  
 
IntModTimer 
Valid Range: 50-65000 
Default Value: 100 
    This value represents the minmum interval between interrupts controller  
    generated.  
 
RxMemBlock 
Valid Range: 16-512  
Default Value: 64 
    This value is the number of receice memory block allocated by the driver.  
    Increasing this value allows the driver to buffer more incoming packets.  
    Each memory block is 1536 bytes. 
 
    NOTE: Depending on the available system resources, the request for a 
    higher number of receive descriptors may be denied.  In this case, 
    use a lower number. 
 
TxMemSize 
Valid Range: 4-64 
Default Value: 8 
    This value is the number KB of transmit memory allocated by the driver.  
    Increasing this value allows the driver to queue more transmits. 
 
    NOTE: Depending on the available system resources, the request for a 
    higher number of transmit descriptors may be denied.  In this case, 
    use a lower number. 
 
FlashVendor 
Valid Range: 0-2 
Default Value: 0 
    This value standards on vendor of spi flash used by the adapter. 
    0 for Atmel, 1 for SST, 2 for ST 
     
 
Additional Configurations 
========================= 
 
  Configuring the Driver on Different Distributions 
  ------------------------------------------------- 
 
  Configuring a network driver to load properly when the system is started is 
  distribution dependent. Typically, the configuration process involves adding 
  an alias line to /etc/modules.conf as well as editing other system startup  
  scripts and/or configuration files. Many popular Linux distributions ship  
  with tools to make these changes for you. To learn the proper way to  
  configure a network device for your system, refer to your distribution  
  documentation. If during this process you are asked for the driver or module  
  name, the name for the Linux Base Driver for the Atheros AR8121/AR8113 is arl1e 
   
  As an example, if you install the arl1e driver for two AR8121/AR8113 adapters  
  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add the  
  following to modules.conf: 
 
       alias eth0 arl1e 
       alias eth1 arl1e 
       options arl1e Speed=10,100 Duplex=2,1 
 
  Viewing Link Messages 
  --------------------- 
 
  Link messages will not be displayed to the console if the distribution is  
  restricting system messages. In order to see network driver link messages  
  on your console, set dmesg to eight by entering the following: 
 
       dmesg -n 8 
 
  NOTE: This setting is not saved across reboots. 
 
 
Known Issues 
============ 
 
NOTE: For distribution-specific information, see the ldistrib.txt file  
      included in the driver tar. 
 
  Driver Compilation 
  ------------------ 
 
  When trying to compile the driver by running make install, the following 
  error may occur:  
 
      "Linux kernel source not configured - missing version.h" 
 
  To solve this issue, create the version.h file by going to the Linux source  
  tree and entering: 
 
      make include/linux/version.h. 
 Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E Ethernet Adapter 
========================================================================== 
 
Contents 
======== 
 
- In This Release 
- Building and Installation 
- Command Line Parameters 
- Additional Configurations 
- Known Issues 
- Support 
 
In This Release 
=============== 
 
This file describes the Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E  
Ethernet Adapter, version 1.0.0.0 This driver supports the 2.4.x and 2.6.x kernels. 
 
This driver is only supported as a loadable module at this time. Atheros is not  
supplying patches against the kernel source to allow for static linking of  
the driver. For questions related to hardware requirements, refer to the  
documentation supplied with your Atheros(R) adapter. All hardware  
requirements listed apply to use with Linux. 
 
Building and Installation 
========================= 
 
To build a binary RPM* package of this driver, run 'rpmbuild -tb  
<filename.tar.gz>'. Replace <filename.tar.gz> with the specific filename of  
the driver. 
 
NOTE: For the build to work properly, the currently running kernel MUST match  
      the version and configuration of the installed kernel sources. If you  
      have just recompiled the kernel reboot the system now. 
 
      RPM functionality has only been tested in Red Hat distributions. 
 
1. Move the base driver tar file to the directory of your choice. For example, 
   use /home/username/arl1e or /usr/local/src/arl1e. 
 
2. Untar/unzip archive: 
 
     tar zxf arl1e-x.x.x.tar.gz 
 
3. Change to the driver src directory: 
 
     cd arl1e-x.x.x/src/ 
 
4. Compile the driver module: 
 
     make install 
 
   The binary will be installed as: 
 
     /lib/modules/<KERNEL VERSION>/kernel/drivers/net/arl1e.[k]o 
 
   The install locations listed above are the default locations. They might  
   not be correct for certain Linux distributions. For more information,  
   see the ldistrib.txt file included in the driver tar. 
 
5. Install the module: 
 
     insmod arl1e <parameter>=<value> 
 
6. Assign an IP address to the interface by entering the following, where 
   x is the interface number: 
 
     ifconfig ethx <IP_address> 
 
7. Verify that the interface works. Enter the following, where <IP_address> 
   is the IP address for another machine on the same subnet as the interface  
   that is being tested: 
 
     ping  <IP_address>  
 
Command Line Parameters 
======================= 
 
If the driver is built as a module, the  following optional parameters are  
used by entering them on the command line with the modprobe or insmod command 
using this syntax: 
 
     modprobe arl1e [<option>=<VAL1>,<VAL2>,...] 
 
     insmod arl1e [<option>=<VAL1>,<VAL2>,...]  
 
For example, with two L001 PCIE adapters, entering: 
 
     insmod arl1e TxMemSize=80,128 
loads the arl1e driver with 8KB TX memory for the first adapter and 10KB TX memory  
for the second adapter. 
 
The default value for each parameter is generally the recommended setting, 
unless otherwise noted. 
 
    NOTES: A descriptor describes a data buffer and attributes related to the  
           data buffer. This information is accessed by the hardware. 
 
MediaType 
Valid Range: 0-4 
	0    - auto-negotiate at all supported speeds 
	1    - only link at 100Mbps Full Duplex 
	2    - only link at 100Mbps Half Duplex 
	3    - only link at 10Mbps Full Duplex 
	4    - only link at 10Mbps Half Duplex 
Default Value: 0 
    MediaType forces the line speed/duplex to the specified value in  
    megabits per second(Mbps). If this parameter is not specified or is set  
    to 0 and the link partner is set to auto-negotiate, the board will  
    auto-detect the correct speed.  
 
IntModTimer 
Valid Range: 50-65000 
Default Value: 100 
    This value represents the minmum interval between interrupts controller  
    generated.  
 
RxMemBlock 
Valid Range: 16-512  
Default Value: 64 
    This value is the number of receice memory block allocated by the driver.  
    Increasing this value allows the driver to buffer more incoming packets.  
    Each memory block is 1536 bytes. 
 
    NOTE: Depending on the available system resources, the request for a 
    higher number of receive descriptors may be denied.  In this case, 
    use a lower number. 
 
TxMemSize 
Valid Range: 4-64 
Default Value: 8 
    This value is the number KB of transmit memory allocated by the driver.  
    Increasing this value allows the driver to queue more transmits. 
 
    NOTE: Depending on the available system resources, the request for a 
    higher number of transmit descriptors may be denied.  In this case, 
    use a lower number. 
 
FlashVendor 
Valid Range: 0-2 
Default Value: 0 
    This value standards on vendor of spi flash used by the adapter. 
    0 for Atmel, 1 for SST, 2 for ST 
     
 
Additional Configurations 
========================= 
 
  Configuring the Driver on Different Distributions 
  ------------------------------------------------- 
 
  Configuring a network driver to load properly when the system is started is 
  distribution dependent. Typically, the configuration process involves adding 
  an alias line to /etc/modules.conf as well as editing other system startup  
  scripts and/or configuration files. Many popular Linux distributions ship  
  with tools to make these changes for you. To learn the proper way to  
  configure a network device for your system, refer to your distribution  
  documentation. If during this process you are asked for the driver or module  
  name, the name for the Linux Base Driver for the Atheros AR8121/AR8113 is arl1e 
   
  As an example, if you install the arl1e driver for two AR8121/AR8113 adapters  
  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add the  
  following to modules.conf: 
 
       alias eth0 arl1e 
       alias eth1 arl1e 
       options arl1e Speed=10,100 Duplex=2,1 
 
  Viewing Link Messages 
  --------------------- 
 
  Link messages will not be displayed to the console if the distribution is  
  restricting system messages. In order to see network driver link messages  
  on your console, set dmesg to eight by entering the following: 
 
       dmesg -n 8 
 
  NOTE: This setting is not saved across reboots. 
 
 
Known Issues 
============ 
 
NOTE: For distribution-specific information, see the ldistrib.txt file  
      included in the driver tar. 
 
  Driver Compilation 
  ------------------ 
 
  When trying to compile the driver by running make install, the following 
  error may occur:  
 
      "Linux kernel source not configured - missing version.h" 
 
  To solve this issue, create the version.h file by going to the Linux source  
  tree and entering: 
 
      make include/linux/version.h. 
 
 
Support 
======= 
 
For general information, go to the Atheros support website at: 
 
    http://support.atheros.com 
 
If an issue is identified with the released source code on the supported 
kernel with a supported adapter, email the specific information related to  
the issue to xiong.huang@atheros.com 
 
License 
======= 
 
This software program is released under the terms of a license agreement  
between you ('Licensee') and Atheros. Do not use or load this software or any  
associated materials (collectively, the 'Software') until you have carefully  
read the full terms and conditions of the LICENSE located in this software  
package. By loading or using the Software, you agree to the terms of this  
Agreement. If you do not agree with the terms of this Agreement, do not  
install or use the Software. 
 
* Other names and brands may be claimed as the property of others.

Dernière modification par slasher-fun (Le 08/07/2008, à 23:26)


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#18 Le 08/07/2008, à 23:26

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

C'est pas des |, c'est des l !

Hors ligne

#19 Le 08/07/2008, à 23:29

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

c'est pas alt 6???


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#20 Le 08/07/2008, à 23:29

slasher_fun

Re : install pilote Lan (P5Q Asus) [resolu]

nan, des L minuscules...

Hors ligne

#21 Le 08/07/2008, à 23:38

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

aaaaaaah,

bon ok, j'ai esaye et il ne me parle plus de commande introuvable mais pour toutes les solutions proposé il continue par contre de me dire: "aucun fichier ou dossier de ce type"


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#22 Le 09/07/2008, à 00:05

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

bon, je vais o dodo, j'en peux plus merci pour ton aide en tout cas si tu as un peu de temps pour telecharger toi meme le pilote et voir si ce que l'on a fait colle avec les fichiers se serait cool, mon anglais est tres moyen et mon linux, n'en parlons pas.

quoiqu il en soit merci


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#23 Le 09/07/2008, à 19:07

lamagie

Re : install pilote Lan (P5Q Asus) [resolu]

Bon, j'ai tout simplement été racheté une carte reseau PCI, j'avoue qu'au bout de deux semaines a pas avancer ca me galerer et du coup pour 10E, j'ai eu droit a la detection automatique. smile

Merci d'avoir essaye mais je vais tacher d'apprendre les choses dans l'ordre a partir de maintenant. (je vais pouvoir continuer ma lecture de "simple comme ubuntu")

A+


Nouveau sous Linux (Ubuntu Hardy Heron 8.04)

Hors ligne

#24 Le 15/07/2008, à 22:22

mikubuntu

Re : install pilote Lan (P5Q Asus) [resolu]

slasher-fun a écrit :

Solution :

1) I installed ubuntu hardy, i has build-essential package installed
2) Then i downloaded the linux driver from: http://support.asus.com/download/download.aspx?product=1&SLanguage=us-en&type=map&model=P5KPL-CM
(as per my original post)
3) I then transfered the driver via usb stick to my laptop and unpacked the zip. (Actually i unpacked it on windows first as it has a .rar file that i could not unpack on linux Then i packed it up again on windows).
4) cd into <HOME_DIR>/LinuxDrivers/L1e_Lan/l1e-l2e-linux-v1.0.0.4/src
5) then i ran: sudo KBUILD_NOPEDANTIC=1 make
6) then i ran: sudo KBUILD_NOPEDANTIC=1 make install
7) that worked and put a driver in /lib/modules/2.6.24-16-generic/kernel/drivers/net/atl1e/at1le.ko
8 ) i cd into that director and i run: sudo insmod ./atl1e.ko

Merci, cela fonctionne parfaitement.

note: le "build-essential" est dans le cd d'installation d'ubuntu mais n'est pas installé par défault.

Hors ligne

#25 Le 16/07/2008, à 01:32

citronbleu-v

Re : install pilote Lan (P5Q Asus) [resolu]

je confirme, ça fonctionne smile merci pour l'information

Hors ligne

Haut de page ↑