Pages : 1
#1 Le 14/03/2015, à 23:12
- shargar
comment contourner l'interupteur wifi clavier on/off
Salut !
Je souhaite remettre en route un vieux easynote (packard bell). J'ai installé 14.04 nickel. Je galère pour le wifi. Network manager m'explique que le wifi est désactivé par un comutateur matériel.
D'après mes touches clavier, une combinaison Fn + F1 devrait mettre en route le wifi ; mais les commandes Fn + une touches semblent répondre de façon anarchique sur ce pc ! Ca marche mal pour le son, bien pour la luminosité et ça plante pour l'affichage grand ecran... La commande wifi fn+F1 semble parfaitement inactive...
comment déclencher cet interupteur autrement?
Dernière modification par shargar (Le 14/03/2015, à 23:17)
Hors ligne
#2 Le 15/03/2015, à 10:33
- toutafai
Re : comment contourner l'interupteur wifi clavier on/off
Bonjour,
Plusieurs méthodes :
- le classique mais qui ne fonctionne pas a tous les coups :
sudo rfkill unblock all
- Dans le bios, si l'option y a été implémentée : on trouve parfois une option permettant de dire au pc de toujours activé la carte wifi
- par des fichiers de configuration de module ou en "blacklistant" un module : la, je donne pas d'exemple car cela dépends de ta configuration matérielle et donc des modules qui sont chargés
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#3 Le 15/03/2015, à 18:23
- shargar
Re : comment contourner l'interupteur wifi clavier on/off
Bonjour Toutafai ;
- le sudo rfkill unblock all ne donne rien ( j'avais trouvé la commande dans un de tes post sur le forum ).
- j'ai parcouru le bios sans rien remarqué de spécial qui se rapporterai au wifi. Dans "Advanced" MC97controller, AC97 Controller et Ethernet controller sont tous "Enable"
- si t'es ok pour m'aider je tenterai bien ta troisième proposition. J'ai pas une grosse maîtrise de l'informatique. Peux tu m'en dire plus ?
Hors ligne
#4 Le 15/03/2015, à 18:53
- toutafai
Re : comment contourner l'interupteur wifi clavier on/off
ok, sans pb pour le 3, mais il faut des infos technique, donc fait ce qui est demandé dans "Script : Récolte des info de a lire avant de poster !!"; on en reparle une fois que ce sera fait
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#5 Le 15/03/2015, à 22:16
- shargar
Re : comment contourner l'interupteur wifi clavier on/off
Alors c'est parti !
cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=14.04
DISTRIB_CODENAME=trusty
DISTRIB_DESCRIPTION="Ubuntu 14.04.2 LTS"
lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
lspci
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:01.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 8b)
01:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
lspci -nn | grep -i net
01:01.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
01:02.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] [1106:3106] (rev 8b)
lspci -k
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: agpgart-intel
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Packard Bell B.V. Device d004
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Packard Bell B.V. Device d004
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: i915
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
Subsystem: Packard Bell B.V. Device d004
00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
Kernel driver in use: lpc_ich
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
Subsystem: Packard Bell B.V. Device d004
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: snd_intel8x0
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
Subsystem: Packard Bell B.V. Device d004
01:01.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
Subsystem: Intel Corporation WM3B2300BG Mini-PCI Card
Kernel driver in use: ipw2200
01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 8b)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: via-rhine
01:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
Subsystem: Packard Bell B.V. Device d004
Kernel driver in use: yenta_cardbus
sudo lshw -C network
*-network:0 DÉSACTIVÉ
description: Interface réseau sans fil
produit: PRO/Wireless 2200BG [Calexico2] Network Connection
fabriquant: Intel Corporation
identifiant matériel: 1
information bus: pci@0000:01:01.0
nom logique: eth1
version: 05
numéro de série: 00:0e:35:b4:83:24
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ipw2200 driverversion=1.2.2kmprq firmware=ABG:9.0.5.27 (Dec 12 2007) latency=64 link=no maxlatency=24 mingnt=3 multicast=yes wireless=IEEE 802.11bg
ressources: irq:11 mémoire:e0001000-e0001fff
*-network:1
description: Ethernet interface
produit: VT6105/VT6106S [Rhine-III]
fabriquant: VIA Technologies, Inc.
identifiant matériel: 2
information bus: pci@0000:01:02.0
nom logique: eth0
version: 8b
numéro de série: 00:40:d0:67:41:19
taille: 100Mbit/s
capacité: 100Mbit/s
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.1 duplex=full ip=192.168.1.13 latency=64 link=yes maxlatency=8 mingnt=3 multicast=yes port=MII speed=100Mbit/s
ressources: irq:3 portE/S:c000(taille=256) mémoire:e0000000-e00000ff
lsmod
Module Size Used by
bnep 18895 2
rfcomm 53664 0
bluetooth 342208 10 bnep,rfcomm
snd_intel8x0 33110 2
snd_ac97_codec 105709 1 snd_intel8x0
ac97_bus 12642 1 snd_ac97_codec
snd_pcm 85501 2 snd_ac97_codec,snd_intel8x0
snd_page_alloc 14230 2 snd_intel8x0,snd_pcm
snd_seq_midi 13132 0
snd_seq_midi_event 14475 1 snd_seq_midi
snd_rawmidi 25135 1 snd_seq_midi
pcmcia 51828 0
ipw2200 136401 0
snd_seq 55383 2 snd_seq_midi_event,snd_seq_midi
libipw 33144 1 ipw2200
snd_seq_device 14137 3 snd_seq,snd_rawmidi,snd_seq_midi
joydev 17101 0
i915 710013 2
snd_timer 28584 2 snd_pcm,snd_seq
lib80211 14040 2 libipw,ipw2200
yenta_socket 40201 0
drm_kms_helper 48868 1 i915
snd 60939 12 snd_ac97_codec,snd_intel8x0,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_seq_device,snd_seq_midi
lpc_ich 16864 0
cfg80211 409394 2 libipw,ipw2200
serio_raw 13230 0
pcmcia_rsrc 18319 1 yenta_socket
drm 244037 3 i915,drm_kms_helper
soundcore 12600 1 snd
pcmcia_core 22328 3 pcmcia,pcmcia_rsrc,yenta_socket
i2c_algo_bit 13197 1 i915
shpchp 32128 0
video 18903 1 i915
parport_pc 31981 0
ppdev 17391 0
lp 13299 0
parport 40836 3 lp,ppdev,parport_pc
mac_hid 13037 0
via_rhine 27653 0
psmouse 91357 0
pata_acpi 12886 0
mii 13654 1 via_rhine
shargar@easy:~$ lsmod
Module Size Used by
bnep 18895 2
rfcomm 53664 0
bluetooth 342208 10 bnep,rfcomm
snd_intel8x0 33110 2
snd_ac97_codec 105709 1 snd_intel8x0
ac97_bus 12642 1 snd_ac97_codec
snd_pcm 85501 2 snd_ac97_codec,snd_intel8x0
snd_page_alloc 14230 2 snd_intel8x0,snd_pcm
snd_seq_midi 13132 0
snd_seq_midi_event 14475 1 snd_seq_midi
snd_rawmidi 25135 1 snd_seq_midi
pcmcia 51828 0
ipw2200 136401 0
snd_seq 55383 2 snd_seq_midi_event,snd_seq_midi
libipw 33144 1 ipw2200
snd_seq_device 14137 3 snd_seq,snd_rawmidi,snd_seq_midi
joydev 17101 0
i915 710013 2
snd_timer 28584 2 snd_pcm,snd_seq
lib80211 14040 2 libipw,ipw2200
yenta_socket 40201 0
drm_kms_helper 48868 1 i915
snd 60939 12 snd_ac97_codec,snd_intel8x0,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_seq_device,snd_seq_midi
lpc_ich 16864 0
cfg80211 409394 2 libipw,ipw2200
serio_raw 13230 0
pcmcia_rsrc 18319 1 yenta_socket
drm 244037 3 i915,drm_kms_helper
soundcore 12600 1 snd
pcmcia_core 22328 3 pcmcia,pcmcia_rsrc,yenta_socket
i2c_algo_bit 13197 1 i915
shpchp 32128 0
video 18903 1 i915
parport_pc 31981 0
ppdev 17391 0
lp 13299 0
parport 40836 3 lp,ppdev,parport_pc
mac_hid 13037 0
via_rhine 27653 0
psmouse 91357 0
pata_acpi 12886 0
mii 13654 1 via_rhine
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=off Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
shargar@easy:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=off Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ifconfig
eth0 Link encap:Ethernet HWaddr 00:40:d0:67:41:19
inet adr:192.168.1.13 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::240:d0ff:fe67:4119/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:4427 erreurs:0 :0 overruns:0 frame:0
TX packets:3554 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:3149043 (3.1 MB) Octets transmis:328247 (328.2 KB)
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:65536 Metric:1
Packets reçus:784 erreurs:0 :0 overruns:0 frame:0
TX packets:784 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:68240 (68.2 KB) Octets transmis:68240 (68.2 KB)
sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 No scan results
uname -r -m
3.13.0-46-generic i686
cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback
nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 [Connexion filaire 1] ------------------------------------------
Type: Wired
Driver: via-rhine
State: connected
Default: yes
HW Address: 00:40:D0:67:41:19
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.13
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.1
DNS: 192.168.1.1
- Device: eth1 -----------------------------------------------------------------
Type: 802.11 WiFi
Driver: ipw2200
State: unavailable
Default: no
HW Address: 00:0E:35:B4:83:24
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
sudo rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
et voilou tout y est je crois !
Hors ligne
#6 Le 16/03/2015, à 15:33
- toutafai
Re : comment contourner l'interupteur wifi clavier on/off
Cela me parait être tout bon.... ca m'as juste l'air d'etre la combinaison de touche qui merdasse...essaye d'appuyer (plusieur fois sur la combinaison de touche Fn + Fx (celle qui normalement active le wifi) AVANT qu'ubuntu ne soit démarré (juste âpres la mise sous tension, lors du menu grub par exemple), tu as peut être un voyant permettant de voir si le wifi est actif ou pas.
si rien, essaye cela
echo options ipw2200 disable=0 >> /etc/modprobe.d/ipw2200.conf && modprobe -r ipw2200 && modprobe ipw2200
si toujours rien que dit la commande
dmesg |grep ipw
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
Pages : 1