#1 Le 24/06/2015, à 22:44
- fgi
[Résolu][1404]Soft lockup au boot
Bonjour,
J'ai une 14.04 xubuntu.
s@xubuntu:~$ uname -r
3.13.0-51-genericDepuis aujourd'hui le boot plante avec un écran en damier lors de l'init graphique.
J'ai tenté en live-usb : idem.
Je suis passé par grub, démarrage en recovery mode, controle des espaces disques et des packages ... rien de notable ... puis reprise du boot, et là je récupère l'interface graphique mais avec une cascade de messages en mode popup (et une session qui fonctionne) :
Désolé, Ubuntu 14.04 a rencontré une erreur interneet le titre du rapport d'anomalie :
BUG: soft lockup - CPU#0 stuck for 23s! [Xorg:2813]un peu plus bas, dans la section "Failure" :
oopsPour info, il me semble avoir pris la dernière mise à jour du kernel, du coup avec Grub j'ai tenté de redémarrer avec un kernel antérieur, et c'est pareil. Plutot cohérent avec le fait que j'ai aussi le problème en live-usb ... ça ne semble pas lié à la version du kernel...
Du coup j'ai émis l'hypothèse d'un pb hard, à commencer par la carte graphique ou l'écran, mais le fait que ça redémarre (même très bancal) après le recovery mode, exclut cette piste.
Donc j'en appelle à votre science ;-)
Voici quelques infos utiles :
s@xubuntu:~$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.13.0-51-generic (buildd@kissel) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #84-Ubuntu SMP Wed Apr 15 12:11:46 UTC 2015 (Ubuntu 3.13.0-51.84-generic 3.13.11-ckt18)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007ffcffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007ffd0000-0x000000007ffddfff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007ffde000-0x000000007fffffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000ff780000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: Packard Bell NEC 00000000000000000000000/MS-7168, BIOS 080012 05/04/2005
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x7ffd0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [c00ff780]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x37800000-0x379fffff]
[ 0.000000] [mem 0x37800000-0x379fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x34000000-0x377fffff]
[ 0.000000] [mem 0x34000000-0x377fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x33ffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x37a00000-0x37bfdfff]
[ 0.000000] [mem 0x37a00000-0x37bfdfff] page 4k
[ 0.000000] BRK [0x01b99000, 0x01b99fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x35c24000-0x36e09fff]
[ 0.000000] ACPI: RSDP 000f9070 000014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 7ffd0000 000038 (v01 A M I OEMRSDT 05000504 MSFT 00000097)
[ 0.000000] ACPI: FACP 7ffd0200 000084 (v02 A M I OEMFACP 05000504 MSFT 00000097)
[ 0.000000] ACPI: DSDT 7ffd0430 0037BD (v01 0AAAA 0AAAA000 00000000 INTL 02002026)
[ 0.000000] ACPI: FACS 7ffde000 000040
[ 0.000000] ACPI: APIC 7ffd0390 000054 (v01 A M I OEMAPIC 05000504 MSFT 00000097)
[ 0.000000] ACPI: MCFG 7ffd03f0 00003C (v01 A M I OEMMCFG 05000504 MSFT 00000097)
[ 0.000000] ACPI: SSDT 7ffd3bf0 000D6E (v01 ATI ATIPATCH 00000001 INTL 02002026)
[ 0.000000] ACPI: OEMB 7ffde040 000056 (v01 A M I AMI_OEM 05000504 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1155MB HIGHMEM available.
[ 0.000000] 891MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 37bfe000
[ 0.000000] low ram: 0 - 37bfe000
[ 0.000000] BRK [0x01b9a000, 0x01b9afff] PGTABLE
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x37bfdfff]
[ 0.000000] HighMem [mem 0x37bfe000-0x7ffcffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x7ffcffff]
[ 0.000000] On node 0 totalpages: 524142
[ 0.000000] free_area_init_node: node 0, pgdat c199f780, node_mem_map f4c24020
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 1752 pages used for memmap
[ 0.000000] Normal zone: 224254 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2312 pages used for memmap
[ 0.000000] HighMem zone: 295890 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] SB4X0 revision 0x10
[ 0.000000] Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
[ 0.000000] e820: [mem 0x80000000-0xff77ffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f7be4000 s35520 r0 d21824 u57344
[ 0.000000] pcpu-alloc: s35520 r0 d21824 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522358
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-51-generic root=UUID=5b8e0c4d-8dd9-4953-8c6e-853cbcc40ebc ro recovery nomodeset
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 4193912 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (00037bfe:0007ffd0)
[ 0.000000] Memory: 2044900K/2096568K available (6553K kernel code, 641K rwdata, 2768K rodata, 880K init, 924K bss, 51668K reserved, 1183560K highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff14000 - 0xfffff000 ( 940 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
[ 0.000000] .init : 0xc19bd000 - 0xc1a99000 ( 880 kB)
[ 0.000000] .data : 0xc16667b4 - 0xc19bc600 (3415 kB)
[ 0.000000] .text : 0xc1000000 - 0xc16667b4 (6553 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=f7008000 soft=f700a000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2188.774 MHz processor
[ 0.008002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4377.54 BogoMIPS (lpj=8755096)
[ 0.008130] pid_max: default: 32768 minimum: 301
[ 0.008229] Security Framework initialized
[ 0.008312] AppArmor: AppArmor initialized
[ 0.012004] Yama: becoming mindful.
[ 0.012132] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.012198] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.012530] Initializing cgroup subsys memory
[ 0.012602] Initializing cgroup subsys devices
[ 0.012666] Initializing cgroup subsys freezer
[ 0.012729] Initializing cgroup subsys blkio
[ 0.012792] Initializing cgroup subsys perf_event
[ 0.012856] Initializing cgroup subsys hugetlb
[ 0.012948] mce: CPU supports 5 MCE banks
[ 0.013026] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
[ 0.013026] Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
[ 0.013026] tlb_flushall_shift: 4
[ 0.022543] Freeing SMP alternatives memory: 32K (c1a99000 - c1aa1000)
[ 0.023719] ACPI: Core revision 20131115
[ 0.026762] ACPI: All ACPI Tables successfully acquired
[ 0.027194] ftrace: allocating 27866 entries in 55 pages
[ 0.036118] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.036613] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.075924] smpboot: CPU0: AMD Athlon(tm) 64 Processor 3400+ (fam: 0f, model: 2f, stepping: 00)
[ 0.080000] Performance Events: AMD PMU driver.
[ 0.080000] ... version: 0
[ 0.080000] ... bit width: 48
[ 0.080000] ... generic registers: 4
[ 0.080000] ... value mask: 0000ffffffffffff
[ 0.080000] ... max period: 00007fffffffffff
[ 0.080000] ... fixed-purpose events: 0
[ 0.080000] ... event mask: 000000000000000f
[ 0.080000] x86: Booted up 1 node, 1 CPUs
[ 0.080000] smpboot: Total of 1 processors activated (4377.54 BogoMIPS)
[ 0.080000] devtmpfs: initialized
[ 0.080000] EVM: security.selinux
[ 0.080000] EVM: security.SMACK64
[ 0.080000] EVM: security.ima
[ 0.080000] EVM: security.capability
[ 0.080000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.080000] PM: Registering ACPI NVS region [mem 0x7ffde000-0x7fffffff] (139264 bytes)
[ 0.081120] pinctrl core: initialized pinctrl subsystem
[ 0.081269] regulator-dummy: no parameters
[ 0.081369] RTC time: 20:03:25, date: 06/24/15
[ 0.081474] NET: Registered protocol family 16
[ 0.081703] EISA bus registered
[ 0.081765] cpuidle: using governor ladder
[ 0.081826] cpuidle: using governor menu
[ 0.081890] node 0 link 0: io port [1000, ffffff]
[ 0.081894] TOM: 0000000080000000 aka 2048M
[ 0.081957] node 0 link 0: mmio [e0000000, efffffff]
[ 0.081960] node 0 link 0: mmio [80000000, dfffffff]
[ 0.081963] node 0 link 0: mmio [a0000, bffff]
[ 0.081965] node 0 link 0: mmio [f0000000, ffffffff]
[ 0.081968] bus: [bus 00-ff] on node 0 link 0
[ 0.081971] bus: 00 [io 0x0000-0xffff]
[ 0.081973] bus: 00 [mem 0x80000000-0xfcffffffff]
[ 0.081974] bus: 00 [mem 0x000a0000-0x000bffff]
[ 0.082032] ACPI: bus type PCI registered
[ 0.082094] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.082236] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.082315] PCI: not using MMCONFIG
[ 0.082933] PCI : PCI BIOS area is rw and x. Use pci=nobios if you want it NX.
[ 0.083090] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.083154] PCI: Using configuration type 1 for base access
[ 0.084611] bio: create slab <bio-0> at 0
[ 0.084842] ACPI: Added _OSI(Module Device)
[ 0.084903] ACPI: Added _OSI(Processor Device)
[ 0.084965] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.085027] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.086374] ACPI: Executed 3 blocks of module-level executable AML code
[ 0.088028] ACPI: Interpreter enabled
[ 0.088099] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
[ 0.088270] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[ 0.088451] ACPI: (supports S0 S3 S4 S5)
[ 0.088512] ACPI: Using IOAPIC for interrupt routing
[ 0.088655] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.089767] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.089844] PCI: Using MMCONFIG for extended config space
[ 0.089921] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.090091] ACPI: No dock devices found.
[ 0.095195] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.095264] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.096006] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.096179] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.096182] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.096184] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.096187] acpi PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[ 0.096190] acpi PNP0A03:00: host bridge window [mem 0x80000000-0xffffffff] (ignored)
[ 0.096192] PCI: root bus 00: hardware-probed resources
[ 0.096377] PCI host bridge to bus 0000:00
[ 0.096441] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.096505] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.096570] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfcffffffff]
[ 0.096636] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.096709] pci 0000:00:00.0: [1002:5950] type 00 class 0x060000
[ 0.096798] pci 0000:00:02.0: [1002:5a34] type 01 class 0x060400
[ 0.096835] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.096880] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 0.097013] pci 0000:00:11.0: [1002:437a] type 00 class 0x01018f
[ 0.097041] pci 0000:00:11.0: reg 0x10: [io 0xbc00-0xbc07]
[ 0.097054] pci 0000:00:11.0: reg 0x14: [io 0xb800-0xb803]
[ 0.097068] pci 0000:00:11.0: reg 0x18: [io 0xb400-0xb407]
[ 0.097081] pci 0000:00:11.0: reg 0x1c: [io 0xb000-0xb003]
[ 0.097095] pci 0000:00:11.0: reg 0x20: [io 0xac00-0xac0f]
[ 0.097108] pci 0000:00:11.0: reg 0x24: [mem 0xfebffc00-0xfebffdff]
[ 0.097122] pci 0000:00:11.0: reg 0x30: [mem 0xfeb00000-0xfeb7ffff pref]
[ 0.097176] pci 0000:00:11.0: supports D1 D2
[ 0.097258] pci 0000:00:12.0: [1002:4379] type 00 class 0x01018f
[ 0.097285] pci 0000:00:12.0: reg 0x10: [io 0xa800-0xa807]
[ 0.097299] pci 0000:00:12.0: reg 0x14: [io 0xa400-0xa403]
[ 0.097312] pci 0000:00:12.0: reg 0x18: [io 0xa000-0xa007]
[ 0.097326] pci 0000:00:12.0: reg 0x1c: [io 0x9c00-0x9c03]
[ 0.097339] pci 0000:00:12.0: reg 0x20: [io 0x9800-0x980f]
[ 0.097353] pci 0000:00:12.0: reg 0x24: [mem 0xfebff800-0xfebff9ff]
[ 0.097366] pci 0000:00:12.0: reg 0x30: [mem 0xfea80000-0xfeafffff pref]
[ 0.097420] pci 0000:00:12.0: supports D1 D2
[ 0.097505] pci 0000:00:13.0: [1002:4374] type 00 class 0x0c0310
[ 0.097529] pci 0000:00:13.0: reg 0x10: [mem 0xfebfe000-0xfebfefff]
[ 0.097675] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 0.097783] pci 0000:00:13.1: [1002:4375] type 00 class 0x0c0310
[ 0.097807] pci 0000:00:13.1: reg 0x10: [mem 0xfebfd000-0xfebfdfff]
[ 0.097953] pci 0000:00:13.1: System wakeup disabled by ACPI
[ 0.098061] pci 0000:00:13.2: [1002:4373] type 00 class 0x0c0320
[ 0.098088] pci 0000:00:13.2: reg 0x10: [mem 0xfebfc000-0xfebfcfff]
[ 0.098207] pci 0000:00:13.2: supports D1 D2
[ 0.098210] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.098265] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 0.098378] pci 0000:00:14.0: [1002:4372] type 00 class 0x0c0500
[ 0.098400] pci 0000:00:14.0: reg 0x10: [io 0x0b00-0x0b0f]
[ 0.098414] pci 0000:00:14.0: reg 0x14: [mem 0x00000000-0x000003ff]
[ 0.098473] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.098643] pci 0000:00:14.1: [1002:4376] type 00 class 0x01018a
[ 0.098667] pci 0000:00:14.1: reg 0x10: [io 0x01f0-0x01f7]
[ 0.098680] pci 0000:00:14.1: reg 0x14: [io 0x03f4-0x03f7]
[ 0.098693] pci 0000:00:14.1: reg 0x18: [io 0x0170-0x0177]
[ 0.098707] pci 0000:00:14.1: reg 0x1c: [io 0x0374-0x0377]
[ 0.098720] pci 0000:00:14.1: reg 0x20: [io 0xff00-0xff0f]
[ 0.098855] pci 0000:00:14.3: [1002:4377] type 00 class 0x060100
[ 0.100047] pci 0000:00:14.4: [1002:4371] type 01 class 0x060401
[ 0.100133] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 0.100236] pci 0000:00:14.5: [1002:4370] type 00 class 0x040100
[ 0.100260] pci 0000:00:14.5: reg 0x10: [mem 0xfebff400-0xfebff4ff]
[ 0.100405] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 0.100511] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
[ 0.100584] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
[ 0.100656] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
[ 0.100726] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
[ 0.100854] pci 0000:01:00.0: [10de:0162] type 00 class 0x030000
[ 0.100866] pci 0000:01:00.0: reg 0x10: [mem 0xfd000000-0xfdffffff]
[ 0.100878] pci 0000:01:00.0: reg 0x14: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.100890] pci 0000:01:00.0: reg 0x1c: [mem 0xfc000000-0xfcffffff 64bit]
[ 0.100903] pci 0000:01:00.0: reg 0x30: [mem 0xfe7e0000-0xfe7fffff pref]
[ 0.100970] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.101056] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.101122] pci 0000:00:02.0: bridge window [mem 0xfa700000-0xfe7fffff]
[ 0.101126] pci 0000:00:02.0: bridge window [mem 0xbff00000-0xdfefffff pref]
[ 0.101181] pci 0000:02:03.0: [10ec:8139] type 00 class 0x020000
[ 0.101209] pci 0000:02:03.0: reg 0x10: [io 0x8800-0x88ff]
[ 0.101225] pci 0000:02:03.0: reg 0x14: [mem 0xfe8fe400-0xfe8fe4ff]
[ 0.101296] pci 0000:02:03.0: reg 0x30: [mem 0xfe8e0000-0xfe8effff pref]
[ 0.101344] pci 0000:02:03.0: supports D1 D2
[ 0.101347] pci 0000:02:03.0: PME# supported from D1 D2 D3hot D3cold
[ 0.101412] pci 0000:02:04.0: [1106:3044] type 00 class 0x0c0010
[ 0.101441] pci 0000:02:04.0: reg 0x10: [mem 0xfe8fd800-0xfe8fdfff]
[ 0.101458] pci 0000:02:04.0: reg 0x14: [io 0x8c00-0x8c7f]
[ 0.101578] pci 0000:02:04.0: supports D2
[ 0.101580] pci 0000:02:04.0: PME# supported from D2 D3hot D3cold
[ 0.101676] pci 0000:00:14.4: PCI bridge to [bus 02] (subtractive decode)
[ 0.101748] pci 0000:00:14.4: bridge window [io 0x8000-0x8fff]
[ 0.101754] pci 0000:00:14.4: bridge window [mem 0xfe800000-0xfe8fffff]
[ 0.101760] pci 0000:00:14.4: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.101763] pci 0000:00:14.4: bridge window [mem 0x80000000-0xfcffffffff] (subtractive decode)
[ 0.101766] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.101780] pci_bus 0000:00: on NUMA node 0
[ 0.102364] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.103078] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.103789] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.104482] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.105193] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.105906] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 0.106243] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.106954] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.107690] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.107718] Found 1 acpi root devices
[ 0.107859] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 0.107923] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.108002] vgaarb: loaded
[ 0.108062] vgaarb: bridge control possible 0000:01:00.0
[ 0.108411] SCSI subsystem initialized
[ 0.108537] libata version 3.00 loaded.
[ 0.108567] ACPI: bus type USB registered
[ 0.108653] usbcore: registered new interface driver usbfs
[ 0.108729] usbcore: registered new interface driver hub
[ 0.108815] usbcore: registered new device driver usb
[ 0.109004] PCI: Using ACPI for IRQ routing
[ 0.109068] PCI: pci_cache_line_size set to 64 bytes
[ 0.109131] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.109134] e820: reserve RAM buffer [mem 0x7ffd0000-0x7fffffff]
[ 0.109250] NetLabel: Initializing
[ 0.109311] NetLabel: domain hash size = 128
[ 0.109372] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.109449] NetLabel: unlabeled traffic allowed by default
[ 0.109630] Switched to clocksource refined-jiffies
[ 0.116750] AppArmor: AppArmor Filesystem Enabled
[ 0.116866] pnp: PnP ACPI init
[ 0.116944] ACPI: bus type PNP registered
[ 0.117070] pnp 00:00: [dma 4]
[ 0.117104] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.117146] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.117174] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.117209] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.117765] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.117831] system 00:04: [io 0x040b] has been reserved
[ 0.117895] system 00:04: [io 0x04d6] has been reserved
[ 0.117963] system 00:04: [io 0x0c00-0x0c01] has been reserved
[ 0.118028] system 00:04: [io 0x0c14] has been reserved
[ 0.118092] system 00:04: [io 0x0c50-0x0c51] has been reserved
[ 0.118157] system 00:04: [io 0x0c52] has been reserved
[ 0.118221] system 00:04: [io 0x0c6c] has been reserved
[ 0.118285] system 00:04: [io 0x0c6f] has been reserved
[ 0.118350] system 00:04: [io 0x0cd4-0x0cd5] has been reserved
[ 0.118415] system 00:04: [io 0x0cd6-0x0cd7] has been reserved
[ 0.118480] system 00:04: [io 0x0cd8-0x0cdf] has been reserved
[ 0.118545] system 00:04: [io 0x0800-0x089f] could not be reserved
[ 0.118611] system 00:04: [io 0x0900-0x090f] has been reserved
[ 0.118675] system 00:04: [io 0x0910-0x091f] has been reserved
[ 0.118742] system 00:04: [mem 0xfff80000-0xffffffff] has been reserved
[ 0.118808] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.118865] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.118973] system 00:06: [io 0x0e00-0x0e7f] has been reserved
[ 0.119038] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.119113] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.119179] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.119246] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.119304] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.119370] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.119522] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.119589] system 00:09: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.119656] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.119722] system 00:09: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.119789] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.119905] pnp: PnP ACPI: found 10 devices
[ 0.119966] ACPI: bus type PNP unregistered
[ 0.120008] PnPBIOS: Disabled by ACPI PNP
[ 0.156281] Switched to clocksource acpi_pm
[ 0.156367] pci 0000:00:14.0: BAR 1: assigned [mem 0x80000000-0x800003ff]
[ 0.156438] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.156503] pci 0000:00:02.0: bridge window [mem 0xfa700000-0xfe7fffff]
[ 0.156570] pci 0000:00:02.0: bridge window [mem 0xbff00000-0xdfefffff pref]
[ 0.156648] pci 0000:00:14.4: PCI bridge to [bus 02]
[ 0.156713] pci 0000:00:14.4: bridge window [io 0x8000-0x8fff]
[ 0.156783] pci 0000:00:14.4: bridge window [mem 0xfe800000-0xfe8fffff]
[ 0.156858] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.156860] pci_bus 0000:00: resource 5 [mem 0x80000000-0xfcffffffff]
[ 0.156863] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.156866] pci_bus 0000:01: resource 1 [mem 0xfa700000-0xfe7fffff]
[ 0.156869] pci_bus 0000:01: resource 2 [mem 0xbff00000-0xdfefffff pref]
[ 0.156872] pci_bus 0000:02: resource 0 [io 0x8000-0x8fff]
[ 0.156875] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff]
[ 0.156877] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.156880] pci_bus 0000:02: resource 5 [mem 0x80000000-0xfcffffffff]
[ 0.156883] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.156926] NET: Registered protocol family 2
[ 0.157249] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.157339] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.157446] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.157553] TCP: reno registered
[ 0.157615] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.157688] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.157811] NET: Registered protocol family 1
[ 0.157883] pci 0000:00:00.0: MSI quirk detected; MSI disabled
[ 0.304155] pci 0000:01:00.0: Video device with shadowed ROM
[ 0.304165] PCI: CLS 64 bytes, default 64
[ 0.304231] Trying to unpack rootfs image as initramfs...
[ 0.730231] Freeing initrd memory: 18328K (f5c24000 - f6e0a000)
[ 0.730474] microcode: AMD CPU family 0xf not supported
[ 0.730538] Scanning for low memory corruption every 60 seconds
[ 0.730893] Initialise system trusted keyring
[ 0.731009] audit: initializing netlink socket (disabled)
[ 0.731086] type=2000 audit(1435176205.727:1): initialized
[ 0.757312] bounce pool size: 64 pages
[ 0.757384] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.758810] zbud: loaded
[ 0.758946] VFS: Disk quotas dquot_6.5.2
[ 0.759059] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.759647] fuse init (API version 7.22)
[ 0.759788] msgmni has been set to 1718
[ 0.759917] Key type big_key registered
[ 0.760297] Key type asymmetric registered
[ 0.760359] Asymmetric key parser 'x509' registered
[ 0.760459] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.760561] io scheduler noop registered
[ 0.760623] io scheduler deadline registered (default)
[ 0.760712] io scheduler cfq registered
[ 0.760931] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.761013] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.761141] ipmi message handler version 39.2
[ 0.761280] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.761361] ACPI: Power Button [PWRB]
[ 0.761463] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.761539] ACPI: Power Button [PWRF]
[ 0.761634] ACPI: duty_cycle spans bit 4
[ 0.761774] GHES: HEST is not enabled!
[ 0.761927] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.763297] Linux agpgart interface v0.103
[ 0.765016] brd: module loaded
[ 0.765442] isapnp: Scanning for PnP cards...
[ 0.815109] loop: module loaded
[ 0.815733] libphy: Fixed MDIO Bus: probed
[ 0.815931] tun: Universal TUN/TAP device driver, 1.6
[ 0.815993] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.816110] PPP generic driver version 2.4.2
[ 0.816214] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.816281] ehci-pci: EHCI PCI platform driver
[ 0.816460] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 0.816531] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 1
[ 0.816683] ehci-pci 0000:00:13.2: irq 19, io mem 0xfebfc000
[ 0.860411] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 0.860580] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.860646] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.860722] usb usb1: Product: EHCI Host Controller
[ 0.860785] usb usb1: Manufacturer: Linux 3.13.0-51-generic ehci_hcd
[ 0.860849] usb usb1: SerialNumber: 0000:00:13.2
[ 0.861020] hub 1-0:1.0: USB hub found
[ 0.861089] hub 1-0:1.0: 8 ports detected
[ 0.861350] ehci-platform: EHCI generic platform driver
[ 0.861422] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.861487] ohci-pci: OHCI PCI platform driver
[ 0.861607] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 0.861674] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 0.861765] ohci-pci 0000:00:13.0: irq 19, io mem 0xfebfe000
[ 0.996777] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.996843] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.996919] usb usb2: Product: OHCI PCI host controller
[ 0.996982] usb usb2: Manufacturer: Linux 3.13.0-51-generic ohci_hcd
[ 0.997047] usb usb2: SerialNumber: 0000:00:13.0
[ 0.997198] hub 2-0:1.0: USB hub found
[ 0.997269] hub 2-0:1.0: 4 ports detected
[ 0.997480] ohci-pci 0000:00:13.1: OHCI PCI host controller
[ 0.997550] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 0.997640] ohci-pci 0000:00:13.1: irq 19, io mem 0xfebfd000
[ 1.132381] isapnp: No Plug & Play device found
[ 1.132474] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.132540] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.132616] usb usb3: Product: OHCI PCI host controller
[ 1.132679] usb usb3: Manufacturer: Linux 3.13.0-51-generic ohci_hcd
[ 1.132744] usb usb3: SerialNumber: 0000:00:13.1
[ 1.132890] hub 3-0:1.0: USB hub found
[ 1.134651] hub 3-0:1.0: 4 ports detected
[ 1.134809] ohci-platform: OHCI generic platform driver
[ 1.134880] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.135021] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.135086] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.135966] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.136108] mousedev: PS/2 mouse device common for all mice
[ 1.136281] rtc_cmos 00:01: RTC can wake from S4
[ 1.136484] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 1.136576] rtc_cmos 00:01: alarms up to one month, 114 bytes nvram
[ 1.136716] device-mapper: uevent: version 1.0.3
[ 1.136843] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[ 1.136937] platform eisa.0: Probing EISA bus 0
[ 1.137001] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 1.137067] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 1.137133] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 1.137198] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 1.137264] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 1.137329] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 1.137394] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 1.137459] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 1.137524] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 1.137589] platform eisa.0: EISA: Detected 0 cards
[ 1.137657] cpufreq-nforce2: No nForce2 chipset.
[ 1.137720] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.137928] TCP: cubic registered
[ 1.138096] NET: Registered protocol family 10
[ 1.138369] NET: Registered protocol family 17
[ 1.138441] Key type dns_resolver registered
[ 1.138627] Using IPI No-Shortcut mode
[ 1.138762] Loading compiled-in X.509 certificates
[ 1.142754] Loaded X.509 cert 'Magrathea: Glacier signing key: 1f88723dce4086a12303dadd54a7ae35e9e44d58'
[ 1.142845] registered taskstats version 1
[ 1.145433] Key type trusted registered
[ 1.150138] Key type encrypted registered
[ 1.150208] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.150272] IMA: No TPM chip found, activating TPM-bypass!
[ 1.150569] regulator-dummy: disabling
[ 1.150671] Magic number: 3:439:94
[ 1.150832] rtc_cmos 00:01: setting system clock to 2015-06-24 20:03:26 UTC (1435176206)
[ 1.151029] powernow-k8: fid 0xe (2200 MHz), vid 0x6
[ 1.151092] powernow-k8: fid 0xc (2000 MHz), vid 0x8
[ 1.151155] powernow-k8: fid 0xa (1800 MHz), vid 0xa
[ 1.151217] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[ 1.151302] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3400+ (1 cpu cores) (version 2.20.00)
[ 1.151384] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.151447] EDD information not available.
[ 1.151551] PM: Hibernation image not present or could not be loaded.
[ 1.152197] Freeing unused kernel memory: 880K (c19bd000 - c1a99000)
[ 1.152326] Write protecting the kernel text: 6556k
[ 1.152455] Write protecting the kernel read-only data: 2772k
[ 1.152519] NX-protecting the kernel data: 5732k
[ 1.171810] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.172219] systemd-udevd[89]: starting version 204
[ 1.213078] sata_sil 0000:00:11.0: version 2.4
[ 1.224716] scsi0 : sata_sil
[ 1.235367] scsi1 : sata_sil
[ 1.235498] ata1: SATA max UDMA/100 mmio m512@0xfebffc00 tf 0xfebffc80 irq 23
[ 1.235566] ata2: SATA max UDMA/100 mmio m512@0xfebffc00 tf 0xfebffcc0 irq 23
[ 1.244201] scsi2 : sata_sil
[ 1.245117] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.245207] 8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.248395] scsi3 : sata_sil
[ 1.248520] ata3: SATA max UDMA/100 mmio m512@0xfebff800 tf 0xfebff880 irq 22
[ 1.248587] ata4: SATA max UDMA/100 mmio m512@0xfebff800 tf 0xfebff8c0 irq 22
[ 1.251817] scsi4 : pata_atiixp
[ 1.257764] scsi5 : pata_atiixp
[ 1.257891] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 1.257956] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 1.273296] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.274632] 8139too 0000:02:03.0 eth0: RealTek RTL8139 at 0x00018800, 00:11:09:19:9c:15, IRQ 20
[ 1.376069] firewire_ohci 0000:02:04.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 1.432583] ata6.00: ATAPI: LITE-ON DVDRW SOHW-1633S, B9S5, max UDMA/66
[ 1.448511] ata6.00: configured for UDMA/66
[ 1.552061] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.568060] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.576666] ata3.00: ATA-9: WDC WD10EZEX-08M2NA0, 01.01A01, max UDMA/100
[ 1.576732] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.578304] ata1.00: ATA-8: KINGSTON SV300S37A120G, 600ABBF0, max UDMA/133
[ 1.578370] ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 0/32)
[ 1.584778] ata3.00: configured for UDMA/100
[ 1.585920] ata1.00: configured for UDMA/100
[ 1.586105] scsi 0:0:0:0: Direct-Access ATA KINGSTON SV300S3 600A PQ: 0 ANSI: 5
[ 1.586537] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.586703] sd 0:0:0:0: [sda] Write Protect is off
[ 1.586767] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.586795] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.587160] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.588156] sda: sda1 sda2 < sda5 >
[ 1.588658] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.728045] tsc: Refined TSC clocksource calibration: 2188.787 MHz
[ 1.876389] firewire_core 0000:02:04.0: created device fw0: GUID 0010dc000096798a, S400
[ 1.896027] usb 3-1: new low-speed USB device number 2 using ohci-pci
[ 1.904046] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.904250] scsi 2:0:0:0: Direct-Access ATA WDC WD10EZEX-08M 01.0 PQ: 0 ANSI: 5
[ 1.904516] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.904593] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[ 1.904719] sd 2:0:0:0: [sdb] Write Protect is off
[ 1.904783] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.904824] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 1.904909] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.927249] sdb: sdb1 sdb2
[ 1.927613] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 2.106758] usb 3-1: New USB device found, idVendor=047d, idProduct=1020
[ 2.106829] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.106895] usb 3-1: Product: Kensington Expert Mouse
[ 2.106958] usb 3-1: Manufacturer: Kensington
[ 2.118714] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.130431] usbcore: registered new interface driver usbhid
[ 2.130500] usbhid: USB HID core driver
[ 2.136262] input: Kensington Kensington Expert Mouse as /devices/pci0000:00/0000:00:13.1/usb3/3-1/3-1:1.0/input/input3
[ 2.137198] hid-generic 0003:047D:1020.0001: input,hidraw0: USB HID v1.10 Mouse [Kensington Kensington Expert Mouse] on usb-0000:00:13.1-1/input0
[ 2.224049] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.225013] scsi 5:0:0:0: CD-ROM LITE-ON DVDRW SOHW-1633S B9S5 PQ: 0 ANSI: 5
[ 2.227245] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 2.227310] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.227480] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 2.227630] sr 5:0:0:0: Attached scsi generic sg2 type 5
[ 2.284058] usb 2-4: new full-speed USB device number 2 using ohci-pci
[ 2.297560] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 2.297631] EXT4-fs (sda1): write access will be enabled during recovery
[ 2.363588] EXT4-fs (sda1): recovery complete
[ 2.364279] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.469259] random: init urandom read with 69 bits of entropy available
[ 2.493119] usb 2-4: New USB device found, idVendor=058f, idProduct=9360
[ 2.493191] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.493258] usb 2-4: Product: USB Reader
[ 2.493320] usb 2-4: Manufacturer:
[ 2.493381] usb 2-4: SerialNumber: 2004888
[ 2.728079] Switched to clocksource tsc
[ 3.714894] systemd-udevd[213]: starting version 204
[ 3.851248] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 3.866501] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 4.006666] [drm] Initialized drm 1.1.0 20060810
[ 4.056411] random: nonblocking pool is initialized
[ 4.091079] usb-storage 2-4:1.0: USB Mass Storage device detected
[ 4.117418] scsi6 : usb-storage 2-4:1.0
[ 4.121759] usbcore: registered new interface driver usb-storage
[ 4.373484] wmi: Mapper loaded
[ 4.794230] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.123109] scsi 6:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 5.129141] scsi 6:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 5.135105] scsi 6:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 5.141121] scsi 6:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 5.141472] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 5.141630] sd 6:0:0:1: Attached scsi generic sg4 type 0
[ 5.141794] sd 6:0:0:2: Attached scsi generic sg5 type 0
[ 5.141942] sd 6:0:0:3: Attached scsi generic sg6 type 0
[ 5.431127] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 5.441118] sd 6:0:0:1: [sdd] Attached SCSI removable disk
[ 5.451138] sd 6:0:0:2: [sde] Attached SCSI removable disk
[ 5.461118] sd 6:0:0:3: [sdf] Attached SCSI removable disk
[ 76.840218] Adding 2099196k swap on /dev/sdb1. Priority:-1 extents:1 across:2099196k FS
[ 76.887043] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 77.188691] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 210.211813] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 210.239146] JFS: nTxBlock = 8192, nTxLock = 65536
[ 210.267734] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 210.319152] QNX4 filesystem 0.2.3 registered.
[ 210.342426] xor: measuring software checksum speed
[ 210.380004] pIII_sse : 6820.000 MB/sec
[ 210.420004] prefetch64-sse: 6826.000 MB/sec
[ 210.420006] xor: using function: prefetch64-sse (6826.000 MB/sec)
[ 210.496027] raid6: mmxx1 1839 MB/s
[ 210.564004] raid6: mmxx2 3338 MB/s
[ 210.632049] raid6: sse1x1 653 MB/s
[ 210.700024] raid6: sse1x2 1012 MB/s
[ 210.768016] raid6: sse2x1 1035 MB/s
[ 210.836039] raid6: sse2x2 1667 MB/s
[ 210.904028] raid6: int32x1 901 MB/s
[ 210.972053] raid6: int32x2 892 MB/s
[ 211.040088] raid6: int32x4 739 MB/s
[ 211.108081] raid6: int32x8 495 MB/s
[ 211.108083] raid6: using algorithm mmxx2 (3338 MB/s)
[ 211.108085] raid6: using intx1 recovery algorithm
[ 211.167570] bio: create slab <bio-1> at 1
[ 211.172429] Btrfs loaded
[ 235.886709] init: plymouth-upstart-bridge main process (3103) terminated with status 1
[ 235.886726] init: plymouth-upstart-bridge main process ended, respawning
[ 235.959794] lp: driver loaded but no devices found
[ 235.990681] ppdev: user-space parallel port driver
[ 236.009416] init: plymouth-upstart-bridge main process (3134) terminated with status 1
[ 236.009434] init: plymouth-upstart-bridge main process ended, respawning
[ 236.092180] init: plymouth-upstart-bridge main process (3154) terminated with status 1
[ 236.092198] init: plymouth-upstart-bridge main process ended, respawning
[ 238.550421] Bluetooth: Core ver 2.17
[ 238.551368] NET: Registered protocol family 31
[ 238.551374] Bluetooth: HCI device and connection manager initialized
[ 238.551385] Bluetooth: HCI socket layer initialized
[ 238.551388] Bluetooth: L2CAP socket layer initialized
[ 238.551400] Bluetooth: SCO socket layer initialized
[ 238.606188] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 238.606194] Bluetooth: BNEP filters: protocol multicast
[ 238.606205] Bluetooth: BNEP socket layer initialized
[ 238.708384] init: failsafe main process (3594) killed by TERM signal
[ 238.771038] Bluetooth: RFCOMM TTY layer initialized
[ 238.771051] Bluetooth: RFCOMM socket layer initialized
[ 238.771062] Bluetooth: RFCOMM ver 1.11
[ 239.239936] type=1400 audit(1435176444.585:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=3729 comm="apparmor_parser"
[ 239.239944] type=1400 audit(1435176444.585:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=3729 comm="apparmor_parser"
[ 239.257907] type=1400 audit(1435176444.605:4): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=3729 comm="apparmor_parser"
[ 239.272368] 8139too 0000:02:03.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 239.595775] init: cups main process (3733) killed by HUP signal
[ 239.595788] init: cups main process ended, respawning
[ 239.687602] type=1400 audit(1435176445.033:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=3815 comm="apparmor_parser"
[ 239.687610] type=1400 audit(1435176445.033:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=3815 comm="apparmor_parser"
[ 239.687975] type=1400 audit(1435176445.033:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="chromium" pid=3815 comm="apparmor_parser"
[ 239.729488] type=1400 audit(1435176445.077:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=3816 comm="apparmor_parser"
[ 239.729496] type=1400 audit(1435176445.077:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=3816 comm="apparmor_parser"
[ 239.729500] type=1400 audit(1435176445.077:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=3816 comm="apparmor_parser"
[ 239.730109] type=1400 audit(1435176445.077:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=3816 comm="apparmor_parser"
[ 243.654210] init: plymouth-upstart-bridge main process ended, respawning
[ 243.689174] init: plymouth-upstart-bridge main process (4277) terminated with status 1
[ 243.689194] init: plymouth-upstart-bridge main process ended, respawning
[ 253.508912] init: plymouth-stop pre-start process (5076) terminated with status 1
[ 269.527776] audit_printk_skb: 87 callbacks suppressed
[ 269.527783] type=1400 audit(1435176476.781:41): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=5548 comm="apparmor_parser"
[ 269.527793] type=1400 audit(1435176476.781:42): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=5548 comm="apparmor_parser"
[ 269.532470] type=1400 audit(1435176476.789:43): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=5548 comm="apparmor_parser"
[ 313.504169] tsc: Marking TSC unstable due to cpufreq changes
[ 313.504229] Switched to clocksource acpi_pm
s@xubuntu:~$ s@xubuntu:~$ sudo lshw
[sudo] password for s:
xubuntu
description: Ordinateur de Bureau
produit: 00000000000000000000000 (To Be Filled By O.E.M.)
fabriquant: Packard Bell NEC
version: PB34101002
numéro de série: 047430120454
bits: 32 bits
fonctionnalités: smbios-2.3 dmi-2.3 smp-1.4 smp
configuration: boot=normal chassis=desktop cpus=1 family=To Be Filled By O.E.M. sku=To Be Filled By O.E.M. uuid=389D43BD-2BFA-D911-8000-4E45435F4349
*-core
description: Carte mère
produit: MS-7168
fabriquant: NEC COMPUTERS INTERNATIONAL
identifiant matériel: 0
version: 1.0
emplacement: To Be Filled By O.E.M.
*-firmware
description: BIOS
fabriquant: American Megatrends Inc.
identifiant matériel: 0
version: 080012
date: 05/04/2005
taille: 64KiB
capacité: 448KiB
fonctionnalités: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification netboot
*-cpu
description: CPU
produit: AMD Athlon(tm) 64 Processor 3400+
fabriquant: Advanced Micro Devices [AMD]
identifiant matériel: 4
information bus: cpu@0
version: 15.15.0
numéro de série: To Be Filled By O.E.M.
emplacement: CPU 1
taille: 1GHz
capacité: 2200MHz
bits: 64 bits
horloge: 200MHz
fonctionnalités: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt x86-64 3dnowext 3dnow pni lahf_lm vmmcall cpufreq
*-cache:0
description: L1 cache
identifiant matériel: 5
emplacement: L1-Cache
taille: 128KiB
fonctionnalités: pipeline-burst internal varies data
*-cache:1
description: L2 cache
identifiant matériel: 6
emplacement: L2-Cache
taille: 512KiB
capacité: 512KiB
fonctionnalités: pipeline-burst internal varies unified
*-memory
description: Mémoire Système
identifiant matériel: 2d
emplacement: Carte mère
taille: 2GiB
*-bank:0
description: DIMM DDR Synchrone 400 MHz (2,5 ns)
produit: PartNum0
fabriquant: Manufacturer0
identifiant matériel: 0
numéro de série: SerNum0
emplacement: DIMM0
taille: 512MiB
bits: 64 bits
horloge: 400MHz (2.5ns)
*-bank:1
description: DIMM DDR Synchrone 400 MHz (2,5 ns)
produit: PartNum1
fabriquant: Manufacturer1
identifiant matériel: 1
numéro de série: SerNum1
emplacement: DIMM1
taille: 512MiB
bits: 64 bits
horloge: 400MHz (2.5ns)
*-bank:2
description: DIMM DDR Synchrone 400 MHz (2,5 ns)
produit: PartNum2
fabriquant: Manufacturer2
identifiant matériel: 2
numéro de série: SerNum2
emplacement: DIMM2
taille: 512MiB
bits: 64 bits
horloge: 400MHz (2.5ns)
*-bank:3
description: DIMM DDR Synchrone 400 MHz (2,5 ns)
produit: PartNum3
fabriquant: Manufacturer3
identifiant matériel: 3
numéro de série: SerNum3
emplacement: DIMM3
taille: 512MiB
bits: 64 bits
horloge: 400MHz (2.5ns)
*-pci:0
description: Host bridge
produit: RS480/RS482/RS485 Host Bridge
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 100
information bus: pci@0000:00:00.0
version: 01
bits: 32 bits
horloge: 66MHz
*-pci:0
description: PCI bridge
produit: RS4xx PCI Express Port [ext gfx]
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 2
information bus: pci@0000:00:02.0
version: 00
bits: 32 bits
horloge: 33MHz
fonctionnalités: pci pm pciexpress msi ht normal_decode bus_master cap_list
configuration: driver=pcieport
ressources: irq:0 mémoire:fa700000-fe7fffff mémoire:bff00000-dfefffff
*-display NON-RÉCLAMÉ
description: VGA compatible controller
produit: NV44 [GeForce 6200 SE TurboCache]
fabriquant: NVIDIA Corporation
identifiant matériel: 0
information bus: pci@0000:01:00.0
version: a1
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm msi pciexpress vga_controller bus_master cap_list
configuration: latency=0
ressources: mémoire:fd000000-fdffffff mémoire:c0000000-cfffffff mémoire:fc000000-fcffffff mémoire:fe7e0000-fe7fffff
*-ide:0
description: IDE interface
produit: IXP SB400 Serial ATA Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 11
information bus: pci@0000:00:11.0
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: ide pm msi bus_master cap_list rom
configuration: driver=sata_sil latency=64
ressources: irq:23 portE/S:bc00(taille=8) portE/S:b800(taille=4) portE/S:b400(taille=8) portE/S:b000(taille=4) portE/S:ac00(taille=16) mémoire:febffc00-febffdff mémoire:feb00000-feb7ffff
*-ide:1
description: IDE interface
produit: IXP SB4x0 Serial ATA Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 12
information bus: pci@0000:00:12.0
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: ide pm msi bus_master cap_list rom
configuration: driver=sata_sil latency=64
ressources: irq:22 portE/S:a800(taille=8) portE/S:a400(taille=4) portE/S:a000(taille=8) portE/S:9c00(taille=4) portE/S:9800(taille=16) mémoire:febff800-febff9ff mémoire:fea80000-feafffff
*-usb:0
description: USB controller
produit: IXP SB4x0 USB Host Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 13
information bus: pci@0000:00:13.0
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: msi ohci bus_master cap_list
configuration: driver=ohci-pci latency=64
ressources: irq:19 mémoire:febfe000-febfefff
*-usb:1
description: USB controller
produit: IXP SB4x0 USB Host Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 13.1
information bus: pci@0000:00:13.1
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: msi ohci bus_master cap_list
configuration: driver=ohci-pci latency=64
ressources: irq:19 mémoire:febfd000-febfdfff
*-usb:2
description: USB controller
produit: IXP SB4x0 USB2 Host Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 13.2
information bus: pci@0000:00:13.2
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: pm msi ehci bus_master cap_list
configuration: driver=ehci-pci latency=64
ressources: irq:19 mémoire:febfc000-febfcfff
*-serial
description: SMBus
produit: IXP SB4x0 SMBus Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 14
information bus: pci@0000:00:14.0
version: 10
bits: 32 bits
horloge: 66MHz
fonctionnalités: ht cap_list
configuration: driver=piix4_smbus latency=0
ressources: irq:0 portE/S:b00(taille=16) mémoire:80000000-800003ff
*-ide:2
description: IDE interface
produit: IXP SB4x0 IDE Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 14.1
information bus: pci@0000:00:14.1
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: ide msi bus_master cap_list
configuration: driver=pata_atiixp latency=64
ressources: irq:16 portE/S:1f0(taille=8) portE/S:3f6 portE/S:170(taille=8) portE/S:376 portE/S:ff00(taille=16)
*-isa
description: ISA bridge
produit: IXP SB4x0 PCI-ISA Bridge
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 14.3
information bus: pci@0000:00:14.3
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: isa bus_master
configuration: latency=0
*-pci:1
description: PCI bridge
produit: IXP SB4x0 PCI-PCI Bridge
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 14.4
information bus: pci@0000:00:14.4
version: 00
bits: 32 bits
horloge: 66MHz
fonctionnalités: pci subtractive_decode bus_master
ressources: portE/S:8000(taille=4096) mémoire:fe800000-fe8fffff
*-network
description: Ethernet interface
produit: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter
fabriquant: Realtek Semiconductor Co., Ltd.
identifiant matériel: 3
information bus: pci@0000:02:03.0
nom logique: eth0
version: 10
numéro de série: 00:11:09:19:9c:15
taille: 100Mbit/s
capacité: 100Mbit/s
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.1.26 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100Mbit/s
ressources: irq:20 portE/S:8800(taille=256) mémoire:fe8fe400-fe8fe4ff mémoire:fe8e0000-fe8effff
*-firewire
description: FireWire (IEEE 1394)
produit: VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller
fabriquant: VIA Technologies, Inc.
identifiant matériel: 4
information bus: pci@0000:02:04.0
version: 80
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm ohci bus_master cap_list
configuration: driver=firewire_ohci latency=64 maxlatency=32
ressources: irq:9 mémoire:fe8fd800-fe8fdfff portE/S:8c00(taille=128)
*-multimedia
description: Multimedia audio controller
produit: IXP SB400 AC'97 Audio Controller
fabriquant: Advanced Micro Devices, Inc. [AMD/ATI]
identifiant matériel: 14.5
information bus: pci@0000:00:14.5
version: 01
bits: 32 bits
horloge: 66MHz
fonctionnalités: msi bus_master cap_list
configuration: driver=snd_atiixp latency=64 mingnt=2
ressources: irq:17 mémoire:febff400-febff4ff
*-pci:1
description: Host bridge
produit: K8 [Athlon64/Opteron] HyperTransport Technology Configuration
fabriquant: Advanced Micro Devices, Inc. [AMD]
identifiant matériel: 101
information bus: pci@0000:00:18.0
version: 00
bits: 32 bits
horloge: 33MHz
*-pci:2
description: Host bridge
produit: K8 [Athlon64/Opteron] Address Map
fabriquant: Advanced Micro Devices, Inc. [AMD]
identifiant matériel: 102
information bus: pci@0000:00:18.1
version: 00
bits: 32 bits
horloge: 33MHz
*-pci:3
description: Host bridge
produit: K8 [Athlon64/Opteron] DRAM Controller
fabriquant: Advanced Micro Devices, Inc. [AMD]
identifiant matériel: 103
information bus: pci@0000:00:18.2
version: 00
bits: 32 bits
horloge: 33MHz
*-pci:4
description: Host bridge
produit: K8 [Athlon64/Opteron] Miscellaneous Control
fabriquant: Advanced Micro Devices, Inc. [AMD]
identifiant matériel: 104
information bus: pci@0000:00:18.3
version: 00
bits: 32 bits
horloge: 33MHz
configuration: driver=k8temp
ressources: irq:0
*-scsi:0
identifiant matériel: 1
nom logique: scsi0
fonctionnalités: emulated
*-disk
description: ATA Disk
produit: KINGSTON SV300S3
identifiant matériel: 0.0.0
information bus: scsi@0:0.0.0
nom logique: /dev/sda
version: 600A
numéro de série: 50026B784C007D4A
taille: 111GiB (120GB)
fonctionnalités: partitioned partitioned:dos
configuration: ansiversion=5 sectorsize=512 signature=0001a505
*-volume:0
description: Volume EXT4
fabriquant: Linux
identifiant matériel: 1
information bus: scsi@0:0.0.0,1
nom logique: /dev/sda1
nom logique: /
version: 1.0
numéro de série: 5b8e0c4d-8dd9-4953-8c6e-853cbcc40ebc
taille: 109GiB
capacité: 109GiB
fonctionnalités: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized
configuration: created=2015-02-28 17:52:57 filesystem=ext4 lastmountpoint=/ modified=2015-06-24 22:04:42 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2015-06-24 22:04:42 state=mounted
*-volume:1
description: Extended partition
identifiant matériel: 2
information bus: scsi@0:0.0.0,2
nom logique: /dev/sda2
taille: 2045MiB
capacité: 2045MiB
fonctionnalités: primary extended partitioned partitioned:extended
*-logicalvolume
description: Linux swap / Solaris partition
identifiant matériel: 5
nom logique: /dev/sda5
capacité: 2045MiB
fonctionnalités: nofs
*-scsi:1
identifiant matériel: 2
nom logique: scsi2
fonctionnalités: emulated
*-disk
description: ATA Disk
produit: WDC WD10EZEX-08M
fabriquant: Western Digital
identifiant matériel: 0.0.0
information bus: scsi@2:0.0.0
nom logique: /dev/sdb
version: 01.0
numéro de série: WD-WMC3F0F60MPV
taille: 931GiB (1TB)
fonctionnalités: partitioned partitioned:dos
configuration: ansiversion=5 sectorsize=4096 signature=0003afc3
*-volume:0
description: Linux swap volume
identifiant matériel: 1
information bus: scsi@2:0.0.0,1
nom logique: /dev/sdb1
version: 1
numéro de série: ce704e25-867f-4feb-9cc9-6bbadbaea35f
taille: 2050MiB
capacité: 2050MiB
fonctionnalités: primary nofs swap initialized
configuration: filesystem=swap pagesize=4096
*-volume:1
description: Volume EXT4
fabriquant: Linux
identifiant matériel: 2
information bus: scsi@2:0.0.0,2
nom logique: /dev/sdb2
nom logique: /donnees
version: 1.0
numéro de série: e6479648-6acc-4f81-bc65-38dc4ba0f0d6
taille: 929GiB
capacité: 929GiB
fonctionnalités: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized
configuration: created=2015-03-03 20:45:51 filesystem=ext4 label=donnees lastmountpoint=/donnees modified=2015-06-24 22:04:42 mount.fstype=ext4 mount.options=rw,relatime,data=ordered mounted=2015-06-24 22:04:42 state=mounted
*-scsi:2
identifiant matériel: 3
nom logique: scsi5
fonctionnalités: emulated
*-cdrom
description: DVD writer
produit: DVDRW SOHW-1633S
fabriquant: LITE-ON
identifiant matériel: 0.0.0
information bus: scsi@5:0.0.0
nom logique: /dev/cdrom
nom logique: /dev/sr0
version: B9S5
fonctionnalités: removable audio cd-r cd-rw dvd dvd-r
configuration: ansiversion=5 status=nodisc
*-scsi:3
identifiant matériel: 5
information bus: usb@2:4
nom logique: scsi6
fonctionnalités: emulated scsi-host
configuration: driver=usb-storage
*-disk:0
description: SCSI Disk
identifiant matériel: 0.0.0
information bus: scsi@6:0.0.0
nom logique: /dev/sdc
configuration: sectorsize=512
*-disk:1
description: SCSI Disk
identifiant matériel: 0.0.1
information bus: scsi@6:0.0.1
nom logique: /dev/sdd
configuration: sectorsize=512
*-disk:2
description: SCSI Disk
identifiant matériel: 0.0.2
information bus: scsi@6:0.0.2
nom logique: /dev/sde
configuration: sectorsize=512
*-disk:3
description: SCSI Disk
identifiant matériel: 0.0.3
information bus: scsi@6:0.0.3
nom logique: /dev/sdf
configuration: sectorsize=512
s@xubuntu:~$ s@xubuntu:~$ sudo parted -l
Modèle: ATA KINGSTON SV300S3 (scsi)
Disque /dev/sda : 120GB
Taille des secteurs (logiques/physiques): 512B/512B
Table de partitions : msdos
Numéro Début Fin Taille Type Système de fichiers Fanions
1 1049kB 118GB 118GB primary ext4 démarrage
2 118GB 120GB 2144MB extended
5 118GB 120GB 2144MB logical linux-swap(v1)
Modèle: ATA WDC WD10EZEX-08M (scsi)
Disque /dev/sdb : 1000GB
Taille des secteurs (logiques/physiques): 512B/4096B
Table de partitions : msdos
Numéro Début Fin Taille Type Système de fichiers Fanions
1 1049kB 2151MB 2150MB primary linux-swap(v1)
2 2151MB 1000GB 998GB primary ext4
s@xubuntu:~$ Dernière précision : Pas d'erreur au memtest.
N'hésitez pas à me demander toute autre log si nécessaire.
Merci d'avance !
(je vais allumer des cierges 
)
Dernière modification par fgi (Le 06/07/2015, à 21:22)
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#2 Le 27/06/2015, à 23:53
- fgi
Re : [Résolu][1404]Soft lockup au boot
Bonsoir à tous,
N'ayant pas trouvé de pistes de mon coté, je relance le sujet ... Quel bonne âme experte en configuration graphique peut m'aider ?
Merci !!
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#3 Le 28/06/2015, à 00:03
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Ici : http://ubuntuforums.org/showthread.php?t=2205211
La personne a résolu son problème en changeant l'alimentation.
Hors ligne
#4 Le 28/06/2015, à 00:41
- fgi
Re : [Résolu][1404]Soft lockup au boot
Je te remercie.
J'ai installé sensors, voici ce que cela donne. Est-ce que ça semble correspondre à une alim trop faible ?
s@xubuntu:~$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +43.0°C
dme1737-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0b00
5VSB: +2.54 V (min = +0.00 V, max = +6.64 V)
Vcore: +1.38 V (min = +0.00 V, max = +2.99 V)
+3.3V: +3.30 V (min = +0.00 V, max = +4.38 V)
+5V: +5.06 V (min = +0.00 V, max = +6.64 V)
+12V: +11.97 V (min = +0.00 V, max = +15.94 V)
3VSB: +3.25 V (min = +0.00 V, max = +4.38 V)
Vbat: +2.95 V (min = +0.00 V, max = +4.38 V)
fan1: 2416 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
temp1: +56.8°C (low = -127.0°C, high = +127.0°C)
SIO Temp: +39.6°C (low = -127.0°C, high = +127.0°C)
temp3: +39.5°C (low = -127.0°C, high = +127.0°C)
cpu0_vid: +1.550 V
s@xubuntu:~$Je ne sais pas à quoi ça correspond, mais ligne suivante semble faible ... si "5VSB" correspond à une sortie 5V ...
5VSB: +2.54 V (min = +0.00 V, max = +6.64 V)
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#5 Le 28/06/2015, à 15:15
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Je ne suis pas spécialiste des alimentations, mais la valeur pour le 5VSB est bien basse. Tu utilises quoi comme alim ? Une vieille bouse Advance à 20 euros ?
Hors ligne
#6 Le 28/06/2015, à 18:12
- fgi
Re : [Résolu][1404]Soft lockup au boot
L'alim d'origine de mon Packard Bell ...
Je viens de passer commande d'une Corsair VS450, ça ne peut pas faire de mal ...
Après avoir regardé sur la toile ce qu'est la 5VSB, je ne vois pas en quoi elle expliquerait mon problème, mais bon, remettre une alim neuve ne peut pas faire de mal, surtout que j'ai changé mes disques il y a quelques semaine, donc mon alim vieillissante peut peiner ....
On en reparle dans quelques jours 
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#7 Le 29/06/2015, à 21:05
- fgi
Re : [Résolu][1404]Soft lockup au boot
Bonsoir,
j'ai changé mon alim ... pas d'amélioration 
Voici le retour de sensors:
s@xubuntu:~$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +44.0°C
dme1737-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0b00
5VSB: +2.54 V (min = +4.50 V, max = +5.50 V) ALARM
Vcore: +1.38 V (min = +0.00 V, max = +2.99 V)
+3.3V: +3.32 V (min = +2.97 V, max = +3.63 V)
+5V: +5.04 V (min = +4.50 V, max = +5.50 V)
+12V: +11.96 V (min = +10.81 V, max = +13.19 V)
3VSB: +3.28 V (min = +2.97 V, max = +3.63 V)
Vbat: +2.94 V (min = +2.70 V, max = +3.30 V)
fan1: 3119 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
temp1: +61.0°C (low = -127.0°C, high = +127.0°C)
SIO Temp: +34.4°C (low = -127.0°C, high = +127.0°C)
temp3: +31.5°C (low = -127.0°C, high = +127.0°C)
cpu0_vid: +1.550 V
s@xubuntu:~$ Et les copies d'écran du popup d'erreur :
Help !!!
Merci 
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#8 Le 29/06/2015, à 21:14
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Sur le forum de fedora (dernier message), le bug semble corrigé après mise à jour du kernel : http://forums.fedoraforum.org/showthread.php?t=300255
Dernière modification par linux4pas (Le 29/06/2015, à 21:26)
Hors ligne
#9 Le 29/06/2015, à 21:28
- fgi
Re : [Résolu][1404]Soft lockup au boot
Bien vu.
Mais comment expliquer que j'ai le pb avec ma live-usb, et avec tous les kernels précédents ?
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#10 Le 29/06/2015, à 21:46
- fgi
Re : [Résolu][1404]Soft lockup au boot
Scoop : il semblerait que le pb ait disparu,au détour de mes multiples reboots... et ce, quelque soit le kernel utilisé.
L'explication que j'y vois c'est que mon alim ait été trop faible, et que ma nouvelle alim ait rechargé la pile de la carte mère, ce qui explique qu'il lui ait fallu un peu de temps.
Pour valider mon hypothèse, je vais laisser mon PC à l'arrêt pour la nuit, et je vais refaire un test demain. On verra ...
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#11 Le 29/06/2015, à 21:50
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
fgi a écrit :
Bien vu.
Mais comment expliquer que j'ai le pb avec ma live-usb, et avec tous les kernels précédents ?
Je ne sais pas quelle est la version du kernel sur les live cd/usb (normalement pas la dernière), mais le bug n'a été corrigé qu'à partir de la version 3.18. Il faut croire que cela ne concerne que certaines marques ou composants, car je n'ai jamais rencontré ce problème.
J'attends ta confirmation demain. Dans tous les cas, tu n'auras pas acheté une nouvelle alim pour rien.
Hors ligne
#12 Le 30/06/2015, à 20:00
- fgi
Re : [Résolu][1404]Soft lockup au boot
Bon, bein c'est pas probant ....
Ce matin : gel au boot sur le splash screen.
Depuis, le boot se déroule sans gel mais j'ai toujours les popup d'erreur ci-dessus à l'ouverture de session ...
Bref, ça ne va pas mieux :'(
Je ne pense pas que ce soit le bug du kernel : je ne l'ai jamais eu précédemment.
J'aurai besoin d'aide pour fouiller les logs de l'interface graphique xubuntu : j'ai l'impression que c'est par là que ça se passe ...
Dernière modification par fgi (Le 30/06/2015, à 20:00)
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#13 Le 30/06/2015, à 20:34
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Ca n'a sûrement rien à voir, mais pourquoi utilises-tu xubuntu i386 ? Tu as tenté le test avec une live iso 64 bits ? Et pour ne pas complètement écarter la piste du kernel, tu peux essayer de lancer un livecd d'Ubuntu/Xubuntu 15.04 avec son noyau 3.19 (censé corriger le bug).
Dans un des liens mentionnés plus haut, un type a carrément viré sa carte graphique pour contourner le problème. Mais c'est une option que tu n'as pas, sauf si ta carte mère dispose d'un chipset graphique intégré.
Dernière modification par linux4pas (Le 30/06/2015, à 21:20)
Hors ligne
#14 Le 30/06/2015, à 22:13
- fgi
Re : [Résolu][1404]Soft lockup au boot
linux4pas a écrit :
Ca n'a sûrement rien à voir, mais pourquoi utilises-tu xubuntu i386 ? Tu as tenté le test avec une live iso 64 bits ?
J'ai suivi le conseil de moko ici , au #16
Et pour ne pas complètement écarter la piste du kernel, tu peux essayer de lancer un livecd d'Ubuntu/Xubuntu 15.04 avec son noyau 3.19 (censé corriger le bug).
Bonne suggestion, je vais me préparer un live 15.04 pour jouer dès demain
Dans un des liens mentionnés plus haut, un type a carrément viré sa carte graphique pour contourner le problème. Mais c'est une option que tu n'as pas, sauf si ta carte mère dispose d'un chipset graphique intégré.
Ah oui, mais là je n'ai pas cette option ... et si j'en viens à changer de carte graphique, eh ben ... je changerai sûrement ma carte mère au passage, comme ça j'aurai une PC tout neuf ;-)
Je m'interroge aussi sur le fait que mes pb soient arrivé avec les hausses de températures ... mon PC a peut-être un pb hard qui s'est réveillé avec la chaleur ... je dis ça parce que mon alim toute neuve souffle comme un boeuf ... il a quand même fait 37° cet aprem ....
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#15 Le 30/06/2015, à 22:35
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
En parlant de température, tu as une idée du composant qui affiche cette valeur ?
temp1: +61.0°C (low = -127.0°C, high = +127.0°C)Histoire de ne pas trop nous éparpiller, j'attends que tu fasses le test avec Xubuntu 15.04. C'est tout de même bizarre que tu aies réussi momentanément à te débarrasser du problème. Peut-être faisait-il -2° dans la pièce...
Hors ligne
#16 Le 01/07/2015, à 21:49
- fgi
Re : [Résolu][1404]Soft lockup au boot
Bon, petit bilan ...
D'abord, les températures sont redescendues de 10° ... résultat, mon alim est ultra-silencieuse 
Un coup d'oeil sur sensors :
s@xubuntu:~$ sensors
dme1737-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0b00
5VSB: +2.53 V (min = +4.50 V, max = +5.50 V) ALARM
Vcore: +1.07 V (min = +0.00 V, max = +2.99 V)
+3.3V: +3.31 V (min = +2.97 V, max = +3.63 V)
+5V: +5.02 V (min = +4.50 V, max = +5.50 V)
+12V: +11.96 V (min = +10.81 V, max = +13.19 V)
3VSB: +3.28 V (min = +2.97 V, max = +3.63 V)
Vbat: +2.94 V (min = +2.70 V, max = +3.30 V)
fan1: 1900 RPM (min = 0 RPM)
fan2: 0 RPM (min = 0 RPM)
fan4: 0 RPM (min = 0 RPM)
temp1: +44.6°C (low = -127.0°C, high = +127.0°C)
SIO Temp: +26.7°C (low = -127.0°C, high = +127.0°C)
temp3: +23.8°C (low = -127.0°C, high = +127.0°C)
cpu0_vid: +1.550 V
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +29.0°C Là aussi, ça va mieux ...
Boot 14.04 : Aucun pb sur la séquence de démarrage, par contre, j'ai toujours les popups à l'ouverture de session (cf mes copies d'écran au post #7.
Live 15.02 : Il y a eu un problème sur la génération de la clé USB. Il faut que je regarde si il y a quelque chose là dessus sur le forum....
Donc à ce stade, je reste (faute de mieux) sur mon hypothèse d'un composant qui a souffert de la chaleur, probablement en lien avec la carte graphique ...
J'aimerai fouiller les logs de l'IHM pour comprendre le popup d'erreur, peut-être que ça expliquera le reste ... pour cela aussi, je vais faire un tour dans la section adhoc ...
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#17 Le 01/07/2015, à 22:42
- fgi
Re : [Résolu][1404]Soft lockup au boot
Juste pour préciser que le pb de génération de la live-usb 15.02 est résolu ici.
Cela dit, une fois démarré, mon PC n'arrive à rien .... l'interface graphique doit être trop lourde, c'est pour cela que je suis passé en xubuntu ... mais au moins, je n'ai pas de message d'erreur.
Sinon, j'ai posté mon pb dans la section Graphique du forum, on verra bien si quelqu'un se penche dessus
Dernière modification par fgi (Le 01/07/2015, à 22:43)
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#18 Le 01/07/2015, à 23:05
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Pourquoi ne pas avoir testé avec Xubuntu 15.04 ? Je mets le 04 en gras car tu n'arrêtes pas de parler d'Ubuntu 15.02.
Sur l'autre topic, je laisse la main à un autre, en espèrant que tu auras plus de chance ce coup-ci. Je garde quand même un oeil sur ton cas. La résolution de ton problème m'intrigue pas mal.
Hors ligne
#19 Le 03/07/2015, à 22:48
- fgi
Re : [Résolu][1404]Soft lockup au boot
linux4pas a écrit :
Pourquoi ne pas avoir testé avec Xubuntu 15.04 ?
Argl... Tu me mets le doute... Je vais regarder pendant le we (je suis un peu débordé, là...)
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#20 Le 04/07/2015, à 21:54
- fgi
Re : [Résolu][1404]Soft lockup au boot
Pour la nouvelle version, tu as raison, j'ai bien pris une 15.04. Je ne sais pas pourquoi j'ai marqué 15.02 .... au temps pour moi !!
Quant à l'autre post, le moins qu'on puisse dire, c'est qu'il ne passionne pas les foules
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#21 Le 06/07/2015, à 21:22
- fgi
Re : [Résolu][1404]Soft lockup au boot
@linux4pas : ça y est, le pb est résolu ... une histoire de config de driver écrasée par ma dernière maj de kernel. Je te laisse voir les détails dans le post
En tout cas, merci de t'être penché sur mon cas
A+
L'homme ne recherche pas La Vérité. Il n'est qu'avide de certitude ... [Cornélius Castoriadis]
~ Ubuntu 22.04 64 bits ~
Hors ligne
#22 Le 07/07/2015, à 00:19
- linux4pas
Re : [Résolu][1404]Soft lockup au boot
Content que tu aies trouvé la solution. Espérons ne plus jamais retomber sur ce problème qui existe depuis tant d'années.
Hors ligne