Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 28/08/2015, à 12:55

Pingouinbricoleur

[Résolu] Sata COMRESET failed (errno=-32)

Bonjour à tous,

Je poste ici car apparemment les serveurs linuxmint sont défaillants en ce moment.
Ils réclament un mot de passe même sur la page d'accueil : bizarre !
Pour ceux qui voudraient vérifier : http://www.linuxmint-fr.org/

Ma config : linuxmint 17 Mate 64 b
Tour : carte mère asus M3A
Au moment de l'installation de linuxmint 17, j'ai indiqué sda6 pour /home et sda7 pour /

2 disques durs sata dont 1 assez vieux.

Dans le bios du pc, en affichant les infos, il me dit que les 2 disques durs sont OK.

Si je lance gparted, il ne m'affiche que le premier disque dont je me sers : sda.
Le second, je l'ai monté après l'installation de la linuxmint 17. Il est en attente car mon premier disque est bientôt plein.

Symptômes :
1) Quelquefois, au démarrage du pc, il cherche et peine à la détection du second disque sata
2) quelquefois la souris principale (sans fil) branchée sur un port usb ne fonctionne pas dès l'arrivée sur le bureau. Je suis obligé de redémarrer pour qu'elle veuille bien fonctionner.
Pour éviter de redémarrer sauvagement le pc, j'ai donc ajouté et branché une vieille souris à roulette toujours sur un port usb. Je précise que la vieille souris ne se bloque jamais.

Existe-t-il des commandes pour vérifier le matériel par exemple : une commande à taper dans un terminal quand la souris se bloque ?
Est-ce normal que gparted n'affiche que le disque pris en compte lors de l'installation ?

Je soupçonne la carte mère d'avoir des défaillances au niveau ports sata et au niveau des ports usb.

Merci d'avance de vos réponses.

Cdt,

Dernière modification par Pingouinbricoleur (Le 31/08/2015, à 20:48)

Hors ligne

#2 Le 28/08/2015, à 15:40

pingouinux

Re : [Résolu] Sata COMRESET failed (errno=-32)

Bonjour,

Ils réclament un mot de passe même sur la page d'accueil : bizarre !

J'ai essayé : le site demande effectivement un mot de passe, mais il précise qu'il est en maintenance.

Dernière modification par pingouinux (Le 28/08/2015, à 15:42)

Hors ligne

#3 Le 28/08/2015, à 17:01

cqfd93

Re : [Résolu] Sata COMRESET failed (errno=-32)

Bonjour,

Pingouinbricoleur a écrit :

Je poste ici car apparemment les serveurs linuxmint sont défaillants en ce moment.
Ils réclament un mot de passe même sur la page d'accueil : bizarre !
Pour ceux qui voudraient vérifier : http://www.linuxmint-fr.org/

Ça fait un bout de temps qu'il est dans les choux, mais il y a un nouveau forum.


cqfd93

En ligne

#4 Le 28/08/2015, à 17:07

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Ok. Merci de ta réponse pour le nouveau forum.

Sinon, voici mon etc/fstab :

# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
# / was on /dev/sda7 during installation
UUID=2a72443c-9f2b-4cd8-8369-60adf2b10462 /               ext4    errors=remount-ro 0       1
# /home was on /dev/sda6 during installation
UUID=0a352f0a-e413-4a17-b025-27d057f52a76 /home           ext4    defaults        0       2
# swap was on /dev/sda5 during installation
UUID=894e667b-5d86-4cf5-8e4e-16a0cb1567ac none            swap    sw              0       0
/dev/fd0        /media/floppy0  auto    rw,user,noauto,exec,utf8 0       0
192.168.0.8:/volume1/save /media/diskstation_save nfs rw 0 0

Je n'ai plus de lecteur de disquette : l'avant dernière ligne est peut-être à supprimer mais de toute façon, ce n'est pas cette ligne la cause de mon problème.

et quand je lance gparted dans une console, il y a plein de lignes comportant une erreur qui s'affichent comme celles-ci :

(gpartedbin:5406): GLib-CRITICAL **: Source ID 7 was not found when attempting to remove it
(gpartedbin:5406): GLib-CRITICAL **: Source ID 6 was not found when attempting to remove it
(gpartedbin:5406): GLib-CRITICAL **: Source ID 26 was not found when attempting to remove it
(gpartedbin:5406): GLib-CRITICAL **: Source ID 25 was not found when attempting to remove it
(gpartedbin:5406): GLib-CRITICAL **: Source ID 35 was not found when attempting to remove it

C'est peut-être une piste ?


Modération : merci à l'avenir d'utiliser les balises code (explications ici).

Dernière modification par cqfd93 (Le 28/08/2015, à 18:25)

Hors ligne

#5 Le 28/08/2015, à 18:11

Skubu

Re : [Résolu] Sata COMRESET failed (errno=-32)

Salut,

Pour l'état de santé des disques dur, il y a smartmontools.

sudo apt-get install smartmontools

Si sda correspond à ton 1er disque et sdb au 2nd tapes :

sudo smartctl -a /dev/sda
sudo smartctl -a /dev/sdb

et retournes ici les résultats.



Concernant la souris sans fil, le fait-elle aussi sur un autre PC ?


Debian / Archlinux | Gnome / KDE

Hors ligne

#6 Le 28/08/2015, à 18:30

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Voici les résultats des 2 commandes :

sudo smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint F1 DT
Device Model:     SAMSUNG HD502IJ
Serial Number:    S1PZJDWQ900571
LU WWN Device Id: 5 0000f0 003095017
Firmware Version: 1AA01113
User Capacity:    500 107 862 016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is:    Fri Aug 28 19:20:09 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 7016) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 118) minutes.
Conveyance self-test routine
recommended polling time: 	 (  13) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   085   085   011    Pre-fail  Always       -       5290
  4 Start_Stop_Count        0x0032   096   096   000    Old_age   Always       -       4259
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   100   051    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0025   100   100   015    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       14779
 10 Spin_Retry_Count        0x0033   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0012   100   100   000    Old_age   Always       -       1
 12 Power_Cycle_Count       0x0032   096   096   000    Old_age   Always       -       4247
 13 Read_Soft_Error_Rate    0x000e   100   100   000    Old_age   Always       -       0
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0033   026   026   000    Pre-fail  Always       -       74
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   072   054   000    Old_age   Always       -       28 (Min/Max 16/28)
194 Temperature_Celsius     0x0022   071   052   000    Old_age   Always       -       29 (Min/Max 16/31)
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       60550
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   100   100   000    Old_age   Always       -       6
200 Multi_Zone_Error_Rate   0x000a   100   099   000    Old_age   Always       -       2
201 Soft_Read_Error_Rate    0x000a   253   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

et pour le disque sdb :

smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/sdb: Unknown USB bridge [0x0bda:0x0151 (0x5195)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

Le résultat du second est un peu surprenant car c'est un sata et non un usb.

Quant à la souris, je n'utilise qu'un seul pc. Le second que j'ai, sert pour mes petits enfants quand ils viennent et donc, de plus, la panne étant aléatoire, il me faudrait pratiquement 1 an pour tester.
De plus, il plante : la config est sans doute trop faible pour utiliser.

Hors ligne

#7 Le 28/08/2015, à 21:35

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

sdb : si c'est lecteur de cartes interne, il est effectivement branché en usb.Et le 2nd HD est alors en sdc ou sdd...

sudo fdisk -l
sudo parted -l
sudo blkid

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#8 Le 28/08/2015, à 21:45

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Non, sdb est un disque dur Sata interne 3,5 " de 120 Go si ma mémoire est bonne.

Par contre, j'ai un lecteur de cartes flash interne branché sur un port usb.

sudo fdisk -l donne ceci :

Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 têtes, 63 secteurs/piste, 60801 cylindres, total 976773168 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Identifiant de disque : 0x0b990b99

Périphérique Amorçage  Début         Fin      Blocs    Id. Système
/dev/sda1   *          63    81915434    40957686    7  HPFS/NTFS/exFAT
/dev/sda2        81915435   165758669    41921617+   7  HPFS/NTFS/exFAT
/dev/sda3       165758731   976768368   405504819    5  Étendue
/dev/sda5       165758733   178048394     6144831   82  partition d'échange Linux / Solaris
/dev/sda6       178048458   933633539   377792541   83  Linux
/dev/sda7       933633603   976768368    21567383   83  Linux

Disk /dev/sdf: 163.9 GB, 163928604672 bytes
255 têtes, 63 secteurs/piste, 19929 cylindres, total 320173056 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Identifiant de disque : 0x24892488

Périphérique Amorçage  Début         Fin      Blocs    Id. Système
/dev/sdf1   *          63    61474815    30737376+   7  HPFS/NTFS/exFAT
/dev/sdf2        61474816   176814079    57669632    7  HPFS/NTFS/exFAT
/dev/sdf3       176816126   320172031    71677953    5  Étendue
/dev/sdf5       176816128   288407924    55795898+  83  Linux
/dev/sdf6       317030400   320172031     1570816   82  partition d'échange Linux / Solaris
/dev/sdf7       288409600   317026303    14308352   83  Linux

Les entrées de la table de partitions ne sont pas dans l'ordre du disque

sudo parted -l donne ceci :

Modèle: ATA SAMSUNG HD502IJ (scsi)
Disque /dev/sda : 500GB
Taille des secteurs (logiques/physiques): 512B/512B
Table de partitions : msdos

Numéro  Début   Fin     Taille  Type      Système de fichiers  Fanions
 1      32,3kB  41,9GB  41,9GB  primary   ntfs                 démarrage
 2      41,9GB  84,9GB  42,9GB  primary   ntfs
 3      84,9GB  500GB   415GB   extended
 5      84,9GB  91,2GB  6292MB  logical   linux-swap(v1)
 6      91,2GB  478GB   387GB   logical   ext4
 7      478GB   500GB   22,1GB  logical   ext4

Modèle: ATA Maxtor 6B160M0 (scsi)
Disque /dev/sdf : 164GB
Taille des secteurs (logiques/physiques): 512B/512B
Table de partitions : msdos

Numéro  Début   Fin     Taille  Type      Système de fichiers  Fanions
 1      32,3kB  31,5GB  31,5GB  primary   ntfs                 démarrage
 2      31,5GB  90,5GB  59,1GB  primary   ntfs
 3      90,5GB  164GB   73,4GB  extended
 5      90,5GB  148GB   57,1GB  logical   ext4
 7      148GB   162GB   14,7GB  logical   ext4
 6      162GB   164GB   1609MB  logical   linux-swap(v1)

sudo blkid donne ceci :

/dev/sda1: LABEL="XP" UUID="92CC7D0CCC7CEBBB" TYPE="ntfs" 
/dev/sda2: LABEL="DONNEES" UUID="403CB35D3CB34D22" TYPE="ntfs" 
/dev/sda5: UUID="894e667b-5d86-4cf5-8e4e-16a0cb1567ac" TYPE="swap" 
/dev/sda6: UUID="0a352f0a-e413-4a17-b025-27d057f52a76" TYPE="ext4" 
/dev/sda7: UUID="2a72443c-9f2b-4cd8-8369-60adf2b10462" TYPE="ext4" 
/dev/sdf1: UUID="3EE45B10E45AC9B3" TYPE="ntfs" 
/dev/sdf2: UUID="6362AEDE536D0C8A" TYPE="ntfs" 
/dev/sdf5: UUID="b0a8b71b-83e3-45b7-a90f-84c9c54a0efa" TYPE="ext4" 
/dev/sdf6: UUID="a5fbf08b-88e9-4ee8-a0c7-c98a9ab05617" TYPE="swap" 
/dev/sdf7: UUID="a0d174a5-7232-4eee-b0d3-bfbfb0c29910" TYPE="ext4" 

merci de vos réponses.
smile

Hors ligne

#9 Le 28/08/2015, à 21:52

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

Disk /dev/sdf: 163.9 GB, 163928604672 bytes

Bingo ! Donc

sudo smartctl -a /dev/sdf

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#10 Le 29/08/2015, à 09:27

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

La commande donne ceci :

smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/sdf: Unknown USB bridge [0x0bda:0x0151 (0x5195)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

Il parle encore d'usb !

Hors ligne

#11 Le 29/08/2015, à 11:36

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

Relis Retour utilisable de commande puis applique-le, merci.


%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#12 Le 29/08/2015, à 12:28

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Je redonne les résultats de la console.

toto@AsusET:~$
sudo smartctl -a /dev/sdf
[sudo] password for toto: 
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/sdf: Unknown USB bridge [0x0bda:0x0151 (0x5195)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary
toto@AsusET:~$ 

C'est la même réponse.

Hors ligne

#13 Le 29/08/2015, à 12:42

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

OK. -On met le retour en une seule fenêtre :

toto@AsusET:~$ sudo smartctl -a /dev/sdf
...
toto@AsusET:~$

Alors découvrons pourquoi sdf est vu en usb :

lsusb
sudo lshw

Autre question : pourquoi as-tu le noyau 3.13.0-24 ? Tu ne fais jamais de mise à jour ???


%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#14 Le 29/08/2015, à 17:09

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Voici le résultat de lsusb :

toto@AsusET:~$ lsusb
Bus 001 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader)
Bus 001 Device 003: ID 046d:0826 Logitech, Inc. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 045e:00e1 Microsoft Corp. Wireless Laser Mouse 6000 Reciever
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
toto@AsusET:~$ 

sinon, pour répondre à ta question des mises à jour, je les fais dès que le petit écusson n'est plus vert.
Et si je fais actualiser dans la fenêtre des mises à jour, il me dit ok.

Pour info :
En usb, il y a 2 souris (1 filaire et 1 sans fil), 1 lecteur de cartes flash et l'imprimante qui n'est pas allumée tant que je n'imprime pas (comme j'imprime peu, elles reste très souvent éteinte).

Hors ligne

#15 Le 29/08/2015, à 18:22

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

Donne

uname -a

et le retour complet de

sudo apt-get update

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#16 Le 29/08/2015, à 18:35

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

toto@AsusET:~$ uname -a
Linux AsusET 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
toto@AsusET:~$ 

et la suite :

toto@AsusET:~$ sudo apt-get update
[sudo] password for toto: 
Ign http://archive.canonical.com trusty InRelease                              
Ign http://archive.ubuntu.com trusty InRelease                                 
Ign http://security.ubuntu.com trusty-security InRelease                       
Ign http://packages.linuxmint.com qiana InRelease                              
Atteint http://archive.canonical.com trusty Release.gpg                        
Ign http://extra.linuxmint.com qiana InRelease                                 
Ign http://archive.ubuntu.com trusty-updates InRelease                         
Atteint http://archive.canonical.com trusty Release                            
Atteint http://security.ubuntu.com trusty-security Release.gpg                 
Atteint http://archive.ubuntu.com trusty Release.gpg                           
Réception de : 1 http://extra.linuxmint.com qiana Release.gpg [198 B]          
Atteint http://archive.canonical.com trusty/partner amd64 Packages             
Réception de : 2 http://packages.linuxmint.com qiana Release.gpg [198 B]       
Atteint http://security.ubuntu.com trusty-security Release                     
Atteint http://archive.canonical.com trusty/partner i386 Packages              
Atteint http://archive.ubuntu.com trusty-updates Release.gpg                   
Réception de : 3 http://extra.linuxmint.com qiana Release [3 204 B]            
Atteint http://archive.canonical.com trusty/partner Translation-en             
Atteint http://security.ubuntu.com trusty-security/main amd64 Packages         
Réception de : 4 http://packages.linuxmint.com qiana Release [24,2 kB]         
Atteint http://archive.ubuntu.com trusty Release                               
Atteint http://security.ubuntu.com trusty-security/restricted amd64 Packages   
Réception de : 5 http://extra.linuxmint.com qiana/main amd64 Packages [8 070 B]
Atteint http://archive.ubuntu.com trusty-updates Release                       
Atteint http://security.ubuntu.com trusty-security/universe amd64 Packages     
Réception de : 6 http://extra.linuxmint.com qiana/main i386 Packages [8 049 B] 
Réception de : 7 http://packages.linuxmint.com qiana/main amd64 Packages [31,0 kB]
Atteint http://archive.ubuntu.com trusty/main amd64 Packages                   
Atteint http://security.ubuntu.com trusty-security/multiverse amd64 Packages   
Atteint http://archive.ubuntu.com trusty/restricted amd64 Packages             
Atteint http://security.ubuntu.com trusty-security/main i386 Packages          
Atteint http://archive.ubuntu.com trusty/universe amd64 Packages               
Atteint http://security.ubuntu.com trusty-security/restricted i386 Packages    
Réception de : 8 http://packages.linuxmint.com qiana/upstream amd64 Packages [24,2 kB]
Atteint http://archive.ubuntu.com trusty/multiverse amd64 Packages             
Atteint http://security.ubuntu.com trusty-security/universe i386 Packages      
Atteint http://archive.ubuntu.com trusty/main i386 Packages                    
Atteint http://security.ubuntu.com trusty-security/multiverse i386 Packages    
Ign http://ppa.launchpad.net trusty InRelease                                  
Ign http://ppa.launchpad.net trusty InRelease                                  
Atteint http://archive.ubuntu.com trusty/restricted i386 Packages              
Atteint http://security.ubuntu.com trusty-security/main Translation-en         
Ign http://ppa.launchpad.net trusty InRelease                                  
Atteint http://archive.ubuntu.com trusty/universe i386 Packages                
Atteint http://security.ubuntu.com trusty-security/multiverse Translation-en   
Ign http://ppa.launchpad.net trusty InRelease                                  
Atteint http://archive.ubuntu.com trusty/multiverse i386 Packages              
Atteint http://security.ubuntu.com trusty-security/restricted Translation-en   
Atteint http://ppa.launchpad.net trusty Release.gpg                            
Atteint http://ppa.launchpad.net trusty Release.gpg                            
Atteint http://security.ubuntu.com trusty-security/universe Translation-en     
Atteint http://ppa.launchpad.net trusty Release.gpg                            
Atteint http://ppa.launchpad.net trusty Release.gpg                            
Atteint http://archive.ubuntu.com trusty/main Translation-fr                   
Réception de : 9 http://packages.linuxmint.com qiana/import amd64 Packages [32,5 kB]
Atteint http://ppa.launchpad.net trusty Release                                
Atteint http://archive.ubuntu.com trusty/main Translation-en                   
Atteint http://ppa.launchpad.net trusty Release                                
Atteint http://ppa.launchpad.net trusty Release                                
Atteint http://archive.ubuntu.com trusty/multiverse Translation-fr             
Atteint http://ppa.launchpad.net trusty Release                                
Atteint http://ppa.launchpad.net trusty/main Sources                           
Atteint http://ppa.launchpad.net trusty/main amd64 Packages                    
Atteint http://archive.ubuntu.com trusty/multiverse Translation-en             
Atteint http://ppa.launchpad.net trusty/main i386 Packages                     
Ign http://extra.linuxmint.com qiana/main Translation-fr_FR                    
Atteint http://archive.ubuntu.com trusty/restricted Translation-fr             
Atteint http://archive.ubuntu.com trusty/restricted Translation-en             
Réception de : 10 http://packages.linuxmint.com qiana/main i386 Packages [30,4 kB]
Ign http://extra.linuxmint.com qiana/main Translation-fr                       
Atteint http://ppa.launchpad.net trusty/main Sources                           
Ign http://extra.linuxmint.com qiana/main Translation-en                       
Atteint http://archive.ubuntu.com trusty/universe Translation-fr               
Atteint http://ppa.launchpad.net trusty/main amd64 Packages                    
Atteint http://archive.ubuntu.com trusty/universe Translation-en               
Atteint http://ppa.launchpad.net trusty/main i386 Packages                     
Atteint http://archive.ubuntu.com trusty-updates/main amd64 Packages           
Atteint http://ppa.launchpad.net trusty/main Translation-en                    
Atteint http://ppa.launchpad.net trusty/main Sources                           
Atteint http://archive.ubuntu.com trusty-updates/restricted amd64 Packages     
Atteint http://ppa.launchpad.net trusty/main amd64 Packages                    
Atteint http://ppa.launchpad.net trusty/main i386 Packages                     
Atteint http://archive.ubuntu.com trusty-updates/universe amd64 Packages       
Atteint http://archive.ubuntu.com trusty-updates/multiverse amd64 Packages     
Atteint http://archive.ubuntu.com trusty-updates/main i386 Packages            
Atteint http://archive.ubuntu.com trusty-updates/restricted i386 Packages      
Atteint http://ppa.launchpad.net trusty/main Sources                           
Atteint http://archive.ubuntu.com trusty-updates/universe i386 Packages        
Atteint http://ppa.launchpad.net trusty/main amd64 Packages                    
Atteint http://archive.ubuntu.com trusty-updates/multiverse i386 Packages      
Atteint http://ppa.launchpad.net trusty/main i386 Packages                     
Atteint http://archive.ubuntu.com trusty-updates/main Translation-en           
Atteint http://ppa.launchpad.net trusty/main Translation-en                    
Atteint http://archive.ubuntu.com trusty-updates/multiverse Translation-en     
Réception de : 11 http://packages.linuxmint.com qiana/upstream i386 Packages [24,2 kB]
Atteint http://archive.ubuntu.com trusty-updates/restricted Translation-en     
Atteint http://archive.ubuntu.com trusty-updates/universe Translation-en       
Réception de : 12 http://packages.linuxmint.com qiana/import i386 Packages [32,5 kB]
Ign http://archive.ubuntu.com trusty/main Translation-fr_FR                    
Ign http://archive.ubuntu.com trusty/multiverse Translation-fr_FR              
Ign http://archive.ubuntu.com trusty/restricted Translation-fr_FR              
Ign http://ppa.launchpad.net trusty/main Translation-fr_FR              
Ign http://archive.ubuntu.com trusty/universe Translation-fr_FR         
Ign http://ppa.launchpad.net trusty/main Translation-fr                 
Ign http://ppa.launchpad.net trusty/main Translation-en                        
Ign http://ppa.launchpad.net trusty/main Translation-fr_FR                     
Ign http://ppa.launchpad.net trusty/main Translation-fr                        
Ign http://ppa.launchpad.net trusty/main Translation-en                        
Ign http://packages.linuxmint.com qiana/import Translation-fr_FR               
Ign http://packages.linuxmint.com qiana/import Translation-fr
Ign http://packages.linuxmint.com qiana/import Translation-en
Ign http://packages.linuxmint.com qiana/main Translation-fr_FR
Ign http://packages.linuxmint.com qiana/main Translation-fr
Ign http://packages.linuxmint.com qiana/main Translation-en
Ign http://packages.linuxmint.com qiana/upstream Translation-fr_FR
Ign http://packages.linuxmint.com qiana/upstream Translation-fr
Ign http://packages.linuxmint.com qiana/upstream Translation-en
219 ko réceptionnés en 38s (5 743 o/s)
Lecture des listes de paquets... Fait
toto@AsusET:~$ 

Hors ligne

#17 Le 29/08/2015, à 20:24

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

Bon : je ne vois pas d'erreur dans cet update de Qiana.
Donc étape suivante, cette simulation :

sudo apt-get -s dist-upgrade

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#18 Le 29/08/2015, à 20:33

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Voici le résultat :

toto@AsusET:~$ sudo apt-get -s dist-upgrade
[sudo] password for toto: 
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Calcul de la mise à jour... Fait
Le paquet suivant a été installé automatiquement et n'est plus nécessaire :
  gcc-4.8-base:i386
Veuillez utiliser « apt-get autoremove » pour le supprimer.
Les paquets suivants seront mis à jour :
  base-files gir1.2-gudev-1.0 grub-common grub-pc grub-pc-bin grub2-common
  libegl1-mesa libegl1-mesa-drivers libgbm1 libgl1-mesa-dri:i386
  libgl1-mesa-dri libgl1-mesa-glx libgl1-mesa-glx:i386 libglapi-mesa:i386
  libglapi-mesa libgles2-mesa libgudev-1.0-0 libgudev-1.0-0:i386
  libopenvg1-mesa libpam-systemd libsystemd-daemon0 libsystemd-login0 libudev1
  libudev1:i386 libwayland-egl1-mesa libxatracker2 systemd-services udev
  xserver-xorg-video-intel
29 mis à jour, 0 nouvellement installés, 0 à enlever et 0 non mis à jour.
Inst base-files [7.2ubuntu5.2] (7.2ubuntu5.3 Ubuntu:14.04/trusty-updates [amd64])
Conf base-files (7.2ubuntu5.3 Ubuntu:14.04/trusty-updates [amd64])
Inst udev [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libudev1 [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64]) [libudev1:amd64 on libudev1:i386] [libudev1:i386 on libudev1:amd64] [libudev1:i386 ]
Inst libudev1:i386 [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [i386])
Inst libpam-systemd [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64]) []
Inst systemd-services [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libsystemd-daemon0 [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Inst libsystemd-login0 [204-5ubuntu20.10] (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Inst libgl1-mesa-dri [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) [libgl1-mesa-dri:i386 on libgl1-mesa-dri:amd64] [libgl1-mesa-dri:amd64 on libgl1-mesa-dri:i386] [libgl1-mesa-dri:i386 ]
Inst libgl1-mesa-dri:i386 [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386])
Inst libgbm1 [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Inst libgl1-mesa-glx:i386 [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386]) [libgl1-mesa-glx:amd64 on libgl1-mesa-glx:i386] [libgl1-mesa-glx:i386 on libgl1-mesa-glx:amd64] [libgl1-mesa-glx:amd64 ]
Inst libgl1-mesa-glx [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libwayland-egl1-mesa [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) [libegl1-mesa-drivers:amd64 ]
Inst libegl1-mesa-drivers [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libgles2-mesa [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libglapi-mesa [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) [libglapi-mesa:i386 on libglapi-mesa:amd64] [libglapi-mesa:amd64 on libglapi-mesa:i386] [libglapi-mesa:i386 ]
Inst libglapi-mesa:i386 [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386]) []
Inst libopenvg1-mesa [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64]) []
Inst libegl1-mesa [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Inst libgudev-1.0-0 [1:204-5ubuntu20.10] (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64]) [libgudev-1.0-0:amd64 on libgudev-1.0-0:i386] [libgudev-1.0-0:i386 on libgudev-1.0-0:amd64] [libgudev-1.0-0:i386 ]
Inst libgudev-1.0-0:i386 [1:204-5ubuntu20.10] (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [i386])
Inst libxatracker2 [10.1.3-0ubuntu0.3] (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Inst gir1.2-gudev-1.0 [1:204-5ubuntu20.10] (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Inst grub-pc [2.02~beta2-9ubuntu1] (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64]) []
Inst grub-pc-bin [2.02~beta2-9ubuntu1] (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64]) []
Inst grub2-common [2.02~beta2-9ubuntu1] (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64]) []
Inst grub-common [2.02~beta2-9ubuntu1] (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64])
Inst xserver-xorg-video-intel [2:2.99.910-0ubuntu1.4] (2:2.99.910-0ubuntu1.6 Ubuntu:14.04/trusty-updates [amd64])
Conf libudev1 (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libudev1:i386 (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [i386])
Conf udev (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libsystemd-daemon0 (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf systemd-services (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libpam-systemd (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libsystemd-login0 (204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libgl1-mesa-dri:i386 (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386])
Conf libgl1-mesa-dri (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libgbm1 (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libglapi-mesa (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libglapi-mesa:i386 (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386])
Conf libgl1-mesa-glx (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libgl1-mesa-glx:i386 (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [i386])
Conf libegl1-mesa (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libwayland-egl1-mesa (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libopenvg1-mesa (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libegl1-mesa-drivers (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libgles2-mesa (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf libgudev-1.0-0:i386 (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [i386])
Conf libgudev-1.0-0 (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf libxatracker2 (10.1.3-0ubuntu0.4 Ubuntu:14.04/trusty-updates [amd64])
Conf gir1.2-gudev-1.0 (1:204-5ubuntu20.13 Ubuntu:14.04/trusty-updates [amd64])
Conf grub-common (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64])
Conf grub2-common (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64])
Conf grub-pc-bin (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64])
Conf grub-pc (2.02~beta2-9ubuntu1.3 Ubuntu:14.04/trusty-updates [amd64])
Conf xserver-xorg-video-intel (2:2.99.910-0ubuntu1.6 Ubuntu:14.04/trusty-updates [amd64])
toto@AsusET:~$

Heureusement que certains sont dévoués et ont de la patience. smile

Hors ligne

#19 Le 29/08/2015, à 22:34

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

Eh bien je suis étonné mais il n'y a pas de mise à jour du noyau.
Peut-être un choix de Mint.
Fais la mise à jour réelle :

sudo apt-get dist-upgrade

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#20 Le 30/08/2015, à 09:30

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

J'ai redémarré car j'ai eu un doute : cela me semble la même chose.

Après redémarrage, voici le résultat :

toto@AsusET:~$ uname -a
Linux AsusET 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
toto@AsusET:~$

Hors ligne

#21 Le 30/08/2015, à 16:04

moko138

Re : [Résolu] Sata COMRESET failed (errno=-32)

La souris laser :
Si tu manipules son câble, est-ce que ça fait se rallumer et se rééteindre son laser ?
Est-elle bien branchée en usb2 ?
Peux-tu la débrancher et la rebrancher et donner

dmesg | tail -n 35

Peux-tu la tester sur un autre pc ?

Le second disque Sata :
Confirmes-tu que c'est bien celui qui apparaît comme sdf en #8 ? (je pose la question parce que je vois dans fstab qu'il y a un "/volume1/save" en réseau).
  Redémarre et, sitôt sur le bureau, fais

dmesg > dmesg_$(date +%Y%m%d).txt

et colle ici, entre balises-code, le fichier ainsi produit dans ton /home.


%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw

Hors ligne

#22 Le 30/08/2015, à 19:14

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Pour répondre aux différentes questions :
Tout d'abord, je n'ai peut-être pas été assez clair mais la panne de la souris sans fil est aléatoire et à intervalles de temps irrégulier.

- quand je manipule le fil de la souris sans fil, le boîtier sans fil reste toujours allumé.
- je confirme que le branchement est en usb2 : il n'y a pas de port susb3 sur cette carte mère qui date il y a de 4 ou 5 ou 6 ans environ.
- quand je la débranche et que je la rebranche 30 secondes aprs, cela donne les résultats ci-dessous.

toto@AsusET:~$ dmesg | tail -n 35
[   17.900603] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   17.900609] Bluetooth: BNEP filters: protocol multicast
[   17.900623] Bluetooth: BNEP socket layer initialized
[   17.901777] Bluetooth: RFCOMM TTY layer initialized
[   17.901792] Bluetooth: RFCOMM socket layer initialized
[   17.901800] Bluetooth: RFCOMM ver 1.11
[   18.311865] init: cups main process (954) killed by HUP signal
[   18.311882] init: cups main process ended, respawning
[   19.637832] atl1 0000:02:00.0: irq 44 for MSI/MSI-X
[   19.637906] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
[   20.095478] init: samba-ad-dc main process (1036) terminated with status 1
[   22.236964] vboxdrv: module verification failed: signature and/or  required key missing - tainting kernel
[   22.243185] vboxdrv: Found 4 processor cores.
[   22.243450] vboxdrv: fAsync=0 offMin=0x396 offMax=0x164a
[   22.243597] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   22.243600] vboxdrv: Successfully loaded version 4.3.30 (interface 0x001a000a).
[   22.456077] vboxpci: IOMMU not found (not registered)
[   22.999738] init: plymouth-upstart-bridge main process ended, respawning
[   23.008271] init: plymouth-upstart-bridge main process (1827) terminated with status 1
[   23.008288] init: plymouth-upstart-bridge main process ended, respawning
[  174.354518] usb 1-9: reset high-speed USB device number 4 using ehci-pci
[  223.528296] usb 2-2: USB disconnect, device number 2
[  260.883785] usb 2-2: new low-speed USB device number 3 using ohci-pci
[  261.023852] usb 2-2: device descriptor read/64, error -62
[  261.267991] usb 2-2: device descriptor read/64, error -62
[  261.508135] usb 2-2: new low-speed USB device number 4 using ohci-pci
[  261.648211] usb 2-2: device descriptor read/64, error -62
[  261.892343] usb 2-2: device descriptor read/64, error -62
[  262.132485] usb 2-2: new low-speed USB device number 5 using ohci-pci
[  262.171751] usb 2-2: New USB device found, idVendor=045e, idProduct=00e1
[  262.171755] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  262.171757] usb 2-2: Product: Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00
[  262.171760] usb 2-2: Manufacturer: Microsoft
[  262.187704] input: Microsoft Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00 as /devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.0/input/input16
[  262.187912] hid-generic 0003:045E:00E1.0002: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00] on usb-0000:00:13.0-2/input0
toto@AsusET:~$ 

Ensuite, j'ai eu justement aujourd'hui un pc. J'ai pu essayé la souris sans fil. Elle fonctionne parfaitement aussi.

Le second disque sata est bien celui en sdf.
Dans le fstab, le /volume1/save est une sauvegarde branchée en réseau.
En fait, le disuqe sdf est indépendant du sda car ils continnent tous les 2 linuxmint et leurs partitions /home.
Je démarre tout le temps de mon disque principal (celui de 500 Go) et le second disque de 160 Go est là en attente, car je voudrais le mettre en supplément de mon 500 Go car il est bientôt plein. J'y stocke beaucoup de photos.
J'attends de refaire une install de la linuxmint en reprenant mon /home sur mon disque principal et en créant un /home2 sur celui de 160 Go. Mais pour l'instant, il est dans le pc mais ne me sert pas.

Je redémarre et fais un nouveau post pour répondre à ta dernière question sur le disque sata.

Hors ligne

#23 Le 30/08/2015, à 19:21

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Voici le résultat après démarrage de la commande  :
dmesg > dmesg_$(date +%Y%m%d).txt

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.13.0-24-generic (buildd@batsu) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 (Ubuntu 3.13.0-24.47-generic 3.13.9)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-24-generic root=UUID=2a72443c-9f2b-4cd8-8369-60adf2b10462 ro quiet splash vt.handoff=7
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cffaffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cffb0000-0x00000000cffbdfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cffbe000-0x00000000cffdffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cffe0000-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.5 present.
[    0.000000] DMI: System manufacturer System Product Name/M3A, BIOS 0902    05/30/2008
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] No AGP bridge found
[    0.000000] e820: last_pfn = 0x130000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000C0000000 mask FFFFF0000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000130000000 aka 4864M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xcffb0 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01fdd000, 0x01fddfff] PGTABLE
[    0.000000] BRK [0x01fde000, 0x01fdefff] PGTABLE
[    0.000000] BRK [0x01fdf000, 0x01fdffff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x12fe00000-0x12fffffff]
[    0.000000]  [mem 0x12fe00000-0x12fffffff] page 2M
[    0.000000] BRK [0x01fe0000, 0x01fe0fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x12c000000-0x12fdfffff]
[    0.000000]  [mem 0x12c000000-0x12fdfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x12bffffff]
[    0.000000]  [mem 0x100000000-0x12bffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xcffaffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0xbfffffff] page 1G
[    0.000000]  [mem 0xc0000000-0xcfdfffff] page 2M
[    0.000000]  [mem 0xcfe00000-0xcffaffff] page 4k
[    0.000000] RAMDISK: [mem 0x348f4000-0x36471fff]
[    0.000000] ACPI: RSDP 00000000000f98b0 000014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT 00000000cffb0000 000038 (v01 053008 OEMRSDT  20080530 MSFT 00000097)
[    0.000000] ACPI: FACP 00000000cffb0200 000084 (v02 053008 OEMFACP  20080530 MSFT 00000097)
[    0.000000] ACPI: DSDT 00000000cffb0440 00637A (v01  P0004 P0004000 00000000 INTL 20051117)
[    0.000000] ACPI: FACS 00000000cffbe000 000040
[    0.000000] ACPI: APIC 00000000cffb0390 00006C (v01 053008 OEMAPIC  20080530 MSFT 00000097)
[    0.000000] ACPI: MCFG 00000000cffb0400 00003C (v01 053008 OEMMCFG  20080530 MSFT 00000097)
[    0.000000] ACPI: OEMB 00000000cffbe040 000071 (v01 053008 AMI_OEM  20080530 MSFT 00000097)
[    0.000000] ACPI: HPET 00000000cffb67c0 000038 (v01 053008 OEMHPET  20080530 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000012fffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x12fffffff]
[    0.000000]   NODE_DATA [mem 0x12fff9000-0x12fffdfff]
[    0.000000]  [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012b600000-ffff88012f5fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   DMA32    [mem 0x01000000-0xffffffff]
[    0.000000]   Normal   [mem 0x100000000-0x12fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009efff]
[    0.000000]   node   0: [mem 0x00100000-0xcffaffff]
[    0.000000]   node   0: [mem 0x100000000-0x12fffffff]
[    0.000000] On node 0 totalpages: 1048398
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 13247 pages used for memmap
[    0.000000]   DMA32 zone: 847792 pages, LIFO batch:31
[    0.000000]   Normal zone: 3072 pages used for memmap
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xcffb0000-0xcffbdfff]
[    0.000000] PM: Registered nosave memory: [mem 0xcffbe000-0xcffdffff]
[    0.000000] PM: Registered nosave memory: [mem 0xcffe0000-0xcfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xffefffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfff00000-0xffffffff]
[    0.000000] e820: [mem 0xd0000000-0xffefffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 29 pages/cpu @ffff88012fc00000 s86336 r8192 d24256 u524288
[    0.000000] pcpu-alloc: s86336 r8192 d24256 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1031994
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-24-generic root=UUID=2a72443c-9f2b-4cd8-8369-60adf2b10462 ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ c4000000 size 32 MB
[    0.000000] Aperture pointing to e820 RAM. Ignoring.
[    0.000000] Your BIOS doesn't leave a aperture memory hole
[    0.000000] Please enable the IOMMU option in the BIOS setup
[    0.000000] This costs you 64 MB of RAM
[    0.000000] Mapping aperture over 65536 KB of RAM @ c4000000
[    0.000000] PM: Registered nosave memory: [mem 0xc4000000-0xc7ffffff]
[    0.000000] Memory: 3951224K/4193592K available (7338K kernel code, 1138K rwdata, 3388K rodata, 1332K init, 1440K bss, 242368K reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000] 	Offload RCU callbacks from all CPUs
[    0.000000] 	Offload RCU callbacks from CPUs: 0-3.
[    0.000000] NR_IRQS:16640 nr_irqs:712 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 16777216 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.004000] tsc: Detected 1999.990 MHz processor
[    0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3999.98 BogoMIPS (lpj=7999960)
[    0.000008] pid_max: default: 32768 minimum: 301
[    0.000040] Security Framework initialized
[    0.000062] AppArmor: AppArmor initialized
[    0.000063] Yama: becoming mindful.
[    0.000598] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.002429] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.003248] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003259] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003560] Initializing cgroup subsys memory
[    0.003569] Initializing cgroup subsys devices
[    0.003572] Initializing cgroup subsys freezer
[    0.003574] Initializing cgroup subsys blkio
[    0.003577] Initializing cgroup subsys perf_event
[    0.003580] Initializing cgroup subsys hugetlb
[    0.003604] tseg: 0000000000
[    0.003613] CPU: Physical Processor ID: 0
[    0.003614] CPU: Processor Core ID: 0
[    0.003617] mce: CPU supports 6 MCE banks
[    0.003624] LVT offset 0 assigned for vector 0xf9
[    0.003629] process: using AMD E400 aware idle routine
[    0.003633] Last level iTLB entries: 4KB 512, 2MB 16, 4MB 8
[    0.003633] Last level dTLB entries: 4KB 512, 2MB 128, 4MB 64
[    0.003633] tlb_flushall_shift: 4
[    0.003754] Freeing SMP alternatives memory: 32K (ffffffff81e6b000 - ffffffff81e73000)
[    0.004768] ACPI: Core revision 20131115
[    0.007330] ACPI: All ACPI Tables successfully acquired
[    0.007679] ftrace: allocating 28408 entries in 111 pages
[    0.023265] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.062955] smpboot: CPU0: AMD Phenom(tm) 9350e Quad-Core Processor (fam: 10, model: 02, stepping: 03)
[    0.172172] Performance Events: AMD PMU driver.
[    0.172177] ... version:                0
[    0.172179] ... bit width:              48
[    0.172181] ... generic registers:      4
[    0.172182] ... value mask:             0000ffffffffffff
[    0.172184] ... max period:             00007fffffffffff
[    0.172185] ... fixed-purpose events:   0
[    0.172187] ... event mask:             000000000000000f
[    0.174204] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.174321] x86: Booting SMP configuration:
[    0.174324] .... node  #0, CPUs:      #1 #2 #3
[    0.213682] x86: Booted up 1 node, 4 CPUs
[    0.213685] smpboot: Total of 4 processors activated (15999.92 BogoMIPS)
[    0.216457] devtmpfs: initialized
[    0.220689] EVM: security.selinux
[    0.220691] EVM: security.SMACK64
[    0.220693] EVM: security.ima
[    0.220694] EVM: security.capability
[    0.220763] PM: Registering ACPI NVS region [mem 0xcffbe000-0xcffdffff] (139264 bytes)
[    0.222028] pinctrl core: initialized pinctrl subsystem
[    0.222113] regulator-dummy: no parameters
[    0.222148] RTC time: 20:15:51, date: 08/30/15
[    0.222198] NET: Registered protocol family 16
[    0.222351] cpuidle: using governor ladder
[    0.222353] cpuidle: using governor menu
[    0.222360] node 0 link 0: io port [1000, ffffff]
[    0.222364] TOM: 00000000d0000000 aka 3328M
[    0.222367] Fam 10h mmconf [mem 0xe0000000-0xe00fffff]
[    0.222370] node 0 link 0: mmio [e0000000, efffffff] ==> [e0100000, efffffff]
[    0.222375] node 0 link 0: mmio [f0000000, ffffffff]
[    0.222377] node 0 link 0: mmio [a0000, bffff]
[    0.222380] node 0 link 0: mmio [d0000000, dfffffff]
[    0.222382] TOM2: 0000000130000000 aka 4864M
[    0.222385] bus: [bus 00-07] on node 0 link 0
[    0.222386] bus: 00 [io  0x0000-0xffff]
[    0.222388] bus: 00 [mem 0xe0100000-0xffffffff]
[    0.222390] bus: 00 [mem 0x000a0000-0x000bffff]
[    0.222391] bus: 00 [mem 0xd0000000-0xdfffffff]
[    0.222393] bus: 00 [mem 0x130000000-0xfcffffffff]
[    0.222454] ACPI: bus type PCI registered
[    0.222456] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.222530] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.222533] PCI: not using MMCONFIG
[    0.222535] PCI: Using configuration type 1 for base access
[    0.222537] PCI: Using configuration type 1 for extended access
[    0.222743] mtrr: your CPUs had inconsistent variable MTRR settings
[    0.222744] mtrr: probably your BIOS does not setup all CPUs.
[    0.222746] mtrr: corrected configuration.
[    0.223811] bio: create slab <bio-0> at 0
[    0.224036] ACPI: Added _OSI(Module Device)
[    0.224039] ACPI: Added _OSI(Processor Device)
[    0.224041] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.224042] ACPI: Added _OSI(Processor Aggregator Device)
[    0.226296] ACPI: Executed 2 blocks of module-level executable AML code
[    0.230568] ACPI: Interpreter enabled
[    0.230582] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
[    0.230600] ACPI: (supports S0 S1 S3 S4 S5)
[    0.230602] ACPI: Using IOAPIC for interrupt routing
[    0.230672] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.231272] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.242908] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.243112] ACPI: No dock devices found.
[    0.251923] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.251932] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.251938] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.252329] PCI host bridge to bus 0000:00
[    0.252333] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.252336] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.252339] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.252342] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.252344] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
[    0.252347] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xdfffffff]
[    0.252349] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff]
[    0.252364] pci 0000:00:00.0: [1002:5957] type 00 class 0x060000
[    0.252382] pci 0000:00:00.0: reg 0x1c: [mem 0xe0000000-0xffffffff 64bit]
[    0.252511] pci 0000:00:02.0: [1002:5978] type 01 class 0x060400
[    0.252561] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.252619] pci 0000:00:02.0: System wakeup disabled by ACPI
[    0.252660] pci 0000:00:06.0: [1002:597c] type 01 class 0x060400
[    0.252708] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.252763] pci 0000:00:06.0: System wakeup disabled by ACPI
[    0.252819] pci 0000:00:12.0: [1002:4380] type 00 class 0x01018f
[    0.252840] pci 0000:00:12.0: reg 0x10: [io  0xd000-0xd007]
[    0.252852] pci 0000:00:12.0: reg 0x14: [io  0xc000-0xc003]
[    0.252864] pci 0000:00:12.0: reg 0x18: [io  0xb000-0xb007]
[    0.252875] pci 0000:00:12.0: reg 0x1c: [io  0xa000-0xa003]
[    0.252887] pci 0000:00:12.0: reg 0x20: [io  0x9000-0x900f]
[    0.252899] pci 0000:00:12.0: reg 0x24: [mem 0xfe9ff800-0xfe9ffbff]
[    0.252923] pci 0000:00:12.0: set SATA to AHCI mode
[    0.253029] pci 0000:00:13.0: [1002:4387] type 00 class 0x0c0310
[    0.253046] pci 0000:00:13.0: reg 0x10: [mem 0xfe9fe000-0xfe9fefff]
[    0.253160] pci 0000:00:13.0: System wakeup disabled by ACPI
[    0.253197] pci 0000:00:13.1: [1002:4388] type 00 class 0x0c0310
[    0.253213] pci 0000:00:13.1: reg 0x10: [mem 0xfe9fd000-0xfe9fdfff]
[    0.253328] pci 0000:00:13.1: System wakeup disabled by ACPI
[    0.253362] pci 0000:00:13.2: [1002:4389] type 00 class 0x0c0310
[    0.253379] pci 0000:00:13.2: reg 0x10: [mem 0xfe9fc000-0xfe9fcfff]
[    0.253493] pci 0000:00:13.2: System wakeup disabled by ACPI
[    0.253528] pci 0000:00:13.3: [1002:438a] type 00 class 0x0c0310
[    0.253544] pci 0000:00:13.3: reg 0x10: [mem 0xfe9fb000-0xfe9fbfff]
[    0.253657] pci 0000:00:13.3: System wakeup disabled by ACPI
[    0.253692] pci 0000:00:13.4: [1002:438b] type 00 class 0x0c0310
[    0.253708] pci 0000:00:13.4: reg 0x10: [mem 0xfe9fa000-0xfe9fafff]
[    0.253824] pci 0000:00:13.4: System wakeup disabled by ACPI
[    0.253868] pci 0000:00:13.5: [1002:4386] type 00 class 0x0c0320
[    0.253893] pci 0000:00:13.5: reg 0x10: [mem 0xfe9ff000-0xfe9ff0ff]
[    0.254002] pci 0000:00:13.5: supports D1 D2
[    0.254005] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[    0.254064] pci 0000:00:13.5: System wakeup disabled by ACPI
[    0.254106] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[    0.254132] pci 0000:00:14.0: reg 0x10: [io  0x0b00-0x0b0f]
[    0.254295] pci 0000:00:14.1: [1002:438c] type 00 class 0x01018a
[    0.254317] pci 0000:00:14.1: reg 0x10: [io  0x0000-0x0007]
[    0.254329] pci 0000:00:14.1: reg 0x14: [io  0x0000-0x0003]
[    0.254341] pci 0000:00:14.1: reg 0x18: [io  0x0000-0x0007]
[    0.254352] pci 0000:00:14.1: reg 0x1c: [io  0x0000-0x0003]
[    0.254364] pci 0000:00:14.1: reg 0x20: [io  0xff00-0xff0f]
[    0.254474] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[    0.254500] pci 0000:00:14.2: reg 0x10: [mem 0xfe9f4000-0xfe9f7fff 64bit]
[    0.254579] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.254634] pci 0000:00:14.2: System wakeup disabled by ACPI
[    0.254673] pci 0000:00:14.3: [1002:438d] type 00 class 0x060100
[    0.254826] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[    0.254914] pci 0000:00:14.4: System wakeup disabled by ACPI
[    0.254955] pci 0000:00:18.0: [1022:1200] type 00 class 0x060000
[    0.255047] pci 0000:00:18.1: [1022:1201] type 00 class 0x060000
[    0.255131] pci 0000:00:18.2: [1022:1202] type 00 class 0x060000
[    0.255215] pci 0000:00:18.3: [1022:1203] type 00 class 0x060000
[    0.255306] pci 0000:00:18.4: [1022:1204] type 00 class 0x060000
[    0.255452] pci 0000:01:00.0: [1002:68f9] type 00 class 0x030000
[    0.255468] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.255481] pci 0000:01:00.0: reg 0x18: [mem 0xfeae0000-0xfeafffff 64bit]
[    0.255490] pci 0000:01:00.0: reg 0x20: [io  0xe000-0xe0ff]
[    0.255505] pci 0000:01:00.0: reg 0x30: [mem 0xfeac0000-0xfeadffff pref]
[    0.255542] pci 0000:01:00.0: supports D1 D2
[    0.255591] pci 0000:01:00.1: [1002:aa68] type 00 class 0x040300
[    0.255606] pci 0000:01:00.1: reg 0x10: [mem 0xfeabc000-0xfeabffff 64bit]
[    0.255675] pci 0000:01:00.1: supports D1 D2
[    0.262324] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.262330] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.262334] pci 0000:00:02.0:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.262339] pci 0000:00:02.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.262403] pci 0000:02:00.0: [1969:1048] type 00 class 0x020000
[    0.262424] pci 0000:02:00.0: reg 0x10: [mem 0xfebc0000-0xfebfffff 64bit]
[    0.262474] pci 0000:02:00.0: reg 0x30: [mem 0xfeba0000-0xfebbffff pref]
[    0.262533] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.262581] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.262590] pci 0000:00:06.0: PCI bridge to [bus 02]
[    0.262596] pci 0000:00:06.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.262680] pci 0000:00:14.4: PCI bridge to [bus 03] (subtractive decode)
[    0.262691] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.262694] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.262696] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.262699] pci 0000:00:14.4:   bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[    0.262702] pci 0000:00:14.4:   bridge window [mem 0xd0000000-0xdfffffff] (subtractive decode)
[    0.262704] pci 0000:00:14.4:   bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode)
[    0.263534] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263591] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263645] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263698] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263751] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263804] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[    0.263853] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.263906] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.264072] ACPI: Enabled 2 GPEs in block 00 to 1F
[    0.264079] ACPI: \_SB_.PCI0: notify handler is installed
[    0.264124] Found 1 acpi root devices
[    0.264257] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.264259] vgaarb: loaded
[    0.264261] vgaarb: bridge control possible 0000:01:00.0
[    0.264481] SCSI subsystem initialized
[    0.264538] libata version 3.00 loaded.
[    0.264565] ACPI: bus type USB registered
[    0.264587] usbcore: registered new interface driver usbfs
[    0.264597] usbcore: registered new interface driver hub
[    0.264630] usbcore: registered new device driver usb
[    0.264772] PCI: Using ACPI for IRQ routing
[    0.274999] PCI: pci_cache_line_size set to 64 bytes
[    0.275006] pci 0000:00:00.0: no compatible bridge window for [mem 0xe0000000-0xffffffff 64bit]
[    0.275064] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.275067] e820: reserve RAM buffer [mem 0xcffb0000-0xcfffffff]
[    0.275178] NetLabel: Initializing
[    0.275180] NetLabel:  domain hash size = 128
[    0.275181] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.275197] NetLabel:  unlabeled traffic allowed by default
[    0.275272] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.275277] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[    0.277345] Switched to clocksource hpet
[    0.285005] AppArmor: AppArmor Filesystem Enabled
[    0.285046] pnp: PnP ACPI init
[    0.285066] ACPI: bus type PNP registered
[    0.285144] pnp 00:00: [dma 4]
[    0.285184] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.285228] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.285258] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.285290] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.285852] pnp 00:04: [dma 2]
[    0.285906] pnp 00:04: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.285976] pnp 00:05: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.286080] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.286084] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.286088] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.286264] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.286267] system 00:07: [io  0x040b] has been reserved
[    0.286270] system 00:07: [io  0x04d6] has been reserved
[    0.286273] system 00:07: [io  0x0c00-0x0c01] has been reserved
[    0.286276] system 00:07: [io  0x0c14] has been reserved
[    0.286279] system 00:07: [io  0x0c50-0x0c51] has been reserved
[    0.286281] system 00:07: [io  0x0c52] has been reserved
[    0.286284] system 00:07: [io  0x0c6c] has been reserved
[    0.286287] system 00:07: [io  0x0c6f] has been reserved
[    0.286289] system 00:07: [io  0x0cd0-0x0cd1] has been reserved
[    0.286292] system 00:07: [io  0x0cd2-0x0cd3] has been reserved
[    0.286295] system 00:07: [io  0x0cd4-0x0cd5] has been reserved
[    0.286297] system 00:07: [io  0x0cd6-0x0cd7] has been reserved
[    0.286300] system 00:07: [io  0x0cd8-0x0cdf] has been reserved
[    0.286303] system 00:07: [io  0x0800-0x089f] could not be reserved
[    0.286306] system 00:07: [io  0x0b10-0x0b1f] has been reserved
[    0.286309] system 00:07: [io  0x0900-0x090f] has been reserved
[    0.286311] system 00:07: [io  0x0910-0x091f] has been reserved
[    0.286314] system 00:07: [io  0xfe00-0xfefe] has been reserved
[    0.286318] system 00:07: [mem 0xffb80000-0xffbfffff] has been reserved
[    0.286323] system 00:07: [mem 0xfff00000-0xffffffff] has been reserved
[    0.286327] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.286385] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.286459] pnp 00:09: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
[    0.286914] pnp 00:0a: [dma 0 disabled]
[    0.286981] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.287166] system 00:0b: [io  0x0e00-0x0e0f] has been reserved
[    0.287169] system 00:0b: [io  0x0e80-0x0e8f] has been reserved
[    0.287172] system 00:0b: [io  0x0f40-0x0f4f] has been reserved
[    0.287175] system 00:0b: [io  0x0a30-0x0a3f] has been reserved
[    0.287178] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.287244] system 00:0c: [mem 0xe0000000-0xefffffff] has been reserved
[    0.287247] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.287440] pnp 00:0d: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
[    0.287444] pnp 00:0d: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
[    0.287448] pnp 00:0d: disabling [mem 0x000e0000-0x000fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
[    0.287451] pnp 00:0d: disabling [mem 0x00100000-0xcfffffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
[    0.287494] system 00:0d: [mem 0xfec00000-0xffffffff] could not be reserved
[    0.287497] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.287607] pnp: PnP ACPI: found 14 devices
[    0.287608] ACPI: bus type PNP unregistered
[    0.294523] pci 0000:00:02.0: PCI bridge to [bus 01]
[    0.294528] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.294533] pci 0000:00:02.0:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.294537] pci 0000:00:02.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.294542] pci 0000:00:06.0: PCI bridge to [bus 02]
[    0.294546] pci 0000:00:06.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.294552] pci 0000:00:14.4: PCI bridge to [bus 03]
[    0.294567] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.294569] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.294572] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.294574] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[    0.294576] pci_bus 0000:00: resource 8 [mem 0xd0000000-0xdfffffff]
[    0.294578] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
[    0.294581] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.294583] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
[    0.294586] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.294589] pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
[    0.294592] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.294594] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.294596] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.294599] pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff]
[    0.294601] pci_bus 0000:03: resource 8 [mem 0xd0000000-0xdfffffff]
[    0.294603] pci_bus 0000:03: resource 9 [mem 0xf0000000-0xfebfffff]
[    0.294647] NET: Registered protocol family 2
[    0.294859] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.295009] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.295213] TCP: Hash tables configured (established 32768 bind 32768)
[    0.295266] TCP: reno registered
[    0.295274] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.295315] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.295418] NET: Registered protocol family 1
[    0.749741] pci 0000:01:00.0: Boot video device
[    0.749750] PCI: CLS 64 bytes, default 64
[    0.749829] Trying to unpack rootfs image as initramfs...
[    1.357300] Freeing initrd memory: 28152K (ffff8800348f4000 - ffff880036472000)
[    1.357629] PCI-DMA: Disabling AGP.
[    1.357725] PCI-DMA: aperture base @ c4000000 size 65536 KB
[    1.357727] PCI-DMA: using GART IOMMU.
[    1.357731] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    1.362599] LVT offset 1 assigned for vector 0x400
[    1.362613] IBS: LVT offset 1 assigned
[    1.362646] perf: AMD IBS detected (0x00000007)
[    1.362706] microcode: CPU0: patch_level=0x01000065
[    1.362712] microcode: CPU1: patch_level=0x01000065
[    1.362723] microcode: CPU2: patch_level=0x01000065
[    1.362737] microcode: CPU3: patch_level=0x01000065
[    1.362797] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.362799] Scanning for low memory corruption every 60 seconds
[    1.363086] Initialise system trusted keyring
[    1.363157] audit: initializing netlink socket (disabled)
[    1.363174] type=2000 audit(1440965752.248:1): initialized
[    1.395818] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.397594] VFS: Disk quotas dquot_6.5.2
[    1.397652] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.398233] fuse init (API version 7.22)
[    1.398323] msgmni has been set to 7901
[    1.398393] Key type big_key registered
[    1.399018] Key type asymmetric registered
[    1.399021] Asymmetric key parser 'x509' registered
[    1.399075] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.399153] io scheduler noop registered
[    1.399156] io scheduler deadline registered (default)
[    1.399217] io scheduler cfq registered
[    1.399371] pcieport 0000:00:02.0: irq 40 for MSI/MSI-X
[    1.399440] pcieport 0000:00:06.0: irq 41 for MSI/MSI-X
[    1.399508] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.399526] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.399575] vesafb: mode is 1400x1050x32, linelength=5632, pages=0
[    1.399577] vesafb: scrolling: redraw
[    1.399579] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    1.399890] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90010780000, using 5824k, total 5824k
[    1.417779] Console: switching to colour frame buffer device 175x65
[    1.435460] fb0: VESA VGA frame buffer device
[    1.435486] ipmi message handler version 39.2
[    1.435567] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[    1.435574] ACPI: Power Button [PWRB]
[    1.435620] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    1.435623] ACPI: Power Button [PWRF]
[    1.435659] ACPI: duty_cycle spans bit 4
[    1.435791] GHES: HEST is not enabled!
[    1.435900] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    1.456447] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.458083] Linux agpgart interface v0.103
[    1.459729] brd: module loaded
[    1.460626] loop: module loaded
[    1.461099] libphy: Fixed MDIO Bus: probed
[    1.461206] tun: Universal TUN/TAP device driver, 1.6
[    1.461208] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.461256] PPP generic driver version 2.4.2
[    1.461303] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.461308] ehci-pci: EHCI PCI platform driver
[    1.461523] ehci-pci 0000:00:13.5: EHCI Host Controller
[    1.461531] ehci-pci 0000:00:13.5: new USB bus registered, assigned bus number 1
[    1.461537] ehci-pci 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[    1.461556] ehci-pci 0000:00:13.5: debug port 1
[    1.461612] ehci-pci 0000:00:13.5: irq 19, io mem 0xfe9ff000
[    1.473439] ehci-pci 0000:00:13.5: USB 2.0 started, EHCI 1.00
[    1.473496] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.473499] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.473501] usb usb1: Product: EHCI Host Controller
[    1.473503] usb usb1: Manufacturer: Linux 3.13.0-24-generic ehci_hcd
[    1.473505] usb usb1: SerialNumber: 0000:00:13.5
[    1.473630] hub 1-0:1.0: USB hub found
[    1.473639] hub 1-0:1.0: 10 ports detected
[    1.473855] ehci-platform: EHCI generic platform driver
[    1.473865] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.473866] ohci-pci: OHCI PCI platform driver
[    1.474006] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    1.474012] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[    1.474038] ohci-pci 0000:00:13.0: irq 16, io mem 0xfe9fe000
[    1.533467] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.533469] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.533472] usb usb2: Product: OHCI PCI host controller
[    1.533474] usb usb2: Manufacturer: Linux 3.13.0-24-generic ohci_hcd
[    1.533476] usb usb2: SerialNumber: 0000:00:13.0
[    1.533604] hub 2-0:1.0: USB hub found
[    1.533619] hub 2-0:1.0: 2 ports detected
[    1.533888] ohci-pci 0000:00:13.1: OHCI PCI host controller
[    1.533895] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 3
[    1.533930] ohci-pci 0000:00:13.1: irq 17, io mem 0xfe9fd000
[    1.593476] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.593478] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.593480] usb usb3: Product: OHCI PCI host controller
[    1.593483] usb usb3: Manufacturer: Linux 3.13.0-24-generic ohci_hcd
[    1.593485] usb usb3: SerialNumber: 0000:00:13.1
[    1.593592] hub 3-0:1.0: USB hub found
[    1.593603] hub 3-0:1.0: 2 ports detected
[    1.593814] ohci-pci 0000:00:13.2: OHCI PCI host controller
[    1.593820] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 4
[    1.593842] ohci-pci 0000:00:13.2: irq 18, io mem 0xfe9fc000
[    1.653473] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.653476] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.653478] usb usb4: Product: OHCI PCI host controller
[    1.653480] usb usb4: Manufacturer: Linux 3.13.0-24-generic ohci_hcd
[    1.653482] usb usb4: SerialNumber: 0000:00:13.2
[    1.653623] hub 4-0:1.0: USB hub found
[    1.653636] hub 4-0:1.0: 2 ports detected
[    1.653921] ohci-pci 0000:00:13.3: OHCI PCI host controller
[    1.653928] ohci-pci 0000:00:13.3: new USB bus registered, assigned bus number 5
[    1.653951] ohci-pci 0000:00:13.3: irq 17, io mem 0xfe9fb000
[    1.713500] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.713502] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.713505] usb usb5: Product: OHCI PCI host controller
[    1.713507] usb usb5: Manufacturer: Linux 3.13.0-24-generic ohci_hcd
[    1.713509] usb usb5: SerialNumber: 0000:00:13.3
[    1.713615] hub 5-0:1.0: USB hub found
[    1.713625] hub 5-0:1.0: 2 ports detected
[    1.713829] ohci-pci 0000:00:13.4: OHCI PCI host controller
[    1.713835] ohci-pci 0000:00:13.4: new USB bus registered, assigned bus number 6
[    1.713849] ohci-pci 0000:00:13.4: irq 18, io mem 0xfe9fa000
[    1.773490] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    1.773493] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.773495] usb usb6: Product: OHCI PCI host controller
[    1.773497] usb usb6: Manufacturer: Linux 3.13.0-24-generic ohci_hcd
[    1.773499] usb usb6: SerialNumber: 0000:00:13.4
[    1.773607] hub 6-0:1.0: USB hub found
[    1.773620] hub 6-0:1.0: 2 ports detected
[    1.773704] ohci-platform: OHCI generic platform driver
[    1.773717] uhci_hcd: USB Universal Host Controller Interface driver
[    1.773796] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.774178] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.774183] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.774312] mousedev: PS/2 mouse device common for all mice
[    1.774464] rtc_cmos 00:01: RTC can wake from S4
[    1.774593] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.774622] rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.774697] device-mapper: uevent: version 1.0.3
[    1.774766] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    1.774774] ledtrig-cpu: registered to indicate activity on CPUs
[    1.774906] TCP: cubic registered
[    1.775015] NET: Registered protocol family 10
[    1.775240] NET: Registered protocol family 17
[    1.775255] Key type dns_resolver registered
[    1.775597] Loading compiled-in X.509 certificates
[    1.776967] Loaded X.509 cert 'Magrathea: Glacier signing key: 69b0d0a79b85d90621706e8d06604d730b359fc0'
[    1.776984] registered taskstats version 1
[    1.780045] Key type trusted registered
[    1.782427] Key type encrypted registered
[    1.784772] AppArmor: AppArmor sha1 policy hashing enabled
[    1.784775] IMA: No TPM chip found, activating TPM-bypass!
[    1.785036] regulator-dummy: disabling
[    1.785093]   Magic number: 11:110:297
[    1.785212] rtc_cmos 00:01: setting system clock to 2015-08-30 20:15:52 UTC (1440965752)
[    1.785292] powernow-k8: This CPU is not supported anymore, using acpi-cpufreq instead.
[    1.786670] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.786674] EDD information not available.
[    1.786714] PM: Hibernation image not present or could not be loaded.
[    1.788644] Freeing unused kernel memory: 1332K (ffffffff81d1e000 - ffffffff81e6b000)
[    1.788647] Write protecting the kernel read-only data: 12288k
[    1.791910] Freeing unused kernel memory: 844K (ffff88000172d000 - ffff880001800000)
[    1.794511] Freeing unused kernel memory: 708K (ffff880001b4f000 - ffff880001c00000)
[    1.796342] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    1.813202] systemd-udevd[118]: starting version 204
[    1.833104] Floppy drive(s): fd0 is 1.44M
[    1.838489] ahci 0000:00:12.0: version 3.0
[    1.838682] ahci 0000:00:12.0: ASUS M3A: enabling 64bit DMA
[    1.838777] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    1.838782] ahci 0000:00:12.0: flags: 64bit ncq sntf ilck led clo pmp pio ccc 
[    1.841135] scsi0 : ahci
[    1.841499] usb 1-4: new high-speed USB device number 3 using ehci-pci
[    1.841643] [drm] Initialized drm 1.1.0 20060810
[    1.842954] scsi1 : ahci
[    1.843046] scsi2 : ahci
[    1.843120] scsi3 : ahci
[    1.843173] ata1: SATA max UDMA/133 abar m1024@0xfe9ff800 port 0xfe9ff900 irq 22
[    1.843177] ata2: SATA max UDMA/133 abar m1024@0xfe9ff800 port 0xfe9ff980 irq 22
[    1.843181] ata3: SATA max UDMA/133 abar m1024@0xfe9ff800 port 0xfe9ffa00 irq 22
[    1.843184] ata4: SATA max UDMA/133 abar m1024@0xfe9ff800 port 0xfe9ffa80 irq 22
[    1.843895] atl1 0000:02:00.0: version 2.1.3
[    1.844883] scsi4 : pata_atiixp
[    1.845257] scsi5 : pata_atiixp
[    1.845302] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[    1.845305] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[    1.851247] FDC 0 is a post-1991 82077
[    1.886779] [drm] radeon kernel modesetting enabled.
[    1.886872] checking generic (d0000000 5b0000) vs hw (d0000000 10000000)
[    1.886874] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
[    1.886896] Console: switching to colour dummy device 80x25
[    1.887290] [drm] initializing kernel modesetting (CEDAR 0x1002:0x68F9 0x1462:0x2127).
[    1.887310] [drm] register mmio base: 0xFEAE0000
[    1.887312] [drm] register mmio size: 131072
[    1.888119] ATOM BIOS: 113
[    1.888178] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[    1.888181] radeon 0000:01:00.0: GTT: 1024M 0x0000000040000000 - 0x000000007FFFFFFF
[    1.888184] [drm] Detected VRAM RAM=1024M, BAR=256M
[    1.888185] [drm] RAM width 64bits DDR
[    1.888276] [TTM] Zone  kernel: Available graphics memory: 2024122 kiB
[    1.888281] [TTM] Initializing pool allocator
[    1.888290] [TTM] Initializing DMA pool allocator
[    1.888318] [drm] radeon: 1024M of VRAM memory ready
[    1.888320] [drm] radeon: 1024M of GTT memory ready.
[    1.888337] [drm] Loading CEDAR Microcode
[    1.888673] [drm] GART: num cpu pages 262144, num gpu pages 262144
[    1.891006] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[    1.904830] [drm] PCIE GART of 1024M enabled (table at 0x000000000025D000).
[    1.904927] radeon 0000:01:00.0: WB enabled
[    1.904932] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff880123c59c00
[    1.904935] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff880123c59c0c
[    1.905411] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x000000000005c418 and cpu addr 0xffffc90010e9c418
[    1.905414] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.905416] [drm] Driver supports precise vblank timestamp query.
[    1.905446] radeon 0000:01:00.0: irq 42 for MSI/MSI-X
[    1.906137] radeon 0000:01:00.0: radeon: using MSI.
[    1.906170] [drm] radeon: irq initialized.
[    1.922357] [drm] ring test on 0 succeeded in 1 usecs
[    1.922415] [drm] ring test on 3 succeeded in 1 usecs
[    2.005941] ata5.00: ATAPI: HL-DT-ST DVDRAM GSA-4165B, DL03, max UDMA/33
[    2.021880] ata5.00: configured for UDMA/33
[    2.118656] [drm] ring test on 5 succeeded in 1 usecs
[    2.118661] [drm] UVD initialized successfully.
[    2.118783] [drm] Enabling audio 0 support
[    2.118812] [drm] ib test on ring 0 succeeded in 0 usecs
[    2.118838] [drm] ib test on ring 3 succeeded in 0 usecs
[    2.161527] ata4: SATA link down (SStatus 0 SControl 300)
[    2.245667] usb 1-4: New USB device found, idVendor=046d, idProduct=0826
[    2.245671] usb 1-4: New USB device strings: Mfr=0, Product=2, SerialNumber=1
[    2.245674] usb 1-4: Product: HD Webcam C525
[    2.245677] usb 1-4: SerialNumber: 877B6460
[    2.289041] [drm] ib test on ring 5 succeeded
[    2.289564] [drm] Radeon Display Connectors
[    2.289567] [drm] Connector 0:
[    2.289568] [drm]   HDMI-A-1
[    2.289570] [drm]   HPD2
[    2.289572] [drm]   DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[    2.289573] [drm]   Encoders:
[    2.289575] [drm]     DFP1: INTERNAL_UNIPHY1
[    2.289576] [drm] Connector 1:
[    2.289578] [drm]   DVI-D-1
[    2.289579] [drm]   HPD4
[    2.289581] [drm]   DDC: 0x6460 0x6460 0x6464 0x6464 0x6468 0x6468 0x646c 0x646c
[    2.289582] [drm]   Encoders:
[    2.289583] [drm]     DFP2: INTERNAL_UNIPHY
[    2.289585] [drm] Connector 2:
[    2.289586] [drm]   VGA-1
[    2.289588] [drm]   DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[    2.289589] [drm]   Encoders:
[    2.289591] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    2.289643] [drm] Internal thermal controller with fan control
[    2.291532] [drm] radeon: dpm initialized
[    2.333504] ata1: softreset failed (device not ready)
[    2.333509] ata1: applying PMP SRST workaround and retrying
[    2.333526] ata3: softreset failed (device not ready)
[    2.333530] ata3: applying PMP SRST workaround and retrying
[    2.335797] [drm] fb mappable at 0xD045E000
[    2.335800] [drm] vram apper at 0xD0000000
[    2.335802] [drm] size 7299072
[    2.335803] [drm] fb depth is 24
[    2.335805] [drm]    pitch is 6912
[    2.335878] fbcon: radeondrmfb (fb0) is primary device
[    2.350601] Console: switching to colour frame buffer device 210x65
[    2.357527] usb 1-9: new high-speed USB device number 4 using ehci-pci
[    2.357910] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    2.357913] radeon 0000:01:00.0: registered panic notifier
[    2.357920] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
[    2.361508] tsc: Refined TSC clocksource calibration: 2000.139 MHz
[    2.505530] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.505559] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.506196] ata3.00: ATAPI: TSSTcorpDVD-ROM SH-D163B, SB02, max UDMA/33
[    2.506201] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.507810] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.507813] ata3.00: configured for UDMA/33
[    2.511991] ata1.00: ATA-7: SAMSUNG HD502IJ, 1AA01113, max UDMA7
[    2.511994] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.511997] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.518482] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.518484] ata1.00: configured for UDMA/133
[    2.518667] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD502IJ  1AA0 PQ: 0 ANSI: 5
[    2.518848] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    2.518877] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.518985] sd 0:0:0:0: [sda] Write Protect is off
[    2.518990] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.519066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.569665]  sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[    2.570257] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.033685] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[    3.044700] usb 1-9: New USB device found, idVendor=0bda, idProduct=0151
[    3.044704] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.044707] usb 1-9: Product: USB2.0-CRW
[    3.044709] usb 1-9: Manufacturer: Generic
[    3.044712] usb 1-9: SerialNumber: 20060413092100000
[    3.177978] usb-storage 1-9:1.0: USB Mass Storage device detected
[    3.178070] scsi6 : usb-storage 1-9:1.0
[    3.178154] usbcore: registered new interface driver usb-storage
[    3.309574] usb 2-2: new low-speed USB device number 2 using ohci-pci
[    3.361647] Switched to clocksource tsc
[    3.482607] usb 2-2: New USB device found, idVendor=045e, idProduct=00e1
[    3.482611] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.482614] usb 2-2: Product: Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00
[    3.482616] usb 2-2: Manufacturer: Microsoft
[    3.488586] hidraw: raw HID events driver (C) Jiri Kosina
[    3.504081] usbcore: registered new interface driver usbhid
[    3.504084] usbhid: USB HID core driver
[    3.506440] input: Microsoft Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00 as /devices/pci0000:00/0000:00:13.0/usb2/2-2/2-2:1.0/input/input5
[    3.506576] hid-generic 0003:045E:00E1.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse\xffffffc2\xffffffae\xffffffae 1.00] on usb-0000:00:13.0-2/input0
[    4.069615] ata2: COMRESET failed (errno=-32)
[    4.069623] ata2: reset failed (errno=-32), retrying in 8 secs
[    4.184085] scsi 6:0:0:0: Direct-Access     Generic- Compact Flash    1.00 PQ: 0 ANSI: 0 CCS
[    4.190322] scsi 6:0:0:1: Direct-Access     Generic- SM/xD-Picture    1.00 PQ: 0 ANSI: 0 CCS
[    4.196572] scsi 6:0:0:2: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 CCS
[    4.202823] scsi 6:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.00 PQ: 0 ANSI: 0 CCS
[    4.203065] sd 6:0:0:0: Attached scsi generic sg1 type 0
[    4.203272] sd 6:0:0:1: Attached scsi generic sg2 type 0
[    4.203530] sd 6:0:0:2: Attached scsi generic sg3 type 0
[    4.203759] sd 6:0:0:3: Attached scsi generic sg4 type 0
[    4.213698] sd 6:0:0:1: [sdc] Attached SCSI removable disk
[    4.217459] sd 6:0:0:2: [sdd] Attached SCSI removable disk
[    4.218961] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[    4.220460] sd 6:0:0:3: [sde] Attached SCSI removable disk
[   11.842161] ata2: limiting SATA link speed to 1.5 Gbps
[   14.082312] ata2: COMRESET failed (errno=-32)
[   14.082321] ata2: reset failed (errno=-32), retrying in 8 secs
[   24.059023] ata2: SATA link down (SStatus 1 SControl 310)
[   24.060210] scsi 2:0:0:0: CD-ROM            TSSTcorp DVD-ROM SH-D163B SB02 PQ: 0 ANSI: 5
[   24.062820] sr0: scsi3-mmc drive: 4x/48x cd/rw xa/form2 cdda tray
[   24.062823] cdrom: Uniform CD-ROM driver Revision: 3.20
[   24.062958] sr 2:0:0:0: Attached scsi CD-ROM sr0
[   24.063073] sr 2:0:0:0: Attached scsi generic sg5 type 5
[   24.066903] scsi 4:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-4165B DL03 PQ: 0 ANSI: 5
[   24.072407] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   24.072512] sr 4:0:0:0: Attached scsi CD-ROM sr1
[   24.072584] sr 4:0:0:0: Attached scsi generic sg6 type 5
[   24.502085] random: nonblocking pool is initialized
[   24.902838] EXT4-fs (sda7): INFO: recovery required on readonly filesystem
[   24.902844] EXT4-fs (sda7): write access will be enabled during recovery
[   25.677302] EXT4-fs (sda7): recovery complete
[   25.685455] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[   35.766321] Adding 6144824k swap on /dev/sda5.  Priority:-1 extents:1 across:6144824k FS
[   35.787350] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   35.856965] systemd-udevd[406]: starting version 204
[   35.954925] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   36.015619] lp: driver loaded but no devices found
[   36.027417] ppdev: user-space parallel port driver
[   36.032524] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[   36.032589] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb10
[   36.034891] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[   36.035014] sp5100_tco: PCI Revision ID: 0x14
[   36.035033] sp5100_tco: failed to find MMIO address, giving up.
[   36.048094] MCE: In-kernel MCE decoding enabled.
[   36.049802] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[   36.051483] EDAC MC: Ver: 3.0.0
[   36.055289] AMD64 EDAC driver v3.4.0
[   36.055331] EDAC amd64: DRAM ECC disabled.
[   36.055339] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[   36.055339]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[   36.055339]  (Note that use of the override may cause unknown side effects.)
[   36.061586] device-mapper: multipath: version 1.6.0 loaded
[   36.101947] hda-intel 0000:00:14.2: Using LPIB position fix
[   36.107274] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[   36.121265] SKU: Nid=0x1d sku_cfg=0x4015e601
[   36.121270] SKU: port_connectivity=0x1
[   36.121272] SKU: enable_pcbeep=0x1
[   36.121274] SKU: check_sum=0x00000005
[   36.121276] SKU: customization=0x000000e6
[   36.121277] SKU: external_amp=0x0
[   36.121278] SKU: platform_type=0x0
[   36.121279] SKU: swap=0x0
[   36.121281] SKU: override=0x1
[   36.122447] autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[   36.122452]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   36.122454]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   36.122456]    mono: mono_out=0x0
[   36.122457]    dig-out=0x1e/0x0
[   36.122459]    inputs:
[   36.122461]      Front Mic=0x19
[   36.122463]      Rear Mic=0x18
[   36.122465]      Line=0x1a
[   36.122467] realtek: No valid SSID, checking pincfg 0x4015e601 for NID 0x1d
[   36.122469] realtek: Enabling init ASM_ID=0xe601 CODEC_ID=10ec0883
[   36.131415] kvm: Nested Virtualization enabled
[   36.131422] kvm: Nested Paging enabled
[   36.145708] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
[   36.146004] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[   36.146875] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[   36.146996] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[   36.147098] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[   36.147260] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[   36.147372] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[   36.147485] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
[   36.148032] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   36.148037] hda-intel 0000:01:00.1: Using LPIB position fix
[   36.148093] snd_hda_intel 0000:01:00.1: irq 43 for MSI/MSI-X
[   36.155440] hda-intel 0000:01:00.1: Enable sync_write for stable communication
[   36.160478] HDMI ATI/AMD: no speaker allocation for ELD
[   36.160575] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input14
[   36.322745] Linux video capture interface: v2.00
[   36.337326] uvcvideo: Found UVC 1.00 device HD Webcam C525 (046d:0826)
[   36.383749] input: HD Webcam C525 as /devices/pci0000:00/0000:00:13.5/usb1/1-4/1-4:1.2/input/input15
[   36.383981] usbcore: registered new interface driver uvcvideo
[   36.383984] USB Video Class driver (1.1.1)
[   36.416107] set resolution quirk: cval->res = 384
[   36.416349] usbcore: registered new interface driver snd-usb-audio
[   36.431765] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE
[   37.099351] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[   37.571844] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   37.699765] FS-Cache: Loaded
[   37.709543] RPC: Registered named UNIX socket transport module.
[   37.709549] RPC: Registered udp transport module.
[   37.709551] RPC: Registered tcp transport module.
[   37.709553] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   37.722170] FS-Cache: Netfs 'nfs' registered for caching
[   37.736989] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   37.812220] init: failsafe main process (873) killed by TERM signal
[   38.375466] init: idmapd-mounting (/media/diskstation_save) main process (784) killed by TERM signal
[   38.390886] NFS: Registering the id_resolver key type
[   38.390904] Key type id_resolver registered
[   38.390906] Key type id_legacy registered
[   38.640999] Bluetooth: Core ver 2.17
[   38.641032] NET: Registered protocol family 31
[   38.641034] Bluetooth: HCI device and connection manager initialized
[   38.641047] Bluetooth: HCI socket layer initialized
[   38.641051] Bluetooth: L2CAP socket layer initialized
[   38.641056] Bluetooth: SCO socket layer initialized
[   38.645566] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   38.645572] Bluetooth: BNEP filters: protocol multicast
[   38.645585] Bluetooth: BNEP socket layer initialized
[   38.646759] Bluetooth: RFCOMM TTY layer initialized
[   38.646772] Bluetooth: RFCOMM socket layer initialized
[   38.646781] Bluetooth: RFCOMM ver 1.11
[   38.891714] init: cups main process (969) killed by HUP signal
[   38.891730] init: cups main process ended, respawning
[   39.984844] atl1 0000:02:00.0: irq 44 for MSI/MSI-X
[   39.984956] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
[   40.550659] init: samba-ad-dc main process (1046) terminated with status 1
[   42.459956] vboxdrv: module verification failed: signature and/or  required key missing - tainting kernel
[   42.466136] vboxdrv: Found 4 processor cores.
[   42.467571] vboxdrv: fAsync=0 offMin=0x2f6 offMax=0x2f83
[   42.467685] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   42.467687] vboxdrv: Successfully loaded version 4.3.30 (interface 0x001a000a).
[   42.679824] vboxpci: IOMMU not found (not registered)
[   43.281076] init: plymouth-upstart-bridge main process ended, respawning
[   43.288868] init: plymouth-upstart-bridge main process (1799) terminated with status 1
[   43.288885] init: plymouth-upstart-bridge main process ended, respawning
[  107.179875] usb 1-9: reset high-speed USB device number 4 using ehci-pci

Hors ligne

#24 Le 30/08/2015, à 23:20

MicP

Re : [Résolu] Sata COMRESET failed (errno=-32)

Si tu en as la possibilité, essaie de remplacer le bloc d'alimentation : Ça coûte rien (ou très peu) d'essayer, et une panne d'alimentation pourrait expliquer ces dysfonctionnement aléatoires.

Hors ligne

#25 Le 31/08/2015, à 09:27

Pingouinbricoleur

Re : [Résolu] Sata COMRESET failed (errno=-32)

Bonjour à tous,

Je n'ai pas d'alim sous la main.

Pour revenir à mon premier post :
Ce que je ne comprends pas, c'est que je ne puisse pas accéder au second disque sata par gparted. Il m'est impossible d'y avoir accès.

En tout cas un grand merci à tous ceux qui ont essayé et qui essaient de m'aider.

Hors ligne