Pages : 1
#1 Le 20/10/2015, à 17:55
- aleas12
connexion lente voir impossible en wifi sur freebox
Bonjour ,
J'ai un pc portable lenovo 54-30 intel celeron cpu n 2840 carte graphique intel bay trail os type 64 bits . je me connecte en wifi sur ma freebox .
j'ai un autre pc qui est connecté en wifi sur la même box avec win 7 et le wifi sur l'autre pc fonctionne correctement . Le wifi sur mon pc lenovo ne foctionnait plus lorsque j'ai installé ubuntu a la place du win 8 original , j'ai réussi je ne sais plus comment à capter à nouveau ma box mais le débit est à 18 mb/s et des fois il fonctionne plus pour peux que je change mon pc de place .
Voici ce qu'affiche mon terminal :
:
bash: cat/etc/lsb-release: Aucun fichier ou dossier de ce type
Bus 001 Device 007: ID 0bda:b728 Realtek Semiconductor Corp.
Bus 001 Device 006: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 005: ID 0bda:579a Realtek Semiconductor Corp.
Bus 001 Device 004: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 003: ID 062a:4101 Creative Labs
Bus 001 Device 002: ID 8087:07e6 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
hubert@hubert-Lenovo-G50-30:~$
00:00.0 Host bridge: Intel Corporation ValleyView SSA-CUnit (rev 0e)
00:02.0 VGA compatible controller: Intel Corporation ValleyView Gen7 (rev 0e)
00:13.0 SATA controller: Intel Corporation ValleyView 6-Port SATA AHCI Controller (rev 0e)
00:1a.0 Encryption controller: Intel Corporation ValleyView SEC (rev 0e)
00:1b.0 Audio device: Intel Corporation ValleyView High Definition Audio Controller (rev 0e)
00:1c.0 PCI bridge: Intel Corporation ValleyView PCI Express Root Port (rev 0e)
00:1c.2 PCI bridge: Intel Corporation ValleyView PCI Express Root Port (rev 0e)
00:1c.3 PCI bridge: Intel Corporation ValleyView PCI Express Root Port (rev 0e)
00:1d.0 USB controller: Intel Corporation ValleyView USB Enhanced Host Controller (rev 0e)
00:1f.0 ISA bridge: Intel Corporation ValleyView Power Control Unit (rev 0e)
00:1f.3 SMBus: Intel Corporation ValleyView SMBus Controller (rev 0e)
Module Size Used by
pci_stub 12622 1
vboxpci 23194 0
vboxnetadp 25670 0
vboxnetflt 27613 0
vboxdrv 339502 3 vboxnetadp,vboxnetflt,vboxpci
bnep 19624 2
rfcomm 69509 8
arc4 12608 2
snd_hda_codec_hdmi 47548 1
rtl8723be 85054 0
snd_hda_codec_conexant 23109 1
snd_hda_codec_generic 69011 1 snd_hda_codec_conexant
btcoexist 50304 1 rtl8723be
rtl8723_common 23361 1 rtl8723be
rtl_pci 26690 1 rtl8723be
rtlwifi 64255 2 rtl_pci,rtl8723be
mac80211 652777 3 rtl_pci,rtlwifi,rtl8723be
cfg80211 498458 2 mac80211,rtlwifi
binfmt_misc 17468 1
rtsx_usb_ms 18697 0
memstick 16966 1 rtsx_usb_ms
rtsx_usb_sdmmc 27787 0
uvcvideo 81073 0
videobuf2_vmalloc 13216 1 uvcvideo
videobuf2_memops 13362 1 videobuf2_vmalloc
videobuf2_core 59104 1 uvcvideo
v4l2_common 15681 1 videobuf2_core
videodev 153793 3 uvcvideo,v4l2_common,videobuf2_core
media 21903 2 uvcvideo,videodev
rtsx_usb 20987 2 rtsx_usb_sdmmc,rtsx_usb_ms
intel_rapl 18783 0
intel_powerclamp 18823 0
coretemp 13441 0
kvm 452096 0
crct10dif_pclmul 14307 0
crc32_pclmul 13133 0
ghash_clmulni_intel 13230 0
cryptd 20359 1 ghash_clmulni_intel
btusb 32497 0
bluetooth 446409 22 bnep,btusb,rfcomm
6lowpan_iphc 18702 1 bluetooth
snd_soc_rt5640 93042 0
snd_soc_rl6231 13037 1 snd_soc_rt5640
snd_soc_core 200204 1 snd_soc_rt5640
snd_compress 19200 1 snd_soc_core
snd_pcm_dmaengine 15172 1 snd_soc_core
snd_seq_midi 13564 0
snd_seq_midi_event 14899 1 snd_seq_midi
snd_rawmidi 30876 1 snd_seq_midi
snd_seq 63074 2 snd_seq_midi_event,snd_seq_midi
snd_hda_intel 30469 3
snd_hda_controller 30228 1 snd_hda_intel
joydev 17393 0
snd_hda_codec 139719 5 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep 17698 1 snd_hda_codec
serio_raw 13483 0
snd_pcm 104112 7 snd_soc_rt5640,snd_soc_core,snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller,snd_pcm_dmaengine
snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi
mei_txe 19704 0
parport_pc 32741 0
shpchp 37047 0
mei 87875 1 mei_txe
lpc_ich 21093 0
snd_timer 29562 2 snd_pcm,snd_seq
ppdev 17671 0
i915 906106 3
snd 79468 19 snd_soc_core,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_compress
drm_kms_helper 61574 1 i915
lp 17759 0
parport 42348 3 lp,ppdev,parport_pc
drm 311018 5 i915,drm_kms_helper
i2c_algo_bit 13413 1 i915
iosf_mbi 13541 0
ideapad_laptop 18278 0
sparse_keymap 13948 1 ideapad_laptop
video 20128 1 i915
dw_dmac 12835 0
dw_dmac_core 28390 1 dw_dmac
intel_smartconnect 12637 0
i2c_hid 18726 0
spi_pxa2xx_platform 23079 0
soundcore 15047 2 snd,snd_hda_codec
snd_soc_sst_acpi 13007 0
i2c_designware_platform 12979 0
i2c_designware_core 14768 1 i2c_designware_platform
8250_dw 13551 0
pwm_lpss 13214 0
mac_hid 13227 0
hid_generic 12559 0
usbhid 52616 0
hid 110426 3 i2c_hid,hid_generic,usbhid
psmouse 106767 0
r8169 71694 0
ahci 34142 2
libahci 32424 1 ahci
mii 13934 1 r8169
sdhci_acpi 13351 0
sdhci 43685 1 sdhci_acpi
Usage: iw [options] command
Options:
--debug enable netlink debugging
--version show version (3.4)
Commands:
help [command]
Print usage for all or a specific command, e.g.
"help wowlan" or "help wowlan enable".
event [-t] [-r] [-f]
Monitor events from the kernel.
-t - print timestamp
-r - print relative timstamp
-f - print full frame for auth/assoc etc.
phy
list
List all wireless devices and their capabilities.
phy <phyname> info
Show capabilities for the specified wireless device.
dev
List all network interfaces for wireless hardware.
dev <devname> info
Show information for this interface.
dev <devname> del
Remove this virtual interface
dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
Add a new virtual interface with the given configuration.
Valid interface types are: managed, ibss, monitor, mesh, wds.
The flags are only used for monitor interfaces, valid flags are:
none: no special flags
fcsfail: show frames with FCS errors
control: show control frames
otherbss: show frames from other BSSes
cook: use cooked mode
The mesh_id is used only for mesh mode.
dev <devname> ibss join <SSID> <freq in MHz> [HT20|HT40+|HT40-|NOHT] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
Join the IBSS cell with the given SSID, if it doesn't exist create
it on the given frequency. When fixed frequency is requested, don't
join/create a cell on a different frequency. When a fixed BSSID is
requested use that BSSID and do not adopt another cell's BSSID even
if it has higher TSF and the same SSID. If an IBSS is created, create
it with the specified basic-rates, multicast-rate and beacon-interval.
dev <devname> ibss leave
Leave the current IBSS cell.
dev <devname> station dump
List all stations known, e.g. the AP on managed interfaces
dev <devname> station set <MAC address> vlan <ifindex>
Set an AP VLAN for this station.
dev <devname> station set <MAC address> plink_action <open|block>
Set mesh peer link action for this station (peer).
dev <devname> station del <MAC address>
Remove the given station entry (use with caution!)
dev <devname> station get <MAC address>
Get information for a specific station.
dev <devname> survey dump
List all gathered channel survey data
dev <devname> mesh leave
Leave a mesh.
dev <devname> mesh join <mesh ID> [mcast-rate <rate in Mbps>] [<param>=<value>]*
Join a mesh with the given mesh ID with mcast-rate and mesh parameters.
dev <devname> mpath dump
List known mesh paths.
dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
Set an existing mesh path's next hop.
dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
Create a new mesh path (instead of relying on automatic discovery).
dev <devname> mpath del <MAC address>
Remove the mesh path to the given node.
dev <devname> mpath get <MAC address>
Get information on mesh path to the given node.
dev <devname> scan [-u] [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
Scan on the given frequencies and probe for the given SSIDs
(or wildcard if not given) unless passive scanning is requested.
If -u is specified print unknown data in the scan results.
Specified (vendor) IEs must be well-formed.
dev <devname> scan trigger [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
Trigger a scan on the given frequencies with probing for the given
SSIDs (or wildcard if not given) unless passive scanning is requested.
dev <devname> scan dump [-u]
Dump the current scan results. If -u is specified, print unknown
data in scan results.
reg get
Print out the kernel's current regulatory domain information.
reg set <ISO/IEC 3166-1 alpha2>
Notify the kernel about the current regulatory domain.
dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]
Join the network with the given SSID (and frequency, BSSID).
With -w, wait for the connect to finish or fail.
dev <devname> disconnect
Disconnect from the current network.
dev <devname> link
Print information about the current link, if any.
dev <devname> offchannel <freq> <duration>
Leave operating channel and go to the given channel for a while.
dev <devname> cqm rssi <threshold|off> [<hysteresis>]
Set connection quality monitor RSSI threshold.
phy <phyname> wowlan show
Show WoWLAN status.
phy <phyname> wowlan disable
Disable WoWLAN.
phy <phyname> wowlan enable [any] [disconnect] [magic-packet] [gtk-rekey-failure] [eap-identity-request] [4way-handshake] [rfkill-release] [patterns <pattern>*]
Enable WoWLAN with the given triggers.
Each pattern is given as a bytestring with '-' in places where any byte
may be present, e.g. 00:11:22:-:44 will match 00:11:22:33:44 and
00:11:22:33:ff:44 etc.
dev <devname> roc start <freq> <time>
phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
Set a bitmap of allowed antennas to use for TX and RX.
The driver may reject antenna configurations it cannot support.
dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
Specify transmit power level and setting type.
phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
Specify transmit power level and setting type.
phy <phyname> set distance <distance>
Set appropriate coverage class for given link distance in meters.
Valid values: 0 - 114750
phy <phyname> set coverage <coverage class>
Set coverage class (1 for every 3 usec of air propagation time).
Valid values: 0 - 255.
phy <phyname> set netns <pid>
Put this wireless device into a different network namespace
phy <phyname> set rts <rts threshold|off>
Set rts threshold.
phy <phyname> set frag <fragmentation threshold|off>
Set fragmentation threshold.
dev <devname> set channel <channel> [HT20|HT40+|HT40-]
phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
dev <devname> set freq <freq> [HT20|HT40+|HT40-]
phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
Set frequency/channel the hardware is using, including HT
configuration.
phy <phyname> set name <new name>
Rename this wireless device.
dev <devname> set peer <MAC address>
Set interface WDS peer.
dev <devname> set noack_map <map>
Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)
dev <devname> set 4addr <on|off>
Set interface 4addr (WDS) mode.
dev <devname> set type <type>
Set interface type/mode.
Valid interface types are: managed, ibss, monitor, mesh, wds.
dev <devname> set meshid <meshid>
dev <devname> set monitor <flag>*
Set monitor flags. Valid flags are:
none: no special flags
fcsfail: show frames with FCS errors
control: show control frames
otherbss: show frames from other BSSes
cook: use cooked mode
dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
Set mesh parameter (run command without any to see available ones).
dev <devname> set power_save <on|off>
Set power save state to on or off.
dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
Sets up the specified rate masks.
Not passing any arguments would clear the existing mask (if any).
dev <devname> get mesh_param [<param>]
Retrieve mesh parameter (run command without any to see available ones).
dev <devname> get power_save <param>
Retrieve power save state.
You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)
Do NOT screenscrape this tool, we don't consider its output stable.
dev <devname> set freq <freq> [HT20|HT40+|HT40-]
phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
Set frequency/channel the hardware is using, including HT
configuration.
phy <phyname> set name <new name>
Rename this wireless device.
dev <devname> set peer <MAC address>
Set interface WDS peer.
dev <devname> set noack_map <map>
Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)
dev <devname> set 4addr <on|off>
Set interface 4addr (WDS) mode.
dev <devname> set type <type>
Set interface type/mode.
Valid interface types are: managed, ibss, monitor, mesh, wds.
dev <devname> set meshid <meshid>
dev <devname> set monitor <flag>*
Set monitor flags. Valid flags are:
none: no special flags
fcsfail: show frames with FCS errors
control: show control frames
otherbss: show frames from other BSSes
cook: use cooked mode
dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
Set mesh parameter (run command without any to see available ones).
dev <devname> set power_save <on|off>
Set power save state to on or off.
dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
Sets up the specified rate masks.
Not passing any arguments would clear the existing mask (if any).
dev <devname> get mesh_param [<param>]
Retrieve mesh parameter (run command without any to see available ones).
dev <devname> get power_save <param>
Retrieve power save state.
You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)
Do NOT screenscrape this tool, we don't consider its output stable.
hubert@hubert-Lenovo-G50-30:~$ iw list scan
Usage: iw [options] command
Options:
--debug enable netlink debugging
--version show version (3.4)
Commands:
help [command]
Print usage for all or a specific command, e.g.
"help wowlan" or "help wowlan enable".
event [-t] [-r] [-f]
Monitor events from the kernel.
-t - print timestamp
-r - print relative timstamp
-f - print full frame for auth/assoc etc.
phy
list
List all wireless devices and their capabilities.
phy <phyname> info
Show capabilities for the specified wireless device.
dev
List all network interfaces for wireless hardware.
dev <devname> info
Show information for this interface.
dev <devname> del
Remove this virtual interface
dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
Add a new virtual interface with the given configuration.
Valid interface types are: managed, ibss, monitor, mesh, wds.
The flags are only used for monitor interfaces, valid flags are:
none: no special flags
fcsfail: show frames with FCS errors
control: show control frames
otherbss: show frames from other BSSes
cook: use cooked mode
The mesh_id is used only for mesh mode.
dev <devname> ibss join <SSID> <freq in MHz> [HT20|HT40+|HT40-|NOHT] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
Join the IBSS cell with the given SSID, if it doesn't exist create
it on the given frequency. When fixed frequency is requested, don't
join/create a cell on a different frequency. When a fixed BSSID is
requested use that BSSID and do not adopt another cell's BSSID even
if it has higher TSF and the same SSID. If an IBSS is created, create
it with the specified basic-rates, multicast-rate and beacon-interval.
dev <devname> ibss leave
Leave the current IBSS cell.
dev <devname> station dump
List all stations known, e.g. the AP on managed interfaces
dev <devname> station set <MAC address> vlan <ifindex>
Set an AP VLAN for this station.
dev <devname> station set <MAC address> plink_action <open|block>
Set mesh peer link action for this station (peer).
dev <devname> station del <MAC address>
Remove the given station entry (use with caution!)
dev <devname> station get <MAC address>
Get information for a specific station.
dev <devname> survey dump
List all gathered channel survey data
dev <devname> mesh leave
Leave a mesh.
dev <devname> mesh join <mesh ID> [mcast-rate <rate in Mbps>] [<param>=<value>]*
Join a mesh with the given mesh ID with mcast-rate and mesh parameters.
dev <devname> mpath dump
List known mesh paths.
dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
Set an existing mesh path's next hop.
dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
Create a new mesh path (instead of relying on automatic discovery).
dev <devname> mpath del <MAC address>
Remove the mesh path to the given node.
dev <devname> mpath get <MAC address>
Get information on mesh path to the given node.
dev <devname> scan [-u] [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
Scan on the given frequencies and probe for the given SSIDs
(or wildcard if not given) unless passive scanning is requested.
If -u is specified print unknown data in the scan results.
Specified (vendor) IEs must be well-formed.
dev <devname> scan trigger [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
Trigger a scan on the given frequencies with probing for the given
SSIDs (or wildcard if not given) unless passive scanning is requested.
dev <devname> scan dump [-u]
Dump the current scan results. If -u is specified, print unknown
data in scan results.
reg get
Print out the kernel's current regulatory domain information.
reg set <ISO/IEC 3166-1 alpha2>
Notify the kernel about the current regulatory domain.
dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]
Join the network with the given SSID (and frequency, BSSID).
With -w, wait for the connect to finish or fail.
dev <devname> disconnect
Disconnect from the current network.
dev <devname> link
Print information about the current link, if any.
dev <devname> offchannel <freq> <duration>
Leave operating channel and go to the given channel for a while.
dev <devname> cqm rssi <threshold|off> [<hysteresis>]
Set connection quality monitor RSSI threshold.
phy <phyname> wowlan show
Show WoWLAN status.
phy <phyname> wowlan disable
Disable WoWLAN.
phy <phyname> wowlan enable [any] [disconnect] [magic-packet] [gtk-rekey-failure] [eap-identity-request] [4way-handshake] [rfkill-release] [patterns <pattern>*]
Enable WoWLAN with the given triggers.
Each pattern is given as a bytestring with '-' in places where any byte
may be present, e.g. 00:11:22:-:44 will match 00:11:22:33:44 and
00:11:22:33:ff:44 etc.
dev <devname> roc start <freq> <time>
phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
Set a bitmap of allowed antennas to use for TX and RX.
The driver may reject antenna configurations it cannot support.
dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
Specify transmit power level and setting type.
phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
Specify transmit power level and setting type.
phy <phyname> set distance <distance>
Set appropriate coverage class for given link distance in meters.
Valid values: 0 - 114750
phy <phyname> set coverage <coverage class>
Set coverage class (1 for every 3 usec of air propagation time).
Valid values: 0 - 255.
phy <phyname> set netns <pid>
Put this wireless device into a different network namespace
phy <phyname> set rts <rts threshold|off>
Set rts threshold.
phy <phyname> set frag <fragmentation threshold|off>
Set fragmentation threshold.
dev <devname> set channel <channel> [HT20|HT40+|HT40-]
phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
dev <devname> set freq <freq> [HT20|HT40+|HT40-]
phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
Set frequency/channel the hardware is using, including HT
configuration.
phy <phyname> set name <new name>
Rename this wireless device.
dev <devname> set peer <MAC address>
Set interface WDS peer.
dev <devname> set noack_map <map>
Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)
dev <devname> set 4addr <on|off>
Set interface 4addr (WDS) mode.
dev <devname> set type <type>
Set interface type/mode.
Valid interface types are: managed, ibss, monitor, mesh, wds.
dev <devname> set meshid <meshid>
dev <devname> set monitor <flag>*
Set monitor flags. Valid flags are:
none: no special flags
fcsfail: show frames with FCS errors
control: show control frames
otherbss: show frames from other BSSes
cook: use cooked mode
dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
Set mesh parameter (run command without any to see available ones).
dev <devname> set power_save <on|off>
Set power save state to on or off.
dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
Sets up the specified rate masks.
Not passing any arguments would clear the existing mask (if any).
dev <devname> get mesh_param [<param>]
Retrieve mesh parameter (run command without any to see available ones).
dev <devname> get power_save <param>
Retrieve power save state.
You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)
Do NOT screenscrape this tool, we don't consider its output stable.
hubert@hubert-Lenovo-G50-30:~$ sudo iwlist scan
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 16:EF:08:09:85:28
Channel:7
Frequency:2.442 GHz (Channel 7)
Quality=70/70 Signal level=-12 dBm
Encryption key:on
ESSID:"freebox_hubert"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000021ef1eb26c1
Extra: Last beacon: 112ms ago
IE: Unknown: 000E66726565626F785F687562657274
IE: Unknown: 010882848B961224486C
IE: Unknown: 030107
IE: Unknown: 2A0104
IE: Unknown: 32040C183060
IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: 3D1607000700000000000000000000000000000000000000
IE: Unknown: 3E0100
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: 7F0101
IE: Unknown: DD07000C4300000000
IE: Unknown: DD1E00904C336E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: DD1A00904C3407000700000000000000000000000000000000000000
Cell 02 - Address: 16:EF:08:09:85:29
Channel:7
Frequency:2.442 GHz (Channel 7)
Quality=70/70 Signal level=-10 dBm
Encryption key:on
ESSID:""
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000021ef2097a5d
Extra: Last beacon: 112ms ago
IE: Unknown: 0000
IE: Unknown: 010882848B961224486C
IE: Unknown: 030107
IE: Unknown: 32040C183060
IE: Unknown: 33082001020304050607
IE: Unknown: 33082105060708090A0B
IE: Unknown: 050400010000
IE: Unknown: 2A0104
IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: 3D1607000700000000000000000000000000000000000000
IE: Unknown: 7F0101
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: 0B05030019127A
IE: Unknown: DD1E00904C336E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: DD1A00904C3407000700000000000000000000000000000000000000
IE: Unknown: DD07000C4300000000
Cell 03 - Address: 16:EF:08:09:85:2A
Channel:7
Frequency:2.442 GHz (Channel 7)
Quality=70/70 Signal level=-12 dBm
Encryption key:off
ESSID:"FreeWifi"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000021ef1eb3066
Extra: Last beacon: 108ms ago
IE: Unknown: 00084672656557696669
IE: Unknown: 010882848B961224486C
IE: Unknown: 030107
IE: Unknown: 2A0104
IE: Unknown: 32040C183060
IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: 3D1607000700000000000000000000000000000000000000
IE: Unknown: 3E0100
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: 7F0101
IE: Unknown: DD07000C4300000000
IE: Unknown: DD1E00904C336E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: DD1A00904C3407000700000000000000000000000000000000000000
Cell 04 - Address: 16:EF:08:09:85:2B
Channel:7
Frequency:2.442 GHz (Channel 7)
Quality=70/70 Signal level=-12 dBm
Encryption key:on
ESSID:"FreeWifi_secure"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000021ef1eb39db
Extra: Last beacon: 104ms ago
IE: Unknown: 000F46726565576966695F736563757265
IE: Unknown: 010882848B961224486C
IE: Unknown: 030107
IE: Unknown: 2A0104
IE: Unknown: 32040C183060
IE: Unknown: 2D1A6E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: 3D1607000700000000000000000000000000000000000000
IE: Unknown: 3E0100
IE: WPA Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : 802.1x
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: 7F0101
IE: Unknown: DD07000C4300000000
IE: Unknown: DD1E00904C336E1017FFFF000001000000000000000000000000000000000000
IE: Unknown: DD1A00904C3407000700000000000000000000000000000000000000
lo Interface doesn't support scanning.
hubert@hubert-Lenovo-G50-30:~$ uname_r_m
uname_r_m : commande introuvable
hubert@hubert-Lenovo-G50-30:~$ uname-r-m
uname-r-m : commande introuvable
hubert@hubert-Lenovo-G50-30:~$ cat/etc/network/interfaces
bash: cat/etc/network/interfaces: Aucun fichier ou dossier de ce type
hubert@hubert-Lenovo-G50-30:~$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: 68:F7:28:5F:07:1B
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
- Device: wlan0 [freebox_hubert 1] --------------------------------------------
Type: 802.11 WiFi
Driver: rtl8723be
State: connected
Default: yes
HW Address: 2C:33:7A:0C:1D:B9
Capabilities:
Speed: 18 Mb/s
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points (* = current AP)
FreeWifi_secure: Infra, 16:EF:08:09:85:2B, Freq 2442 MHz, Rate 54 Mb/s, Strength 100 WPA Enterprise
FreeWifi: Infra, 16:EF:08:09:85:2A, Freq 2442 MHz, Rate 54 Mb/s, Strength 100
*freebox_hubert: Infra, 16:EF:08:09:85:28, Freq 2442 MHz, Rate 54 Mb/s, Strength 100 WEP
IPv4 Settings:
Address: 192.168.0.12
Prefix: 24 (255.255.255.0)
Gateway: 192.168.0.254
DNS: 212.27.40.240
DNS: 212.27.40.241J'ai mis toutes les réponses que j'ai pus avoir sur mon terminal , la maladie est-elle grave docteur !!.
Merci de votre aide car j'aimerai pouvoir continuer avec ubuntu .
aleas12
Hors ligne
#2 Le 20/10/2015, à 21:34
- Braun
Re : connexion lente voir impossible en wifi sur freebox
Bonsoir,
Ne serait-ce pas une question de clef WPA, j'ai vu passer un topic du genre : si tu ne précises pas le bon type de WPA le système s’emmêle tel l'âne de Buridan.
Hors ligne
#3 Le 24/10/2015, à 09:49
- aleas12
Re : connexion lente voir impossible en wifi sur freebox
Bonjour ,
j'ai une clé wep pour accès a ma box , et elle est bien configurée , je pense qu'il y a beaucoup de renseignement dans les ligne de programmation de mon terminal mais pour moi c'est pas du patois local alors je comprend rien !!????
Merci
Hubert
Hors ligne
#4 Le 27/10/2015, à 13:14
- bushidatra
Re : connexion lente voir impossible en wifi sur freebox
bonjour ,
avez vous accès a internet quand vous etes connecté au reseau wifi de votre box ?
si non , vous pouvez tester ca :
ouvrir un terminal ,
sudo gedit /etc/resolv.confrajouter :
nameserver 192.168.0.254 enregistrer et fermer
le prb : dès qu' on repasser sur une configuration box "classique" on doit remodifier /etc/resolv.conf avec nameserver 192.168.1.1
la solution ci dessus ne resoudra pas les prb de déconnexion du wifi
Hors ligne
#5 Le 27/10/2015, à 13:16
- cqfd93
Re : connexion lente voir impossible en wifi sur freebox
Bonjour,
Pour les freebox (en tout cas jusqu'à la v5), la passerelle est 192.168.0.254.
Pour le wifi, il est largement préférable d'utiliser une clé WPA (ça se paramètre sur l'interface de gestion). Vérifier aussi que le mode routeur et le DHCP sont correctement paramétrés.
L'idéal serait de faire tous ces paramétrages en étant connecté en filaire. On peut t'aider à apprendre ce patois 
− cqfd93 −
Hors ligne
#6 Le 27/10/2015, à 14:52
- Braun
Re : connexion lente voir impossible en wifi sur freebox
cqfd93 a écrit :
L'idéal serait de faire tous ces paramétrages en étant connecté en filaire.
+1
Hors ligne
Pages : 1