#26 Le 17/02/2017, à 13:55
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
Je ne sais que te dire.
La première des choses va être d mettre a jour le firmware car tu as la version CC46 et c'est la version CC49 qu'il faudrait. Je n'ai pas regardé ce qu'elle corrige.
http://knowledge.seagate.com/articles/e … Q/207931en
http://knowledge.seagate.com/articles/e … Q/213891en
c'est donc ici http://www.seagate.com/staticfiles/supp … L-CC49.iso
al'aide de ce document si tu n'as pas un Windows http://knowledge.seagate.com/articles/e … Q/004301en
sinon a l'aide de http://knowledge.seagate.com/articles/e … Q/004989en
Dernière modification par Bougron (Le 17/02/2017, à 13:58)
Hors ligne
#27 Le 19/02/2017, à 13:43
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Il a bien fait l'update, mais ça ne règle rien...
Du coup j'ai deux questions :
- Est-ce que c'est impossible que ça soit malgré tout un problème physique du disque dur ?
- Comment est-ce que je peux faire pour lancer un chkdsk sur ce disque ? (avec un bootCD par exemple ou je sais pas)
Merci encore !
Hors ligne
#28 Le 19/02/2017, à 14:11
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
Peux-tu refaire les commandes du post 16
puis donner le retour de
dmesg | grep sdb
ainsi qu'un nouveau smartctl
Mais je crains que le disque soit fichu.
Dernière modification par Bougron (Le 19/02/2017, à 14:13)
Hors ligne
#29 Le 19/02/2017, à 14:22
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Alors :
[ 7.912309] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 7.912392] sd 1:0:0:0: [sdb] Write Protect is off
[ 7.912394] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 7.912427] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.142887] sd 1:0:0:0: [sdb] tag#10 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.142891] sd 1:0:0:0: [sdb] tag#10 Sense Key : Illegal Request [current]
[ 8.142894] sd 1:0:0:0: [sdb] tag#10 Add. Sense: Unaligned write command
[ 8.142898] sd 1:0:0:0: [sdb] tag#10 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.142901] blk_update_request: I/O error, dev sdb, sector 0
[ 8.142906] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.214789] sd 1:0:0:0: [sdb] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.214793] sd 1:0:0:0: [sdb] tag#16 Sense Key : Illegal Request [current]
[ 8.214797] sd 1:0:0:0: [sdb] tag#16 Add. Sense: Unaligned write command
[ 8.214801] sd 1:0:0:0: [sdb] tag#16 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.214803] blk_update_request: I/O error, dev sdb, sector 0
[ 8.214808] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.286755] sd 1:0:0:0: [sdb] tag#22 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.286758] sd 1:0:0:0: [sdb] tag#22 Sense Key : Illegal Request [current]
[ 8.286762] sd 1:0:0:0: [sdb] tag#22 Add. Sense: Unaligned write command
[ 8.286766] sd 1:0:0:0: [sdb] tag#22 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.286768] blk_update_request: I/O error, dev sdb, sector 0
[ 8.286774] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.358921] sd 1:0:0:0: [sdb] tag#28 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.358925] sd 1:0:0:0: [sdb] tag#28 Sense Key : Illegal Request [current]
[ 8.358929] sd 1:0:0:0: [sdb] tag#28 Add. Sense: Unaligned write command
[ 8.358933] sd 1:0:0:0: [sdb] tag#28 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.358935] blk_update_request: I/O error, dev sdb, sector 0
[ 8.358940] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.430876] sd 1:0:0:0: [sdb] tag#3 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.430879] sd 1:0:0:0: [sdb] tag#3 Sense Key : Illegal Request [current]
[ 8.430882] sd 1:0:0:0: [sdb] tag#3 Add. Sense: Unaligned write command
[ 8.430885] sd 1:0:0:0: [sdb] tag#3 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.430887] blk_update_request: I/O error, dev sdb, sector 0
[ 8.430891] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.502828] sd 1:0:0:0: [sdb] tag#9 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.502831] sd 1:0:0:0: [sdb] tag#9 Sense Key : Illegal Request [current]
[ 8.502834] sd 1:0:0:0: [sdb] tag#9 Add. Sense: Unaligned write command
[ 8.502837] sd 1:0:0:0: [sdb] tag#9 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.502839] blk_update_request: I/O error, dev sdb, sector 0
[ 8.502843] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.574858] sd 1:0:0:0: [sdb] tag#15 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.574861] sd 1:0:0:0: [sdb] tag#15 Sense Key : Illegal Request [current]
[ 8.574864] sd 1:0:0:0: [sdb] tag#15 Add. Sense: Unaligned write command
[ 8.574867] sd 1:0:0:0: [sdb] tag#15 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.574869] blk_update_request: I/O error, dev sdb, sector 0
[ 8.574873] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.574892] Dev sdb: unable to read RDB block 0
[ 8.646821] sd 1:0:0:0: [sdb] tag#21 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.646825] sd 1:0:0:0: [sdb] tag#21 Sense Key : Illegal Request [current]
[ 8.646829] sd 1:0:0:0: [sdb] tag#21 Add. Sense: Unaligned write command
[ 8.646833] sd 1:0:0:0: [sdb] tag#21 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.646835] blk_update_request: I/O error, dev sdb, sector 0
[ 8.646840] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.718867] sd 1:0:0:0: [sdb] tag#27 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.718870] sd 1:0:0:0: [sdb] tag#27 Sense Key : Illegal Request [current]
[ 8.718873] sd 1:0:0:0: [sdb] tag#27 Add. Sense: Unaligned write command
[ 8.718877] sd 1:0:0:0: [sdb] tag#27 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 8.718878] blk_update_request: I/O error, dev sdb, sector 0
[ 8.718883] Buffer I/O error on dev sdb, logical block 0, async page read
[ 8.790834] sd 1:0:0:0: [sdb] tag#2 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 8.790838] sd 1:0:0:0: [sdb] tag#2 Sense Key : Illegal Request [current]
[ 8.790842] sd 1:0:0:0: [sdb] tag#2 Add. Sense: Unaligned write command
[ 8.790846] sd 1:0:0:0: [sdb] tag#2 CDB: Read(10) 28 00 00 00 00 18 00 00 08 00
[ 8.790848] blk_update_request: I/O error, dev sdb, sector 24
[ 8.790853] Buffer I/O error on dev sdb, logical block 3, async page read
[ 8.934842] sdb: unable to read partition table
[ 8.935240] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 8.964244] sdb: detected capacity change from 0 to 500107862016
[ 24.022929] sd 1:0:0:0: [sdb] tag#20 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 24.022932] sd 1:0:0:0: [sdb] tag#20 Sense Key : Illegal Request [current]
[ 24.022935] sd 1:0:0:0: [sdb] tag#20 Add. Sense: Unaligned write command
[ 24.022938] sd 1:0:0:0: [sdb] tag#20 CDB: Read(10) 28 00 3a 38 5f 80 00 00 08 00
[ 24.022940] blk_update_request: I/O error, dev sdb, sector 976772992
[ 24.095094] sd 1:0:0:0: [sdb] tag#20 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 24.095098] sd 1:0:0:0: [sdb] tag#20 Sense Key : Illegal Request [current]
[ 24.095102] sd 1:0:0:0: [sdb] tag#20 Add. Sense: Unaligned write command
[ 24.095107] sd 1:0:0:0: [sdb] tag#20 CDB: Read(10) 28 00 3a 38 5f 80 00 00 08 00
[ 24.095110] blk_update_request: I/O error, dev sdb, sector 976772992
[ 24.095117] Buffer I/O error on dev sdb, logical block 122096624, async page read
[ 407.554127] sd 1:0:0:0: [sdb] tag#3 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 407.554132] sd 1:0:0:0: [sdb] tag#3 Sense Key : Illegal Request [current]
[ 407.554136] sd 1:0:0:0: [sdb] tag#3 Add. Sense: Unaligned write command
[ 407.554141] sd 1:0:0:0: [sdb] tag#3 CDB: Read(10) 28 00 00 00 03 e8 00 00 08 00
[ 407.554143] blk_update_request: I/O error, dev sdb, sector 1000
[ 407.626050] sd 1:0:0:0: [sdb] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 407.626053] sd 1:0:0:0: [sdb] tag#1 Sense Key : Illegal Request [current]
[ 407.626057] sd 1:0:0:0: [sdb] tag#1 Add. Sense: Unaligned write command
[ 407.626061] sd 1:0:0:0: [sdb] tag#1 CDB: Read(10) 28 00 00 00 03 e8 00 00 08 00
[ 407.626063] blk_update_request: I/O error, dev sdb, sector 1000
[ 407.626069] Buffer I/O error on dev sdb, logical block 125, async page read
[ 419.486389] sd 1:0:0:0: [sdb] tag#16 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 419.486394] sd 1:0:0:0: [sdb] tag#16 Sense Key : Illegal Request [current]
[ 419.486398] sd 1:0:0:0: [sdb] tag#16 Add. Sense: Unaligned write command
[ 419.486403] sd 1:0:0:0: [sdb] tag#16 CDB: Read(10) 28 00 00 00 27 10 00 00 08 00
[ 419.486406] blk_update_request: I/O error, dev sdb, sector 10000
[ 419.558351] sd 1:0:0:0: [sdb] tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 419.558355] sd 1:0:0:0: [sdb] tag#4 Sense Key : Illegal Request [current]
[ 419.558359] sd 1:0:0:0: [sdb] tag#4 Add. Sense: Unaligned write command
[ 419.558363] sd 1:0:0:0: [sdb] tag#4 CDB: Read(10) 28 00 00 00 27 10 00 00 08 00
[ 419.558365] blk_update_request: I/O error, dev sdb, sector 10000
[ 419.558371] Buffer I/O error on dev sdb, logical block 1250, async page read
[ 422.498377] sd 1:0:0:0: [sdb] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 422.498381] sd 1:0:0:0: [sdb] tag#17 Sense Key : Illegal Request [current]
[ 422.498385] sd 1:0:0:0: [sdb] tag#17 Add. Sense: Unaligned write command
[ 422.498390] sd 1:0:0:0: [sdb] tag#17 CDB: Read(10) 28 00 00 01 86 a0 00 00 08 00
[ 422.498393] blk_update_request: I/O error, dev sdb, sector 100000
[ 422.570478] sd 1:0:0:0: [sdb] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 422.570482] sd 1:0:0:0: [sdb] tag#17 Sense Key : Illegal Request [current]
[ 422.570486] sd 1:0:0:0: [sdb] tag#17 Add. Sense: Unaligned write command
[ 422.570490] sd 1:0:0:0: [sdb] tag#17 CDB: Read(10) 28 00 00 01 86 a0 00 00 08 00
[ 422.570493] blk_update_request: I/O error, dev sdb, sector 100000
[ 422.570498] Buffer I/O error on dev sdb, logical block 12500, async page read
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-37-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3500418AS
Serial Number: 9VMXJJF9
LU WWN Device Id: 5 000c50 02d9fb546
Firmware Version: CC49
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Feb 19 13:24:44 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 193796753
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2161
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - 31084865
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5329
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1077
183 Runtime_Bad_Block 0x0032 093 093 000 Old_age Always - 7
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 042 000 Old_age Always - 2332202894297
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 073 053 045 Old_age Always - 27 (Min/Max 25/27)
194 Temperature_Celsius 0x0022 027 047 000 Old_age Always - 27 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 037 027 000 Old_age Always - 193796753
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 032 000 Old_age Always - 10942
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8161 (155 24 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 638528687
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 694687685
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 5295 hours (220 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 00 00 00 00 00 ff 00:23:08.745 NOP [Abort queued commands]
b0 d4 00 81 4f c2 e0 00 00:22:54.830 SMART EXECUTE OFF-LINE IMMEDIATE
00 00 00 00 00 00 00 04 00:22:54.811 NOP [Abort queued commands]
b0 d0 04 00 4f c2 e0 00 00:22:54.748 SMART READ DATA
00 00 00 00 00 00 00 04 00:22:51.997 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5329 -
# 2 Short captive Interrupted (host reset) 80% 5295 -
# 3 Short offline Completed without error 00% 3147 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Pour les commandes du post 16 ça me donne les mêmes résultats...
Fichu ! Mince alors... Qu'est-ce qui te fait dire ça ?
Dernière modification par Pascal32 (Le 19/02/2017, à 14:48)
Hors ligne
#30 Le 20/02/2017, à 22:25
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonsoir.
Il existe une autre possibilité que j'entrevois au vu de ce résultat
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5329 -
# 2 Short captive Interrupted (host reset) 80% 5295 -
# 3 Short offline Completed without error 00% 3147 -
A 5295 heures de fonctionnement, le test n° 2 a été lancé en mode captif. Il a été tué et depuis ce moment, le firmware du disque interdit qu'il soit utilisé pour un fonctionnement applicatif.
Dans le dmesg aucun secteur n'est lisible et pourtant le short offline fonctionne encore actuellement
Certainement une commande short test à relancer pour qu'elle se finisse
je ne connais pas trop la codif.
Dernière modification par Bougron (Le 20/02/2017, à 22:27)
Hors ligne
#31 Le 20/02/2017, à 23:01
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Salut .
J'ai switché les branchements sans toucher à ceux de la carte mère (autrement dit : je n'ai pas switché les petits câbles rouges mais j'ai juste interchangé ceux plus longs et noirs - c'est bien ça ?) mais ça n'a rien changé du tout. Toujours les mêmes erreurs...
Bonsoir.
En relisant cela, j'ai l'impression que tu as permuté les câbles de l'alimentation électrique..
Permutes donc les petits câbles rouges auprès des disques sans toucher au branchement sur la carte mère.
Dernière modification par Bougron (Le 20/02/2017, à 23:24)
Hors ligne
#32 Le 22/02/2017, à 12:50
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonsoir.
Il existe une autre possibilité que j'entrevois au vu de ce résultatSMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5329 - # 2 Short captive Interrupted (host reset) 80% 5295 - # 3 Short offline Completed without error 00% 3147 -
A 5295 heures de fonctionnement, le test n° 2 a été lancé en mode captif. Il a été tué et depuis ce moment, le firmware du disque interdit qu'il soit utilisé pour un fonctionnement applicatif.
Dans le dmesg aucun secteur n'est lisible et pourtant le short offline fonctionne encore actuellementCertainement une commande short test à relancer pour qu'elle se finisse
je ne connais pas trop la codif.
J'ai permuté les deux câbles rouges mais ça ne change rien.
Que veux-tu dire par "relancer une commande short test" ? J'ai fait quelques recherches mais n'ai pas bien compris à quoi ça faisait référence. Aux test pratiqués avec smartctl ?
Hors ligne
#33 Le 22/02/2017, à 13:54
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
On va donc dire que ce n'est pas un problème de câble ni de carte mère mais bien du disque.
Cependant, il y a une chose qui me surprend
On voit le moment du dernier smartctl a 5329 heures disant que tout est OK
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5329 -
On voit aussi le moment ou cela a cessé d'être utilisé.
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5329
C'est la même heure. Depuis on ne peut plus y accéder applicativement
D'où l'idée de voir si tu pouvais relancer un test smarctl
Hors ligne
#34 Le 27/02/2017, à 15:42
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Hello
J'ai relancé le test smartctcl et ça me donne ça :
sudo smartctl -s on -a /dev/sdb
[sudo] Mot de passe de :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST500DM002-1BD142
Serial Number: Z3TTQNM3
LU WWN Device Id: 5 000c50 065517d16
Firmware Version: KC47
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Feb 27 14:41:48 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 101 099 006 Pre-fail Always - 3285256
3 Spin_Up_Time 0x0003 100 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 116
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 063 060 030 Pre-fail Always - 2466237
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 93
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 81
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 078 060 045 Old_age Always - 22 (Min/Max 20/22)
194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 054 039 000 Old_age Always - 3285256
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 94h+47m+03.181s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2878402434
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3361877967
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Dernière modification par Pascal32 (Le 27/02/2017, à 15:43)
Hors ligne
#35 Le 27/02/2017, à 15:58
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
Je ne suis pas certain que tu ais fait le smarctl du bon disque
Peux-tu aussi faire les commandes
sudo blkid
sudo smartctl -s on -a /dev/sda
Dernière modification par Bougron (Le 27/02/2017, à 15:58)
Hors ligne
#36 Le 28/02/2017, à 10:35
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Ah ! Oui pardon, j'avais pas pensé qu'intervertir les câbles changeait les noms des DD.
Du coup :
sudo smartctl -s on -a /dev/sda
[sudo] Mot de passe :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3500418AS
Serial Number: 9VMXJJF9
LU WWN Device Id: 5 000c50 02d9fb546
Firmware Version: CC49
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Feb 28 09:32:49 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 193796753
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2183
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - 31086207
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5355
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1088
183 Runtime_Bad_Block 0x0032 093 093 000 Old_age Always - 7
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 042 000 Old_age Always - 2332202894297
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 079 053 045 Old_age Always - 21 (Min/Max 18/21)
194 Temperature_Celsius 0x0022 021 047 000 Old_age Always - 21 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 036 027 000 Old_age Always - 193796753
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 032 000 Old_age Always - 10942
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8224 (22 96 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 638528687
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 694697474
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 5295 hours (220 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 00 00 00 00 00 ff 00:23:08.745 NOP [Abort queued commands]
b0 d4 00 81 4f c2 e0 00 00:22:54.830 SMART EXECUTE OFF-LINE IMMEDIATE
00 00 00 00 00 00 00 04 00:22:54.811 NOP [Abort queued commands]
b0 d0 04 00 4f c2 e0 00 00:22:54.748 SMART READ DATA
00 00 00 00 00 00 00 04 00:22:51.997 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5329 -
# 2 Short captive Interrupted (host reset) 80% 5295 -
# 3 Short offline Completed without error 00% 3147 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo blkid
/dev/sdb1: UUID="958c2586-2101-4d21-b4df-8f21c233dfac" TYPE="ext4" PARTUUID="0fc98e8e-01"
/dev/dm-0: UUID="4352ebd1-cfb1-460c-87ab-bcd4d52a2576" TYPE="swap"
/dev/sdb5: UUID="ef8752df-5bce-483c-9091-9395ed5ac43b" TYPE="swap" PARTUUID="0fc98e8e-05"
Hors ligne
#37 Le 28/02/2017, à 15:32
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
Il faut vraiment que je tire au clair ce que cache ce message
Error 1 occurred at disk power-on lifetime: 5295 hours (220 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
En attendant, peux-tu faire ces commandes
sudo smartctl -t short /dev/sda
sudo smartctl -l selftest /dev/sda
et si cela marche
sudo smartctl -t long /dev/sda
sudo smartctl -l selftest /dev/sda
sudo smartctl -a /dev/sda
Dernière modification par Bougron (Le 28/02/2017, à 15:49)
Hors ligne
#38 Le 07/03/2017, à 11:12
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Hello,
Encore navré du délai de réponse (l'ordi qui a un problème n'est pas le mien, du coup je n'y ai pas toujours accès )
Résultat déjà du premier test (je lance le second après) :
sudo smartctl -t short /dev/sda
[sudo] Mot de passe de :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 1 minutes for test to complete.
Test will complete after Tue Mar 7 10:10:15 2017
Use smartctl -X to abort test.
$ sudo smartctl -l selftest /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 5400 -
# 2 Extended offline Interrupted (host reset) 90% 5400 -
# 3 Short offline Completed without error 00% 5400 -
# 4 Short offline Completed without error 00% 5329 -
# 5 Short captive Interrupted (host reset) 80% 5295 -
# 6 Short offline Completed without error 00% 3147 -
Hors ligne
#39 Le 07/03/2017, à 11:41
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Bonjour
Lorsque le test long sera fini, pourras-tu refaire les commandes
sudo smartctl -s on -a /dev/sda
sudo dd if=/dev/sda count=1 skip=1000
sudo dd if=/dev/sda count=1 skip=10000
sudo dd if=/dev/sda count=1 skip=100000
pour faire un point avant que j'appelle un spécialiste à l'aide
Hors ligne
#40 Le 07/03/2017, à 12:04
- Rufus T. Firefly
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Salut,
Je ne suis pas un spécialiste, loin de là, mais je ne comprends pas ces conseils !
Première des choses à essayer : gparted.
Non pas pour créer une partition, mais déjà pour créer une table de partitions ms-dos (périphérique -> nouvelle table de partitions).
Si ça ne fonctionne pas, essayer d'effacer le début du disque, mais pas avec une commande erronée, qui n'écrit qu'un seul octet :
Je te propose d'ecrire des zeros dans le premier bloc du disque.
sudo dd if=/dev/zero of=/dev/sdb count=1
Comme tu as changé des branchements, il importe de voir comment le disque est reconnu (sdX) et ne surtout pas se tromper. Je pense que gparted te permet de voir ça.
Puis :
sudo dd if=/dev/zero of=/dev/sdX count=512
Ça, ça efface le premier secteur (= 512 octets), ce qui est suffisant pour faire apparaître le disque comme sorti d'usine (sauf que, bien sûr, s'il a réellement un problème matériel, ça ne va pas le corriger).
Et enfin ré-essayer gparted -> périphérique -> nouvelle table de partitions (ms-dos, s'il demande)
Dernière modification par Rufus T. Firefly (Le 07/03/2017, à 12:18)
La provocation est une façon de remettre la réalité sur ses pieds. (Bertolt Brecht)
Il n'y a pas de route royale pour la science et ceux-là seulement ont chance d'arriver à ses sommets lumineux qui ne craignent pas de se fatiguer à gravir ses sentiers escarpés. (Karl Marx)
Il est devenu plus facile de penser la fin du monde que la fin du capitalisme
Hors ligne
#41 Le 07/03/2017, à 12:52
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Alors en premier voici le résultat des commandes de Bougron :
sudo smartctl -l selftest /dev/sda
[sudo] Mot de passe de :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 60% 5401 502087670
# 2 Short offline Completed without error 00% 5400 -
# 3 Extended offline Interrupted (host reset) 90% 5400 -
# 4 Short offline Completed without error 00% 5400 -
# 5 Short offline Completed without error 00% 5329 -
# 6 Short captive Interrupted (host reset) 80% 5295 -
# 7 Short offline Completed without error 00% 3147 -
$ sudo smartctl -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3500418AS
Serial Number: 9VMXJJF9
LU WWN Device Id: 5 000c50 02d9fb546
Firmware Version: CC49
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 7 11:49:08 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 118) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 193796753
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2199
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - 31089390
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5402
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1096
183 Runtime_Bad_Block 0x0032 093 093 000 Old_age Always - 7
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 042 000 Old_age Always - 2332202894297
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 053 045 Old_age Always - 29 (Min/Max 21/33)
194 Temperature_Celsius 0x0022 029 047 000 Old_age Always - 29 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 034 027 000 Old_age Always - 193796753
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 032 000 Old_age Always - 10942
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8292 (22 73 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 638528687
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 694704251
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 5295 hours (220 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 00 00 00 00 00 ff 00:23:08.745 NOP [Abort queued commands]
b0 d4 00 81 4f c2 e0 00 00:22:54.830 SMART EXECUTE OFF-LINE IMMEDIATE
00 00 00 00 00 00 00 04 00:22:54.811 NOP [Abort queued commands]
b0 d0 04 00 4f c2 e0 00 00:22:54.748 SMART READ DATA
00 00 00 00 00 00 00 04 00:22:51.997 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 60% 5401 502087670
# 2 Short offline Completed without error 00% 5400 -
# 3 Extended offline Interrupted (host reset) 90% 5400 -
# 4 Short offline Completed without error 00% 5400 -
# 5 Short offline Completed without error 00% 5329 -
# 6 Short captive Interrupted (host reset) 80% 5295 -
# 7 Short offline Completed without error 00% 3147 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ sudo smartctl -s on -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12
Device Model: ST3500418AS
Serial Number: 9VMXJJF9
LU WWN Device Id: 5 000c50 02d9fb546
Firmware Version: CC49
User Capacity: 500 107 862 016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Mar 7 11:49:21 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 118) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 193796753
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2199
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - 31089391
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5402
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1096
183 Runtime_Bad_Block 0x0032 093 093 000 Old_age Always - 7
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 042 000 Old_age Always - 2332202894297
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 053 045 Old_age Always - 29 (Min/Max 21/33)
194 Temperature_Celsius 0x0022 029 047 000 Old_age Always - 29 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 034 027 000 Old_age Always - 193796753
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 032 000 Old_age Always - 10942
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 8292 (73 47 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 638528687
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 694704251
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 5295 hours (220 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 00 00 00 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
00 00 00 00 00 00 00 ff 00:23:08.745 NOP [Abort queued commands]
b0 d4 00 81 4f c2 e0 00 00:22:54.830 SMART EXECUTE OFF-LINE IMMEDIATE
00 00 00 00 00 00 00 04 00:22:54.811 NOP [Abort queued commands]
b0 d0 04 00 4f c2 e0 00 00:22:54.748 SMART READ DATA
00 00 00 00 00 00 00 04 00:22:51.997 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 60% 5401 502087670
# 2 Short offline Completed without error 00% 5400 -
# 3 Extended offline Interrupted (host reset) 90% 5400 -
# 4 Short offline Completed without error 00% 5400 -
# 5 Short offline Completed without error 00% 5329 -
# 6 Short captive Interrupted (host reset) 80% 5295 -
# 7 Short offline Completed without error 00% 3147 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ sudo dd if=/dev/sda count=1 skip=1000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,149612 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 skip=10000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,144423 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 skip=100000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,149784 s, 0,0 kB/s
Dernière modification par Pascal32 (Le 07/03/2017, à 12:54)
Hors ligne
#42 Le 07/03/2017, à 18:15
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Salut,
Je ne suis pas un spécialiste, loin de là,
Si ça ne fonctionne pas, essayer d'effacer le début du disque, mais pas avec une commande erronée, qui n'écrit qu'un seul octet :
u16041@u16041:/media/u16041/FATU16041$ sudo dd if=/dev/zero of=titi count=1
1+0 enregistrements lus
1+0 enregistrements écrits
512 bytes copied, 0,00317166 s, 161 kB/s
u16041@u16041:/media/u16041/FATU16041$
Il est aussi possible de lire le message 11 de cette discussion dans sa totalité.
Dernière modification par Bougron (Le 08/03/2017, à 11:47)
Hors ligne
#43 Le 07/03/2017, à 18:22
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Merci de refaire
sudo dd if=/dev/sda count=1 bs=512
sudo dd if=/dev/sda count=1 bs=512 skip=1000
sudo dd if=/dev/sda count=1 bs=512 skip=10000
sudo dd if=/dev/sda count=1 bs=512 skip=100000
La commande pour réparer le lba (502087670) de la première erreur
On lit pour vérifier qu'on ne peut pas, on répare et on lit pour vérifier que c'est réparé
sudo dd if=/dev/sda count=1 bs=512 skip=502087670
sudo hdparm --yes-i-know-what-i-am-doing --write-sector 502087670 /dev/sda
sudo dd if=/dev/sda count=1 bs=512 skip=502087670
Si la lecture est possible, tu relances le test long.
Dernière modification par Bougron (Le 07/03/2017, à 18:27)
Hors ligne
#44 Le 08/03/2017, à 15:39
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Si je comprends bien les résultats, la lecture n'est toujours pas possible
sudo dd if=/dev/sda count=1 bs=512
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,14679 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 bs=512 skip=1000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,149373 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 bs=512 skip=1000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,156986 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 bs=512 skip=10000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,149614 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 bs=512 skip=100000
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,150381 s, 0,0 kB/s
$ sudo dd if=/dev/sda count=1 bs=512 skip=502087670
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,1463 s, 0,0 kB/s
$ sudo hdparm --yes-i-know-what-i-am-doing --write-sector 502087670 /dev/sda
/dev/sda:
re-writing sector 502087670: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 04 51 e0 01 21 04 00 00 a0 f6 00 00 00 00 00 00 00 00 00 00 00 00 00 00
succeeded
$ sudo dd if=/dev/sda count=1 bs=512 skip=502087670
dd: erreur de lecture '/dev/sda': Erreur d'entrée/sortie
0+0 enregistrements lus
0+0 enregistrements écrits
0 bytes copied, 0,157576 s, 0,0 kB/s
Hors ligne
#45 Le 08/03/2017, à 16:21
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Comme tu le dis la lecture n'est toujours pas possible, mais il semble que hdparm sache écrire...
Une commande de display
sudo hdparm -C -i -g -I /dev/sda
Je mémorise cela ( https://sourceforge.net/p/hdparm/bugs/66/ )
lktool /dev/sdc wcache off
[bugs:#66] http://sourceforge.net/p/hdparm/bugs/66/ cannot read / set
parameters on sas drives*
Status: closed-invalid
Group: v1.0 (example)
Created: Thu Jan 14, 2016 12:11 PM UTC by Marco Cusano
Last Updated: Thu Jan 14, 2016 01:05 PM UTC
Owner: Mark Lord
hdparm -i /dev/sdc
/dev/sdc:
SG_IO: bad/missing sense data, sb[]: 72 05 20 00 00 00 00 1c 02 06 00 00
cf 00 00 00 03 02 00 01 80 0e 00 00 00 00 00 00 00 00 00 00
SG_IO: bad/missing sense data, sb[]: 72 05 20 00 00 00 00 1c 02 06 00 00
cf 00 00 00 03 02 00 01 80 0e 00 00 00 00 00 00 00 00 00 00
HDIO_DRIVE_CMD(identify) failed: Input/output error
HDIO_GET_IDENTITY failed: Invalid argument
Dernière modification par Bougron (Le 08/03/2017, à 16:41)
Hors ligne
#46 Le 08/03/2017, à 17:15
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Voici la réponse de la première commande (je n'ai pas compris si je devais taper des commandes par rapport au deuxième bloc de code que tu as mis ou si tu te le mettais de côté pour plus tard ?) :
sudo hdparm -C -i -g -I /dev/sda
/dev/sda:
geometry = 60801/255/63, sectors = 976773168, start = 0
drive state is: active/idle
Model=ST3500418AS, FwRev=CC49, SerialNo=9VMXJJF9
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: unknown: ATA/ATAPI-4,5,6,7
* signifies the current active mode
ATA device, with non-removable media
Model Number: ST3500418AS
Serial Number: 9VMXJJF9
Firmware Revision: CC49
Transport: Serial
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 976773168
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 476940 MBytes
device size with M = 1000*1000: 500107 MBytes (500 GB)
cache/buffer size = 16384 KBytes
Nominal Media Rotation Rate: 7200
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = ?
Recommended acoustic management value: 208, current value: 208
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
* Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
* Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
Write-Read-Verify feature set
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Read/Write Long (AC1), obsolete
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
Security:
Master password revision code = 65534
supported
enabled
locked
not frozen
not expired: security count
supported: enhanced erase
Security level high
78min for SECURITY ERASE UNIT. 78min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000c5002d9fb546
NAA : 5
IEEE OUI : 000c50
Unique ID : 02d9fb546
Checksum: correct
Je ne comprends quasiment rien à toutes les commandes que tu me fais faire
Dernière modification par Pascal32 (Le 08/03/2017, à 17:16)
Hors ligne
#47 Le 08/03/2017, à 17:37
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Rassures-toi
Moi non plus je ne les connais que par ouî-dire.
C'est bien la première fois que je vois un cas de figure dont le smartctl semble dire que le disque est bon et qu'on est incapable de lire un seul secteur.
Je suis donc parti à la chasse à une option du firmware du disque mal positionnée.
J'ai donc mis toutes les options de lecture possibles.
De là, à trouver ce qu'il faut permuter comme option.....
Pour les autres options de premier niveau, frappes " hdparm --help"
Dernière modification par Bougron (Le 08/03/2017, à 17:37)
Hors ligne
#48 Le 08/03/2017, à 17:55
- Bougron
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Peux-tu refaire la même commande sur l'autre disque qui fonctionne
et tu compares cette expression qui m'inquiète et que j'assimile à un protocole de communication assez ancien pour savoir si c'est pareil
ATA device, with non-removable media
Model Number: ST3500418AS
Serial Number: 9VMXJJF9
Firmware Revision: CC49
Transport: Serial
Je ne suis même pas certain que le bios sache émuler
et tu regarderas aussi cette notion car il me semble bien que le problème est à cet endroit
Security:
Master password revision code = 65534
supported
enabled
locked
Donc, en premier, regardes dans ton bios si tu fonctionnes en mode sécurisé et si oui, vérifies que tu n'as pas positionné un mot de passe pour l'accès à tes disques.
( Notes que je pense que c'est plutôt le vendeur de ton disque qui a cette option de positionnée!!!!!)
Si ce n'est pas le cas
Fais la commande http://www.tomsguide.com/forum/id-18445 … nlock.html
hdparm --user-master u - - security-unlock NULL /dev/sda
qui peut être refusée car il faudra certainement que tu fournisses le_mot_de_passe_de_sécurité_qui_a_été_mis_par_le_vendeur pour empêcher_ l'acces_au_disque.
http://serverfault.com/questions/712849 … ith-hdparm
Mon sentiment est que le vendeur de ton disque a détruit le contenu du disque via hdparm avant de le mettre en vente en oubliant de supprimer le mot de passe qu'il avait mis
https://books.google.fr/books?id=zY0zDQ … 22&f=false
Dernière modification par Bougron (Le 08/03/2017, à 18:34)
Hors ligne
#49 Le 09/03/2017, à 10:32
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Alors pour la commande sur l'autre disque :
/dev/sdb1:
geometry = 60801/255/63, sectors = 964337664, start = 2048
drive state is: active/idle
Model=ST500DM002-1BD142, FwRev=KC47, SerialNo=Z3TTQNM3
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: unknown: ATA/ATAPI-4,5,6,7
* signifies the current active mode
ATA device, with non-removable media
Model Number: ST500DM002-1BD142
Serial Number: Z3TTQNM3
Firmware Revision: KC47
Transport: Serial, SATA Rev 3.0
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 976773168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 476940 MBytes
device size with M = 1000*1000: 500107 MBytes (500 GB)
cache/buffer size = 16384 KBytes
Nominal Media Rotation Rate: 7200
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = ?
Recommended acoustic management value: 208, current value: 208
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
* Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
Write-Read-Verify feature set
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Read/Write Long (AC1), obsolete
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
unknown 206[13] (vendor specific)
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
78min for SECURITY ERASE UNIT. 78min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000c50065517d16
NAA : 5
IEEE OUI : 000c50
Unique ID : 065517d16
Checksum: correct
Effectivement c'est un peu différent, on a un "Transport: Serial, SATA Rev 3.0" et
"Security:
Master password revision code = 65534
supported
not enabled
not locked"
Je vais voir dans le bios.
Hors ligne
#50 Le 09/03/2017, à 11:00
- Pascal32
Re : Problème synchronisation, entrée/sortie sur DD anciennement NTFS
Alors j'ai regardé dans le bios (je savais pas trop où regarder mais je pense avoir fouillé partout où c'était possible) et je n'ai rien vu qui signifierait qu'une quelconque option de sécurité serait activée. Par contre, dans l'onglet "avancé", il y avait le message suivant mais je ne sais pas si c'est un message de prévention ou une alerte suite à une manipulation quelconque :
Mise en garde
Un 0 (completed without error) provoquer
un mauvais fonctionnement du système
La faute d'accord est d'origine. Du coup je sais pas si ça veut dire qu'il y a un bidule qui provoque actuellement une erreur ou si c'est juste un truc qui serait possible sous condition.
Du coup j'ai tapé la commande que tu m'indiquais et ça me donne ça :
$ sudo hdparm --user-master u --security-unlock NULL /dev/sda
security_password: "NULL"
/dev/sda:
Issuing SECURITY_UNLOCK command, password="NULL", user=user
SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 04 51 40 00 21 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Et merci au fait de prendre tout ce temps à me répondre
Dernière modification par Pascal32 (Le 09/03/2017, à 11:01)
Hors ligne