#1 Le 08/03/2017, à 15:38
- bird12358
Aide pour l'installation Nvidia 940M
Bonjour,
Je galere à installer ma carte graphique pour pouvoir utiliser Cuda. Déjà ma carte graphiqe ne semble pas étre utiliser pour l'afficharge:
sudo lshw -C video
*-display
description: VGA compatible controller
produit: Broadwell-U Integrated Graphics
fabriquant: Intel Corporation
identifiant matériel: 2
information bus: pci@0000:00:02.0
version: 09
bits: 64 bits
horloge: 33MHz
fonctionnalités: msi pm vga_controller bus_master cap_list rom
configuration: driver=i915 latency=0
ressources: irq:47 mémoire:e2000000-e2ffffff mémoire:c0000000-cfffffff portE/S:4000(taille=64)
*-display NON-RÉCLAMÉ
description: 3D controller
produit: GM108M [GeForce 940M]
fabriquant: NVIDIA Corporation
identifiant matériel: 0
information bus: pci@0000:03:00.0
version: a2
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm msi pciexpress bus_master cap_list
configuration: latency=0
ressources: mémoire:e3000000-e3ffffff mémoire:d0000000-dfffffff mémoire:e0000000-e1ffffff portE/S:3000(taille=128)Voici ce que j'obtiens pour la commande lspci -v:
00:00.0 Host bridge: Intel Corporation Broadwell-U Host Bridge -OPI (rev 09)
Subsystem: Lenovo Broadwell-U Host Bridge -OPI
Flags: bus master, fast devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: bdw_uncore
00:02.0 VGA compatible controller: Intel Corporation Broadwell-U Integrated Graphics (rev 09) (prog-if 00 [VGA controller])
Subsystem: Lenovo Broadwell-U Integrated Graphics
Flags: bus master, fast devsel, latency 0, IRQ 47
Memory at e2000000 (64-bit, non-prefetchable) [size=16M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
I/O ports at 4000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:03.0 Audio device: Intel Corporation Broadwell-U Audio Controller (rev 09)
Subsystem: Lenovo Broadwell-U Audio Controller
Flags: bus master, fast devsel, latency 0, IRQ 51
Memory at e4118000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:04.0 Signal processing controller: Intel Corporation Broadwell-U Camarillo Device (rev 09)
Subsystem: Lenovo Broadwell-U Processor Thermal Subsystem
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at e4110000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: proc_thermal
Kernel modules: processor_thermal_device
00:14.0 USB controller: Intel Corporation Wildcat Point-LP USB xHCI Controller (rev 03) (prog-if 30 [XHCI])
Subsystem: Lenovo Wildcat Point-LP USB xHCI Controller
Flags: bus master, medium devsel, latency 0, IRQ 45
Memory at e4100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller: Intel Corporation Wildcat Point-LP MEI Controller #1 (rev 03)
Subsystem: Lenovo Wildcat Point-LP MEI Controller
Flags: bus master, fast devsel, latency 0, IRQ 48
Memory at e4122000 (64-bit, non-prefetchable) [size=32]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:1b.0 Audio device: Intel Corporation Wildcat Point-LP High Definition Audio Controller (rev 03)
Subsystem: Lenovo Wildcat Point-LP High Definition Audio Controller
Flags: bus master, fast devsel, latency 32, IRQ 49
Memory at e411c000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #1 (rev e3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 42
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: b0100000-b02fffff
Prefetchable memory behind bridge: 00000000b0300000-00000000b04fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #3 (rev e3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 43
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: e4000000-e40fffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #5 (rev e3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 44
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e3000000-e3ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000e1ffffff
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1f.0 ISA bridge: Intel Corporation Wildcat Point-LP LPC Controller (rev 03)
Subsystem: Lenovo Wildcat Point-LP LPC Controller
Flags: bus master, medium devsel, latency 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller: Intel Corporation Wildcat Point-LP SATA Controller [AHCI Mode] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Wildcat Point-LP SATA Controller [AHCI Mode]
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 46
I/O ports at 4088 [size=8]
I/O ports at 4094 [size=4]
I/O ports at 4080 [size=8]
I/O ports at 4090 [size=4]
I/O ports at 4060 [size=32]
Memory at e4120000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation Wildcat Point-LP SMBus Controller (rev 03)
Subsystem: Lenovo Wildcat Point-LP SMBus Controller
Flags: medium devsel, IRQ 255
Memory at e4121000 (64-bit, non-prefetchable) [size=256]
I/O ports at efa0 [size=32]
Kernel modules: i2c_i801
02:00.0 Network controller: Intel Corporation Wireless 3160 (rev 93)
Subsystem: Intel Corporation Dual Band Wireless AC 3160
Flags: bus master, fast devsel, latency 0, IRQ 50
Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
03:00.0 3D controller: NVIDIA Corporation GM108M [GeForce 940M] (rev a2)
Subsystem: Lenovo GM108M [GeForce 940M]
Flags: bus master, fast devsel, latency 0, IRQ 255
Memory at e3000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at e0000000 (64-bit, prefetchable) [size=32M]
I/O ports at 3000 [disabled] [size=128]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel modules: nvidiafb, nouveau, nvidia_367, nvidia_367_drmet la commande cat /var/log/Xorg.0.log:
[ 16.830]
X.Org X Server 1.18.4
Release Date: 2016-07-19
[ 16.830] X Protocol Version 11, Revision 0
[ 16.830] Build Operating System: Linux 4.4.0-45-generic x86_64 Ubuntu
[ 16.830] Current Operating System: Linux jeremie-Lenovo 4.4.0-64-generic #85-Ubuntu SMP Mon Feb 20 11:50:30 UTC 2017 x86_64
[ 16.830] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-64-generic.efi.signed root=UUID=18807d69-0ce2-4c3f-bc13-9762f2fa8cf2 ro quiet splash vt.handoff=7
[ 16.830] Build Date: 02 November 2016 10:06:10PM
[ 16.830] xorg-server 2:1.18.4-0ubuntu0.2 (For technical support please see http://www.ubuntu.com/support)
[ 16.830] Current version of pixman: 0.33.6
[ 16.830] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 16.830] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 16.830] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Mar 8 14:04:48 2017
[ 16.836] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 20.521] (==) No Layout section. Using the first Screen section.
[ 20.521] (==) No screen section available. Using defaults.
[ 20.521] (**) |-->Screen "Default Screen Section" (0)
[ 20.521] (**) | |-->Monitor "<default monitor>"
[ 20.521] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 20.521] (==) Automatically adding devices
[ 20.521] (==) Automatically enabling devices
[ 20.521] (==) Automatically adding GPU devices
[ 20.521] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 20.521] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 20.521] Entry deleted from font path.
[ 20.521] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[ 20.521] Entry deleted from font path.
[ 20.521] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[ 20.522] Entry deleted from font path.
[ 20.522] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[ 20.522] Entry deleted from font path.
[ 20.522] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[ 20.522] Entry deleted from font path.
[ 20.522] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/Type1,
built-ins
[ 20.522] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[ 20.522] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 20.522] (II) Loader magic: 0x563bc09f7dc0
[ 20.522] (II) Module ABI versions:
[ 20.522] X.Org ANSI C Emulation: 0.4
[ 20.522] X.Org Video Driver: 20.0
[ 20.522] X.Org XInput driver : 22.1
[ 20.522] X.Org Server Extension : 9.0
[ 20.522] (++) using VT number 7
[ 20.522] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 20.523] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 20.524] (--) PCI:*(0:0:2:0) 8086:1616:17aa:3917 rev 9, Mem @ 0xe2000000/16777216, 0xc0000000/268435456, I/O @ 0x00004000/64
[ 20.524] (--) PCI: (0:3:0:0) 10de:1347:17aa:3917 rev 162, Mem @ 0xe3000000/16777216, 0xd0000000/268435456, 0xe0000000/33554432, I/O @ 0x00003000/128
[ 20.524] (WW) "glamoregl" will not be loaded unless you've specified it to be loaded elsewhere.
[ 20.524] (II) "glx" will be loaded by default.
[ 20.524] (II) LoadModule: "glx"
[ 20.560] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 20.664] (II) Module glx: vendor="X.Org Foundation"
[ 20.664] compiled for 1.18.4, module version = 1.0.0
[ 20.664] ABI class: X.Org Server Extension, version 9.0
[ 20.664] (==) AIGLX enabled
[ 20.664] (==) Matched intel as autoconfigured driver 0
[ 20.664] (==) Matched intel as autoconfigured driver 1
[ 20.664] (==) Matched modesetting as autoconfigured driver 2
[ 20.664] (==) Matched fbdev as autoconfigured driver 3
[ 20.664] (==) Matched vesa as autoconfigured driver 4
[ 20.664] (==) Assigned the driver to the xf86ConfigLayout
[ 20.664] (II) LoadModule: "intel"
[ 20.664] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 20.668] (II) Module intel: vendor="X.Org Foundation"
[ 20.668] compiled for 1.18.4, module version = 2.99.917
[ 20.668] Module class: X.Org Video Driver
[ 20.668] ABI class: X.Org Video Driver, version 20.0
[ 20.668] (II) LoadModule: "modesetting"
[ 20.668] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 20.668] (II) Module modesetting: vendor="X.Org Foundation"
[ 20.668] compiled for 1.18.4, module version = 1.18.4
[ 20.668] Module class: X.Org Video Driver
[ 20.668] ABI class: X.Org Video Driver, version 20.0
[ 20.668] (II) LoadModule: "fbdev"
[ 20.669] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[ 20.674] (II) Module fbdev: vendor="X.Org Foundation"
[ 20.674] compiled for 1.18.1, module version = 0.4.4
[ 20.674] Module class: X.Org Video Driver
[ 20.674] ABI class: X.Org Video Driver, version 20.0
[ 20.674] (II) LoadModule: "vesa"
[ 20.674] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[ 20.685] (II) Module vesa: vendor="X.Org Foundation"
[ 20.685] compiled for 1.18.1, module version = 2.3.4
[ 20.685] Module class: X.Org Video Driver
[ 20.685] ABI class: X.Org Video Driver, version 20.0
[ 20.685] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 20.685] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000
[ 20.685] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100
[ 20.685] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300
[ 20.685] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 20.685] (II) FBDEV: driver for framebuffer: fbdev
[ 20.685] (II) VESA: driver for VESA chipsets: vesa
[ 20.685] xf86EnableIOPorts: failed to set IOPL for I/O (Operation not permitted)
[ 20.686] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20151010
[ 20.686] (II) intel(0): SNA compiled: xserver-xorg-video-intel 2:2.99.917+git20160325-1ubuntu1.2 (Timo Aaltonen <tjaalton@debian.org>)
[ 20.686] (II) intel(0): SNA compiled for use with valgrind
[ 20.687] (WW) Falling back to old probe method for modesetting
[ 20.687] (WW) Falling back to old probe method for fbdev
[ 20.687] (II) Loading sub module "fbdevhw"
[ 20.687] (II) LoadModule: "fbdevhw"
[ 20.687] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[ 20.687] (II) Module fbdevhw: vendor="X.Org Foundation"
[ 20.687] compiled for 1.18.4, module version = 0.0.2
[ 20.687] ABI class: X.Org Video Driver, version 20.0
[ 20.687] (WW) Falling back to old probe method for vesa
[ 20.688] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics 5500
[ 20.688] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2; using a maximum of 2 threads
[ 20.688] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 20.688] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 20.688] (==) intel(0): RGB weight 888
[ 20.688] (==) intel(0): Default visual is TrueColor
[ 20.688] (II) intel(0): Output eDP1 has no monitor section
[ 20.700] (--) intel(0): Found backlight control interface intel_backlight (type 'raw') for output eDP1
[ 20.700] (II) intel(0): Enabled output eDP1
[ 20.700] (II) intel(0): Output HDMI1 has no monitor section
[ 20.700] (II) intel(0): Enabled output HDMI1
[ 20.700] (--) intel(0): Using a maximum size of 256x256 for hardware cursors
[ 20.700] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 20.700] (II) intel(0): Enabled output VIRTUAL1
[ 20.700] (--) intel(0): Output eDP1 using initial mode 1920x1080 on pipe 0
[ 20.700] (==) intel(0): TearFree disabled
[ 20.700] (==) intel(0): DPI set to (96, 96)
[ 20.700] (II) Loading sub module "dri2"
[ 20.700] (II) LoadModule: "dri2"
[ 20.700] (II) Module "dri2" already built-in
[ 20.700] (II) Loading sub module "present"
[ 20.700] (II) LoadModule: "present"
[ 20.700] (II) Module "present" already built-in
[ 20.701] (II) UnloadModule: "modesetting"
[ 20.701] (II) Unloading modesetting
[ 20.701] (II) UnloadModule: "fbdev"
[ 20.701] (II) Unloading fbdev
[ 20.701] (II) UnloadSubModule: "fbdevhw"
[ 20.701] (II) Unloading fbdevhw
[ 20.701] (II) UnloadModule: "vesa"
[ 20.701] (II) Unloading vesa
[ 20.701] (==) Depth 24 pixmap format is 32 bpp
[ 20.705] (II) intel(0): SNA initialized with Broadwell (gen8) backend
[ 20.705] (==) intel(0): Backing store enabled
[ 20.705] (==) intel(0): Silken mouse enabled
[ 20.705] (II) intel(0): HW Cursor enabled
[ 20.705] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 20.706] (==) intel(0): DPMS enabled
[ 20.706] (==) intel(0): Display hotplug detection enabled
[ 20.706] (II) intel(0): [DRI2] Setup complete
[ 20.706] (II) intel(0): [DRI2] DRI driver: i965
[ 20.706] (II) intel(0): [DRI2] VDPAU driver: va_gl
[ 20.706] (II) intel(0): direct rendering: DRI2 enabled
[ 20.706] (II) intel(0): hardware support for Present enabled
[ 20.706] (--) RandR disabled
[ 20.710] (II) SELinux: Disabled on system
[ 20.728] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 20.728] (II) AIGLX: enabled GLX_ARB_create_context
[ 20.728] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 20.728] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[ 20.728] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 20.728] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 20.728] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 20.728] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 20.728] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[ 20.728] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 20.728] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[ 20.728] (II) AIGLX: Loaded and initialized i965
[ 20.728] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 20.731] (II) intel(0): switch to mode 1920x1080@60.0 on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 20.731] (II) intel(0): Setting screen physical size to 508 x 285
[ 20.808] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 20.808] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 20.808] (II) LoadModule: "evdev"
[ 20.817] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 20.854] (II) Module evdev: vendor="X.Org Foundation"
[ 20.854] compiled for 1.18.1, module version = 2.10.1
[ 20.854] Module class: X.Org XInput Driver
[ 20.854] ABI class: X.Org XInput driver, version 22.1
[ 20.854] (II) Using input driver 'evdev' for 'Power Button'
[ 20.854] (**) Power Button: always reports core events
[ 20.854] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 20.854] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 20.854] (--) evdev: Power Button: Found keys
[ 20.854] (II) evdev: Power Button: Configuring as keyboard
[ 20.854] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 20.854] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 20.854] (**) Option "xkb_rules" "evdev"
[ 20.854] (**) Option "xkb_model" "pc105"
[ 20.854] (**) Option "xkb_layout" "fr"
[ 20.854] (**) Option "xkb_variant" "latin9"
[ 20.867] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
[ 20.867] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 20.867] (II) Using input driver 'evdev' for 'Video Bus'
[ 20.867] (**) Video Bus: always reports core events
[ 20.867] (**) evdev: Video Bus: Device: "/dev/input/event4"
[ 20.867] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 20.867] (--) evdev: Video Bus: Found keys
[ 20.867] (II) evdev: Video Bus: Configuring as keyboard
[ 20.867] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6/event4"
[ 20.867] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 20.867] (**) Option "xkb_rules" "evdev"
[ 20.867] (**) Option "xkb_model" "pc105"
[ 20.867] (**) Option "xkb_layout" "fr"
[ 20.867] (**) Option "xkb_variant" "latin9"
[ 20.867] (II) config/udev: Adding input device Video Bus (/dev/input/event5)
[ 20.868] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 20.868] (II) Using input driver 'evdev' for 'Video Bus'
[ 20.868] (**) Video Bus: always reports core events
[ 20.868] (**) evdev: Video Bus: Device: "/dev/input/event5"
[ 20.868] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 20.868] (--) evdev: Video Bus: Found keys
[ 20.868] (II) evdev: Video Bus: Configuring as keyboard
[ 20.868] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:4f/LNXVIDEO:01/input/input7/event5"
[ 20.868] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 20.868] (**) Option "xkb_rules" "evdev"
[ 20.868] (**) Option "xkb_model" "pc105"
[ 20.868] (**) Option "xkb_layout" "fr"
[ 20.868] (**) Option "xkb_variant" "latin9"
[ 20.868] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 20.868] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 20.868] (II) Using input driver 'evdev' for 'Power Button'
[ 20.868] (**) Power Button: always reports core events
[ 20.868] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 20.868] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 20.868] (--) evdev: Power Button: Found keys
[ 20.868] (II) evdev: Power Button: Configuring as keyboard
[ 20.868] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1/event1"
[ 20.868] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 9)
[ 20.868] (**) Option "xkb_rules" "evdev"
[ 20.868] (**) Option "xkb_model" "pc105"
[ 20.868] (**) Option "xkb_layout" "fr"
[ 20.868] (**) Option "xkb_variant" "latin9"
[ 20.868] (II) config/udev: Adding input device Lid Switch (/dev/input/event0)
[ 20.868] (II) No input driver specified, ignoring this device.
[ 20.868] (II) This device may have been added with another device file.
[ 20.869] (II) config/udev: Adding input device HDA Intel HDMI HDMI/DP,pcm=3 (/dev/input/event10)
[ 20.869] (II) No input driver specified, ignoring this device.
[ 20.869] (II) This device may have been added with another device file.
[ 20.869] (II) config/udev: Adding input device HDA Intel HDMI HDMI/DP,pcm=7 (/dev/input/event11)
[ 20.869] (II) No input driver specified, ignoring this device.
[ 20.869] (II) This device may have been added with another device file.
[ 20.869] (II) config/udev: Adding input device HDA Intel HDMI HDMI/DP,pcm=8 (/dev/input/event12)
[ 20.869] (II) No input driver specified, ignoring this device.
[ 20.869] (II) This device may have been added with another device file.
[ 20.869] (II) config/udev: Adding input device Lenovo EasyCamera (/dev/input/event13)
[ 20.869] (**) Lenovo EasyCamera: Applying InputClass "evdev keyboard catchall"
[ 20.869] (II) Using input driver 'evdev' for 'Lenovo EasyCamera'
[ 20.869] (**) Lenovo EasyCamera: always reports core events
[ 20.869] (**) evdev: Lenovo EasyCamera: Device: "/dev/input/event13"
[ 20.869] (--) evdev: Lenovo EasyCamera: Vendor 0x5986 Product 0x701
[ 20.869] (--) evdev: Lenovo EasyCamera: Found keys
[ 20.869] (II) evdev: Lenovo EasyCamera: Configuring as keyboard
[ 20.869] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/input/input14/event13"
[ 20.869] (II) XINPUT: Adding extended input device "Lenovo EasyCamera" (type: KEYBOARD, id 10)
[ 20.869] (**) Option "xkb_rules" "evdev"
[ 20.869] (**) Option "xkb_model" "pc105"
[ 20.869] (**) Option "xkb_layout" "fr"
[ 20.869] (**) Option "xkb_variant" "latin9"
[ 20.870] (II) config/udev: Adding input device ELAN Touchscreen (/dev/input/event14)
[ 20.870] (**) ELAN Touchscreen: Applying InputClass "evdev touchscreen catchall"
[ 20.870] (II) Using input driver 'evdev' for 'ELAN Touchscreen'
[ 20.870] (**) ELAN Touchscreen: always reports core events
[ 20.870] (**) evdev: ELAN Touchscreen: Device: "/dev/input/event14"
[ 20.870] (--) evdev: ELAN Touchscreen: Vendor 0x4f3 Product 0x206f
[ 20.870] (--) evdev: ELAN Touchscreen: Found absolute axes
[ 20.870] (--) evdev: ELAN Touchscreen: Found absolute multitouch axes
[ 20.870] (II) evdev: ELAN Touchscreen: No buttons found, faking one.
[ 20.870] (--) evdev: ELAN Touchscreen: Found x and y absolute axes
[ 20.870] (--) evdev: ELAN Touchscreen: Found absolute touchscreen
[ 20.870] (II) evdev: ELAN Touchscreen: Configuring as touchscreen
[ 20.870] (**) evdev: ELAN Touchscreen: YAxisMapping: buttons 4 and 5
[ 20.870] (**) evdev: ELAN Touchscreen: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 20.870] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/0003:04F3:206F.0002/input/input15/event14"
[ 20.870] (II) XINPUT: Adding extended input device "ELAN Touchscreen" (type: TOUCHSCREEN, id 11)
[ 20.870] (II) evdev: ELAN Touchscreen: initialized for absolute axes.
[ 20.870] (**) ELAN Touchscreen: (accel) keeping acceleration scheme 1
[ 20.870] (**) ELAN Touchscreen: (accel) acceleration profile 0
[ 20.870] (**) ELAN Touchscreen: (accel) acceleration factor: 2.000
[ 20.870] (**) ELAN Touchscreen: (accel) acceleration threshold: 4
[ 20.870] (II) config/udev: Adding input device ELAN Touchscreen (/dev/input/mouse1)
[ 20.870] (II) No input driver specified, ignoring this device.
[ 20.870] (II) This device may have been added with another device file.
[ 20.871] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event9)
[ 20.871] (II) No input driver specified, ignoring this device.
[ 20.871] (II) This device may have been added with another device file.
[ 20.871] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event8)
[ 20.871] (II) No input driver specified, ignoring this device.
[ 20.871] (II) This device may have been added with another device file.
[ 20.871] (II) config/udev: Adding input device Ideapad extra buttons (/dev/input/event7)
[ 20.871] (**) Ideapad extra buttons: Applying InputClass "evdev keyboard catchall"
[ 20.871] (II) Using input driver 'evdev' for 'Ideapad extra buttons'
[ 20.871] (**) Ideapad extra buttons: always reports core events
[ 20.871] (**) evdev: Ideapad extra buttons: Device: "/dev/input/event7"
[ 20.871] (--) evdev: Ideapad extra buttons: Vendor 0 Product 0
[ 20.871] (--) evdev: Ideapad extra buttons: Found keys
[ 20.871] (II) evdev: Ideapad extra buttons: Configuring as keyboard
[ 20.871] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input8/event7"
[ 20.871] (II) XINPUT: Adding extended input device "Ideapad extra buttons" (type: KEYBOARD, id 12)
[ 20.871] (**) Option "xkb_rules" "evdev"
[ 20.871] (**) Option "xkb_model" "pc105"
[ 20.871] (**) Option "xkb_layout" "fr"
[ 20.871] (**) Option "xkb_variant" "latin9"
[ 20.871] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event3)
[ 20.871] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 20.871] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 20.871] (**) AT Translated Set 2 keyboard: always reports core events
[ 20.871] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event3"
[ 20.871] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 20.871] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 20.871] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 20.871] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input3/event3"
[ 20.871] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 13)
[ 20.871] (**) Option "xkb_rules" "evdev"
[ 20.871] (**) Option "xkb_model" "pc105"
[ 20.871] (**) Option "xkb_layout" "fr"
[ 20.871] (**) Option "xkb_variant" "latin9"
[ 20.872] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/event6)
[ 20.872] (**) ETPS/2 Elantech Touchpad: Applying InputClass "evdev touchpad catchall"
[ 20.872] (**) ETPS/2 Elantech Touchpad: Applying InputClass "evdev touchscreen catchall"
[ 20.872] (**) ETPS/2 Elantech Touchpad: Applying InputClass "touchpad catchall"
[ 20.872] (**) ETPS/2 Elantech Touchpad: Applying InputClass "Default clickpad buttons"
[ 20.872] (II) LoadModule: "synaptics"
[ 20.872] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 20.873] (II) Module synaptics: vendor="X.Org Foundation"
[ 20.873] compiled for 1.18.1, module version = 1.8.2
[ 20.873] Module class: X.Org XInput Driver
[ 20.873] ABI class: X.Org XInput driver, version 22.1
[ 20.873] (II) Using input driver 'synaptics' for 'ETPS/2 Elantech Touchpad'
[ 20.873] (**) ETPS/2 Elantech Touchpad: always reports core events
[ 20.873] (**) Option "Device" "/dev/input/event6"
[ 20.928] (II) synaptics: ETPS/2 Elantech Touchpad: found clickpad property
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: x-axis range 0 - 3120 (res 32)
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: y-axis range 0 - 2028 (res 33)
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: pressure range 0 - 255
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: finger width range 0 - 15
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: buttons: left double triple
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: Vendor 0x2 Product 0xe
[ 20.928] (**) Option "SoftButtonAreas" "50% 0 82% 0 0 0 0 0"
[ 20.928] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[ 20.928] (**) ETPS/2 Elantech Touchpad: always reports core events
[ 20.952] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input5/event6"
[ 20.952] (II) XINPUT: Adding extended input device "ETPS/2 Elantech Touchpad" (type: TOUCHPAD, id 14)
[ 20.952] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MinSpeed is now constant deceleration 2.5
[ 20.952] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MaxSpeed is now 1.75
[ 20.952] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) AccelFactor is now 0.054
[ 20.952] (**) ETPS/2 Elantech Touchpad: (accel) keeping acceleration scheme 1
[ 20.952] (**) ETPS/2 Elantech Touchpad: (accel) acceleration profile 1
[ 20.952] (**) ETPS/2 Elantech Touchpad: (accel) acceleration factor: 2.000
[ 20.952] (**) ETPS/2 Elantech Touchpad: (accel) acceleration threshold: 4
[ 20.952] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[ 20.952] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/mouse0)
[ 20.952] (**) ETPS/2 Elantech Touchpad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 22.701] (II) intel(0): EDID vendor "CMN", prod id 5302
[ 22.701] (II) intel(0): Printing DDC gathered Modelines:
[ 22.701] (II) intel(0): Modeline "1920x1080"x0.0 136.62 1920 1964 1992 2070 1080 1082 1086 1100 -hsync -vsync (66.0 kHz eP)Est ce que quelqu'un pourrait me donner un coup de main pour l'install. J'ai essayer d'installer bumblebee et le driver nvidia en manuel mais sans succés.
D'avance merci.
Hors ligne
#2 Le 08/03/2017, à 18:54
- GammaDraconis
Re : Aide pour l'installation Nvidia 940M
Mais c'est hyper simple sous Ubuntu a activer le pilote graphique !
Tu as un gestionnaire de pilote dans Ubuntu, il détecte automatiquement ta carte (et cette carte est bien détecté), il te suffit de cocher la case pour activer le driver.
A noté que si tu veux utiliser le principe de la technologie Optimus afin de pouvoir switcher entre la carte nvidia & intel, sache que c'est intégré dans le pilote nvidia, il faut d'abord :
- Activer le pilote dans le gestionnaire de pilote
- Redémarrer
- Par défaut tu sera avec la carte nvidia, si tu veux switcher sur intel (conseillé si tu utilises le portable sur batterie), il te suffira de lancer l'interface nvidia (tu auras un icone) et tu auras une option pour switcher.
(A noté qu'il faut relancer la session utilisateur pour que le switch soit pris en compte).
Discussion sur mon script de post-install pour Ubuntu 20.04LTS : https://forum.ubuntu-fr.org/viewtopic.php?id=2026344
Lien direct script : https://github.com/simbd/Ubuntu_20.04LTS_PostInstall
Démo vidéo (peertube) : https://video.ploud.fr/videos/watch/fb7 … 0d252ed2db
Hors ligne