[Résolu] Mounting local filesystems.... failed

Mr. Fuzzybass · Le 03/03/2006, à 20:18

J'ai deux problème en fait et je crois qu'il pourrais être relié.

1- Je ne peux plus écrire sur mon /home un message me dit qu'il ne peux être écrit parce qu'il est plein, alors qu'il a environ 9Go et j'ai pratiquement rien dessus...

2- Quand ma Kubuntu démarre j'obtiens un ''failed'' à la ligne: Mounting local filesystems
Voici mon dmesg:

Qs 3 4 5 7 9 10 *11 12 14 15)
[ 26.793842] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 26.794198] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *
0, disabled.
[ 26.794569] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 26.794933] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 26.795300] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *
0, disabled.
[ 26.795700] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 26.796091] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 26.796486] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 26.796876] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 26.797180] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 26.797586] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 26.797986] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[ 26.798393] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 26.798793] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 26.799192] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 26.799597] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 26.799997] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 26.800403] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 26.800818] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[ 26.801235] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[ 26.801655] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[ 26.804374] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 26.804381] pnp: PnP ACPI init
[ 26.809618] pnp: PnP ACPI: found 12 devices
[ 26.809684] usbcore: registered new driver usbfs
[ 26.809699] usbcore: registered new driver hub
[ 26.809729] PCI: Using ACPI for IRQ routing
[ 26.809733] PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
[ 26.809792] PCI-DMA: Disabling IOMMU.
[ 26.810131] pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
[ 26.810134] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[ 26.810137] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[ 26.810140] pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
[ 26.810143] pnp: 00:00: ioport range 0x4800-0x487f has been reserved
[ 26.810145] pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
[ 26.810372] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp
$
[ 26.810523] audit: initializing netlink socket (disabled)
[ 26.810531] audit: initialized
[ 26.810612] VFS: Disk quotas dquot_6.5.1
[ 26.810624] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 26.810647] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[ 26.810650] devfs: boot_options: 0x0
[ 26.810670] Initializing Cryptographic API
[ 26.810745] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 26.810748] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor
BIOS
[ 26.810762] assign_interrupt_mode Found MSI capability
[ 26.810764] Allocate Port Service[pcie00]
[ 26.810792] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 26.810795] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor
BIOS
[ 26.810808] assign_interrupt_mode Found MSI capability
[ 26.810810] Allocate Port Service[pcie00]
[ 26.810832] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 26.810834] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor
BIOS
[ 26.810848] assign_interrupt_mode Found MSI capability
[ 26.810850] Allocate Port Service[pcie00]
[ 26.810871] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 26.810874] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor
BIOS
[ 26.810886] assign_interrupt_mode Found MSI capability
[ 26.810888] Allocate Port Service[pcie00]
[ 26.823424] Linux agpgart interface v0.101 (c) Dave Jones
[ 26.823479] PNP: PS/2 controller doesn't have AUX irq; using default 0xc
[ 26.823483] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
[ 26.824939] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 26.825101] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 26.825104] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
[ 26.825202] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 26.826485] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 26.826543] io scheduler noop registered
[ 26.826555] io scheduler anticipatory registered
[ 26.826559] io scheduler deadline registered
[ 26.826564] io scheduler cfq registered
[ 26.826797] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 bloc
ksize
[ 26.826848] NET: Registered protocol family 2
[ 26.835261] IP: routing cache hash table of 8192 buckets, 64Kbytes
[ 26.835392] TCP established hash table entries: 262144 (order: 9, 2097152 byt
es)
[ 26.836602] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 26.836905] TCP: Hash tables configured (established 262144 bind 65536)
[ 26.836963] NET: Registered protocol family 8
[ 26.836965] NET: Registered protocol family 20
[ 26.837059] ACPI wakeup devices:
[ 26.837061] HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1
[ 26.837066] ACPI: (supports S0 S1 S4 S5)
[ 26.837211] Freeing unused kernel memory: 136k freed
[ 26.848266] vga16fb: initializing
[ 26.848269] vga16fb: mapped to 0xffff8100000a0000
[ 27.063285] Console: switching to colour frame buffer device 80x30
[ 27.063290] fb0: VGA16 VGA frame buffer device
[ 27.183749] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 28.206519] Capability LSM initialized
[ 28.213730] NET: Registered protocol family 1
[ 28.221444] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 28.221454] ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
[ 28.221457] ACPI: bus type ide registered
[ 28.224268] SCSI subsystem initialized
[ 28.225153] libata version 1.11 loaded.
[ 28.226050] sata_nv version 0.6
[ 28.226604] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 28.226611] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 23 (lev
el, low) -> IRQ 23
[ 28.226627] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 28.226665] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF600 irq 23
[ 28.226680] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF608 irq 23
[ 28.580877] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 8
7:4063 88:407f
[ 28.580881] ata1: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
[ 28.581818] nv_sata: Primary device added
[ 28.581819] nv_sata: Primary device removed
[ 28.581821] nv_sata: Secondary device added
[ 28.581823] nv_sata: Secondary device removed
[ 28.581825] ata1: dev 0 configured for UDMA/133
[ 28.581827] scsi0 : sata_nv
[ 28.782627] ata2: no device found (phy stat 00000000)
[ 28.782629] scsi1 : sata_nv
[ 28.782692] Vendor: ATA Model: Maxtor 6B160M0 Rev: BANC
[ 28.782698] Type: Direct-Access ANSI SCSI revision:
05
[ 28.783807] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 28.783812] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (lev
el, low) -> IRQ 22
[ 28.783820] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 28.783836] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF100 irq 22
[ 28.783851] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF108 irq 22
[ 28.984460] ata3: no device found (phy stat 00000000)
[ 28.984462] scsi2 : sata_nv
[ 29.185295] ata4: no device found (phy stat 00000000)
[ 29.185297] scsi3 : sata_nv
[ 29.199970] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
[ 29.199987] NFORCE-CK804: chipset revision 242
[ 29.199989] NFORCE-CK804: not 100% native mode: will probe irqs later
[ 29.199995] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
[ 29.200003] ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DM
A
[ 29.200011] ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DM
A
[ 29.200018] Probing IDE interface ide0...
[ 29.870806] hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
[ 30.177279] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 30.177325] Probing IDE interface ide1...
[ 30.695084] Probing IDE interface ide1...
[ 31.212630] Probing IDE interface ide2...
[ 31.724210] Probing IDE interface ide3...
[ 32.235790] Probing IDE interface ide4...
[ 32.747371] Probing IDE interface ide5...
[ 33.264893] hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 33.264900] Uniform CD-ROM driver Revision: 3.20
[ 33.274985] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[ 33.274994] SCSI device sda: drive cache: write back
[ 33.275050] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[ 33.275057] SCSI device sda: drive cache: write back
[ 33.275059] /dev/scsi/host0/bus0/target0/lun0: p1 < p5 p6 p7 p8 > p2
[ 33.343905] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 33.550193] Attempting manual resume
[ 33.550325] swsusp: Suspend partition has wrong signature?
[ 33.564667] ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Drive
r (PCI)
[ 33.565140] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 33.565147] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (lev
el, low) -> IRQ 21
[ 33.565163] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 33.565166] ohci_hcd 0000:00:02.0: nVidia Corporation CK804 USB Controller
[ 33.577804] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus numbe
r 1
[ 33.577813] ohci_hcd 0000:00:02.0: irq 21, io mem 0xfebff000
[ 33.630696] hub 1-0:1.0: USB hub found
[ 33.630704] hub 1-0:1.0: 10 ports detected
[ 33.638393] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[ 33.638400] ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [APCL] -> GSI 20 (lev
el, low) -> IRQ 20
[ 33.638414] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 33.638417] ehci_hcd 0000:00:02.1: nVidia Corporation CK804 USB Controller
[ 33.638423] ehci_hcd 0000:00:02.1: debug port 1
[ 33.638458] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus numbe
r 2
[ 33.638468] ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
[ 33.638491] PCI: cache line size of 64 is not supported by device 0000:00:02.
1
[ 33.638494] ehci_hcd 0000:00:02.1: park 0
[ 33.638499] ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10
Dec 2004
[ 33.638564] hub 2-0:1.0: USB hub found
[ 33.638570] hub 2-0:1.0: 10 ports detected
[ 33.682282] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0
.41.
[ 33.682758] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[ 33.682762] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (lev
el, low) -> IRQ 23
[ 33.682768] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 34.022343] ohci_hcd 0000:00:02.0: wakeup
[ 34.194339] eth0: forcedeth.c: subsystem: 01462:7125 bound to 0000:00:0a.0
[ 34.362046] usb 1-6: new full speed USB device using ohci_hcd and address 2
[ 34.651807] usb 1-8: new low speed USB device using ohci_hcd and address 3
[ 36.243503] usbcore: registered new driver hiddev
[ 36.253513] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on u
sb-0000:00:02.0-8
[ 36.253520] usbcore: registered new driver usbhid
[ 36.253522] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 36.658997] ACPI: Fan [FAN] (on)
[ 36.660915] ACPI: CPU0 (power states: C1[C1])
[ 36.661816] ACPI: Thermal Zone [THRM] (22 C)
[ 36.867966] Attempting manual resume
[ 36.868097] swsusp: Suspend partition has wrong signature?
[ 36.873553] kjournald starting. Commit interval 5 seconds
[ 36.873562] EXT3-fs: mounted filesystem with ordered data mode.
[ 37.596100] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 40.418547] Adding 2112508k swap on /dev/sda6. Priority:-1 extents:1
[ 40.662354] EXT3 FS on sda8, internal journal
[ 43.121677] parport: PnPBIOS parport detected.
[ 43.121722] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 43.204718] lp0: using parport0 (interrupt-driven).
[ 43.234076] mice: PS/2 mouse device common for all mice
[ 43.274105] Real Time Clock Driver v1.12
[ 43.290429] nvidia: module license 'NVIDIA' taints kernel.
[ 43.326705] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 43.326713] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (lev
el, low) -> IRQ 18
[ 43.326722] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 43.326832] NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module 1.0-7667
Fri Jun 17 07:14:03 PDT 2005
[ 46.326893] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@red
hat.com
[ 47.070760] cdrom: open failed.
[ 47.748723] kjournald starting. Commit interval 5 seconds
[ 47.748824] EXT3 FS on sda7, internal journal
[ 47.748828] EXT3-fs: mounted filesystem with ordered data mode.
[ 47.786143] NTFS driver 2.1.22 [Flags: R/O MODULE].
[ 47.840387] NTFS volume version 3.1.
[ 47.859052] NTFS-fs error (device sda5): read_ntfs_boot_sector(): Primary boo
t sector is invalid.
[ 47.859058] NTFS-fs error (device sda5): read_ntfs_boot_sector(): Mount optio
n errors=recover not used. Aborting without trying to recover.
[ 47.859062] NTFS-fs error (device sda5): ntfs_fill_super(): Not an NTFS volum
e.
[ 47.940609] FAT: utf8 is not a recommended IO charset for FAT filesystems, fi
lesystem will be case sensitive!
[ 49.270478] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 49.281252] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 49.836503] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[ 49.836508] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (lev
el, low) -> IRQ 22
[ 49.836532] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 50.146085] intel8x0_measure_ac97_clock: measured 49639 usecs
[ 50.146088] intel8x0: clocking to 46873
[ 50.857290] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 50.919418] shpchp: Address64 -------- Resource unparsed
[ 50.919422] shpchp: Address64 -------- Resource unparsed
[ 50.919425] shpchp: Address64 -------- Resource unparsed
[ 50.926608] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 52.735528] usbcore: registered new driver snd-usb-audio
[ 53.049973] input: PC Speaker
[ 53.111782] Floppy drive(s): fd0 is 1.44M
[ 53.139416] FDC 0 is a post-1991 82077
[ 53.618304] ts: Compaq touchscreen protocol output
[ 54.979686] NET: Registered protocol family 17
[ 56.486776] NET: Registered protocol family 10
[ 56.486863] Disabled Privacy Extensions on device ffffffff8035a7c0(lo)
[ 56.487203] IPv6 over IPv4 tunneling driver
[ 57.885352] ACPI: Power Button (FF) [PWRF]
[ 57.885362] ACPI: Power Button (CM) [PWRB]
[ 57.953688] ibm_acpi: ec object not found
[ 62.487229] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.40.4)
[ 62.487468] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2 (1500 mV)
[ 62.487472] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6 (1400 mV)
[ 62.487475] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xa (1300 mV)
[ 62.487479] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
[ 62.487834] cpu_init done, current fid 0xe, vid 0x0
[ 62.500057] powernow-k8: ph2 null fid transition 0xe
[ 67.351691] eth0: no IPv6 routers present

Et voici mon /etc/fstab:

# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/sda8 / ext3 defaults,errors=remount-ro 0 1
/dev/sda7 /home ext3 defaults 0 2
/dev/sda2 /media/sda2 ntfs defaults 0 0
/dev/sda5 /media/sda5 ntfs defaults 0 0
/dev/sda6 none swap sw 0 0
/dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
# Partitions Windows - FAT32
/dev/sda5 /home/hugo/Desktop/Multimédia vfat rw,user,auto,gid=100,uid=1000,umask=002,iocharset=utf8,codepage=850 0 0

Aurait-il moyen de régler ces problèmes ?

Merci d'avance

Dernière modification par Mr. Fuzzybass (Le 03/03/2006, à 22:33)

Link31 · Le 03/03/2006, à 20:56

Mr. Fuzzybass a écrit :

[ 47.859052] NTFS-fs error (device sda5): read_ntfs_boot_sector(): Primary boot sector is invalid.
[ 47.859058] NTFS-fs error (device sda5): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
[ 47.859062] NTFS-fs error (device sda5): ntfs_fill_super(): Not an NTFS volume.

Il y a un problème avec la partition /dev/sda5. Regarde mieux ton /etc/fstab :

/dev/sda5       /media/sda5     ntfs    defaults        0       0
...
/dev/sda5    /home/hugo/Desktop/Multimédia    vfat  rw,user,auto,gid=100,uid=1000,umask=002,iocharset=utf8,codepage=850    0    0

Tu as deux fois ta partition /dev/sda5. Alors commente la mauvaise ligne (edit : celle avec /media/sda5) et redémarre.

Dernière modification par Link31 (Le 03/03/2006, à 20:58)

Mr. Fuzzybass · Le 03/03/2006, à 22:31

J'ai enlever la ligne:

/dev/sda5 /media/sda5 ntfs defaults 0 0

Maintenant au démarrage il n'y a plus de ''failed'' donc un de mes deux problèmes est résolu, merci Link31 !

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 03/03/2006, à 20:18

[Résolu] Mounting local filesystems.... failed

#2 Le 03/03/2006, à 20:56

Re : [Résolu] Mounting local filesystems.... failed

#3 Le 03/03/2006, à 22:31

Re : [Résolu] Mounting local filesystems.... failed

Pied de page des forums