Lenteur démarrage Kernel +1min [Résolu]

Maamon · Le 11/10/2019, à 22:44

Bonsoir à tous, depuis peu Ubuntu est très long a démarrer.

Le kernel serait en cause, + de 1min quand je tape systemd-analyze time.

Avez-vous des idées ?

Dernière modification par Maamon (Le 12/10/2019, à 22:43)

geole · Le 11/10/2019, à 23:41

Bonsoir
Ainsi que

systemd-analyze

cat  /etc/fstab | grep -v "#"

sudo blkid

moko138 · Le 12/10/2019, à 00:02

geole
Attention !

cat *.txt

# fstab
UUID=... / ext4 errors=remount-ro 0 1 # racine
UUID=... /home ext4 defaults 0 2
UUID=... none swap sw,nofail 0 0

cat *.txt | grep -v "^#"

UUID=...  /            ext4    errors=remount-ro 0  1   # racine
UUID=...  /home        ext4    defaults          0  2
UUID=...  none         swap    sw,nofail         0  0

N'est PAS équivalent à :

cat *.txt | grep -v "#"
UUID=...  /home        ext4    defaults          0  2
UUID=...  none         swap    sw,nofail         0  0

Maamon · Le 12/10/2019, à 01:28

systemd-analyze blame
         10.585s packagekit.service
         10.347s apport-autoreport.service
          1.192s dev-sda2.device
           874ms dev-loop0.device
           855ms dev-loop2.device
           855ms dev-loop1.device
           830ms dev-loop4.device
           825ms dev-loop3.device
           794ms dev-loop5.device
           793ms dev-loop8.device
           769ms dev-loop9.device
           731ms dev-loop10.device
           720ms dev-loop7.device
           718ms dev-loop6.device
           715ms snapd.service
           698ms fwupd.service
           690ms systemd-logind.service
           628ms dev-loop12.device
           623ms dev-loop11.device
           607ms snap-core-7917.mount
           590ms snap-gnome\x2dcharacters-317.mount
           586ms dev-loop13.device
           579ms systemd-journal-flush.service

systemd-analyze
Startup finished in 21.415s (firmware) + 4.024s (loader) + 1min 5.306s (kernel) + 2.447s (userspace) = 1min 33.193s
graphical.target reached after 2.444s in userspace

cat  /etc/fstab | grep -v "#"
UUID=44899cbb-c047-4eed-914e-2e6e7230c525 /               ext4    errors=remount-ro 0       1
UUID=9A02-8480  /boot/efi       vfat    umask=0077      0       1
/swapfile                                 none            swap    sw

sudo blkid
[sudo] Mot de passe de maamon : 
/dev/loop0: TYPE="squashfs"
/dev/loop1: TYPE="squashfs"
/dev/loop2: TYPE="squashfs"
/dev/loop3: TYPE="squashfs"
/dev/loop4: TYPE="squashfs"
/dev/loop5: TYPE="squashfs"
/dev/loop6: TYPE="squashfs"
/dev/loop7: TYPE="squashfs"
/dev/sda1: UUID="9A02-8480" TYPE="vfat" PARTLABEL="EFI System Partition" PARTUUID="ec16f003-8e03-4e4b-9667-cc4cf284c76d"
/dev/sda2: UUID="44899cbb-c047-4eed-914e-2e6e7230c525" TYPE="ext4" PARTUUID="30252c37-e24a-4976-aee7-f89ccedf9e02"
/dev/sdb1: UUID="4df57cdc-69fd-4d99-81aa-13b7d4616ba8" TYPE="ext4" PARTUUID="2bd2c32a-01"
/dev/sdb5: UUID="01D56CD238D67B50" TYPE="ntfs" PARTUUID="2bd2c32a-05"
/dev/loop8: TYPE="squashfs"
/dev/loop9: TYPE="squashfs"
/dev/loop10: TYPE="squashfs"
/dev/loop11: TYPE="squashfs"
/dev/loop12: TYPE="squashfs"
/dev/loop13: TYPE="squashfs"
/dev/loop14: TYPE="squashfs"
/dev/loop15: TYPE="squashfs"

voila

Maamon · Le 12/10/2019, à 11:37

Ca parle à quelqu'un ?

xubu1957 · Le 12/10/2019, à 11:43

Bonjour,

Montre :

snap list --all

ylag · Le 12/10/2019, à 12:55

Bonjour,

Peut-être aussi montrer le retour de:

dmesg

...immédiatement après un démarrage ?

A+

Maamon · Le 12/10/2019, à 13:41

Le résultat de snap list --all

snap list --all
Nom                   Version                     Révision  Suivi     Éditeur     Notes
core                  16-2.41                     7713      stable    canonical✓  core,désactivé
core                  16-2.42                     7917      stable    canonical✓  core
core18                20190904                    1144      stable    canonical✓  base,désactivé
core18                20191001                    1192      stable    canonical✓  base
gnome-3-28-1804       3.28.0-10-gaa70833.aa70833  67        stable/…  canonical✓  désactivé
gnome-3-28-1804       3.28.0-10-gaa70833.aa70833  71        stable/…  canonical✓  -
gnome-calculator      3.32.1                      406       stable/…  canonical✓  désactivé
gnome-calculator      3.34.0+git1.822e4b58        501       stable/…  canonical✓  -
gnome-characters      v3.32.1+git2.3367201        296       stable/…  canonical✓  désactivé
gnome-characters      v3.32.1+git2.3367201        317       stable/…  canonical✓  -
gnome-logs            3.34.0                      81        stable/…  canonical✓  -
gnome-logs            3.34.0                      73        stable/…  canonical✓  désactivé
gnome-system-monitor  3.32.1-3-g0ea89b4922        100       stable/…  canonical✓  -
gtk-common-themes     0.1-25-gcc83164             1353      stable/…  canonical✓  -
gtk-common-themes     0.1-22-gab0a26b             1313      stable/…  canonical✓  désactivé
notepadqq             1.4.8                       855       stable    danieleds

Voila le résultat de dmesg juste après un redémarrage.

dmesg
[    0.000000] Linux version 5.0.0-31-generic (buildd@lgw01-amd64-046) (gcc version 7.4.0 (Ubuntu 7.4.0-1ubuntu1~18.04.1)) #33~18.04.1-Ubuntu SMP Tue Oct 1 10:20:39 UTC 2019 (Ubuntu 5.0.0-31.33~18.04.1-generic 5.0.21)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-5.0.0-31-generic root=UUID=44899cbb-c047-4eed-914e-2e6e7230c525 ro quiet splash vt.handoff=1
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000001d7ffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000001d80000-0x0000000001ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000002000000-0x00000000db5c8fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000db5c9000-0x00000000dcbc8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000dcbc9000-0x00000000dd019fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000dd01a000-0x00000000dd3e8fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000dd3e9000-0x00000000de2e8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000de2e9000-0x00000000de3e8fff] type 20
[    0.000000] BIOS-e820: [mem 0x00000000de3e9000-0x00000000deffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000df000000-0x00000000dfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fdf00000-0x00000000fdffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec30000-0x00000000fec30fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041f37ffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.60 by American Megatrends
[    0.000000] efi:  ACPI 2.0=0xdd01a000  ACPI=0xdd01a000  SMBIOS=0xde258000  ESRT=0xd96dc598  MEMATTR=0xd941e018 
[    0.000000] secureboot: Secure boot could not be determined (mode 0)
[    0.000000] SMBIOS 3.0 present.
[    0.000000] DMI: Micro-Star International Co., Ltd MS-7A34/B350 TOMAHAWK (MS-7A34), BIOS 1.30 04/10/2017
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 3999.956 MHz processor
[    0.000895] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000896] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000903] last_pfn = 0x41f380 max_arch_pfn = 0x400000000
[    0.000907] MTRR default type: uncachable
[    0.000907] MTRR fixed ranges enabled:
[    0.000908]   00000-9FFFF write-back
[    0.000909]   A0000-BFFFF write-through
[    0.000909]   C0000-FFFFF write-protect
[    0.000910] MTRR variable ranges enabled:
[    0.000911]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000911]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000912]   2 base 0000C0000000 mask FFFFE0000000 write-back
[    0.000913]   3 base 0000DF000000 mask FFFFFF000000 uncachable
[    0.000913]   4 disabled
[    0.000913]   5 disabled
[    0.000914]   6 disabled
[    0.000914]   7 disabled
[    0.000915] TOM2: 0000000420000000 aka 16896M
[    0.001331] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.001402] total RAM covered: 3568M
[    0.001849] Found optimal setting for mtrr clean up
[    0.001850]  gran_size: 64K 	chunk_size: 1G 	num_reg: 3  	lose cover RAM: 0G
[    0.001963] e820: update [mem 0xdf000000-0xffffffff] usable ==> reserved
[    0.001967] last_pfn = 0xdf000 max_arch_pfn = 0x400000000
[    0.005198] esrt: Reserving ESRT space from 0x00000000d96dc598 to 0x00000000d96dc5d0.
[    0.005207] check: Scanning 1 areas for low memory corruption
[    0.005210] Using GB pages for direct mapping
[    0.005212] BRK [0x175e01000, 0x175e01fff] PGTABLE
[    0.005213] BRK [0x175e02000, 0x175e02fff] PGTABLE
[    0.005214] BRK [0x175e03000, 0x175e03fff] PGTABLE
[    0.005253] BRK [0x175e04000, 0x175e04fff] PGTABLE
[    0.005254] BRK [0x175e05000, 0x175e05fff] PGTABLE
[    0.005430] BRK [0x175e06000, 0x175e06fff] PGTABLE
[    0.005529] BRK [0x175e07000, 0x175e07fff] PGTABLE
[    0.005573] BRK [0x175e08000, 0x175e08fff] PGTABLE
[    0.005622] BRK [0x175e09000, 0x175e09fff] PGTABLE
[    0.005703] BRK [0x175e0a000, 0x175e0afff] PGTABLE
[    0.005771] BRK [0x175e0b000, 0x175e0bfff] PGTABLE
[    0.005881] BRK [0x175e0c000, 0x175e0cfff] PGTABLE
[    0.005933] RAMDISK: [mem 0x33323000-0x35988fff]
[    0.005940] ACPI: Early table checksum verification disabled
[    0.005943] ACPI: RSDP 0x00000000DD01A000 000024 (v02 ALASKA)
[    0.005945] ACPI: XSDT 0x00000000DD01A090 0000A4 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.005949] ACPI: FACP 0x00000000DD020078 000114 (v06 ALASKA A M I    01072009 AMI  00010013)
[    0.005952] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20181213/tbfadt-624)
[    0.005956] ACPI: DSDT 0x00000000DD01A1D0 005EA2 (v02 ALASKA A M I    01072009 INTL 20120913)
[    0.005958] ACPI: FACS 0x00000000DD3D2E00 000040
[    0.005959] ACPI: APIC 0x00000000DD020190 0000DE (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.005961] ACPI: FPDT 0x00000000DD020270 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.005963] ACPI: FIDT 0x00000000DD0202B8 00009C (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.005965] ACPI: SSDT 0x00000000DD020358 008C4C (v02                 00000002 MSFT 04000000)
[    0.005967] ACPI: SRAT 0x00000000DD028FA8 0000F0 (v03 AMD    AmdTable 00000001 AMD  00000001)
[    0.005968] ACPI: CRAT 0x00000000DD029098 000BD0 (v01 AMD    AmdTable 00000001 AMD  00000001)
[    0.005970] ACPI: CDIT 0x00000000DD029C68 000029 (v01 AMD    AmdTable 00000001 AMD  00000001)
[    0.005972] ACPI: SSDT 0x00000000DD029C98 0017E1 (v01 AMD    AOD      00000001 INTL 20120913)
[    0.005974] ACPI: MCFG 0x00000000DD02B480 00003C (v01 ALASKA A M I    01072009 MSFT 00010013)
[    0.005976] ACPI: HPET 0x00000000DD02B4C0 000038 (v01 ALASKA A M I    01072009 AMI  00000005)
[    0.005977] ACPI: SSDT 0x00000000DD02B4F8 000024 (v01 AMDFCH FCHZP    00001000 INTL 20120913)
[    0.005979] ACPI: UEFI 0x00000000DD02B520 000042 (v01                 00000000      00000000)
[    0.005981] ACPI: IVRS 0x00000000DD02B568 0000D0 (v02                 00000001 AMD  00000000)
[    0.005983] ACPI: SSDT 0x00000000DD02B638 0000F8 (v01                 00001000 INTL 20120913)
[    0.005984] ACPI: SSDT 0x00000000DD02B730 001664 (v01 AMD    CPMCMN   00000001 INTL 20120913)
[    0.005991] ACPI: Local APIC address 0xfee00000
[    0.005993] system APIC only can use physical flat
[    0.005994] Setting APIC routing to physical flat.
[    0.006017] SRAT: PXM 0 -> APIC 0x00 -> Node 0
[    0.006018] SRAT: PXM 0 -> APIC 0x01 -> Node 0
[    0.006018] SRAT: PXM 0 -> APIC 0x02 -> Node 0
[    0.006019] SRAT: PXM 0 -> APIC 0x03 -> Node 0
[    0.006019] SRAT: PXM 0 -> APIC 0x06 -> Node 0
[    0.006019] SRAT: PXM 0 -> APIC 0x07 -> Node 0
[    0.006020] SRAT: PXM 0 -> APIC 0x08 -> Node 0
[    0.006020] SRAT: PXM 0 -> APIC 0x09 -> Node 0
[    0.006020] SRAT: PXM 0 -> APIC 0x0a -> Node 0
[    0.006021] SRAT: PXM 0 -> APIC 0x0b -> Node 0
[    0.006021] SRAT: PXM 0 -> APIC 0x0c -> Node 0
[    0.006021] SRAT: PXM 0 -> APIC 0x0d -> Node 0
[    0.006084] No NUMA configuration found
[    0.006084] Faking a node at [mem 0x0000000000000000-0x000000041f37ffff]
[    0.006090] NODE_DATA(0) allocated [mem 0x41f355000-0x41f37ffff]
[    0.006250] Zone ranges:
[    0.006250]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.006251]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.006252]   Normal   [mem 0x0000000100000000-0x000000041f37ffff]
[    0.006252]   Device   empty
[    0.006253] Movable zone start for each node
[    0.006255] Early memory node ranges
[    0.006255]   node   0: [mem 0x0000000000001000-0x000000000009ffff]
[    0.006256]   node   0: [mem 0x0000000000100000-0x0000000001d7ffff]
[    0.006256]   node   0: [mem 0x0000000002000000-0x00000000db5c8fff]
[    0.006256]   node   0: [mem 0x00000000dcbc9000-0x00000000dd019fff]
[    0.006257]   node   0: [mem 0x00000000de3e9000-0x00000000deffffff]
[    0.006257]   node   0: [mem 0x0000000100000000-0x000000041f37ffff]
[    0.006423] Zeroed struct page in unavailable ranges: 15536 pages
[    0.006424] Initmem setup node 0 [mem 0x0000000000001000-0x000000041f37ffff]
[    0.006425] On node 0 totalpages: 4175568
[    0.006426]   DMA zone: 64 pages used for memmap
[    0.006426]   DMA zone: 27 pages reserved
[    0.006427]   DMA zone: 3999 pages, LIFO batch:0
[    0.006488]   DMA32 zone: 14031 pages used for memmap
[    0.006488]   DMA32 zone: 897969 pages, LIFO batch:63
[    0.020545]   Normal zone: 51150 pages used for memmap
[    0.020546]   Normal zone: 3273600 pages, LIFO batch:63
[    0.069748] ACPI: PM-Timer IO Port: 0x808
[    0.069750] ACPI: Local APIC address 0xfee00000
[    0.069752] system APIC only can use physical flat
[    0.069756] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.069767] IOAPIC[0]: apic_id 13, version 33, address 0xfec00000, GSI 0-23
[    0.069770] IOAPIC[1]: apic_id 14, version 33, address 0xfec01000, GSI 24-55
[    0.069772] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.069773] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.069774] ACPI: IRQ0 used by override.
[    0.069774] ACPI: IRQ9 used by override.
[    0.069775] Using ACPI (MADT) for SMP configuration information
[    0.069776] ACPI: HPET id: 0x10228201 base: 0xfed00000
[    0.069780] smpboot: Allowing 16 CPUs, 4 hotplug CPUs
[    0.069800] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.069801] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.069802] PM: Registered nosave memory: [mem 0x01d80000-0x01ffffff]
[    0.069803] PM: Registered nosave memory: [mem 0xdb5c9000-0xdcbc8fff]
[    0.069804] PM: Registered nosave memory: [mem 0xdd01a000-0xdd3e8fff]
[    0.069804] PM: Registered nosave memory: [mem 0xdd3e9000-0xde2e8fff]
[    0.069805] PM: Registered nosave memory: [mem 0xde2e9000-0xde3e8fff]
[    0.069806] PM: Registered nosave memory: [mem 0xdf000000-0xdfffffff]
[    0.069806] PM: Registered nosave memory: [mem 0xe0000000-0xf7ffffff]
[    0.069806] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.069807] PM: Registered nosave memory: [mem 0xfc000000-0xfdefffff]
[    0.069807] PM: Registered nosave memory: [mem 0xfdf00000-0xfdffffff]
[    0.069807] PM: Registered nosave memory: [mem 0xfe000000-0xfe9fffff]
[    0.069807] PM: Registered nosave memory: [mem 0xfea00000-0xfea0ffff]
[    0.069808] PM: Registered nosave memory: [mem 0xfea10000-0xfeb7ffff]
[    0.069808] PM: Registered nosave memory: [mem 0xfeb80000-0xfec01fff]
[    0.069808] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[    0.069809] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[    0.069809] PM: Registered nosave memory: [mem 0xfec11000-0xfec2ffff]
[    0.069809] PM: Registered nosave memory: [mem 0xfec30000-0xfec30fff]
[    0.069810] PM: Registered nosave memory: [mem 0xfec31000-0xfecfffff]
[    0.069810] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[    0.069810] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[    0.069811] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[    0.069811] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[    0.069811] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[    0.069812] PM: Registered nosave memory: [mem 0xfed90000-0xfedc1fff]
[    0.069812] PM: Registered nosave memory: [mem 0xfedc2000-0xfedcffff]
[    0.069812] PM: Registered nosave memory: [mem 0xfedd0000-0xfedd3fff]
[    0.069812] PM: Registered nosave memory: [mem 0xfedd4000-0xfedd5fff]
[    0.069813] PM: Registered nosave memory: [mem 0xfedd6000-0xfedfffff]
[    0.069813] PM: Registered nosave memory: [mem 0xfee00000-0xfeefffff]
[    0.069813] PM: Registered nosave memory: [mem 0xfef00000-0xfeffffff]
[    0.069814] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.069815] [mem 0xe0000000-0xf7ffffff] available for PCI devices
[    0.069816] Booting paravirtualized kernel on bare hardware
[    0.069819] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.069827] random: get_random_bytes called from start_kernel+0x97/0x516 with crng_init=0
[    0.069833] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:16 nr_cpu_ids:16 nr_node_ids:1
[    0.070374] percpu: Embedded 47 pages/cpu s155648 r8192 d28672 u262144
[    0.070379] pcpu-alloc: s155648 r8192 d28672 u262144 alloc=1*2097152
[    0.070380] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15 
[    0.070401] Built 1 zonelists, mobility grouping on.  Total pages: 4110296
[    0.070401] Policy zone: Normal
[    0.070402] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.0.0-31-generic root=UUID=44899cbb-c047-4eed-914e-2e6e7230c525 ro quiet splash vt.handoff=1
[    0.076256] Calgary: detecting Calgary via BIOS EBDA area
[    0.076257] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.109717] Memory: 16256112K/16702272K available (14339K kernel code, 2335K rwdata, 4404K rodata, 2588K init, 5192K bss, 446160K reserved, 0K cma-reserved)
[    0.109867] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[    0.109874] ftrace: allocating 41614 entries in 163 pages
[    0.121842] rcu: Hierarchical RCU implementation.
[    0.121843] rcu: 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=16.
[    0.121843] 	Tasks RCU enabled.
[    0.121844] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.121844] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[    0.123895] NR_IRQS: 524544, nr_irqs: 1096, preallocated irqs: 16
[    0.124081] vt handoff: transparent VT on vt#1
[    0.124084] Console: colour dummy device 80x25
[    0.124087] printk: console [tty0] enabled
[    0.124099] ACPI: Core revision 20181213
[    0.124240] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[    0.124253] hpet clockevent registered
[    0.124256] APIC: Switch to symmetric I/O mode setup
[    0.194055] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.212256] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x7350666f237, max_idle_ns: 881590617012 ns
[    0.212264] Calibrating delay loop (skipped), value calculated using timer frequency.. 7999.91 BogoMIPS (lpj=15999824)
[    0.212265] pid_max: default: 32768 minimum: 301
[    0.214395] LSM: Security Framework initializing
[    0.214402] Yama: becoming mindful.
[    0.214423] AppArmor: AppArmor initialized
[    0.216393] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.217400] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.217448] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.217478] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.217688] LVT offset 1 assigned for vector 0xf9
[    0.217794] LVT offset 2 assigned for vector 0xf4
[    0.217804] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 512
[    0.217805] Last level dTLB entries: 4KB 1536, 2MB 1536, 4MB 768, 1GB 0
[    0.217806] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.217807] Spectre V2 : Mitigation: Full AMD retpoline
[    0.217807] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.217808] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.217974] Freeing SMP alternatives memory: 36K
[    0.328585] smpboot: CPU0: AMD Ryzen 5 1600X Six-Core Processor (family: 0x17, model: 0x1, stepping: 0x1)
[    0.328665] Performance Events: Fam17h core perfctr, AMD PMU driver.
[    0.328669] ... version:                0
[    0.328669] ... bit width:              48
[    0.328669] ... generic registers:      6
[    0.328669] ... value mask:             0000ffffffffffff
[    0.328670] ... max period:             00007fffffffffff
[    0.328670] ... fixed-purpose events:   0
[    0.328670] ... event mask:             000000000000003f
[    0.328695] rcu: Hierarchical SRCU implementation.
[    0.329197] random: crng done (trusting CPU's manufacturer)
[    0.329249] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.329355] smp: Bringing up secondary CPUs ...
[    0.329425] x86: Booting SMP configuration:
[    0.329426] .... node  #0, CPUs:        #1  #2  #3  #4  #5  #6  #7  #8  #9 #10 #11
[    0.352294] smp: Brought up 1 node, 12 CPUs
[    0.352294] smpboot: Max logical packages: 2
[    0.352294] smpboot: Total of 12 processors activated (95998.94 BogoMIPS)
[    0.353199] devtmpfs: initialized
[    0.353199] x86/mm: Memory block size: 128MB
[    0.353199] PM: Registering ACPI NVS region [mem 0xdd01a000-0xdd3e8fff] (3993600 bytes)
[    0.356276] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.356279] futex hash table entries: 4096 (order: 6, 262144 bytes)
[    0.356343] pinctrl core: initialized pinctrl subsystem
[    0.356413] RTC time: 11:37:27, date: 2019-10-12
[    0.356536] NET: Registered protocol family 16
[    0.356587] audit: initializing netlink subsys (disabled)
[    0.356595] audit: type=2000 audit(1570880247.168:1): state=initialized audit_enabled=0 res=1
[    0.356595] EISA bus registered
[    0.356595] cpuidle: using governor ladder
[    0.356595] cpuidle: using governor menu
[    0.356595] ACPI: bus type PCI registered
[    0.356595] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.356595] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.356595] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.356595] pmd_set_huge: Cannot satisfy [mem 0xf8000000-0xf8200000] with a huge-page mapping due to MTRR override.
[    0.356595] PCI: Using configuration type 1 for base access
[    0.357290] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.357290] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.357290] ACPI: Added _OSI(Module Device)
[    0.357290] ACPI: Added _OSI(Processor Device)
[    0.357290] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.357290] ACPI: Added _OSI(Processor Aggregator Device)
[    0.357290] ACPI: Added _OSI(Linux-Dell-Video)
[    0.357290] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.357290] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.360300] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.365972] ACPI: 6 ACPI AML tables successfully acquired and loaded
[    0.370179] ACPI: Interpreter enabled
[    0.370191] ACPI: (supports S0 S3 S4 S5)
[    0.370192] ACPI: Using IOAPIC for interrupt routing
[    0.370302] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.370582] ACPI: Enabled 2 GPEs in block 00 to 1F
[    0.377230] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.377233] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.377381] acpi PNP0A08:00: _OSC: platform does not support [SHPCHotplug LTR]
[    0.377520] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.377529] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.377841] PCI host bridge to bus 0000:00
[    0.377842] pci_bus 0000:00: root bus resource [io  0x0000-0x03af window]
[    0.377843] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7 window]
[    0.377845] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df window]
[    0.377846] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.377847] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.377847] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.377848] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfec2ffff window]
[    0.377849] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]
[    0.377850] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.377855] pci 0000:00:00.0: [1022:1450] type 00 class 0x060000
[    0.377926] pci 0000:00:00.2: [1022:1451] type 00 class 0x080600
[    0.378007] pci 0000:00:01.0: [1022:1452] type 00 class 0x060000
[    0.378070] pci 0000:00:01.3: [1022:1453] type 01 class 0x060400
[    0.378113] pci 0000:00:01.3: PME# supported from D0 D3hot D3cold
[    0.378178] pci 0000:00:02.0: [1022:1452] type 00 class 0x060000
[    0.378242] pci 0000:00:03.0: [1022:1452] type 00 class 0x060000
[    0.378303] pci 0000:00:03.1: [1022:1453] type 01 class 0x060400
[    0.378365] pci 0000:00:03.1: PME# supported from D0 D3hot D3cold
[    0.378436] pci 0000:00:04.0: [1022:1452] type 00 class 0x060000
[    0.378505] pci 0000:00:07.0: [1022:1452] type 00 class 0x060000
[    0.378566] pci 0000:00:07.1: [1022:1454] type 01 class 0x060400
[    0.378583] pci 0000:00:07.1: enabling Extended Tags
[    0.378604] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold
[    0.378664] pci 0000:00:08.0: [1022:1452] type 00 class 0x060000
[    0.378724] pci 0000:00:08.1: [1022:1454] type 01 class 0x060400
[    0.378742] pci 0000:00:08.1: enabling Extended Tags
[    0.378764] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold
[    0.378840] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500
[    0.378948] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100
[    0.379061] pci 0000:00:18.0: [1022:1460] type 00 class 0x060000
[    0.379110] pci 0000:00:18.1: [1022:1461] type 00 class 0x060000
[    0.379158] pci 0000:00:18.2: [1022:1462] type 00 class 0x060000
[    0.379207] pci 0000:00:18.3: [1022:1463] type 00 class 0x060000
[    0.379256] pci 0000:00:18.4: [1022:1464] type 00 class 0x060000
[    0.379304] pci 0000:00:18.5: [1022:1465] type 00 class 0x060000
[    0.379352] pci 0000:00:18.6: [1022:1466] type 00 class 0x060000
[    0.379399] pci 0000:00:18.7: [1022:1467] type 00 class 0x060000
[    0.379494] pci 0000:03:00.0: [1022:43bb] type 00 class 0x0c0330
[    0.379514] pci 0000:03:00.0: reg 0x10: [mem 0xfd7a0000-0xfd7a7fff 64bit]
[    0.379588] pci 0000:03:00.0: PME# supported from D3hot D3cold
[    0.379652] pci 0000:03:00.1: [1022:43b7] type 00 class 0x010601
[    0.379695] pci 0000:03:00.1: reg 0x24: [mem 0xfd780000-0xfd79ffff]
[    0.379701] pci 0000:03:00.1: reg 0x30: [mem 0xfd700000-0xfd77ffff pref]
[    0.379738] pci 0000:03:00.1: PME# supported from D3hot D3cold
[    0.379782] pci 0000:03:00.2: [1022:43b2] type 01 class 0x060400
[    0.379852] pci 0000:03:00.2: PME# supported from D3hot D3cold
[    0.379924] pci 0000:00:01.3: PCI bridge to [bus 03-22]
[    0.379926] pci 0000:00:01.3:   bridge window [io  0xd000-0xefff]
[    0.379928] pci 0000:00:01.3:   bridge window [mem 0xfd500000-0xfd7fffff]
[    0.379978] pci 0000:04:00.0: [1022:43b4] type 01 class 0x060400
[    0.380061] pci 0000:04:00.0: PME# supported from D3hot D3cold
[    0.380120] pci 0000:04:01.0: [1022:43b4] type 01 class 0x060400
[    0.380203] pci 0000:04:01.0: PME# supported from D3hot D3cold
[    0.380266] pci 0000:04:04.0: [1022:43b4] type 01 class 0x060400
[    0.380350] pci 0000:04:04.0: PME# supported from D3hot D3cold
[    0.380419] pci 0000:03:00.2: PCI bridge to [bus 04-22]
[    0.380423] pci 0000:03:00.2:   bridge window [io  0xd000-0xefff]
[    0.380425] pci 0000:03:00.2:   bridge window [mem 0xfd500000-0xfd6fffff]
[    0.380476] pci 0000:1f:00.0: [1b21:1080] type 01 class 0x060400
[    0.380649] pci 0000:1f:00.0: supports D1 D2
[    0.380650] pci 0000:1f:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.392281] pci 0000:04:00.0: PCI bridge to [bus 1f-20]
[    0.392286] pci 0000:04:00.0:   bridge window [io  0xe000-0xefff]
[    0.392289] pci 0000:04:00.0:   bridge window [mem 0xfd600000-0xfd6fffff]
[    0.392355] pci_bus 0000:20: extended config space not accessible
[    0.392382] pci 0000:20:00.0: [10ec:8169] type 00 class 0x020000
[    0.392414] pci 0000:20:00.0: reg 0x10: [io  0xe000-0xe0ff]
[    0.392432] pci 0000:20:00.0: reg 0x14: [mem 0xfd620000-0xfd6200ff]
[    0.392513] pci 0000:20:00.0: reg 0x30: [mem 0xfd600000-0xfd61ffff pref]
[    0.392570] pci 0000:20:00.0: supports D1 D2
[    0.392571] pci 0000:20:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.392686] pci 0000:1f:00.0: PCI bridge to [bus 20]
[    0.392695] pci 0000:1f:00.0:   bridge window [io  0xe000-0xefff]
[    0.392700] pci 0000:1f:00.0:   bridge window [mem 0xfd600000-0xfd6fffff]
[    0.392767] pci 0000:21:00.0: [10ec:8168] type 00 class 0x020000
[    0.392807] pci 0000:21:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.392841] pci 0000:21:00.0: reg 0x18: [mem 0xfd504000-0xfd504fff 64bit]
[    0.392863] pci 0000:21:00.0: reg 0x20: [mem 0xfd500000-0xfd503fff 64bit]
[    0.392997] pci 0000:21:00.0: supports D1 D2
[    0.392998] pci 0000:21:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.393161] pci 0000:04:01.0: PCI bridge to [bus 21]
[    0.393165] pci 0000:04:01.0:   bridge window [io  0xd000-0xdfff]
[    0.393167] pci 0000:04:01.0:   bridge window [mem 0xfd500000-0xfd5fffff]
[    0.393201] pci 0000:04:04.0: PCI bridge to [bus 22]
[    0.393271] pci 0000:23:00.0: [10de:1c03] type 00 class 0x030000
[    0.393297] pci 0000:23:00.0: reg 0x10: [mem 0xfc000000-0xfcffffff]
[    0.393309] pci 0000:23:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.393322] pci 0000:23:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.393330] pci 0000:23:00.0: reg 0x24: [io  0xf000-0xf07f]
[    0.393338] pci 0000:23:00.0: reg 0x30: [mem 0xfd000000-0xfd07ffff pref]
[    0.393354] pci 0000:23:00.0: BAR 3: assigned to efifb
[    0.393455] pci 0000:23:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:03.1 (capable of 126.016 Gb/s with 8 GT/s x16 link)
[    0.393489] pci 0000:23:00.1: [10de:10f1] type 00 class 0x040300
[    0.393508] pci 0000:23:00.1: reg 0x10: [mem 0xfd080000-0xfd083fff]
[    0.393682] pci 0000:00:03.1: PCI bridge to [bus 23]
[    0.393685] pci 0000:00:03.1:   bridge window [io  0xf000-0xffff]
[    0.393687] pci 0000:00:03.1:   bridge window [mem 0xfc000000-0xfd0fffff]
[    0.393690] pci 0000:00:03.1:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.393724] pci 0000:24:00.0: [1022:145a] type 00 class 0x130000
[    0.393746] pci 0000:24:00.0: enabling Extended Tags
[    0.393797] pci 0000:24:00.2: [1022:1456] type 00 class 0x108000
[    0.393809] pci 0000:24:00.2: reg 0x18: [mem 0xfd300000-0xfd3fffff]
[    0.393816] pci 0000:24:00.2: reg 0x24: [mem 0xfd400000-0xfd401fff]
[    0.393821] pci 0000:24:00.2: enabling Extended Tags
[    0.393876] pci 0000:24:00.3: [1022:145c] type 00 class 0x0c0330
[    0.393887] pci 0000:24:00.3: reg 0x10: [mem 0xfd200000-0xfd2fffff 64bit]
[    0.393904] pci 0000:24:00.3: enabling Extended Tags
[    0.393926] pci 0000:24:00.3: PME# supported from D0 D3hot D3cold
[    0.393970] pci 0000:00:07.1: PCI bridge to [bus 24]
[    0.393973] pci 0000:00:07.1:   bridge window [mem 0xfd200000-0xfd4fffff]
[    0.394013] pci 0000:25:00.0: [1022:1455] type 00 class 0x130000
[    0.394037] pci 0000:25:00.0: enabling Extended Tags
[    0.394092] pci 0000:25:00.2: [1022:7901] type 00 class 0x010601
[    0.394117] pci 0000:25:00.2: reg 0x24: [mem 0xfd808000-0xfd808fff]
[    0.394123] pci 0000:25:00.2: enabling Extended Tags
[    0.394148] pci 0000:25:00.2: PME# supported from D3hot D3cold
[    0.394183] pci 0000:25:00.3: [1022:1457] type 00 class 0x040300
[    0.394191] pci 0000:25:00.3: reg 0x10: [mem 0xfd800000-0xfd807fff]
[    0.394208] pci 0000:25:00.3: enabling Extended Tags
[    0.394231] pci 0000:25:00.3: PME# supported from D0 D3hot D3cold
[    0.394273] pci 0000:00:08.1: PCI bridge to [bus 25]
[    0.394276] pci 0000:00:08.1:   bridge window [mem 0xfd800000-0xfd8fffff]
[    0.394664] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[    0.394711] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[    0.394752] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[    0.394802] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[    0.394848] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[    0.394885] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[    0.394923] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[    0.394960] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[    0.396382] SCSI subsystem initialized
[    0.396397] libata version 3.00 loaded.
[    0.396397] pci 0000:23:00.0: vgaarb: setting as boot VGA device
[    0.396397] pci 0000:23:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.396397] pci 0000:23:00.0: vgaarb: bridge control possible
[    0.396397] vgaarb: loaded
[    0.396397] ACPI: bus type USB registered
[    0.396397] usbcore: registered new interface driver usbfs
[    0.396397] usbcore: registered new interface driver hub
[    0.396397] usbcore: registered new device driver usb
[    0.396397] pps_core: LinuxPPS API ver. 1 registered
[    0.396397] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.396397] PTP clock support registered
[    0.396397] EDAC MC: Ver: 3.0.0
[    0.396397] Registered efivars operations
[    0.416517] PCI: Using ACPI for IRQ routing
[    0.417802] PCI: pci_cache_line_size set to 64 bytes
[    0.417858] e820: reserve RAM buffer [mem 0x01d80000-0x03ffffff]
[    0.417859] e820: reserve RAM buffer [mem 0xdb5c9000-0xdbffffff]
[    0.417859] e820: reserve RAM buffer [mem 0xdd01a000-0xdfffffff]
[    0.417859] e820: reserve RAM buffer [mem 0xdf000000-0xdfffffff]
[    0.417860] e820: reserve RAM buffer [mem 0x41f380000-0x41fffffff]
[    0.417925] NetLabel: Initializing
[    0.417926] NetLabel:  domain hash size = 128
[    0.417926] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.417934] NetLabel:  unlabeled traffic allowed by default
[    0.420296] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.420298] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.422341] clocksource: Switched to clocksource tsc-early
[    0.428251] VFS: Disk quotas dquot_6.6.0
[    0.428265] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.428349] AppArmor: AppArmor Filesystem Enabled
[    0.428371] pnp: PnP ACPI init
[    0.428497] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.428500] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.428557] system 00:01: [mem 0xfeb80000-0xfebfffff] could not be reserved
[    0.428559] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.428646] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.428811] system 00:03: [io  0x0a00-0x0a0f] has been reserved
[    0.428812] system 00:03: [io  0x0a10-0x0a1f] has been reserved
[    0.428813] system 00:03: [io  0x0a20-0x0a2f] has been reserved
[    0.428814] system 00:03: [io  0x0a40-0x0a4f] has been reserved
[    0.428816] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.429085] pnp 00:04: [dma 0 disabled]
[    0.429169] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.429383] pnp 00:05: [dma 0 disabled]
[    0.429410] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.429593] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.429594] system 00:06: [io  0x040b] has been reserved
[    0.429595] system 00:06: [io  0x04d6] has been reserved
[    0.429596] system 00:06: [io  0x0c00-0x0c01] has been reserved
[    0.429596] system 00:06: [io  0x0c14] has been reserved
[    0.429597] system 00:06: [io  0x0c50-0x0c51] has been reserved
[    0.429598] system 00:06: [io  0x0c52] has been reserved
[    0.429599] system 00:06: [io  0x0c6c] has been reserved
[    0.429599] system 00:06: [io  0x0c6f] has been reserved
[    0.429600] system 00:06: [io  0x0cd0-0x0cd1] has been reserved
[    0.429600] system 00:06: [io  0x0cd2-0x0cd3] has been reserved
[    0.429601] system 00:06: [io  0x0cd4-0x0cd5] has been reserved
[    0.429602] system 00:06: [io  0x0cd6-0x0cd7] has been reserved
[    0.429602] system 00:06: [io  0x0cd8-0x0cdf] has been reserved
[    0.429603] system 00:06: [io  0x0800-0x089f] has been reserved
[    0.429604] system 00:06: [io  0x0b00-0x0b0f] has been reserved
[    0.429604] system 00:06: [io  0x0b20-0x0b3f] has been reserved
[    0.429605] system 00:06: [io  0x0900-0x090f] has been reserved
[    0.429605] system 00:06: [io  0x0910-0x091f] has been reserved
[    0.429607] system 00:06: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.429607] system 00:06: [mem 0xfec01000-0xfec01fff] could not be reserved
[    0.429608] system 00:06: [mem 0xfedc0000-0xfedc0fff] has been reserved
[    0.429609] system 00:06: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.429610] system 00:06: [mem 0xfed80000-0xfed8ffff] could not be reserved
[    0.429610] system 00:06: [mem 0xfec10000-0xfec10fff] has been reserved
[    0.429611] system 00:06: [mem 0xff000000-0xffffffff] has been reserved
[    0.429613] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.429939] pnp: PnP ACPI: found 7 devices
[    0.435554] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.435609] pci 0000:1f:00.0: PCI bridge to [bus 20]
[    0.435612] pci 0000:1f:00.0:   bridge window [io  0xe000-0xefff]
[    0.435619] pci 0000:1f:00.0:   bridge window [mem 0xfd600000-0xfd6fffff]
[    0.435633] pci 0000:04:00.0: PCI bridge to [bus 1f-20]
[    0.435634] pci 0000:04:00.0:   bridge window [io  0xe000-0xefff]
[    0.435638] pci 0000:04:00.0:   bridge window [mem 0xfd600000-0xfd6fffff]
[    0.435644] pci 0000:04:01.0: PCI bridge to [bus 21]
[    0.435645] pci 0000:04:01.0:   bridge window [io  0xd000-0xdfff]
[    0.435648] pci 0000:04:01.0:   bridge window [mem 0xfd500000-0xfd5fffff]
[    0.435654] pci 0000:04:04.0: PCI bridge to [bus 22]
[    0.435663] pci 0000:03:00.2: PCI bridge to [bus 04-22]
[    0.435664] pci 0000:03:00.2:   bridge window [io  0xd000-0xefff]
[    0.435667] pci 0000:03:00.2:   bridge window [mem 0xfd500000-0xfd6fffff]
[    0.435672] pci 0000:00:01.3: PCI bridge to [bus 03-22]
[    0.435673] pci 0000:00:01.3:   bridge window [io  0xd000-0xefff]
[    0.435675] pci 0000:00:01.3:   bridge window [mem 0xfd500000-0xfd7fffff]
[    0.435679] pci 0000:00:03.1: PCI bridge to [bus 23]
[    0.435680] pci 0000:00:03.1:   bridge window [io  0xf000-0xffff]
[    0.435682] pci 0000:00:03.1:   bridge window [mem 0xfc000000-0xfd0fffff]
[    0.435684] pci 0000:00:03.1:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.435688] pci 0000:00:07.1: PCI bridge to [bus 24]
[    0.435689] pci 0000:00:07.1:   bridge window [mem 0xfd200000-0xfd4fffff]
[    0.435693] pci 0000:00:08.1: PCI bridge to [bus 25]
[    0.435694] pci 0000:00:08.1:   bridge window [mem 0xfd800000-0xfd8fffff]
[    0.435698] pci_bus 0000:00: resource 4 [io  0x0000-0x03af window]
[    0.435699] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7 window]
[    0.435700] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df window]
[    0.435700] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.435701] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    0.435702] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    0.435703] pci_bus 0000:00: resource 10 [mem 0xe0000000-0xfec2ffff window]
[    0.435703] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window]
[    0.435704] pci_bus 0000:03: resource 0 [io  0xd000-0xefff]
[    0.435705] pci_bus 0000:03: resource 1 [mem 0xfd500000-0xfd7fffff]
[    0.435705] pci_bus 0000:04: resource 0 [io  0xd000-0xefff]
[    0.435706] pci_bus 0000:04: resource 1 [mem 0xfd500000-0xfd6fffff]
[    0.435706] pci_bus 0000:1f: resource 0 [io  0xe000-0xefff]
[    0.435707] pci_bus 0000:1f: resource 1 [mem 0xfd600000-0xfd6fffff]
[    0.435708] pci_bus 0000:20: resource 0 [io  0xe000-0xefff]
[    0.435708] pci_bus 0000:20: resource 1 [mem 0xfd600000-0xfd6fffff]
[    0.435709] pci_bus 0000:21: resource 0 [io  0xd000-0xdfff]
[    0.435709] pci_bus 0000:21: resource 1 [mem 0xfd500000-0xfd5fffff]
[    0.435710] pci_bus 0000:23: resource 0 [io  0xf000-0xffff]
[    0.435711] pci_bus 0000:23: resource 1 [mem 0xfc000000-0xfd0fffff]
[    0.435711] pci_bus 0000:23: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
[    0.435712] pci_bus 0000:24: resource 1 [mem 0xfd200000-0xfd4fffff]
[    0.435713] pci_bus 0000:25: resource 1 [mem 0xfd800000-0xfd8fffff]
[    0.435778] NET: Registered protocol family 2
[    0.435899] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes)
[    0.435933] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.436078] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.436197] TCP: Hash tables configured (established 131072 bind 65536)
[    0.436229] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.436263] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.436349] NET: Registered protocol family 1
[    0.436353] NET: Registered protocol family 44
[    0.436491] pci 0000:23:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.436501] pci 0000:23:00.1: Linked as a consumer to 0000:23:00.0
[    0.436633] PCI: CLS 64 bytes, default 64
[    0.436663] Unpacking initramfs...
[    0.797113] Freeing initrd memory: 39320K
[    0.797134] AMD-Vi: IOMMU performance counters supported
[    0.797226] pci 0000:00:00.2: can't derive routing for PCI INT A
[    0.797227] pci 0000:00:00.2: PCI INT A: not connected
[    0.797454] iommu: Adding device 0000:00:01.0 to group 0
[    0.797469] iommu: Adding device 0000:00:01.3 to group 0
[    0.797563] iommu: Adding device 0000:00:02.0 to group 1
[    0.797666] iommu: Adding device 0000:00:03.0 to group 2
[    0.797684] iommu: Adding device 0000:00:03.1 to group 2
[    0.797775] iommu: Adding device 0000:00:04.0 to group 3
[    0.797887] iommu: Adding device 0000:00:07.0 to group 4
[    0.797901] iommu: Adding device 0000:00:07.1 to group 4
[    0.797998] iommu: Adding device 0000:00:08.0 to group 5
[    0.798013] iommu: Adding device 0000:00:08.1 to group 5
[    0.798116] iommu: Adding device 0000:00:14.0 to group 6
[    0.798129] iommu: Adding device 0000:00:14.3 to group 6
[    0.798250] iommu: Adding device 0000:00:18.0 to group 7
[    0.798263] iommu: Adding device 0000:00:18.1 to group 7
[    0.798276] iommu: Adding device 0000:00:18.2 to group 7
[    0.798288] iommu: Adding device 0000:00:18.3 to group 7
[    0.798301] iommu: Adding device 0000:00:18.4 to group 7
[    0.798313] iommu: Adding device 0000:00:18.5 to group 7
[    0.798325] iommu: Adding device 0000:00:18.6 to group 7
[    0.798335] iommu: Adding device 0000:00:18.7 to group 7
[    0.798348] iommu: Adding device 0000:03:00.0 to group 0
[    0.798356] iommu: Adding device 0000:03:00.1 to group 0
[    0.798369] iommu: Adding device 0000:03:00.2 to group 0
[    0.798380] iommu: Adding device 0000:04:00.0 to group 0
[    0.798391] iommu: Adding device 0000:04:01.0 to group 0
[    0.798402] iommu: Adding device 0000:04:04.0 to group 0
[    0.798413] iommu: Adding device 0000:1f:00.0 to group 0
[    0.798421] iommu: Adding device 0000:20:00.0 to group 0
[    0.798440] iommu: Adding device 0000:21:00.0 to group 0
[    0.798456] iommu: Adding device 0000:23:00.0 to group 2
[    0.798467] iommu: Adding device 0000:23:00.1 to group 2
[    0.798476] iommu: Adding device 0000:24:00.0 to group 4
[    0.798485] iommu: Adding device 0000:24:00.2 to group 4
[    0.798493] iommu: Adding device 0000:24:00.3 to group 4
[    0.798501] iommu: Adding device 0000:25:00.0 to group 5
[    0.798510] iommu: Adding device 0000:25:00.2 to group 5
[    0.798518] iommu: Adding device 0000:25:00.3 to group 5
[    0.798736] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[    0.798737] AMD-Vi: Extended features (0xf77ef22294ada):
[    0.798737]  PPR NX GT IA GA PC GA_vAPIC
[    0.798739] AMD-Vi: Interrupt remapping enabled
[    0.798739] AMD-Vi: Virtual APIC enabled
[    0.798814] AMD-Vi: Lazy IO/TLB flushing enabled
[    0.799508] amd_uncore: AMD NB counters detected
[    0.799510] amd_uncore: AMD LLC counters detected
[    0.799687] perf/amd_iommu: Detected AMD IOMMU #0 (2 banks, 4 counters/bank).
[    0.799721] check: Scanning for low memory corruption every 60 seconds
[    0.800845] Initialise system trusted keyrings
[    0.800854] Key type blacklist registered
[    0.800879] workingset: timestamp_bits=36 max_order=22 bucket_order=0
[    0.801715] zbud: loaded
[    0.802047] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.802175] fuse init (API version 7.28)
[    0.821736] Key type asymmetric registered
[    0.821737] Asymmetric key parser 'x509' registered
[    0.821743] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    0.821778] io scheduler mq-deadline registered
[    0.822308] pcieport 0000:00:01.3: Signaling PME with IRQ 26
[    0.822321] iommu ivhd0: Event logged [INVALID_DEVICE_REQUEST device=00:00.0 pasid=0x00000 address=0xfffffffdf8000000 flags=0x0a00]
[    0.822391] pcieport 0000:00:03.1: Signaling PME with IRQ 27
[    0.822470] pcieport 0000:00:07.1: Signaling PME with IRQ 28
[    0.822599] pcieport 0000:00:08.1: Signaling PME with IRQ 30
[    0.823064] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.823100] efifb: probing for efifb
[    0.823112] efifb: framebuffer at 0xf1000000, using 3072k, total 3072k
[    0.823113] efifb: mode is 1024x768x32, linelength=4096, pages=1
[    0.823113] efifb: scrolling: redraw
[    0.823114] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.823189] Console: switching to colour frame buffer device 128x48
[    0.823200] fb0: EFI VGA frame buffer device
[    0.823273] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.823278] ACPI: Power Button [PWRB]
[    0.823298] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.823307] ACPI: Power Button [PWRF]
[    0.824041] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.844732] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.845797] Linux agpgart interface v0.103
[    0.848081] loop: module loaded
[    0.848204] libphy: Fixed MDIO Bus: probed
[    0.848205] tun: Universal TUN/TAP device driver, 1.6
[    0.848223] PPP generic driver version 2.4.2
[    0.848249] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.848251] ehci-pci: EHCI PCI platform driver
[    0.848259] ehci-platform: EHCI generic platform driver
[    0.848264] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.848265] ohci-pci: OHCI PCI platform driver
[    0.848271] ohci-platform: OHCI generic platform driver
[    0.848274] uhci_hcd: USB Universal Host Controller Interface driver
[    0.848333] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.848337] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1
[    0.903688] xhci_hcd 0000:03:00.0: hcc params 0x0200ef81 hci version 0x110 quirks 0x0000000048000410
[    0.903823] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    0.903824] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.903824] usb usb1: Product: xHCI Host Controller
[    0.903825] usb usb1: Manufacturer: Linux 5.0.0-31-generic xhci-hcd
[    0.903826] usb usb1: SerialNumber: 0000:03:00.0
[    0.903910] hub 1-0:1.0: USB hub found
[    0.903920] hub 1-0:1.0: 10 ports detected
[    0.904134] xhci_hcd 0000:03:00.0: xHCI Host Controller
[    0.904136] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 2
[    0.904137] xhci_hcd 0000:03:00.0: Host supports USB 3.0 SuperSpeed
[    0.904161] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.904175] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.00
[    0.904176] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.904177] usb usb2: Product: xHCI Host Controller
[    0.904177] usb usb2: Manufacturer: Linux 5.0.0-31-generic xhci-hcd
[    0.904178] usb usb2: SerialNumber: 0000:03:00.0
[    0.904228] hub 2-0:1.0: USB hub found
[    0.904233] hub 2-0:1.0: 4 ports detected
[    0.904405] xhci_hcd 0000:24:00.3: xHCI Host Controller
[    0.904407] xhci_hcd 0000:24:00.3: new USB bus registered, assigned bus number 3
[    0.904496] xhci_hcd 0000:24:00.3: hcc params 0x0270f665 hci version 0x100 quirks 0x0000000000000410
[    0.904583] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    0.904584] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.904585] usb usb3: Product: xHCI Host Controller
[    0.904585] usb usb3: Manufacturer: Linux 5.0.0-31-generic xhci-hcd
[    0.904586] usb usb3: SerialNumber: 0000:24:00.3
[    0.904639] hub 3-0:1.0: USB hub found
[    0.904644] hub 3-0:1.0: 4 ports detected
[    0.904767] xhci_hcd 0000:24:00.3: xHCI Host Controller
[    0.904768] xhci_hcd 0000:24:00.3: new USB bus registered, assigned bus number 4
[    0.904769] xhci_hcd 0000:24:00.3: Host supports USB 3.0 SuperSpeed
[    0.904777] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.904789] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.00
[    0.904790] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.904791] usb usb4: Product: xHCI Host Controller
[    0.904791] usb usb4: Manufacturer: Linux 5.0.0-31-generic xhci-hcd
[    0.904792] usb usb4: SerialNumber: 0000:24:00.3
[    0.904841] hub 4-0:1.0: USB hub found
[    0.904846] hub 4-0:1.0: 4 ports detected
[    0.904958] i8042: PNP: No PS/2 controller found.
[    0.904992] mousedev: PS/2 mouse device common for all mice
[    0.905066] rtc_cmos 00:02: RTC can wake from S4
[    0.905179] rtc_cmos 00:02: registered as rtc0
[    0.905189] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.905194] i2c /dev entries driver
[    0.905245] device-mapper: uevent: version 1.0.3
[    0.905279] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[    0.905290] platform eisa.0: Probing EISA bus 0
[    0.905292] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    0.905293] platform eisa.0: Cannot allocate resource for EISA slot 1
[    0.905294] platform eisa.0: Cannot allocate resource for EISA slot 2
[    0.905295] platform eisa.0: Cannot allocate resource for EISA slot 3
[    0.905295] platform eisa.0: Cannot allocate resource for EISA slot 4
[    0.905296] platform eisa.0: Cannot allocate resource for EISA slot 5
[    0.905297] platform eisa.0: Cannot allocate resource for EISA slot 6
[    0.905298] platform eisa.0: Cannot allocate resource for EISA slot 7
[    0.905298] platform eisa.0: Cannot allocate resource for EISA slot 8
[    0.905299] platform eisa.0: EISA: Detected 0 cards
[    0.905395] ledtrig-cpu: registered to indicate activity on CPUs
[    0.905397] EFI Variables Facility v0.08 2004-May-17
[    0.926874] NET: Registered protocol family 10
[    0.929871] Segment Routing with IPv6
[    0.929882] NET: Registered protocol family 17
[    0.929908] Key type dns_resolver registered
[    0.930495] mce: Using 23 MCE banks
[    0.930502] RAS: Correctable Errors collector initialized.
[    0.930518] microcode: CPU0: patch_level=0x0800111c
[    0.930520] microcode: CPU1: patch_level=0x0800111c
[    0.930524] microcode: CPU2: patch_level=0x0800111c
[    0.930527] microcode: CPU3: patch_level=0x0800111c
[    0.930528] microcode: CPU4: patch_level=0x0800111c
[    0.930531] microcode: CPU5: patch_level=0x0800111c
[    0.930536] microcode: CPU6: patch_level=0x0800111c
[    0.930540] microcode: CPU7: patch_level=0x0800111c
[    0.930544] microcode: CPU8: patch_level=0x0800111c
[    0.930547] microcode: CPU9: patch_level=0x0800111c
[    0.930552] microcode: CPU10: patch_level=0x0800111c
[    0.930555] microcode: CPU11: patch_level=0x0800111c
[    0.930576] microcode: Microcode Update Driver: v2.2.
[    0.930584] sched_clock: Marking stable (866378631, 64193750)->(933292155, -2719774)
[    0.930770] registered taskstats version 1
[    0.930782] Loading compiled-in X.509 certificates
[    0.931799] Loaded X.509 cert 'Build time autogenerated kernel key: f741e70acbe36b1401547c35fc32f1bcdd446f7a'
[    0.933976] Couldn't get size: 0x800000000000000e
[    0.933978] MODSIGN: Couldn't get UEFI db list
[    0.935066] Couldn't get size: 0x800000000000000e
[    0.935066] MODSIGN: Couldn't get UEFI MokListRT
[    0.936153] Couldn't get size: 0x800000000000000e
[    0.936153] MODSIGN: Couldn't get UEFI dbx list
[    0.936171] zswap: loaded using pool lzo/zbud
[    0.938954] Key type big_key registered
[    0.938957] Key type trusted registered
[    0.940259] Key type encrypted registered
[    0.940261] AppArmor: AppArmor sha1 policy hashing enabled
[    0.944630] ima: No TPM chip found, activating TPM-bypass!
[    0.944635] ima: Allocated hash algorithm: sha1
[    0.944639] No architecture policies found
[    0.944645] evm: Initialising EVM extended attributes:
[    0.944645] evm: security.selinux
[    0.944646] evm: security.SMACK64
[    0.944646] evm: security.SMACK64EXEC
[    0.944646] evm: security.SMACK64TRANSMUTE
[    0.944646] evm: security.SMACK64MMAP
[    0.944647] evm: security.apparmor
[    0.944647] evm: security.ima
[    0.944647] evm: security.capability
[    0.944648] evm: HMAC attrs: 0x1
[    0.944910]   Magic number: 7:672:630
[    0.944950] acpi PNP0C31:00: hash matches
[    0.945009] rtc_cmos 00:02: setting system clock to 2019-10-12T11:37:28 UTC (1570880248)
[    0.945166] powernow_k8: This CPU is not supported anymore, using acpi-cpufreq instead.
[    0.946666] Freeing unused decrypted memory: 2040K
[    0.946979] Freeing unused kernel image memory: 2588K
[    0.962441] Write protecting the kernel read-only data: 22528k
[    0.962808] Freeing unused kernel image memory: 2016K
[    0.963030] Freeing unused kernel image memory: 1740K
[    0.970866] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.970870] Run /init as init process
[    1.019957] ahci 0000:03:00.1: version 3.0
[    1.020114] ahci 0000:03:00.1: SSS flag set, parallel bus scan disabled
[    1.020156] ahci 0000:03:00.1: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0x33 impl SATA mode
[    1.020160] ahci 0000:03:00.1: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part sxs deso sadm sds apst 
[    1.020214] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    1.020216] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection
[    1.021825] libphy: r8169: probed
[    1.022192] r8169 0000:20:00.0 eth0: RTL8169sc/8110sc, 00:0a:cd:32:d1:45, XID 180, IRQ 33
[    1.022193] r8169 0000:20:00.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[    1.023336] scsi host0: ahci
[    1.023800] scsi host1: ahci
[    1.025882] scsi host2: ahci
[    1.026170] scsi host3: ahci
[    1.026294] scsi host4: ahci
[    1.026406] scsi host5: ahci
[    1.026535] scsi host6: ahci
[    1.030017] scsi host7: ahci
[    1.030070] ata1: SATA max UDMA/133 abar m131072@0xfd780000 port 0xfd780100 irq 41
[    1.030072] ata2: SATA max UDMA/133 abar m131072@0xfd780000 port 0xfd780180 irq 41
[    1.030073] ata3: DUMMY
[    1.030073] ata4: DUMMY
[    1.030074] ata5: SATA max UDMA/133 abar m131072@0xfd780000 port 0xfd780300 irq 41
[    1.030076] ata6: SATA max UDMA/133 abar m131072@0xfd780000 port 0xfd780380 irq 41
[    1.030076] ata7: DUMMY
[    1.030077] ata8: DUMMY
[    1.030255] ahci 0000:25:00.2: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[    1.030257] ahci 0000:25:00.2: flags: 64bit ncq sntf ilck led clo only pmp fbs pio 
[    1.030429] scsi host8: ahci
[    1.030475] ata9: SATA max UDMA/133 abar m4096@0xfd808000 port 0xfd808100 irq 43
[    1.035466] libphy: r8169: probed
[    1.035721] r8169 0000:21:00.0 eth1: RTL8168h/8111h, 4c:cc:6a:f4:3c:8b, XID 541, IRQ 44
[    1.035722] r8169 0000:21:00.0 eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.056875] r8169 0000:21:00.0 enp33s0: renamed from eth1
[    1.072319] r8169 0000:20:00.0 enp32s0: renamed from eth0
[    1.239750] usb 1-3: new high-speed USB device number 2 using xhci_hcd
[    1.329594] ata9: SATA link down (SStatus 0 SControl 300)
[    1.462061] usb 1-3: New USB device found, idVendor=0bda, idProduct=8813, bcdDevice= 0.00
[    1.462062] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.462063] usb 1-3: Product: 802.11ac NIC
[    1.462064] usb 1-3: Manufacturer: Realtek
[    1.462065] usb 1-3: SerialNumber: 123456
[    1.484663] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.488560] ata1.00: ATA-9: SanDisk SDSSDHII240G, X31200RL, max UDMA/133
[    1.488562] ata1.00: 468862128 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    1.490059] ata1.00: configured for UDMA/133
[    1.490210] scsi 0:0:0:0: Direct-Access     ATA      SanDisk SDSSDHII 00RL PQ: 0 ANSI: 5
[    1.490357] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.490400] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
[    1.490414] sd 0:0:0:0: [sda] Write Protect is off
[    1.490415] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.490431] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.492106]  sda: sda1 sda2
[    1.492400] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.604661] usb 1-8: new low-speed USB device number 3 using xhci_hcd
[    1.816664] tsc: Refined TSC clocksource calibration: 3999.997 MHz
[    1.816674] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x7350b459580, max_idle_ns: 881591204237 ns
[    1.816705] clocksource: Switched to clocksource tsc
[    1.923681] usb 1-8: New USB device found, idVendor=1a2c, idProduct=0c21, bcdDevice= 1.10
[    1.923683] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.923684] usb 1-8: Product: USB Keyboard
[    1.923684] usb 1-8: Manufacturer: USB
[    1.964673] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.971193] ata2.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
[    1.971195] ata2.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[    1.977751] ata2.00: configured for UDMA/133
[    1.977919] scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG HD204UI  0001 PQ: 0 ANSI: 5
[    1.978091] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    1.978102] sd 1:0:0:0: [sdb] Write Protect is off
[    1.978103] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.978109] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.978126] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.014305]  sdb: sdb1 sdb3 < sdb5 >
[    2.014713] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.056667] usb 1-9: new full-speed USB device number 4 using xhci_hcd
[    2.425220] usb 1-9: New USB device found, idVendor=0738, idProduct=1704, bcdDevice= 1.10
[    2.425221] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.425222] usb 1-9: Product: Mad Catz R.A.T.TE
[    2.425223] usb 1-9: Manufacturer: Mad Catz
[    2.425224] usb 1-9: SerialNumber: D2001095
[    2.433955] hidraw: raw HID events driver (C) Jiri Kosina
[    2.452672] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.454824] ata5.00: ATAPI: TSSTcorp CDDVDW SH-S223C, me03, max UDMA/100
[    2.456745] ata5.00: configured for UDMA/100
[    2.460818] scsi 4:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S223C  me03 PQ: 0 ANSI: 5
[    2.508554] usbcore: registered new interface driver usbhid
[    2.508556] usbhid: USB HID core driver
[    2.510164] input: USB USB Keyboard as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.0/0003:1A2C:0C21.0001/input/input2
[    2.528830] sr 4:0:0:0: [sr0] scsi3-mmc drive: 52x/52x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.528832] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.529070] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    2.529123] sr 4:0:0:0: Attached scsi generic sg2 type 5
[    2.568775] hid-generic 0003:1A2C:0C21.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-8/input0
[    2.568953] input: USB USB Keyboard Mouse as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.1/0003:1A2C:0C21.0002/input/input3
[    2.569001] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.1/0003:1A2C:0C21.0002/input/input4
[    2.628780] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-8/1-8:1.1/0003:1A2C:0C21.0002/input/input5
[    2.628823] hid-generic 0003:1A2C:0C21.0002: input,hidraw1: USB HID v1.10 Mouse [USB USB Keyboard] on usb-0000:03:00.0-8/input1
[    2.628930] input: Mad Catz Mad Catz R.A.T.TE as /devices/pci0000:00/0000:00:01.3/0000:03:00.0/usb1/1-9/1-9:1.0/0003:0738:1704.0003/input/input6
[    2.628987] hid-generic 0003:0738:1704.0003: input,hidraw2: USB HID v1.11 Mouse [Mad Catz Mad Catz R.A.T.TE] on usb-0000:03:00.0-9/input0
[    2.629171] hid-generic 0003:0738:1704.0004: hiddev0,hidraw3: USB HID v1.11 Device [Mad Catz Mad Catz R.A.T.TE] on usb-0000:03:00.0-9/input1
[    2.845639] ata6: SATA link down (SStatus 0 SControl 300)
[   34.452661] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   34.456995] ata5.00: configured for UDMA/100
[   65.172659] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   65.176996] ata5.00: configured for UDMA/100
[   65.274958] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[   65.480054] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[   65.496643] systemd[1]: Detected architecture x86-64.
[   65.500519] systemd[1]: Set hostname to <Maamon>.
[   65.598375] systemd[1]: Created slice System Slice.
[   65.598470] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[   65.598500] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[   65.598506] systemd[1]: Reached target User and Group Name Lookups.
[   65.598511] systemd[1]: Reached target Remote File Systems.
[   65.598575] systemd[1]: Created slice User and Session Slice.
[   65.598611] systemd[1]: Listening on Syslog Socket.
[   65.606296] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[   65.622485] bpfilter: Loaded bpfilter_umh pid 427
[   65.623527] lp: driver loaded but no devices found
[   65.626196] ppdev: user-space parallel port driver
[   65.628362] parport_pc 00:04: reported by Plug and Play ACPI
[   65.628450] parport0: PC-style at 0x378, irq 5 [PCSPP]
[   65.657574] systemd-journald[416]: Received request to flush runtime journal from PID 1
[   65.688274] Adding 2097148k swap on /swapfile.  Priority:-2 extents:6 across:2260988k SSFS
[   65.716386] lp0: using parport0 (interrupt-driven).
[   65.883917] ccp 0000:24:00.2: enabling device (0000 -> 0002)
[   65.884694] ccp 0000:24:00.2: ccp enabled
[   65.884714] ccp 0000:24:00.2: psp initialization failed
[   65.884715] ccp 0000:24:00.2: enabled
[   65.922295] cryptd: max_cpu_qlen set to 1000
[   65.928242] AVX2 version of gcm_enc/dec engaged.
[   65.928244] AES CTR mode by8 optimization enabled
[   65.931753] IPMI message handler: version 39.2
[   65.933240] ipmi device interface
[   65.955540] snd_hda_intel 0000:23:00.1: Disabling MSI
[   65.955545] snd_hda_intel 0000:23:00.1: Handle vga_switcheroo audio client
[   65.955608] snd_hda_intel 0000:25:00.3: enabling device (0000 -> 0002)
[   66.004522] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   66.005417] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   66.009074] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC892: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[   66.009076] snd_hda_codec_realtek hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   66.009077] snd_hda_codec_realtek hdaudioC1D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   66.009077] snd_hda_codec_realtek hdaudioC1D0:    mono: mono_out=0x0
[   66.009078] snd_hda_codec_realtek hdaudioC1D0:    inputs:
[   66.009079] snd_hda_codec_realtek hdaudioC1D0:      Front Mic=0x19
[   66.009105] snd_hda_codec_realtek hdaudioC1D0:      Rear Mic=0x18
[   66.009105] snd_hda_codec_realtek hdaudioC1D0:      Line=0x1a
[   66.042839] PKCS#7 signature not signed with a trusted key
[   66.042863] 88XXau: loading out-of-tree module taints kernel.
[   66.042942] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input7
[   66.042979] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input8
[   66.043010] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input9
[   66.043040] input: HD-Audio Generic Line Out Front as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input10
[   66.043070] input: HD-Audio Generic Line Out Surround as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input11
[   66.043101] input: HD-Audio Generic Line Out CLFE as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input12
[   66.043133] input: HD-Audio Generic Line Out Side as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input13
[   66.043138] kvm: Nested Virtualization enabled
[   66.043142] kvm: Nested Paging enabled
[   66.043142] SVM: Virtual VMLOAD VMSAVE supported
[   66.043143] SVM: Virtual GIF supported
[   66.043166] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:08.1/0000:25:00.3/sound/card1/input14
[   66.127961] PKCS#7 signature not signed with a trusted key
[   66.127973] nvidia: module license 'NVIDIA' taints kernel.
[   66.127973] Disabling lock debugging due to kernel taint
[   66.141626] 88XXau: module verification failed: signature and/or required key missing - tainting kernel
[   66.141664] MCE: In-kernel MCE decoding enabled.
[   66.142871] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.142873] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.147806] nvidia-nvlink: Nvlink Core is being initialized, major device number 237
[   66.148131] nvidia 0000:23:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
[   66.247569] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  430.50  Thu Sep  5 22:36:31 CDT 2019
[   66.253463] PKCS#7 signature not signed with a trusted key
[   66.308803] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.308805] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.308903] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms  430.50  Thu Sep  5 22:39:50 CDT 2019
[   66.310958] PKCS#7 signature not signed with a trusted key
[   66.311563] [drm] [nvidia-drm] [GPU ID 0x00002300] Loading driver
[   66.311564] [drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:23:00.0 on minor 0
[   66.421149] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.421151] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.528692] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.528693] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.616710] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.616711] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.760923] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.760925] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.780314] PKCS#7 signature not signed with a trusted key
[   66.782550] nvidia-uvm: Loaded the UVM driver in 8 mode, major device number 235
[   66.795793] audit: type=1400 audit(1570880314.343:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=991 comm="apparmor_parser"
[   66.795956] audit: type=1400 audit(1570880314.343:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=989 comm="apparmor_parser"
[   66.796012] audit: type=1400 audit(1570880314.343:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=987 comm="apparmor_parser"
[   66.796014] audit: type=1400 audit(1570880314.343:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=987 comm="apparmor_parser"
[   66.796016] audit: type=1400 audit(1570880314.343:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=987 comm="apparmor_parser"
[   66.796810] audit: type=1400 audit(1570880314.347:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=988 comm="apparmor_parser"
[   66.796974] audit: type=1400 audit(1570880314.347:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=984 comm="apparmor_parser"
[   66.796977] audit: type=1400 audit(1570880314.347:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=984 comm="apparmor_parser"
[   66.796978] audit: type=1400 audit(1570880314.347:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=984 comm="apparmor_parser"
[   66.796980] audit: type=1400 audit(1570880314.347:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=984 comm="apparmor_parser"
[   66.908665] EDAC amd64: Node 0: DRAM ECC disabled.
[   66.908667] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   66.909462] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.1/0000:23:00.1/sound/card0/input15
[   66.909513] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.1/0000:23:00.1/sound/card0/input16
[   66.909553] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.1/0000:23:00.1/sound/card0/input17
[   66.909595] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.1/0000:23:00.1/sound/card0/input18
[   67.154969] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000c0000-0x000dffff window]
[   67.155073] caller os_map_kernel_space.part.12+0x74/0x90 [nvidia] mapping multiple BARs
[   67.229075] RTL8211B Gigabit Ethernet r8169-2000:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-2000:00, irq=IGNORE)
[   67.260521] EDAC amd64: Node 0: DRAM ECC disabled.
[   67.260522] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   67.264696] PKCS#7 signature not signed with a trusted key
[   67.269597] vboxdrv: Found 12 processor cores
[   67.292381] vboxdrv: TSC mode is Invariant, tentative frequency 3999996093 Hz
[   67.292382] vboxdrv: Successfully loaded version 5.2.32_Ubuntu (interface 0x00290001)
[   67.295755] PKCS#7 signature not signed with a trusted key
[   67.296007] VBoxNetFlt: Successfully started.
[   67.298590] PKCS#7 signature not signed with a trusted key
[   67.298772] VBoxNetAdp: Successfully started.
[   67.301475] PKCS#7 signature not signed with a trusted key
[   67.301676] VBoxPciLinuxInit
[   67.303773] vboxpci: IOMMU found
[   67.313562] r8169 0000:20:00.0 enp32s0: Link is Down
[   67.314940] Generic PHY r8169-2100:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-2100:00, irq=IGNORE)
[   67.423229] r8169 0000:21:00.0 enp33s0: Link is Down
[   67.484676] EDAC amd64: Node 0: DRAM ECC disabled.
[   67.484677] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   67.672652] EDAC amd64: Node 0: DRAM ECC disabled.
[   67.672653] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   67.816681] EDAC amd64: Node 0: DRAM ECC disabled.
[   67.816682] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   67.900727] EDAC amd64: Node 0: DRAM ECC disabled.
[   67.900729] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
                Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
                (Note that use of the override may cause unknown side effects.)
[   68.129402] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000c0000-0x000dffff window]
[   68.129503] caller os_map_kernel_space.part.12+0x74/0x90 [nvidia] mapping multiple BARs
[   69.998819] r8169 0000:20:00.0 enp32s0: Link is Up - 1Gbps/Full - flow control rx/tx
[   69.998828] IPv6: ADDRCONF(NETDEV_CHANGE): enp32s0: link becomes ready
[   70.504524] r8169 0000:21:00.0 enp33s0: Link is Up - 1Gbps/Full - flow control rx/tx
[   70.504533] IPv6: ADDRCONF(NETDEV_CHANGE): enp33s0: link becomes ready
[   72.965285] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000c0000-0x000dffff window]
[   72.965384] caller os_map_kernel_space.part.12+0x74/0x90 [nvidia] mapping multiple BARs
[   74.587727] usbcore: registered new interface driver rtl88xxau
[   74.589200] rtl88xxau 1-3:1.0 wlx00c0caa88ebf: renamed from wlan0
[   84.396263] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 24
[   84.456271] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 2
[   84.964250] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 36
[   85.024263] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 2
[   85.116264] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 2
[   85.176263] snd_hda_codec_hdmi hdaudioC0D0: HDMI: invalid ELD data byte 2
[   88.882417] [UFW BLOCK] IN=enp32s0 OUT= MAC= SRC=fe80:0000:0000:0000:97a6:aced:844b:b22b DST=ff02:0000:0000:0000:0000:0000:0000:0001 LEN=64 TC=0 HOPLIMIT=1 FLOWLBL=952639 PROTO=UDP SPT=8612 DPT=8612 LEN=24 
[   88.882436] [UFW BLOCK] IN=enp32s0 OUT= MAC= SRC=fe80:0000:0000:0000:97a6:aced:844b:b22b DST=ff02:0000:0000:0000:0000:0000:0000:0001 LEN=64 TC=0 HOPLIMIT=1 FLOWLBL=607952 PROTO=UDP SPT=8612 DPT=8610 LEN=24 
[   88.892527] [UFW BLOCK] IN=enp32s0 OUT= MAC= SRC=fe80:0000:0000:0000:97a6:aced:844b:b22b DST=ff02:0000:0000:0000:0000:0000:0000:0001 LEN=64 TC=0 HOPLIMIT=1 FLOWLBL=952639 PROTO=UDP SPT=8612 DPT=8612 LEN=24 
[   88.892545] [UFW BLOCK] IN=enp32s0 OUT= MAC= SRC=fe80:0000:0000:0000:97a6:aced:844b:b22b DST=ff02:0000:0000:0000:0000:0000:0000:0001 LEN=64 TC=0 HOPLIMIT=1 FLOWLBL=607952 PROTO=UDP SPT=8612 DPT=8610 LEN=24 
[   97.936307] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   97.940675] ata5.00: configured for UDMA/100
[   98.355641] rfkill: input handler disabled

moko138 · Le 12/10/2019, à 13:59

Maamon a écrit :

systemd-analyze blame
         10.585s packagekit.service
         10.347s apport-autoreport.service

Apport : à désactiver !
packagekit : Demande d'autres avis, mais je ne vois pas l'intérêt de lancer ce service dès le démarrage.

xubu1957 · Le 12/10/2019, à 14:06

Pour nettoyer les snaps :

sudo apt clean && snap list --all | awk 'BEGIN {print "#! /bin/sh\n"} ; /désactivé|disabled/ {print "snap remove "$1" --revision "$3"\n"} ; END {print "exit 0"}' > script && chmod +x script && ./script && rm script && echo && snap list --all && echo && df -Th | grep -Ev "tmpfs|squashfs"

> |RESOLU] snap nettoyage des versions désactivées.

Dernière modification par xubu1957 (Le 12/10/2019, à 14:08)

moko138 · Le 12/10/2019, à 14:10

dmesg
(...)
[    2.845639] ata6: SATA link down (SStatus 0 SControl 300)
[   34.452661] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   34.456995] ata5.00: configured for UDMA/100
[   65.172659] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

Deux trous de 30 secondes !
Bien vu, ylag !

Maamon, montre :

sudo lsblk -o name,fstype,label,size,mountpoint,uuid | grep -Ev "loop|sr[0-9]"

tail -n +7 /etc/fstab

echo ; cat /proc/swaps ; echo ; grep UUID /etc/initramfs-tools/conf.d/resume

malbo · Le 12/10/2019, à 14:15

Bonjour,
L'extrait du résultat de dmesg collé dans le post #12 de moko138 montre qu'il y a toujours un problème avec ata5 qui est ton graveur SH-S223C comme dans cette précédente discussion : https://forum.ubuntu-fr.org/viewtopic.php?id=2043872

ylag · Le 12/10/2019, à 14:19

@moko138:

Salut,

Concernant ton commentaire #10, sous toute réserve, je crois que ces services se chargent dans le "user space", après le chargement du noyau?

A+

Dernière modification par ylag (Le 12/10/2019, à 14:22)

Maamon · Le 12/10/2019, à 14:26

Dans l'ordre :

sudo lsblk -o name,fstype,label,size,mountpoint,uuid | grep -Ev "loop|sr[0-9]"
[sudo] Mot de passe de maamon : 
NAME   FSTYPE   LABEL   SIZE MOUNTPOINT                     UUID
sda                   223,6G                                
├─sda1 vfat             512M /boot/efi                      9A02-8480
└─sda2 ext4           223,1G /                              44899cbb-c047-4eed-914e-2e6e7230c525
sdb                     1,8T                                
├─sdb1 ext4           776,7G                                4df57cdc-69fd-4d99-81aa-13b7d4616ba8
├─sdb3                    1K                                
└─sdb5 ntfs             1,1T                                01D56CD238D67B50

tail -n +7 /etc/fstab
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
# / was on /dev/sda2 during installation
UUID=44899cbb-c047-4eed-914e-2e6e7230c525 /               ext4    errors=remount-ro 0       1
# /boot/efi was on /dev/sda1 during installation
UUID=9A02-8480  /boot/efi       vfat    umask=0077      0       1
/swapfile                                 none            swap    sw              0       0

echo ; cat /proc/swaps ; echo ; grep UUID /etc/initramfs-tools/conf.d/resume

Filename				Type		Size	Used	Priority
/swapfile                               file		2097148	0	-2

grep: /etc/initramfs-tools/conf.d/resume: Aucun fichier ou dossier de ce type

Ca y est, on est carrément rentré dans la partie ou je comprends plus rien ^^

Malbo, j'avais réglé le problème, apparemment il est revenu, je vais physiquement le débrancher, je ne m'en sert que très peu.

moko138 · Le 12/10/2019, à 14:27

ylag,
1) Je n'en sais rien. Mais je doute que 2 fois dix secondes tiennent dans

2.447s (userspace)

2) Cf. malbo ci-dessus.

Maamon · Le 12/10/2019, à 14:35

Bon, je viens de refaire la manip que m'avait suggéré Malbo à l'époque.

systemd-analyze time
Startup finished in 21.122s (firmware) + 3.986s (loader) + 3.445s (kernel) + 2.399s (userspace) = 30.954s
graphical.target reached after 2.396s in userspace

Apparemment le problème vient bien de là.
J'ai utilisé mon lecteur cd hier, ça a pu faire resurgir le problème ? je ne sais pas.
Si le problème revient trop souvent, je changerais de lecteur cd.
En tout cas merci à tous pour votre temps, le forum est vraiment top

ylag · Le 12/10/2019, à 16:13

Salut,

Maamon a écrit :

Bon, je viens de refaire la manip que m'avait suggéré Malbo à l'époque.

Voir aussi le commentaire #10 dans cette discussion: [Résolu] Démarrage lent, dsmeg, failed command: IDENTIFY PACKET DEVICE

A+

Dernière modification par ylag (Le 12/10/2019, à 16:13)

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 11/10/2019, à 22:44

Lenteur démarrage Kernel +1min [Résolu]

#2 Le 11/10/2019, à 23:41

Re : Lenteur démarrage Kernel +1min [Résolu]

#3 Le 12/10/2019, à 00:02

Re : Lenteur démarrage Kernel +1min [Résolu]

#4 Le 12/10/2019, à 01:28

Re : Lenteur démarrage Kernel +1min [Résolu]

#5 Le 12/10/2019, à 11:37

Re : Lenteur démarrage Kernel +1min [Résolu]

#6 Le 12/10/2019, à 11:43

Re : Lenteur démarrage Kernel +1min [Résolu]

#7 Le 12/10/2019, à 12:55

Re : Lenteur démarrage Kernel +1min [Résolu]

#8 Le 12/10/2019, à 13:41

Re : Lenteur démarrage Kernel +1min [Résolu]

#9 Le 12/10/2019, à 13:59

Re : Lenteur démarrage Kernel +1min [Résolu]

#10 Le 12/10/2019, à 14:06

Re : Lenteur démarrage Kernel +1min [Résolu]

#11 Le 12/10/2019, à 14:10

Re : Lenteur démarrage Kernel +1min [Résolu]

#12 Le 12/10/2019, à 14:15

Re : Lenteur démarrage Kernel +1min [Résolu]

#13 Le 12/10/2019, à 14:19

Re : Lenteur démarrage Kernel +1min [Résolu]

#14 Le 12/10/2019, à 14:26

Re : Lenteur démarrage Kernel +1min [Résolu]

#15 Le 12/10/2019, à 14:27

Re : Lenteur démarrage Kernel +1min [Résolu]

#16 Le 12/10/2019, à 14:35

Re : Lenteur démarrage Kernel +1min [Résolu]

#17 Le 12/10/2019, à 16:13

Re : Lenteur démarrage Kernel +1min [Résolu]

Pied de page des forums