Ubuntu-fr

Iz_no_goud

Problème lors du démarrage

Bonjour tout le monde,
Je viens de rencontrer un problème avec ma ubuntu.
Lorsque j'allume mon ordinateur et que ubuntu démarre; il reste bloqué au premier "loading module". Je dois alors reseter mon ordinateur pour que ça redémarre normalement. (Parfois, ubuntu reste bloqué plusieurs fois d'affilés, et à chaque fois, je dois redémarrer l'ordinateur)
Que faire pour que ce problème disparaisse ?
merci pour vos futures réponses

---

Ubuntu, c'est pas bien..................c'est génial :D

zeugme

Re : Problème lors du démarrage

Et il ne load aucun module ?
Meme en attendant ?

Que se passe t-il en session de secours ?

Que disent les logs system ?
/var/log

Iz_no_goud

Re : Problème lors du démarrage

Tout d'abord, merci de ton aide
1) Même en attendant, l'écran reste figé, et je peut rester là des heures, rien ne se passe
2)Je n'ai as de session de secours, comment faire pour l'avoir ?
3)comment voir ce que disent les /var/log  car dans ce répertoire, j'ai plein de fichiers
j'ai toujours fait un petit Dmesg, je te le montre:

[4294670.964000] ACPI: Subsystem revision 20050729
[4294670.981000] ACPI: Interpreter enabled
[4294670.981000] ACPI: Using IOAPIC for interrupt routing
[4294670.981000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294670.981000] PCI: Probing PCI hardware (bus 00)
[4294670.981000] ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
[4294670.989000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
[4294670.989000] Boot video device is 0000:01:00.0
[4294670.991000] PCI: Transparent bridge - 0000:00:14.4
[4294670.997000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294670.999000] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[4294670.999000] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[4294670.999000] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[4294670.999000] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[4294671.001000] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[4294671.001000] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[4294671.001000] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[4294671.001000] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[4294671.003000] burst-mode-ec-10-Aug
[4294671.003000] ACPI: Embedded Controller [EC0] (gpe 3)
[4294671.081000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
[4294671.083000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
[4294671.083000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[4294671.083000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[4294671.085000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294671.085000] pnp: PnP ACPI init
[4294671.101000] pnp: PnP ACPI: found 10 devices
[4294671.101000] PnPBIOS: Disabled by ACPI PNP
[4294671.101000] PCI: Using ACPI for IRQ routing
[4294671.101000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[4294671.145000] pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
[4294671.145000] pnp: 00:07: ioport range 0x1200-0x120f has been reserved
[4294671.145000] pnp: 00:07: ioport range 0x500-0x51f has been reserved
[4294671.145000] pnp: 00:07: ioport range 0x40b-0x40b has been reserved
[4294671.147000] audit: initializing netlink socket (disabled)
[4294671.147000] audit: initialized
[4294671.147000] VFS: Disk quotas dquot_6.5.1
[4294671.147000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294671.147000] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[4294671.147000] devfs: boot_options: 0x0
[4294671.147000] Initializing Cryptographic API
[4294671.147000] PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
[4294671.147000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[4294671.147000] pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS
[4294671.147000] assign_interrupt_mode Found MSI capability
[4294671.147000] Allocate Port Service[pcie00]
[4294671.147000] PCI: 0000:00:06.0 has unsupported PM cap regs version (3)
[4294671.147000] PCI: Setting latency timer of device 0000:00:06.0 to 64
[4294671.147000] pcie_portdrv_probe->Dev[5a38:1002] has invalid IRQ. Check vendor BIOS
[4294671.147000] assign_interrupt_mode Found MSI capability
[4294671.147000] Allocate Port Service[pcie00]
[4294671.147000] PCI: 0000:00:07.0 has unsupported PM cap regs version (3)
[4294671.147000] PCI: Setting latency timer of device 0000:00:07.0 to 64
[4294671.147000] pcie_portdrv_probe->Dev[5a39:1002] has invalid IRQ. Check vendor BIOS
[4294671.147000] assign_interrupt_mode Found MSI capability
[4294671.147000] Allocate Port Service[pcie00]
[4294671.147000] isapnp: Scanning for PnP cards...
[4294671.855000] isapnp: No Plug & Play device found
[4294671.885000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[4294671.903000] i8042.c: Detected active multiplexing controller, rev 1.1.
[4294671.909000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[4294671.911000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[4294671.913000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[4294671.913000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[4294671.915000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294671.915000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[4294671.915000] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294671.919000] ACPI: PCI Interrupt 0000:00:14.6[b] -> GSI 17 (level, low) -> IRQ 17
[4294671.919000] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[4294671.919000] io scheduler noop registered
[4294671.919000] io scheduler anticipatory registered
[4294671.919000] io scheduler deadline registered
[4294671.919000] io scheduler cfq registered
[4294671.919000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294671.923000] EISA: Probing bus 0 at eisa.0
[4294671.923000] Cannot allocate resource for EISA slot 1
[4294671.923000] Cannot allocate resource for EISA slot 8
[4294671.923000] EISA: Detected 0 cards.
[4294671.923000] NET: Registered protocol family 2
[4294671.943000] IP: routing cache hash table of 4096 buckets, 32Kbytes
[4294671.943000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[4294671.943000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[4294671.943000] TCP: Hash tables configured (established 16384 bind 16384)
[4294671.943000] NET: Registered protocol family 8
[4294671.943000] NET: Registered protocol family 20
[4294671.943000] ACPI wakeup devices:
[4294671.943000] LID0 SLPB OHC1 OHC2 EHCI  P2P MODM
[4294671.943000] ACPI: (supports S0 S3 S4 S5)
[4294671.943000] Freeing unused kernel memory: 224k freed
[4294671.965000] vga16fb: initializing
[4294671.965000] vga16fb: mapped to 0xc00a0000
[4294672.241000] Console: switching to colour frame buffer device 80x30
[4294672.241000] fb0: VGA16 VGA frame buffer device
[4294673.593000] Capability LSM initialized
[4294673.609000] NET: Registered protocol family 1
[4294673.631000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294673.631000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294673.631000] ACPI: bus type ide registered
[4294673.645000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[4294673.645000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
[4294673.645000] ATIIXP: chipset revision 0
[4294673.645000] ATIIXP: not 100% native mode: will probe irqs later
[4294673.645000]     ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio
[4294673.645000]     ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio
[4294673.645000] Probing IDE interface ide0...
[4294673.930000] hda: SAMSUNG MP0804H, ATA DISK drive
[4294674.556000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294674.558000] Probing IDE interface ide1...
[4294675.250000] hdc: Slimtype DVDRW SOSW-833S, ATAPI CD/DVD-ROM drive
[4294675.872000] ide1 at 0x170-0x177,0x376 on irq 15
[4294675.872000] Probing IDE interface ide2...
[4294676.397000] Probing IDE interface ide3...
[4294676.919000] Probing IDE interface ide4...
[4294677.441000] Probing IDE interface ide5...
[4294677.967000] hda: max request size: 1024KiB
[4294678.919000] hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
[4294678.919000] hda: cache flushes supported
[4294678.919000]  /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 > p3
[4294679.017000] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[4294679.017000] Uniform CD-ROM driver Revision: 3.20
[4294679.443000] Attempting manual resume
[4294679.445000] swsusp: Suspend partition has wrong signature?
[4294679.509000] usbcore: registered new driver usbfs
[4294679.509000] usbcore: registered new driver hub
[4294679.511000] ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[4294679.511000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
[4294679.511000] ohci_hcd 0000:00:13.0: PCI device 1002:4374 (ATI Technologies Inc)
[4294679.726000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[4294679.726000] ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0000000
[4294679.786000] hub 1-0:1.0: USB hub found
[4294679.786000] hub 1-0:1.0: 4 ports detected
[4294679.792000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
[4294679.792000] ohci_hcd 0000:00:13.1: PCI device 1002:4375 (ATI Technologies Inc)
[4294680.007000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[4294680.007000] ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0001000
[4294680.067000] hub 2-0:1.0: USB hub found
[4294680.067000] hub 2-0:1.0: 4 ports detected
[4294680.099000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
[4294680.099000] ehci_hcd 0000:00:13.2: PCI device 1002:4373 (ATI Technologies Inc)
[4294680.099000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[4294680.099000] ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0002000
[4294680.099000] ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[4294680.099000] hub 3-0:1.0: USB hub found
[4294680.099000] hub 3-0:1.0: 8 ports detected
[4294680.325000] r8169 Gigabit Ethernet driver 2.2LK loaded
[4294680.325000] ACPI: PCI Interrupt 0000:06:07.0[A] -> GSI 23 (level, low) -> IRQ 23
[4294680.329000] eth0: Identified chip type is 'RTL8169s/8110s'.
[4294680.329000] eth0: RTL8169 at 0xe0898400, 00:0a:e4:ee:14:2b, IRQ 23
[4294683.079000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[4294683.183000] ACPI: Thermal Zone [TZS0] (52 C)
[4294683.289000] ACPI: Thermal Zone [TZS1] (26 C)
[4294683.395000] ACPI: Thermal Zone [TZSV] (35 C)
[4294683.991000] Attempting manual resume
[4294683.991000] swsusp: Suspend partition has wrong signature?
[4294684.053000] kjournald starting.  Commit interval 5 seconds
[4294684.053000] EXT3-fs: mounted filesystem with ordered data mode.
[4294686.705000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294692.817000] Adding 1510036k swap on /dev/hda6.  Priority:-1 extents:1
[4294693.433000] EXT3 FS on hda3, internal journal
[4294705.951000] APIC error on CPU0: 00(40)
[4294708.626000] lp: driver loaded but no devices found
[4294708.686000] mice: PS/2 mouse device common for all mice
[4294708.746000] ieee1394: Initialized config rom entry `ip1394'
[4294708.756000] SCSI subsystem initialized
[4294708.766000] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
[4294708.844000] ndiswrapper version 1.1 loaded (preempt=no,smp=no)
[4294709.132000] ndiswrapper: driver bcmwl5 (Broadcom,12/22/2004, 3.100.46.0) loaded
[4294709.134000] ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 21
[4294709.150000] ndiswrapper: using irq 21
[4294709.662000] wlan0: ndiswrapper ethernet device 00:14:a4:61:bd:ae using driver bcmwl5, configuration file 14E4:4318:1468:0311.5.conf
[4294709.662000] wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
[4294709.692000] Linux agpgart interface v0.101 (c) Dave Jones
[4294709.710000] [fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
[4294709.710000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[4294709.710000] [fglrx] module loaded - fglrx 8.16.20 [Aug 16 2005] on minor 0
[4294709.996000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000
[4294710.002000] input: SynPS/2 Synaptics TouchPad on isa0060/serio4
[4294710.072000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[4294710.342000] ts: Compaq touchscreen protocol output
[4294715.356000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294716.962000] cdrom: open failed.
[4294722.110000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294722.142000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[4294723.036000] ACPI: PCI Interrupt 0000:00:14.5[b] -> GSI 17 (level, low) -> IRQ 17
[4294724.928000] Linux Kernel Card Services
[4294724.928000]   options:  [pci] [cardbus] [pm]
[4294724.950000] ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 20 (level, low) -> IRQ 20
[4294724.950000] Yenta: CardBus bridge found at 0000:06:06.0 [1025:0080]
[4294724.950000] Yenta: Using CSCINT to route CSC interrupts to PCI
[4294724.950000] Yenta: Routing CardBus interrupts to PCI
[4294724.950000] Yenta TI: socket 0000:06:06.0, mfunc 0x010a1b22, devctl 0x64
[4294725.172000] Yenta: ISA IRQ mask 0x0ef8, PCI irq 20
[4294725.172000] Socket status: 30000006
[4294725.356000] ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
[4294725.356000] ACPI: PCI Interrupt 0000:06:06.2[C] -> GSI 22 (level, low) -> IRQ 22
[4294725.464000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]  MMIO=[c0208000-c02087ff]  Max Packet=[2048]
[4294726.728000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[1234567812345678][4294727.248000] Real Time Clock Driver v1.12
[4294727.330000] input: PC Speaker
[4294731.622000] r8169: eth0: link up
[4294731.638000] NET: Registered protocol family 17
[4294733.664000] ACPI: AC Adapter [ADP1] (off-line)
[4294734.120000] ACPI: Battery Slot [BAT0] (battery present)
[4294734.152000] ACPI: Power Button (FF) [PWRF]
[4294734.152000] ACPI: Lid Switch [LID0]
[4294734.152000] ACPI: Sleep Button (CM) [SLPB]
[4294734.328000] ibm_acpi: ec object not found
[4294734.522000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[4294734.522000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[4294750.904000] [fglrx] free  PCIe = 51118080
[4294750.904000] [fglrx] max   PCIe = 51118080
[4294750.904000] [fglrx] free  LFB = 119762944
[4294750.904000] [fglrx] max   LFB = 119762944
[4294750.904000] [fglrx] free  Inv = 0
[4294750.904000] [fglrx] max   Inv = 0
[4294750.904000] [fglrx] total Inv = 0
[4294750.904000] [fglrx] total TIM = 0
[4294750.904000] [fglrx] total FB  = 0
[4294750.904000] [fglrx] total PCIe = 16384
[4294751.842000] apm: BIOS not found.
[4294753.368000] cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
[4294753.376000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
[4294753.376000] cs: IO port probe 0xa00-0xaff: clean.
[4294753.796000] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.40.4)
[4294753.796000] powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x4 (1450 mV)
[4294753.796000] powernow-k8:    1 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV)
[4294753.796000] powernow-k8:    2 : fid 0x0 (800 MHz), vid 0x16 (1000 mV)
[4294753.796000] cpu_init done, current fid 0xa, vid 0x4
[4294754.010000] Bluetooth: Core ver 2.7
[4294754.010000] NET: Registered protocol family 31
[4294754.010000] Bluetooth: HCI device and connection manager initialized
[4294754.010000] Bluetooth: HCI socket layer initialized
[4294754.034000] Bluetooth: L2CAP ver 2.7
[4294754.034000] Bluetooth: L2CAP socket layer initialized
[4294754.100000] Bluetooth: RFCOMM ver 1.5
[4294754.100000] Bluetooth: RFCOMM socket layer initialized
[4294754.100000] Bluetooth: RFCOMM TTY layer initialized
[4294759.332000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294772.534000] NET: Registered protocol family 10
[4294772.534000] Disabled Privacy Extensions on device c02eb280(lo)
[4294772.534000] IPv6 over IPv4 tunneling driver
[4294783.452000] eth0: no IPv6 routers present
[4294789.878000] APIC error on CPU0: 40(40)
[4294820.807000] psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
[4294830.633000] APIC error on CPU0: 40(40)
[4294857.928000] APIC error on CPU0: 40(40)
[4294954.003000] APIC error on CPU0: 40(40)
[4295154.998000] APIC error on CPU0: 40(40)
[4295190.589000] APIC error on CPU0: 40(40)

Je me demande si ce ne sont pas les dernières erreures.
PS: il n'est pas un peu long mon dmesg ?
merci

---

Ubuntu, c'est pas bien..................c'est génial :D

zeugme

Re : Problème lors du démarrage

alors la, aucune idee ...

cep_

Re : Problème lors du démarrage

Essaye pci=routeirq sur la ligne du kernel dans menu.lst de grub. Et vois aussi si nécessaire d'autres options comme irqpoll et/ou la série des lapic et compagnie.