#1 Le 24/01/2010, à 17:17
- baballe
Plus de clef ou disque dur en usb (netbook remix et eeepc)
Bonjour, j'ai un souci lié aux périfériques usb, ma souris fonctionne très bien (là je l'ai retirée pour l'instant) , aucun périférique n'apparait, c'est dommage car j'essaie de partionner un disque de 160 pour y faire une install
Je suis sur un eeepc 1000hd, avec ubuntu netbook remix 9.10
Par exemple, j'ai mis une clef Usb de 256mo, un disque en sub de 160g et une carte sd d'1go
dmesg me donne ça :
dmesg | tail -15
[ 1120.668542] scsi9 : SCSI emulation for USB Mass Storage devices
[ 1120.668779] usb-storage: device found at 5
[ 1120.668784] usb-storage: waiting for device to settle before scanning
[ 1125.669966] usb-storage: device scan complete
[ 1125.673517] scsi 9:0:0:0: Direct-Access Generic Flash Disk 7.77 PQ: 0 ANSI: 2
[ 1125.674342] sd 9:0:0:0: Attached scsi generic sg3 type 0
[ 1125.700933] sd 9:0:0:0: [sdd] 512000 512-byte logical blocks: (262 MB/250 MiB)
[ 1125.705934] sd 9:0:0:0: [sdd] Write Protect is off
[ 1125.705942] sd 9:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 1125.705948] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.722930] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.722943] sdd: sdd1
[ 1125.729979] sdd: p1 size 514048 exceeds device capacity, limited to end of disk
[ 1125.743970] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.743982] sd 9:0:0:0: [sdd] Attached SCSI removable disket lsusb :
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 009: ID 058f:6335 Alcor Micro Corp. SD/MMC Card Reader
Bus 001 Device 008: ID 067b:3507 Prolific Technology, Inc. PL3507 ATAPI6 Bridge
Bus 001 Device 002: ID 05e3:0505 Genesys Logic, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 005: ID 058f:9380 Alcor Micro Corp. Flash Drive
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hubEt pourtant aucun accès aux disques en question qui demeurent "invisibles"
Je patauge depuis ce matin sans trouver d'où ça peut venir, si quelqu'un pouvait me dire comment remédier à tout ça ... merci d'avance!
Ps , à tout ça j'ajoute un dsmeg (dsl pour la longueur hein et entre temps j'ai branché et débranché les disques pour voir si ça ne venait pas des ports) :
66085] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.166361] EISA: Probing bus 0 at eisa.0
[ 1.166401] EISA: Detected 0 cards.
[ 1.166586] cpuidle: using governor ladder
[ 1.166717] cpuidle: using governor menu
[ 1.167723] TCP cubic registered
[ 1.168093] NET: Registered protocol family 10
[ 1.169063] lo: Disabled Privacy Extensions
[ 1.169700] NET: Registered protocol family 17
[ 1.169741] Bluetooth: L2CAP ver 2.13
[ 1.169745] Bluetooth: L2CAP socket layer initialized
[ 1.169751] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.169756] Bluetooth: SCO socket layer initialized
[ 1.169826] Bluetooth: RFCOMM TTY layer initialized
[ 1.169832] Bluetooth: RFCOMM socket layer initialized
[ 1.169837] Bluetooth: RFCOMM ver 1.11
[ 1.169896] Using IPI No-Shortcut mode
[ 1.170050] PM: Resume from disk failed.
[ 1.170074] registered taskstats version 1
[ 1.170269] Magic number: 10:595:890
[ 1.170348] pci 0000:00:1f.3: hash matches
[ 1.170410] rtc_cmos 00:03: setting system clock to 2010-01-24 14:51:19 UTC (1264344679)
[ 1.170417] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.170421] EDD information not available.
[ 1.211984] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.264801] ata1.00: ATA-8: ST9160310AS, 0303, max UDMA/133
[ 1.264809] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.280580] ata1.00: configured for UDMA/133
[ 1.386274] ACPI: Battery Slot [BAT0] (battery present)
[ 1.386922] scsi 0:0:0:0: Direct-Access ATA ST9160310AS 0303 PQ: 0 ANSI: 5
[ 1.387190] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.387287] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.387387] sd 0:0:0:0: [sda] Write Protect is off
[ 1.387394] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.387447] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.387715] sda:
[ 1.436044] usb 1-8: new high speed USB device using ehci_hcd and address 2
[ 1.635839] sda1 sda2 sda3
[ 1.640029] Clocksource tsc unstable (delta = -391774831 ns)
[ 1.644646] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.644676] Freeing unused kernel memory: 540k freed
[ 1.645267] Write protecting the kernel text: 4568k
[ 1.645350] Write protecting the kernel read-only data: 1836k
[ 1.987009] usb 1-8: configuration #1 chosen from 1 choice
[ 1.997549] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:16/input/input6
[ 1.997629] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.070024] Linux agpgart interface v0.103
[ 2.147362] agpgart-intel 0000:00:00.0: Intel 915GM Chipset
[ 2.147698] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 2.151151] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 2.290681] [drm] Initialized drm 1.1.0 20060810
[ 2.321852] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.321865] i915 0000:00:02.0: setting latency timer to 64
[ 2.442819] ATL1E 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.442842] ATL1E 0000:03:00.0: setting latency timer to 64
[ 2.442896] integrated sync not supported
[ 2.726871] [drm] DAC-6: set mode 640x480 0
[ 2.909924] [drm:edid_is_valid] *ERROR* EDID checksum is invalid, remainder is 25
[ 2.909930] [drm:edid_is_valid] *ERROR* Raw EDID:
[ 2.909938] <3>00 ff ff ff ff ff ff 00 22 64 e9 03 23 47 02 00 ........"d..#G..
[ 2.909944] <3>0b 13 01 03 80 16 0d 78 0a 86 26 94 57 51 90 27 .......x..&.WQ.'
[ 2.909949] <3>21 4f 54 00 00 00 01 01 01 01 01 01 01 01 01 01 !OT.............
[ 2.909955] <3>01 01 01 01 01 01 94 11 00 b0 40 58 19 20 35 23 ..........@X. 5#
[ 2.909961] <3>45 00 dc 81 80 00 00 1f ff ff ff ff ff ff ff ff E...............
[ 2.909967] <3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
[ 2.909972] <3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
[ 2.909978] <3>ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
[ 2.909982]
[ 2.909988] i915 0000:00:02.0: LVDS-1: EDID invalid.
[ 2.951536] [drm] TV-14: set mode NTSC 480i 0
[ 3.078760] [drm] fb0: inteldrmfb frame buffer device
[ 3.078777] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 3.152400] render error detected, EIR: 0x00000010
[ 3.152406] page table error
[ 3.152409] PGTBL_ER: 0x00000100
[ 3.152415] [drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking
[ 3.152428] render error detected, EIR: 0x00000010
[ 3.152431] page table error
[ 3.152434] PGTBL_ER: 0x00000100
[ 3.162639] [drm] LVDS-8: set mode 1024x600 17
[ 3.200069] Console: switching to colour frame buffer device 128x37
[ 3.746339] xor: automatically using best checksumming function: pIII_sse
[ 3.764010] pIII_sse : 2332.000 MB/sec
[ 3.764015] xor: using function: pIII_sse (2332.000 MB/sec)
[ 3.771181] device-mapper: dm-raid45: initialized v0.2594b
[ 4.191686] PM: Starting manual resume from disk
[ 4.191697] PM: Resume from partition 8:2
[ 4.191701] PM: Checking hibernation image.
[ 4.192172] PM: Resume from disk failed.
[ 4.213789] EXT4-fs (sda1): barriers enabled
[ 4.230339] kjournald2 starting: pid 334, dev sda1:8, commit interval 5 seconds
[ 4.230367] EXT4-fs (sda1): delayed allocation enabled
[ 4.230374] EXT4-fs: file extents enabled
[ 4.232216] EXT4-fs: mballoc enabled
[ 4.232247] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 5.124322] type=1505 audit(1264344683.453:2): operation="profile_load" pid=357 name=/sbin/dhclient3
[ 5.125733] type=1505 audit(1264344683.453:3): operation="profile_load" pid=357 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 5.126501] type=1505 audit(1264344683.453:4): operation="profile_load" pid=357 name=/usr/lib/connman/scripts/dhclient-script
[ 5.185039] type=1505 audit(1264344683.513:5): operation="profile_load" pid=358 name=/usr/bin/evince
[ 5.207855] type=1505 audit(1264344683.533:6): operation="profile_load" pid=358 name=/usr/bin/evince-previewer
[ 5.221546] type=1505 audit(1264344683.549:7): operation="profile_load" pid=358 name=/usr/bin/evince-thumbnailer
[ 5.263359] type=1505 audit(1264344683.589:8): operation="profile_load" pid=360 name=/usr/lib/cups/backend/cups-pdf
[ 5.265062] type=1505 audit(1264344683.593:9): operation="profile_load" pid=360 name=/usr/sbin/cupsd
[ 13.465407] Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1 across:2000084k
[ 13.618511] udev: starting version 147
[ 13.715251] lp: driver loaded but no devices found
[ 13.716696] eeepc_laptop: Eee PC Hotkey Driver
[ 13.716838] eeepc_laptop: Hotkey init flags 0x41
[ 13.717035] eeepc_laptop: TYPE (2000000) not reported by BIOS, enabling anyway
[ 13.732534] eeepc_laptop: PANELPOWER (4000000) not reported by BIOS, enabling anyway
[ 13.732548] eeepc_laptop: Get control methods supported: 0x6101711
[ 13.732677] input: Asus EeePC extra buttons as /devices/virtual/input/input7
[ 14.033379] EXT4-fs (sda1): internal journal on sda1:8
[ 14.600803] intel_rng: FWH not detected
[ 14.641723] cfg80211: Calling CRDA to update world regulatory domain
[ 14.712409] cfg80211: World regulatory domain updated:
[ 14.712417] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.712424] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.712431] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.712437] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.712443] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.712449] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.751426] ath5k 0000:01:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 14.751443] ath5k 0000:01:00.0: setting latency timer to 64
[ 14.751512] ath5k 0000:01:00.0: registered as 'phy0'
[ 14.824787] Linux video capture interface: v2.00
[ 14.836274] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (05e3:0505)
[ 14.856585] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.974920] ath: EEPROM regdomain: 0x60
[ 14.974929] ath: EEPROM indicates we should expect a direct regpair map
[ 14.974937] ath: Country alpha2 being used: 00
[ 14.974941] ath: Regpair used: 0x60
[ 15.031815] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.031880] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 15.054609] usbcore: registered new interface driver uvcvideo
[ 15.054619] USB Video Class driver (v0.1.0)
[ 15.123596] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[ 15.271548] psmouse serio1: ID: 10 00 64
[ 15.432617] phy0: Selected rate control algorithm 'minstrel'
[ 15.434104] Registered led device: ath5k-phy0::rx
[ 15.434145] Registered led device: ath5k-phy0::tx
[ 15.434153] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 15.495147] elantech.c: assuming hardware version 2, firmware version 2.48
[ 15.581556] elantech.c: Synaptics capabilities query result 0x00, 0x02, 0x64.
[ 15.632076] EXT4-fs (sda3): barriers enabled
[ 15.669356] kjournald2 starting: pid 710, dev sda3:8, commit interval 5 seconds
[ 15.670077] EXT4-fs (sda3): internal journal on sda3:8
[ 15.670086] EXT4-fs (sda3): delayed allocation enabled
[ 15.670092] EXT4-fs: file extents enabled
[ 15.680750] EXT4-fs: mballoc enabled
[ 15.680787] EXT4-fs (sda3): mounted filesystem with ordered data mode
[ 15.818894] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input9
[ 16.143648] __ratelimit: 3 callbacks suppressed
[ 16.143657] type=1505 audit(1264344694.469:11): operation="profile_replace" pid=851 name=/sbin/dhclient3
[ 16.145230] type=1505 audit(1264344694.473:12): operation="profile_replace" pid=851 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 16.146012] type=1505 audit(1264344694.473:13): operation="profile_replace" pid=851 name=/usr/lib/connman/scripts/dhclient-script
[ 16.191974] type=1505 audit(1264344694.517:14): operation="profile_replace" pid=852 name=/usr/bin/evince
[ 16.257954] alloc irq_desc for 27 on node -1
[ 16.257962] alloc kstat_irqs on node -1
[ 16.257986] ATL1E 0000:03:00.0: irq 27 for MSI/MSI-X
[ 16.258527] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.424836] type=1505 audit(1264344694.753:15): operation="profile_replace" pid=852 name=/usr/bin/evince-previewer
[ 16.484558] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.501992] type=1505 audit(1264344694.829:16): operation="profile_replace" pid=852 name=/usr/bin/evince-thumbnailer
[ 16.620920] type=1505 audit(1264344694.949:17): operation="profile_replace" pid=905 name=/usr/lib/cups/backend/cups-pdf
[ 16.688451] type=1505 audit(1264344695.017:18): operation="profile_replace" pid=905 name=/usr/sbin/cupsd
[ 16.693760] type=1505 audit(1264344695.021:19): operation="profile_replace" pid=912 name=/usr/sbin/tcpdump
[ 17.619662] [drm] DAC-6: set mode 640x480 0
[ 18.074230] [drm] DAC-6: set mode 640x480 0
[ 18.475189] integrated sync not supported
[ 18.516976] [drm] TV-14: set mode NTSC 480i 0
[ 18.595969] ppdev: user-space parallel port driver
[ 18.737129] [drm] TV-14: set mode NTSC 480i 0
[ 18.886219] [drm] DAC-6: set mode 640x480 0
[ 18.992409] [drm] DAC-6: set mode 640x480 0
[ 19.244885] integrated sync not supported
[ 19.287985] [drm] TV-14: set mode NTSC 480i 0
[ 19.501046] [drm] TV-14: set mode NTSC 480i 0
[ 22.799354] [drm] DAC-6: set mode 640x480 0
[ 22.906311] [drm] DAC-6: set mode 640x480 0
[ 23.103517] integrated sync not supported
[ 23.146734] [drm] TV-14: set mode NTSC 480i 0
[ 23.289576] [drm] TV-14: set mode NTSC 480i 0
[ 23.446689] [drm] DAC-6: set mode 640x480 0
[ 23.554379] [drm] DAC-6: set mode 640x480 0
[ 23.718611] integrated sync not supported
[ 23.761784] [drm] TV-14: set mode NTSC 480i 0
[ 23.903337] [drm] TV-14: set mode NTSC 480i 0
[ 24.054855] [drm] DAC-6: set mode 640x480 0
[ 24.161708] [drm] DAC-6: set mode 640x480 0
[ 24.325890] integrated sync not supported
[ 24.369080] [drm] TV-14: set mode NTSC 480i 0
[ 24.511282] [drm] TV-14: set mode NTSC 480i 0
[ 178.975923] [drm] DAC-6: set mode 640x480 0
[ 179.149058] [drm] DAC-6: set mode 640x480 0
[ 179.341064] integrated sync not supported
[ 179.384301] [drm] TV-14: set mode NTSC 480i 0
[ 179.526826] [drm] TV-14: set mode NTSC 480i 0
[ 179.679047] [drm] DAC-6: set mode 640x480 0
[ 179.787578] [drm] DAC-6: set mode 640x480 0
[ 179.950250] integrated sync not supported
[ 179.993414] [drm] TV-14: set mode NTSC 480i 0
[ 180.134644] [drm] TV-14: set mode NTSC 480i 0
[ 180.303577] [drm] DAC-6: set mode 640x480 0
[ 180.425018] [drm] DAC-6: set mode 640x480 0
[ 180.588957] integrated sync not supported
[ 180.632152] [drm] TV-14: set mode NTSC 480i 0
[ 180.794884] [drm] TV-14: set mode NTSC 480i 0
[ 184.659166] [drm] DAC-6: set mode 640x480 0
[ 184.779023] [drm] DAC-6: set mode 640x480 0
[ 184.941391] integrated sync not supported
[ 184.984493] [drm] TV-14: set mode NTSC 480i 0
[ 185.125640] [drm] TV-14: set mode NTSC 480i 0
[ 193.423977] wlan0: authenticate with AP 00:18:4d:19:1f:42
[ 193.429263] wlan0: authenticated
[ 193.429273] wlan0: associate with AP 00:18:4d:19:1f:42
[ 193.431725] wlan0: RX AssocResp from 00:18:4d:19:1f:42 (capab=0x431 status=0 aid=1)
[ 193.431735] wlan0: associated
[ 193.437256] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 203.872019] wlan0: no IPv6 routers present
[ 257.340085] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 257.559679] usb 3-1: configuration #1 chosen from 1 choice
[ 257.683810] Initializing USB Mass Storage driver...
[ 257.686221] scsi2 : SCSI emulation for USB Mass Storage devices
[ 257.686577] usbcore: registered new interface driver usb-storage
[ 257.686586] USB Mass Storage support registered.
[ 257.687843] usb-storage: device found at 2
[ 257.687849] usb-storage: waiting for device to settle before scanning
[ 262.686135] usb-storage: device scan complete
[ 262.689139] scsi 2:0:0:0: Direct-Access Generic Flash Disk 7.77 PQ: 0 ANSI: 2
[ 262.690340] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 262.713095] sd 2:0:0:0: [sdb] 512000 512-byte logical blocks: (262 MB/250 MiB)
[ 262.718096] sd 2:0:0:0: [sdb] Write Protect is off
[ 262.718104] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 262.718110] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 262.736102] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 262.736114] sdb: sdb1
[ 262.743142] sdb: p1 size 514048 exceeds device capacity, limited to end of disk
[ 262.757138] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 262.757151] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 360.016184] usb 3-1: USB disconnect, address 2
[ 366.104154] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 366.275461] usb 3-2: configuration #1 chosen from 1 choice
[ 366.278527] scsi3 : SCSI emulation for USB Mass Storage devices
[ 366.278758] usb-storage: device found at 3
[ 366.278763] usb-storage: waiting for device to settle before scanning
[ 371.277863] usb-storage: device scan complete
[ 371.280879] scsi 3:0:0:0: Direct-Access M-Sys DiskOnKey 4.31 PQ: 0 ANSI: 0 CCS
[ 371.282173] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 371.310832] sd 3:0:0:0: [sdb] 497664 512-byte logical blocks: (254 MB/243 MiB)
[ 371.313835] sd 3:0:0:0: [sdb] Write Protect is off
[ 371.313843] sd 3:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 371.313849] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 371.325832] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 371.325845] sdb: sdb1
[ 371.350851] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 371.350862] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 516.008207] usb 3-2: USB disconnect, address 3
[ 540.392092] usb 3-2: new full speed USB device using uhci_hcd and address 4
[ 540.561446] usb 3-2: configuration #1 chosen from 1 choice
[ 540.568202] scsi4 : SCSI emulation for USB Mass Storage devices
[ 540.568437] usb-storage: device found at 4
[ 540.568442] usb-storage: waiting for device to settle before scanning
[ 545.569853] usb-storage: device scan complete
[ 545.572867] scsi 4:0:0:0: Direct-Access M-Sys DiskOnKey 4.31 PQ: 0 ANSI: 0 CCS
[ 545.574067] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 545.602820] sd 4:0:0:0: [sdb] 497664 512-byte logical blocks: (254 MB/243 MiB)
[ 545.605819] sd 4:0:0:0: [sdb] Write Protect is off
[ 545.605827] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 545.605833] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 545.617813] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 545.617826] sdb: sdb1
[ 545.645858] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 545.645870] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 585.696208] usb 3-2: USB disconnect, address 4
[ 591.996160] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 592.129676] usb 1-5: configuration #1 chosen from 1 choice
[ 592.132557] scsi5 : SCSI emulation for USB Mass Storage devices
[ 592.132793] usb-storage: device found at 6
[ 592.132797] usb-storage: waiting for device to settle before scanning
[ 597.132308] usb-storage: device scan complete
[ 597.132921] scsi 5:0:0:0: Direct-Access Single Flash Reader 1.00 PQ: 0 ANSI: 0
[ 597.133832] sd 5:0:0:0: Attached scsi generic sg1 type 0
[ 597.631138] sd 5:0:0:0: [sdb] 1984000 512-byte logical blocks: (1.01 GB/968 MiB)
[ 597.631869] sd 5:0:0:0: [sdb] Write Protect is off
[ 597.631875] sd 5:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 597.631881] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 597.637121] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 597.637133] sdb: sdb1
[ 597.651270] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 597.651282] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 773.338661] usb 1-5: USB disconnect, address 6
[ 773.345504] FAT: bread failed in fat_clusters_flush
[ 773.392995] FAT: bread failed in fat_clusters_flush
[ 773.407738] FAT: bread failed in fat_clusters_flush
[ 773.407809] FAT: bread failed in fat_clusters_flush
[ 778.612120] usb 1-5: new high speed USB device using ehci_hcd and address 7
[ 778.745703] usb 1-5: configuration #1 chosen from 1 choice
[ 778.748556] scsi6 : SCSI emulation for USB Mass Storage devices
[ 778.748784] usb-storage: device found at 7
[ 778.748789] usb-storage: waiting for device to settle before scanning
[ 783.748220] usb-storage: device scan complete
[ 783.748835] scsi 6:0:0:0: Direct-Access Single Flash Reader 1.00 PQ: 0 ANSI: 0
[ 783.749741] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 784.252175] sd 6:0:0:0: [sdb] 1984000 512-byte logical blocks: (1.01 GB/968 MiB)
[ 784.252911] sd 6:0:0:0: [sdb] Write Protect is off
[ 784.252917] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 784.252923] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 784.257804] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 784.257818] sdb: sdb1
[ 784.271558] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 784.271570] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 863.864115] usb 1-2: new high speed USB device using ehci_hcd and address 8
[ 863.998565] usb 1-2: configuration #1 chosen from 1 choice
[ 864.000560] scsi7 : SCSI emulation for USB Mass Storage devices
[ 864.000800] usb-storage: device found at 8
[ 864.000805] usb-storage: waiting for device to settle before scanning
[ 869.000476] usb-storage: device scan complete
[ 869.001320] scsi 7:0:0:0: Direct-Access WDC WD16 00JB-00EVA0 15.0 PQ: 0 ANSI: 0
[ 869.002382] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 869.023447] sd 7:0:0:0: [sdc] Adjusting the sector count from its reported value: 312581808
[ 869.023462] sd 7:0:0:0: [sdc] 312581807 512-byte logical blocks: (160 GB/149 GiB)
[ 869.025069] sd 7:0:0:0: [sdc] Write Protect is off
[ 869.025077] sd 7:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 869.025083] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 869.026037] sd 7:0:0:0: [sdc] Adjusting the sector count from its reported value: 312581808
[ 869.026908] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 869.026917] sdc: sdc1
[ 869.061386] sd 7:0:0:0: [sdc] Adjusting the sector count from its reported value: 312581808
[ 869.062832] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 869.062843] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 1108.148065] usb 1-5: USB disconnect, address 7
[ 1108.154911] FAT: bread failed in fat_clusters_flush
[ 1108.164863] FAT: bread failed in fat_clusters_flush
[ 1108.212234] FAT: bread failed in fat_clusters_flush
[ 1108.212311] FAT: bread failed in fat_clusters_flush
[ 1113.112117] usb 1-5: new high speed USB device using ehci_hcd and address 9
[ 1113.246178] usb 1-5: configuration #1 chosen from 1 choice
[ 1113.248560] scsi8 : SCSI emulation for USB Mass Storage devices
[ 1113.248800] usb-storage: device found at 9
[ 1113.248805] usb-storage: waiting for device to settle before scanning
[ 1118.248307] usb-storage: device scan complete
[ 1118.248918] scsi 8:0:0:0: Direct-Access Single Flash Reader 1.00 PQ: 0 ANSI: 0
[ 1118.249828] sd 8:0:0:0: Attached scsi generic sg1 type 0
[ 1118.748758] sd 8:0:0:0: [sdb] 1984000 512-byte logical blocks: (1.01 GB/968 MiB)
[ 1118.749493] sd 8:0:0:0: [sdb] Write Protect is off
[ 1118.749500] sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1118.749506] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 1118.755001] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 1118.755015] sdb: sdb1
[ 1118.767533] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[ 1118.767546] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 1120.488098] usb 3-2: new full speed USB device using uhci_hcd and address 5
[ 1120.664581] usb 3-2: configuration #1 chosen from 1 choice
[ 1120.668542] scsi9 : SCSI emulation for USB Mass Storage devices
[ 1120.668779] usb-storage: device found at 5
[ 1120.668784] usb-storage: waiting for device to settle before scanning
[ 1125.669966] usb-storage: device scan complete
[ 1125.673517] scsi 9:0:0:0: Direct-Access Generic Flash Disk 7.77 PQ: 0 ANSI: 2
[ 1125.674342] sd 9:0:0:0: Attached scsi generic sg3 type 0
[ 1125.700933] sd 9:0:0:0: [sdd] 512000 512-byte logical blocks: (262 MB/250 MiB)
[ 1125.705934] sd 9:0:0:0: [sdd] Write Protect is off
[ 1125.705942] sd 9:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 1125.705948] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.722930] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.722943] sdd: sdd1
[ 1125.729979] sdd: p1 size 514048 exceeds device capacity, limited to end of disk
[ 1125.743970] sd 9:0:0:0: [sdd] Assuming drive cache: write through
[ 1125.743982] sd 9:0:0:0: [sdd] Attached SCSI removable disk
[ 1614.896110] usb 3-2: USB disconnect, address 5
[ 1617.129986] usb 1-5: USB disconnect, address 9
[ 1617.134628] FAT: bread failed in fat_clusters_flush
[ 1617.142488] FAT: bread failed in fat_clusters_flush
[ 1617.187050] FAT: bread failed in fat_clusters_flush
[ 1617.187127] FAT: bread failed in fat_clusters_flush
[ 1617.648090] usb 1-2: USB disconnect, address 8
[ 1617.654852] FAT: bread failed in fat_clusters_flush
[ 1617.662335] FAT: bread failed in fat_clusters_flush
[ 1617.701332] FAT: bread failed in fat_clusters_flush
[ 1617.701408] FAT: bread failed in fat_clusters_flush
[ 1624.420168] usb 1-3: new high speed USB device using ehci_hcd and address 11
[ 1624.554563] usb 1-3: configuration #1 chosen from 1 choice
[ 1624.557629] scsi10 : SCSI emulation for USB Mass Storage devices
[ 1624.557859] usb-storage: device found at 11
[ 1624.557864] usb-storage: waiting for device to settle before scanning
[ 1628.727072] usb 1-3: USB disconnect, address 11
[ 1646.856129] usb 1-3: new high speed USB device using ehci_hcd and address 12
[ 1646.990560] usb 1-3: configuration #1 chosen from 1 choice
[ 1646.993642] scsi11 : SCSI emulation for USB Mass Storage devices
[ 1646.993876] usb-storage: device found at 12
[ 1646.993880] usb-storage: waiting for device to settle before scanning
[ 1651.992448] usb-storage: device scan complete
[ 1651.993192] scsi 11:0:0:0: Direct-Access WDC WD16 00JB-00EVA0 15.0 PQ: 0 ANSI: 0
[ 1651.994104] sd 11:0:0:0: Attached scsi generic sg1 type 0
[ 1652.014386] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 312581808
[ 1652.014400] sd 11:0:0:0: [sdb] 312581807 512-byte logical blocks: (160 GB/149 GiB)
[ 1652.016062] sd 11:0:0:0: [sdb] Write Protect is off
[ 1652.016072] sd 11:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1652.016078] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[ 1652.018351] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 312581808
[ 1652.019271] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[ 1652.019282] sdb: sdb1
[ 1652.048226] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 312581808
[ 1652.049545] sd 11:0:0:0: [sdb] Assuming drive cache: write through
[ 1652.049556] sd 11:0:0:0: [sdb] Attached SCSI disk
[ 1698.916052] usb 1-5: new high speed USB device using ehci_hcd and address 13
[ 1699.049697] usb 1-5: configuration #1 chosen from 1 choice
[ 1699.052561] scsi12 : SCSI emulation for USB Mass Storage devices
[ 1699.052792] usb-storage: device found at 13
[ 1699.052797] usb-storage: waiting for device to settle before scanning
[ 1703.004212] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 1703.179351] usb 2-2: configuration #1 chosen from 1 choice
[ 1703.182345] scsi13 : SCSI emulation for USB Mass Storage devices
[ 1703.182598] usb-storage: device found at 2
[ 1703.182603] usb-storage: waiting for device to settle before scanning
[ 1704.052214] usb-storage: device scan complete
[ 1704.052823] scsi 12:0:0:0: Direct-Access Single Flash Reader 1.00 PQ: 0 ANSI: 0
[ 1704.053627] sd 12:0:0:0: Attached scsi generic sg2 type 0
[ 1704.554163] sd 12:0:0:0: [sdc] 1984000 512-byte logical blocks: (1.01 GB/968 MiB)
[ 1704.554894] sd 12:0:0:0: [sdc] Write Protect is off
[ 1704.554901] sd 12:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 1704.554906] sd 12:0:0:0: [sdc] Assuming drive cache: write through
[ 1704.560170] sd 12:0:0:0: [sdc] Assuming drive cache: write through
[ 1704.560184] sdc: sdc1
[ 1704.572557] sd 12:0:0:0: [sdc] Assuming drive cache: write through
[ 1704.572571] sd 12:0:0:0: [sdc] Attached SCSI removable disk
[ 1708.181194] usb-storage: device scan complete
[ 1708.184280] scsi 13:0:0:0: Direct-Access Generic Flash Disk 7.77 PQ: 0 ANSI: 2
[ 1708.185069] sd 13:0:0:0: Attached scsi generic sg3 type 0
[ 1708.201657] sd 13:0:0:0: [sdd] 512000 512-byte logical blocks: (262 MB/250 MiB)
[ 1708.207179] sd 13:0:0:0: [sdd] Write Protect is off
[ 1708.207189] sd 13:0:0:0: [sdd] Mode Sense: 03 00 00 00
[ 1708.207195] sd 13:0:0:0: [sdd] Assuming drive cache: write through
[ 1708.224157] sd 13:0:0:0: [sdd] Assuming drive cache: write through
[ 1708.224171] sdd: sdd1
[ 1708.231182] sdd: p1 size 514048 exceeds device capacity, limited to end of disk
[ 1708.258145] sd 13:0:0:0: [sdd] Assuming drive cache: write through
[ 1708.258157] sd 13:0:0:0: [sdd] Attached SCSI removable disk
vincent@vincent:~$Dernière modification par baballe (Le 24/01/2010, à 17:25)
Hors ligne