#1 Le 01/03/2010, à 22:59
- jeanmaire
température des CPU - résolu grace à pascal34 et PatrickZorblug
Bonsoir
J'ai installé lm-sensors pour contrôler la température des CPU de ma config
sudo apt get install lm-sensors --> OK!
sudo sensors detect --> OK
Envoyé l'applet controle Hardware sur untableau de bord !
Et je n'obtiens que la température du GPU de la carte graphique
J'ai loupé quoi ?
Merci
Georges
____________________________
CPU : I7 720 overclocké à 3.6 Ghrz
MEM : 6 Giga CORSAIR 1600 Dominator
CM : ASUS P6TD Deluxe
Ventirad : Coolermaster V8
CG : Gainward GT240 512MO
DD : 2 x WD 500 Giga 32 MO cache
Boitier : CoolerMaster Storm Snipper
Alim : Cooler Master 520 Watts
Windows 7 64 bits – Ubuntu Karmic 64 bits – Vegas 9.0c 64 bits
Dernière modification par jeanmaire (Le 15/03/2010, à 10:16)
Hors ligne
#2 Le 01/03/2010, à 23:01
- JB-home
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
qu'es que tu obtiens en tapant "sudo sensors" dans le terminal ?
Hors ligne
#3 Le 01/03/2010, à 23:24
- jeanmaire
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
voili , voilà ...
jojo@jojo-desktop:~$ sudo sensors
[sudo] password for jojo:
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
jojo@jojo-desktop:~$
Alors je continue --->:
jojo@jojo-desktop:~$ sudo sensors detect
Parse error in chip name `detect'
Try `sensors -h' for more information
jojo@jojo-desktop:~$ sudo sensors -h
Usage: sensors [OPTION]... [CHIP]...
-c, --config-file Specify a config file
-h, --help Display this help text
-s, --set Execute `set' statements (root only)
-f, --fahrenheit Show temperatures in degrees fahrenheit
-A, --no-adapter Do not show adapter for each chip
--bus-list Generate bus statements for sensors.conf
-u Raw output (debugging only)
-v, --version Display the program version
Use `-' after `-c' to read the config file from stdin.
If no chips are specified, all chip info will be printed.
Example chip names:
lm78-i2c-0-2d *-i2c-0-2d
lm78-i2c-0-* *-i2c-0-*
lm78-i2c-*-2d *-i2c-*-2d
lm78-i2c-*-* *-i2c-*-*
lm78-isa-0290 *-isa-0290
lm78-isa-* *-isa-*
lm78-*
jojo@jojo-desktop:~$
Si ça peut t'aider
Amicalement
Georges
Hors ligne
#4 Le 01/03/2010, à 23:27
- JB-home
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
bon déjà c'est normal, il faut que tu tape :
sudo sensors-detect
ça fonctionnera mieux après..
Hors ligne
#5 Le 02/03/2010, à 00:34
- jeanmaire
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Je l'avais fait et répondu "yes " à toutes les questions . Je viens de recommencer
jojo@jojo-desktop:~$ sudo sensors-detect
[sudo] password for jojo:
# sensors-detect revision 5249 (2008-05-11 22:56:25 +0200)
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): yes
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel ICH10
We will now try to load each adapter module in turn.
Module `i2c-i801' already loaded.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.
We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.
Next adapter: NVIDIA i2c adapter (i2c-0)
Do you want to scan it? (YES/no/selectively): yes
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Client found at address 0x51
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Client found at address 0x53
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... No
Probing for `EDID EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Next adapter: NVIDIA i2c adapter (i2c-1)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-2)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-3)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-4)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-5)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-6)
Do you want to scan it? (YES/no/selectively): yes
Next adapter: NVIDIA i2c adapter (i2c-7)
Do you want to scan it? (YES/no/selectively): yes
Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): yes
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Fintek'... Yes
Found unknown chip with ID 0xa513
(logical device B has address 0x290, could be sensors)
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Fintek'... No
Trying family `ITE'... No
Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): yes
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See
http://www.lm-sensors.org/wiki/FAQ/Chapter3 for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.
jojo@jojo-desktop:~$
J'ai regardé le site mentionné pour retrouver mon chip je sais que c'est un INTEL X58 / ICH10 R (carte mère ASUS P6TD DeLuxe) . Je ne l'ai pas trouvé ! ---> Apparement pas supporté par cette version de lm-sensors :
sensors-detect revision 5249 (2008-05-11 22:56:25 +0200) ( voir en tête de listing )
Et alors ? Existe-t-il une version plus récente ou un autre programme de contrôle de la température du CPU ?
La machine étant overclockée , j'ai absolument besoin de vérifier les températures CPU lorsqu'elle est chargée au max .
Merci
Georges
Dernière modification par jeanmaire (Le 02/03/2010, à 10:52)
Hors ligne
#6 Le 05/03/2010, à 12:03
- jeanmaire
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Bonjour
Je relance !
Comment connaitre la température des CPU sous UBUNTU ???
Merci
Georges
Hors ligne
#7 Le 10/03/2010, à 14:48
- HacKurx
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Salut, la seule façon à ma connaissance c'est lm-sensors mais il doit y avoir un problème au niveau d'un chip de la carte mère (peut être trop récente?).
Essaye la dernière version:
http://www.lm-sensors.org/wiki/Download
Follow Me: http://hackurx.wordpress.com
Hors ligne
#8 Le 10/03/2010, à 14:50
- HacKurx
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Waa pas mal ton boitier "CoolerMaster Storm Snipper"
Follow Me: http://hackurx.wordpress.com
Hors ligne
#9 Le 10/03/2010, à 15:40
- jeanmaire
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
@ubuntosaure
Oui , bon boitier ! J'avais eu l'info par ailleurs ; mais étant nouveau sur UBUNTU , j'hésite à me lancer dans des installs sans le script complet .
Merci
Georges
Hors ligne
#10 Le 10/03/2010, à 18:14
- HacKurx
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Ok, mais si tu le compile, il te suffit de suivre le fichier "install" du fichier pour installer les dépendance surtout bison et flex.
Je n'ai pas trouvé de dépôt pour obtenir la dernière version en paquet debian.
Il te faudra donc attendre ubuntu 10.04 ou te contenter d'un acpi -V.
Follow Me: http://hackurx.wordpress.com
Hors ligne
#11 Le 11/03/2010, à 19:07
- Seb_12
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Salut
J'avai aussi des problème avec lm-sensors, et en suivant les instructions spécifique à la 9.10 (http://doc.ubuntu-fr.org/lm-sensors), maintenant quand je fait sensors j'obtient
atk0110-acpi-0
Adapter: ACPI interface
+3.3 Voltage: +3.42 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.14 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +12.25 V (min = +10.20 V, max = +13.80 V)
DRAM Voltage: +1.55 V (min = +1.40 V, max = +1.90 V)
CPU Vcore Voltage: +0.85 V (min = +0.80 V, max = +2.50 V)
CPU PLL Voltage: +1.80 V (min = +1.20 V, max = +3.01 V)
VTT CPU Voltage: +1.12 V (min = +0.80 V, max = +2.00 V)
DRAM Voltage: +1.06 V (min = +1.00 V, max = +1.30 V)
DRAM Voltage: +1.53 V (min = +1.80 V, max = +3.40 V)
DRAM Voltage: +1.80 V (min = +1.80 V, max = +3.40 V)
DRAM Termination Voltage: +0.77 V (min = +0.60 V, max = +1.30 V)
CPU FAN Speed: 898 RPM (min = 600 RPM)
CHA_FAN1 Speed: 0 RPM (min = 600 RPM)
CHA_FAN2 Speed: 900 RPM (min = 600 RPM)
OPT_FAN1 Speed: 0 RPM (min = 600 RPM)
OPT_FAN2 Speed: 0 RPM (min = 600 RPM)
CPU Temperature: +44.0°C (high = +60.0°C, crit = +65.0°C)
MB Temperature: +37.0°C (high = +45.0°C, crit = +55.0°C)
PCH Temperature: +41.0°C (high = +65.0°C, crit = +95.0°C)
POWER Temperature: +24.0°C (high = +55.0°C, crit = +95.0°C)
OPT_TEMP1 Temperature: +0.0°C (high = +45.0°C, crit = +45.0°C)
OPT_TEMP2 Temperature: +0.0°C (high = +45.0°C, crit = +45.0°C)
Même si a la fin de sensors-detect il me dit qu'il n'y a pas de module a installer.
Par contre je n'arrive pas encore a avoir les température dans l'applet de KDE...
Maximus III / i5 750 / 4Go - 1866Mhz / Noctua DH14 / Vertex 2 / OC station / 9600GT
Hors ligne
#12 Le 20/03/2010, à 16:13
- HacKurx
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Sinon répond par "yes" à cette commande et copie ici tout ce qui est écrit:
sudo sensors-detect
Follow Me: http://hackurx.wordpress.com
Hors ligne
#13 Le 20/03/2010, à 16:14
- HacKurx
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Tu auras peut être une phrase du genre:
Warning: the required module ... is not currently installed
on your system. If it is built into the kernel then it's OK.
Otherwise, check http://www.lm-sensors.org/wiki/Devices for
driver availability.
Follow Me: http://hackurx.wordpress.com
Hors ligne
#14 Le 25/03/2010, à 20:44
- jeanmaire
Re : température des CPU - résolu grace à pascal34 et PatrickZorblug
Toutes mes excuses à tous . J'étais absent pour quelques jours , mais avant de partir , j'ai réussi à installer correctement lm-sensors sans vous en avertir autrement qu'en disant que le pb. était résolu grace à PatrckZorblug et Pascal 34
Bonne soirée
Georges
Hors ligne