webcam sur paviliondv9605

gayon · Le 02/01/2011, à 17:55

bonjour,

je rencontre un soucis avec ma webcam sur mon hp avec maverick 64bits:
à l'installation la webcam fonctionnait,mais apres mise à jour,je ne la vois plus:

moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

j'ai cru comprendre en parcourant le forum que c'était galère

une idée?

Stemp · Le 02/01/2011, à 20:57

Salut, selon lsusb il n'y a pas de webcam branchée.
Il y a peut-être une option dans le bios ou autre ?

gayon · Le 02/01/2011, à 21:22

le bios est on ne peut plus simple:ordre de démarrage et 2 3 bricoles mais rien sur les périphériques

et la webcam est inclus dans un pc portable

j'ai trouvé ca:

moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ gstreamer-properties
gstreamer-properties-Message: Skipping unavailable plugin 'artsdsink'
gstreamer-properties-Message: Skipping unavailable plugin 'esdsink'
gstreamer-properties-Message: Skipping unavailable plugin 'sunaudiosink'
gstreamer-properties-Message: Skipping unavailable plugin 'glimagesink'
gstreamer-properties-Message: Skipping unavailable plugin 'sdlvideosink'
gstreamer-properties-Message: Skipping unavailable plugin 'v4lmjpegsrc'
gstreamer-properties-Message: Skipping unavailable plugin 'qcamsrc'
gstreamer-properties-Message: Skipping unavailable plugin 'esdmon'
gstreamer-properties-Message: Skipping unavailable plugin 'sunaudiosrc'
gstreamer-properties-Message: Error running pipeline 'Video for Linux 2 (v4l2)': Impossible d'identifier le périphérique « /dev/video0 ». [v4l2_calls.c(488): gst_v4l2_open (): /GstPipeline:pipeline1/GstV4l2Src:v4l2src1:
system error: Aucun fichier ou dossier de ce type]

Dernière modification par gayon (Le 02/01/2011, à 21:56)

Stemp · Le 03/01/2011, à 00:10

Regarde bien le résultat de la commande lsusb : Il n'y a pas de webcam connectée !
Ce n'est donc pas la peine de regarder vers les drivers ou gstreamer, puisque le périphérique n'est même pas détecté.

Puisque tu indiques que la webcam fonctionnait avant une mise à jour, je présume que tu as un bug avec tes ports usb.
Essaye de regarder les messages dans dmesg qui pourraient indiquer un soucis.

gayon · Le 03/01/2011, à 00:15

[ 0.551948] ACPI: Power Button [PWRF]
[ 0.552363] ACPI: acpi_idle registered with cpuidle
[ 0.552429] ACPI: processor limited to max C-state 1
[ 0.556673] [Firmware Bug]: Invalid critical threshold (0)
[ 0.557373] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.557387] ACPI: Thermal Zone [THRM] (39 C)
[ 0.557500] ERST: Table is not found!
[ 0.557921] Linux agpgart interface v0.103
[ 0.557927] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.559772] brd: module loaded
[ 0.560523] loop: module loaded
[ 0.561314] ACPI: Battery Slot [BAT0] (battery absent)
[ 0.570284] pata_acpi 0000:00:06.0: setting latency timer to 64
[ 0.570840] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23
[ 0.570846] alloc irq_desc for 23 on node 0
[ 0.570849] alloc kstat_irqs on node 0
[ 0.570862] pata_acpi 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23
[ 0.570889] pata_acpi 0000:00:09.0: setting latency timer to 64
[ 0.570899] pata_acpi 0000:00:09.0: PCI INT A disabled
[ 0.573036] Fixed MDIO Bus: probed
[ 0.573083] PPP generic driver version 2.4.2
[ 0.573156] tun: Universal TUN/TAP device driver, 1.6
[ 0.573158] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.573290] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.580617] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
[ 0.580625] alloc irq_desc for 22 on node 0
[ 0.580628] alloc kstat_irqs on node 0
[ 0.580641] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 22 (level, low) -> IRQ 22
[ 0.580668] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 0.580672] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 0.580782] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 0.580816] ehci_hcd 0000:00:02.1: debug port 1
[ 0.580825] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 0.580853] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf6489000
[ 0.600089] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 0.600288] hub 1-0:1.0: USB hub found
[ 0.600295] hub 1-0:1.0: 7 ports detected
[ 0.610636] ACPI: PCI Interrupt Link [Z019] enabled at IRQ 22
[ 0.610645] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z019] -> GSI 22 (level, low) -> IRQ 22
[ 0.610672] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 0.610676] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 0.610772] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[ 0.610810] ehci_hcd 0000:00:04.1: debug port 1
[ 0.610818] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 0.610829] ehci_hcd 0000:00:04.1: irq 22, io mem 0xf6489400
[ 0.630174] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 0.630378] hub 2-0:1.0: USB hub found
[ 0.630385] hub 2-0:1.0: 2 ports detected
[ 0.630498] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.640581] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18
[ 0.640588] alloc irq_desc for 18 on node 0
[ 0.640591] alloc kstat_irqs on node 0
[ 0.640604] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 18 (level, low) -> IRQ 18
[ 0.640633] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.640636] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.640733] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 0.640774] ohci_hcd 0000:00:02.0: irq 18, io mem 0xf6486000
[ 0.653062] Freeing initrd memory: 10740k freed
[ 0.702287] hub 3-0:1.0: USB hub found
[ 0.702296] hub 3-0:1.0: 7 ports detected
[ 0.702882] ACPI: PCI Interrupt Link [Z018] enabled at IRQ 18
[ 0.702889] ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z018] -> GSI 18 (level, low) -> IRQ 18
[ 0.702913] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 0.702917] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 0.702993] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
[ 0.703015] ohci_hcd 0000:00:04.0: irq 18, io mem 0xf6487000
[ 0.762176] hub 4-0:1.0: USB hub found
[ 0.762183] hub 4-0:1.0: 2 ports detected
[ 0.762289] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.762446] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 0.784090] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.784099] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.784216] mice: PS/2 mouse device common for all mice
[ 0.784417] rtc_cmos 00:07: RTC can wake from S4
[ 0.784476] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 0.784519] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 0.784656] device-mapper: uevent: version 1.0.3
[ 0.784781] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 0.784875] device-mapper: multipath: version 1.1.1 loaded
[ 0.784879] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.785082] cpuidle: using governor ladder
[ 0.785085] cpuidle: using governor menu
[ 0.785468] TCP cubic registered
[ 0.785646] NET: Registered protocol family 10
[ 0.786222] lo: Disabled Privacy Extensions
[ 0.786558] NET: Registered protocol family 17
[ 0.786607] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 (2 cpu cores) (version 2.20.00)
[ 0.786665] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x13
[ 0.786668] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
[ 0.786670] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
[ 0.786891] PM: Resume from disk failed.
[ 0.786906] registered taskstats version 1
[ 0.787235] Magic number: 11:134:853
[ 0.787368] rtc_cmos 00:07: setting system clock to 2011-01-02 21:48:01 UTC (1294004881)
[ 0.787372] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.787374] EDD information not available.
[ 0.787484] Freeing unused kernel memory: 908k freed
[ 0.788109] Write protecting the kernel read-only data: 10240k
[ 0.788315] Freeing unused kernel memory: 412k freed
[ 0.788783] Freeing unused kernel memory: 1644k freed
[ 0.804151] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 0.818554] udev[111]: starting version 163
[ 1.005411] pata_amd 0000:00:06.0: version 0.4.1
[ 1.005469] pata_amd 0000:00:06.0: setting latency timer to 64
[ 1.012805] sdhci: Secure Digital Host Controller Interface driver
[ 1.012810] sdhci: Copyright(c) Pierre Ossman
[ 1.014787] scsi0 : pata_amd
[ 1.025437] ACPI: PCI Interrupt Link [LK4E] enabled at IRQ 19
[ 1.025446] alloc irq_desc for 19 on node 0
[ 1.025449] alloc kstat_irqs on node 0
[ 1.025464] b43-pci-bridge 0000:03:00.0: PCI INT A -> Link[LK4E] -> GSI 19 (level, low) -> IRQ 19
[ 1.025478] b43-pci-bridge 0000:03:00.0: setting latency timer to 64
[ 1.051243] scsi1 : pata_amd
[ 1.051827] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
[ 1.051831] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
[ 1.054376] sdhci-pci 0000:02:05.1: SDHCI controller found [1180:0822] (rev 22)
[ 1.054837] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
[ 1.054853] sdhci-pci 0000:02:05.1: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7
[ 1.055906] sdhci-pci 0000:02:05.1: Will use DMA mode even though HW doesn't fully claim to support it.
[ 1.056977] Registered led device: mmc0::
[ 1.060144] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x13, vendor 0x4243)
[ 1.060153] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
[ 1.060160] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[ 1.060166] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x05, vendor 0x4243)
[ 1.067401] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1.067879] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 1.067886] alloc irq_desc for 20 on node 0
[ 1.067889] alloc kstat_irqs on node 0
[ 1.067905] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 1.067910] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 1.070301] mmc0: SDHCI controller on PCI [0000:02:05.1] using DMA
[ 1.070459] firewire_ohci 0000:02:05.0: enabling device (0100 -> 0102)
[ 1.071129] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
[ 1.071146] firewire_ohci 0000:02:05.0: PCI INT A -> Link[LNK1] -> GSI 5 (level, low) -> IRQ 5
[ 1.140107] ssb: Sonics Silicon Backplane found on PCI device 0000:03:00.0
[ 1.230366] ata1.00: ATAPI: PIGNEER DVDRW DVR-C17B, 1.02, max MWDMA2
[ 1.230397] ata1: nv_mode_filter: 0x39f&0x739f->0x39f, BIOS=0x0 (0xc600) ACPI=0x39f (120:600:0x12)
[ 1.260031] usb 3-4: new full speed USB device using ohci_hcd and address 2
[ 1.270311] ata1.00: configured for MWDMA2
[ 1.283364] scsi 0:0:0:0: CD-ROM PAOFEER DVDRW DVR%K17B 1&02 PQ: 0 ANSI: 5
[ 1.306543] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.306549] Uniform CD-ROM driver Revision: 3.20
[ 1.306717] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.306816] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.306922] ata2: port disabled. ignoring.
[ 1.310776] firewire_ohci: Added fw-ohci device 0000:02:05.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x0
[ 1.591111] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1b:24:b2:42:b1
[ 1.591117] forcedeth 0000:00:0a.0: highdma pwrctl mgmt lnktim msi desc-v3
[ 1.591216] ahci 0000:00:09.0: version 3.0
[ 1.591232] ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 23 (level, low) -> IRQ 23
[ 1.591276] ahci 0000:00:09.0: controller can do NCQ, turning on CAP_NCQ
[ 1.591279] ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP
[ 1.591349] ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[ 1.591354] ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio slum part
[ 1.591359] ahci 0000:00:09.0: setting latency timer to 64
[ 1.591938] scsi2 : ahci
[ 1.592246] scsi3 : ahci
[ 1.592355] scsi4 : ahci
[ 1.592449] scsi5 : ahci
[ 1.592651] ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 23
[ 1.592655] ata4: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484180 irq 23
[ 1.592659] ata5: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484200 irq 23
[ 1.592662] ata6: SATA max UDMA/133 abar m8192@0xf6484000 port 0xf6484280 irq 23
[ 1.790170] firewire_core: created device fw0: GUID 00241b002b906900, S400
[ 1.940035] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.940045] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.940065] usb 4-2: new full speed USB device using ohci_hcd and address 2
[ 1.940076] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.120026] usb 4-2: device descriptor read/64, error -62
[ 2.340030] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.340489] ata3.00: ATA-7: TOSHIBA MK1637GSX, DL032C, max UDMA/100
[ 2.340493] ata3.00: 312581808 sectors, multi 16: LBA48
[ 2.341034] ata3.00: configured for UDMA/100
[ 2.341209] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1637GS DL03 PQ: 0 ANSI: 5
[ 2.341480] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.341606] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 2.341667] sd 2:0:0:0: [sda] Write Protect is off
[ 2.341670] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.341697] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.341898] sda: sda1 sda2 <
[ 2.422528] usb 4-2: device descriptor read/64, error -62
[ 2.438740] sda5 >
[ 2.439122] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.720039] usb 4-2: new full speed USB device using ohci_hcd and address 3
[ 2.770606] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 2.902555] usb 4-2: device descriptor read/64, error -62
[ 3.202549] usb 4-2: device descriptor read/64, error -62
[ 3.492555] usb 4-2: new full speed USB device using ohci_hcd and address 4
[ 3.912543] usb 4-2: device not accepting address 4, error -62
[ 4.092534] usb 4-2: new full speed USB device using ohci_hcd and address 5
[ 4.512536] usb 4-2: device not accepting address 5, error -62
[ 4.512557] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 5.191438] Adding 4311036k swap on /dev/sda5. Priority:-1 extents:1 across:4311036k
[ 6.451213] udev[442]: starting version 163
[ 6.522834] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 8.079459] type=1400 audit(1294004888.782:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=603 comm="apparmor_parser"
[ 8.079801] type=1400 audit(1294004888.782:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=603 comm="apparmor_parser"
[ 8.079994] type=1400 audit(1294004888.782:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=603 comm="apparmor_parser"
[ 9.479186] input: HP WMI hotkeys as /devices/virtual/input/input5
[ 9.764056] lp: driver loaded but no devices found
[ 9.984180] acpi device:23: registered as cooling_device2
[ 9.984425] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 9.984501] ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no)
[ 10.246481] cfg80211: Calling CRDA to update world regulatory domain
[ 10.368862] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 10.391718] i2c i2c-0: nForce2 SMBus adapter at 0x3040
[ 10.391752] i2c i2c-1: nForce2 SMBus adapter at 0x3000
[ 10.577697] Linux video capture interface: v2.00
[ 10.606952] gspca: main v2.9.0 registered
[ 10.722181] gspca: probing 093a:2600
[ 10.745564] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000/0x0
[ 10.752990] input: pac7311 as /devices/pci0000:00/0000:00:02.0/usb3/3-4/input/input7
[ 10.753182] gspca: video0 created
[ 10.753186] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 10.753231] usbcore: registered new interface driver pac7311
[ 10.753234] pac7311: registered
[ 10.802107] EDAC MC: Ver: 2.1.0 Dec 2 2010
[ 10.825169] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[ 10.977979] r852 0000:02:05.3: PCI INT B -> Link[LNK2] -> GSI 7 (level, low) -> IRQ 7
[ 10.978504] r852: Non dma capable device detected, dma disabled
[ 10.978524] r852: driver loaded succesfully
[ 11.152252] EDAC amd64_edac: Ver: 3.3.0 Dec 2 2010
[ 11.152437] EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
[ 11.152448] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 11.152450] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 11.152452] (Note that use of the override may cause unknown side effects.)
[ 11.152676] amd64_edac: probe of 0000:00:18.2 failed with error -22
[ 11.191249] b43-phy0: Broadcom 4311 WLAN found (core revision 13)
[ 11.741918] phy0: Selected rate control algorithm 'minstrel'
[ 11.743041] Registered led device: b43-phy0::tx
[ 11.743170] Registered led device: b43-phy0::rx
[ 11.743208] Registered led device: b43-phy0::radio
[ 11.743514] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
[ 11.926536] cfg80211: World regulatory domain updated:
[ 11.926541] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.926545] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.926548] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.926551] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.926554] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.926557] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.663928] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 13.663936] alloc irq_desc for 21 on node 0
[ 13.663939] alloc kstat_irqs on node 0
[ 13.663954] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[ 13.663959] hda_intel: Disable MSI for Nvidia chipset
[ 13.664016] HDA Intel 0000:00:07.0: setting latency timer to 64
[ 14.161508] nvidia: module license 'NVIDIA' taints kernel.
[ 14.161513] Disabling lock debugging due to kernel taint
[ 14.453535] type=1400 audit(1294004895.162:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=938 comm="apparmor_parser"
[ 14.453887] type=1400 audit(1294004895.162:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=938 comm="apparmor_parser"
[ 14.454087] type=1400 audit(1294004895.162:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=938 comm="apparmor_parser"
[ 14.488888] type=1400 audit(1294004895.192:8): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=937 comm="apparmor_parser"
[ 14.824996] type=1400 audit(1294004895.532:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=943 comm="apparmor_parser"
[ 14.825447] type=1400 audit(1294004895.532:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=943 comm="apparmor_parser"
[ 14.949542] type=1400 audit(1294004895.652:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=983 comm="apparmor_parser"
[ 15.051750] type=1400 audit(1294004895.752:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=939 comm="apparmor_parser"
[ 15.056274] type=1400 audit(1294004895.762:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=939 comm="apparmor_parser"
[ 15.059166] type=1400 audit(1294004895.762:14): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=939 comm="apparmor_parser"
[ 15.171496] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 16
[ 15.171504] alloc irq_desc for 16 on node 0
[ 15.171507] alloc kstat_irqs on node 0
[ 15.171522] nvidia 0000:00:12.0: PCI INT A -> Link[LGPU] -> GSI 16 (level, low) -> IRQ 16
[ 15.171531] nvidia 0000:00:12.0: setting latency timer to 64
[ 15.171538] vgaarb: device changed decodes: PCI:0000:00:12.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 15.171869] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.28 Wed Sep 29 09:44:58 PDT 2010
[ 16.038769] ppdev: user-space parallel port driver
[ 17.988634] alloc irq_desc for 42 on node 0
[ 17.988640] alloc kstat_irqs on node 0
[ 17.988652] forcedeth 0000:00:0a.0: irq 42 for MSI/MSI-X
[ 17.988862] eth0: no link during initialization.
[ 17.989703] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.630054] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 18.870734] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.909940] cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12) on phy0
[ 24.785093] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 32.428663] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 60.112995] wlan0: authenticate with 00:1f:9f:f3:5c:59 (try 1)
[ 60.114484] wlan0: authenticated
[ 60.114916] wlan0: associate with 00:1f:9f:f3:5c:59 (try 1)
[ 60.117133] wlan0: RX AssocResp from 00:1f:9f:f3:5c:59 (capab=0x411 status=0 aid=1)
[ 60.117138] wlan0: associated
[ 60.118381] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 60.986807] Intel AES-NI instructions are not detected.
[ 61.039449] padlock: VIA PadLock not detected.
[ 70.782522] wlan0: no IPv6 routers present
[ 86.010046] Clocksource tsc unstable (delta = -77646814 ns)
[ 136.729521] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 148.186612] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 1509.229498] usb 3-4: USB disconnect, address 2
[ 1509.230437] gspca: video0 disconnect
[ 1509.260463] gspca: video0 released
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ k during initialization.
k during initialization.
[ 17.989703] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.630054] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 18.870734] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.909940] cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12) on phy0
[ 24.785093] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 32.428663] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 60.112995] wlan0: authenticate with 00:1f:9f:f3:5c:59 (try 1)
[ 60.114484] wlan0: authenticated
[ 60.114916] wlan0: associate with 00:1f:9f:f3:5c:59 (try 1)
[ 60.117133] wlan0: RX AssocResp from 00:1f:9f:f3:5c:59 (capab=0x411 status=0 aid=1)
[ 60.117138] wlan0: associated
[ 60.118381] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 60.986807] Intel AES-NI instructions are not detected.
[ 61.039449] padlock: VIA PadLock not detected.
[ 70.782522] wlan0: no IPv6 routers present
[ 86.010046] Clocksource tsc unstable (delta = -77646814 ns)
[ 136.729521] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 148.186612] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 1509.229498] usb 3-4: USB disconnect, address 2
[ 1509.230437] gspca: video0 disconnect
[ 1509.260463] gspca: video0 released
k : commande introuvable
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 17.989703] ADDRCONF(NETDEV_UP): eth0: link is not ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 18.630054] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 18.870734] ADDRCONF(NETDEV_UP): wlan0: link is not ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 20.909940] cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12) on phy0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 24.785093] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 32.428663] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.112995] wlan0: authenticate with 00:1f:9f:f3:5c:59 (try 1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.114484] wlan0: authenticated
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.114916] wlan0: associate with 00:1f:9f:f3:5c:59 (try 1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.117133] wlan0: RX AssocResp from 00:1f:9f:f3:5c:59 (capab=0x411 status=0 aid=1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.117138] wlan0: associated
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.118381] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.986807] Intel AES-NI instructions are not detected.
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 61.039449] padlock: VIA PadLock not detected.
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 70.782522] wlan0: no IPv6 routers present
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 86.010046] Clocksource tsc unstable (delta = -77646814 ns)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 136.729521] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 148.186612] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.229498] usb 3-4: USB disconnect, address 2
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.230437] gspca: video0 disconnect
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.260463] gspca: video0 released
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ k during initialization.
k : commande introuvable
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 17.989703] ADDRCONF(NETDEV_UP): eth0: link is not ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 18.630054] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 18.870734] ADDRCONF(NETDEV_UP): wlan0: link is not ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 20.909940] cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12) on phy0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 24.785093] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 32.428663] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.112995] wlan0: authenticate with 00:1f:9f:f3:5c:59 (try 1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.114484] wlan0: authenticated
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.114916] wlan0: associate with 00:1f:9f:f3:5c:59 (try 1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.117133] wlan0: RX AssocResp from 00:1f:9f:f3:5c:59 (capab=0x411 status=0 aid=1)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.117138] wlan0: associated
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.118381] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 60.986807] Intel AES-NI instructions are not detected.
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 61.039449] padlock: VIA PadLock not detected.
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 70.782522] wlan0: no IPv6 routers present
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 86.010046] Clocksource tsc unstable (delta = -77646814 ns)
bash: Erreur de syntaxe près du symbole inattendu « ( »
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 136.729521] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 148.186612] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.229498] usb 3-4: USB disconnect, address 2
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.230437] gspca: video0 disconnect
bash: [: « ] » manquant
moi@moi-HP-Pavilion-dv9500-Notebook-PC:~$ [ 1509.260463] gspca: video0 released
bash: [: « ] » manquant

Stemp · Le 03/01/2011, à 00:44

Effectivement il y aurait bien un soucis avec tes ports usb.

Problème sur un port usb 1.1 :

[    2.422528] usb 4-2: device descriptor read/64, error -62
[    2.720039] usb 4-2: new full speed USB device using ohci_hcd and address 3
[    2.902555] usb 4-2: device descriptor read/64, error -62
[    3.202549] usb 4-2: device descriptor read/64, error -62
[    3.492555] usb 4-2: new full speed USB device using ohci_hcd and address 4
[    3.912543] usb 4-2: device not accepting address 4, error -62
[    4.092534] usb 4-2: new full speed USB device using ohci_hcd and address 5
[    4.512536] usb 4-2: device not accepting address 5, error -62
[    4.512557] hub 4-0:1.0: unable to enumerate USB device on port 2

Par contre il trouve bien une webcam, et installe le driver gspca pac7311 :

[   10.577697] Linux video capture interface: v2.00
[   10.606952] gspca: main v2.9.0 registered
[   10.722181] gspca: probing 093a:2600
[   10.745564] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000/0x0
[   10.752990] input: pac7311 as /devices/pci0000:00/0000:00:02.0/usb3/3-4/input/input7
[   10.753182] gspca: video0 created
[   10.753186] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[   10.753231] usbcore: registered new interface driver pac7311
[   10.753234] pac7311: registered

Malheureusement ensuite ça merdouille et il enlève tout :

[  136.729521] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[  148.186612] gspca: found int in endpoint: 0x83, buffer_len=2, interval=50
[ 1509.229498] usb 3-4: USB disconnect, address 2
[ 1509.230437] gspca: video0 disconnect
[ 1509.260463] gspca: video0 released

En gros je dirais qu'il y a bien un gros problème avec l'usb

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 02/01/2011, à 17:55

webcam sur paviliondv9605

#2 Le 02/01/2011, à 20:57

Re : webcam sur paviliondv9605

#3 Le 02/01/2011, à 21:22

Re : webcam sur paviliondv9605

#4 Le 03/01/2011, à 00:10

Re : webcam sur paviliondv9605

#5 Le 03/01/2011, à 00:15

Re : webcam sur paviliondv9605

#6 Le 03/01/2011, à 00:44

Re : webcam sur paviliondv9605

Pied de page des forums