Ubuntu-fr

christianT65

Clé USB

Bonjour,
Je viens d'installer Ubuntu 6.06 sur mon nouveau PC, d'après les journeaux système il semble reconnaitre les ports USB

Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

mais rien ne se passe... Ou plutôt si, chaque fois que je branche une clé USB qui marchait sous w%§s, elle n'existe plus après. Si je la branche sur un autre PC plus rien ne se passe.
J'en suis à 2 clé apparament mortes plus un appareil photo dont la connexion USB ne fonctionne plus.
Comment faire marcher tout ça.

Proc. AMD Sempron 3200
CM. Gigabyte GA-M51GM-S2G (chipset NForce)
Kernel 2.6.15-26-amd64-generic

Merci

christianT65

Re : Clé USB

Mon dmesg
christian@Christian:~$ dmesg
[    0.000000] Bootdata ok (command line is root=/dev/sda1 ro quiet splash)
[    0.000000] Linux version 2.6.15-26-amd64-generic (buildd@king) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Mon Jul 17 19:50:04 UTC 2006
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
[    0.000000]  BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001c000000 - 0000000020000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[    0.000000] ACPI: RSDP (v000 GBT                                   ) @ 0x0000 0000000f6ac0
[    0.000000] ACPI: RSDT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 000000001bff3000
[    0.000000] ACPI: FADT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 000000001bff3040
[    0.000000] ACPI: SSDT (v001 PTLTD  POWERNOW 0x00000001  LTP 0x00000001) @ 0x 000000001bff79c0
[    0.000000] ACPI: MCFG (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 000000001bff7ac0
[    0.000000] ACPI: MADT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 000000001bff7940
[    0.000000] ACPI: DSDT (v001 GBT    AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x 0000000000000000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] Number of nodes 1
[    0.000000] Node 0 MemBase 0000000000000000 Limit 000000001bff0000
[    0.000000] Using 63 for the hash shift.
[    0.000000] Using node hash shift of 63
[    0.000000] Bootmem setup node 0 0000000000000000-000000001bff0000
[    0.000000] On node 0 totalpages: 112080
[    0.000000]   DMA zone: 3015 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 109065 pages, LIFO batch:31
[    0.000000]   Normal zone: 0 pages, LIFO batch:0
[    0.000000]   HighMem zone: 0 pages, LIFO batch:0
[    0.000000] Nvidia board detected. Ignoring ACPI timer override.
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:15 APIC version 16
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Setting APIC routing to physical flat
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:d000 0000)
[    0.000000] Checking aperture...
[    0.000000] CPU 0: aperture @ 77ba000000 size 32 MB
[    0.000000] Aperture from northbridge cpu 0 too small (32 MB)
[    0.000000] No AGP bridge found
[    0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] Built 1 zonelists
[    0.000000] Kernel command line: root=/dev/sda1 ro quiet splash
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 65536 bytes)
[    0.000000] time.c: Using 3.579545 MHz PM timer.
[    0.000000] time.c: Detected 1808.240 MHz processor.
[   25.397458] Console: colour VGA+ 80x25
[   25.397878] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[   25.398531] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[   25.403916] Memory: 440280k/458688k available (2150k kernel code, 18020k rese rved, 757k data, 180k init)
[   25.480517] Calibrating delay using timer specific routine.. 3622.08 BogoMIPS  (lpj=7244161)
[   25.480572] Security Framework v1.0.0 initialized
[   25.480577] SELinux:  Disabled at boot.
[   25.480600] Mount-cache hash table entries: 256
[   25.480719] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[   25.480722] CPU: L2 Cache: 128K (64 bytes/line)
[   25.480725] CPU 0(1) -> Node 0 -> Core 0
[   25.480733] mtrr: v2.0 (20020519)
[   25.480741] SMP alternatives: switching to UP code
[   25.481015] checking if image is initramfs... it is
[   26.083868] Freeing initrd memory: 7097k freed
[   26.092456] ACPI: Looking for DSDT ... not found!
[   26.136824] Using local APIC timer interrupts.
[   26.192102] Detected 12.557 MHz APIC timer.
[   26.192167] Brought up 1 CPUs
[   26.192218] time.c: Using PIT/TSC based timekeeping.
[   26.192221] testing NMI watchdog ... OK.
[   26.232568] NET: Registered protocol family 16
[   26.232598] ACPI: bus type pci registered
[   26.232663] PCI: Using configuration type 1
[   26.236399] PCI: Using MMCONFIG at f0000000
[   26.236996] ACPI: Subsystem revision 20051216
[   26.244161] ACPI: Interpreter enabled
[   26.244166] ACPI: Using IOAPIC for interrupt routing
[   26.244686] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   26.244690] PCI: Probing PCI hardware (bus 00)
[   26.248599] Boot video device is 0000:00:05.0
[   26.249384] PCI: Transparent bridge - 0000:00:10.0
[   26.249432] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   26.357287] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[   26.358921] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.359253] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.359589] ACPI: PCI Interrupt Link [LNK3] (IRQs *5 7 9 10 11 14 15)
[   26.359915] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.360266] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.360599] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.360928] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)
[   26.361254] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.361586] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
[   26.361915] ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.362244] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[   26.362574] ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.362901] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[   26.363227] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.363560] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.363892] ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
[   26.364251] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
[   26.364583] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[   26.364909] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
[   26.365238] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
[   26.365660] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[   26.366072] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[   26.366485] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[   26.366891] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[   26.367296] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[   26.367704] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[   26.368163] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[   26.368599] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[   26.369007] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[   26.369414] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[   26.369826] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[   26.370233] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[   26.370652] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[   26.371065] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
[   26.371475] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[   26.371885] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[   26.372320] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[   26.372735] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[   26.373153] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[   26.373564] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[   26.373972] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[   26.376837] Linux Plug and Play Support v0.97 (c) Adam Belay
[   26.376852] pnp: PnP ACPI init
[   26.382770] pnp: PnP ACPI: found 13 devices
[   26.382786] PCI: Using ACPI for IRQ routing
[   26.382792] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   26.382921] PCI-DMA: Disabling IOMMU.
[   26.383563] pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
[   26.383568] pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
[   26.383573] pnp: 00:00: ioport range 0x1400-0x147f has been reserved
[   26.383576] pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
[   26.383579] pnp: 00:00: ioport range 0x1800-0x187f has been reserved
[   26.383582] pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
[   26.383585] pnp: 00:00: ioport range 0x2000-0x207f has been reserved
[   26.383588] pnp: 00:00: ioport range 0x2080-0x20ff has been reserved
[   26.383784] PCI: Bridge: 0000:00:02.0
[   26.383787]   IO window: 8000-8fff
[   26.383790]   MEM window: disabled.
[   26.383792]   PREFETCH window: disabled.
[   26.383794] PCI: Bridge: 0000:00:03.0
[   26.383797]   IO window: 9000-9fff
[   26.383799]   MEM window: disabled.
[   26.383800]   PREFETCH window: disabled.
[   26.383803] PCI: Bridge: 0000:00:04.0
[   26.383805]   IO window: a000-afff
[   26.383807]   MEM window: disabled.
[   26.383809]   PREFETCH window: disabled.
[   26.383811] PCI: Bridge: 0000:00:10.0
[   26.383813]   IO window: disabled.
[   26.383816]   MEM window: f5000000-f50fffff
[   26.383819]   PREFETCH window: disabled.
[   26.383830] PCI: Setting latency timer of device 0000:00:02.0 to 64
[   26.383835] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   26.383841] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   26.383848] PCI: Setting latency timer of device 0000:00:10.0 to 64
[   26.384135] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
[   26.384438] audit: initializing netlink socket (disabled)
[   26.384451] audit(1154252337.992:1): initialized
[   26.384584] VFS: Disk quotas dquot_6.5.1
[   26.384604] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[   26.384659] Initializing Cryptographic API
[   26.384663] io scheduler noop registered
[   26.384671] io scheduler anticipatory registered
[   26.384678] io scheduler deadline registered
[   26.384693] io scheduler cfq registered
[   26.384968] PCI: Setting latency timer of device 0000:00:02.0 to 64
[   26.384973] pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS
[   26.384988] assign_interrupt_mode Found MSI capability
[   26.385022] Allocate Port Service[pcie00]
[   26.385057] Allocate Port Service[pcie03]
[   26.385089] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   26.385092] pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS
[   26.385106] assign_interrupt_mode Found MSI capability
[   26.385124] Allocate Port Service[pcie00]
[   26.385150] Allocate Port Service[pcie03]
[   26.385179] PCI: Setting latency timer of device 0000:00:04.0 to 64
[   26.385182] pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS
[   26.385197] assign_interrupt_mode Found MSI capability
[   26.385214] Allocate Port Service[pcie00]
[   26.385242] Allocate Port Service[pcie03]
[   26.398853] Real Time Clock Driver v1.12
[   26.398894] Linux agpgart interface v0.101 (c) Dave Jones
[   26.398986] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq  1,12
[   26.399161] serio: i8042 AUX port at 0x60,0x64 irq 12
[   26.399208] serio: i8042 KBD port at 0x60,0x64 irq 1
[   26.399245] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing  enabled
[   26.399364] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   26.399525] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   26.401931] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   26.402185] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   26.402649] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 bloc ksize
[   26.402697] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   26.402700] ide: Assuming 33MHz system bus speed for PIO modes; override with  idebus=xx
[   26.402869] mice: PS/2 mouse device common for all mice
[   26.402995] NET: Registered protocol family 2
[   26.425444] input: AT Translated Set 2 keyboard as /class/input/input0
[   26.444038] IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
[   26.444184] TCP established hash table entries: 16384 (order: 6, 262144 bytes )
[   26.444387] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[   26.444622] TCP: Hash tables configured (established 16384 bind 16384)
[   26.444626] TCP reno registered
[   26.444708] TCP bic registered
[   26.444716] NET: Registered protocol family 1
[   26.444723] NET: Registered protocol family 8
[   26.444725] NET: Registered protocol family 20
[   26.444866] ACPI wakeup devices:
[   26.444869] HUB0 XVRA XVRB XVRC USB0 USB2 AZAD MMAC MMCI UAR1
[   26.444875] ACPI: (supports S0 S1 S4 S5)
[   26.444946] Freeing unused kernel memory: 180k freed
[   26.493792] vga16fb: initializing
[   26.493797] vga16fb: mapped to 0xffff8100000a0000
[   26.686351] Console: switching to colour frame buffer device 80x25
[   26.686359] fb0: VGA16 VGA frame buffer device
[   27.711193] Capability LSM initialized
[   28.555466] SCSI subsystem initialized
[   28.557398] ACPI: bus type scsi registered
[   28.557402] libata version 1.20 loaded.
[   28.559331] sata_nv 0000:00:0e.0: version 0.8
[   28.559808] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[   28.559813] GSI 16 sharing vector 0xD1 and IRQ 16
[   28.559817] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (lev el, low) -> IRQ 209
[   28.559875] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   28.559951] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 209
[   28.559971] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 209
[   28.766722] ata1: no device found (phy stat 00000000)
[   28.766727] scsi0 : sata_nv
[   29.138683] ata2: dev 0 cfg 00:0040 49:2f00 82:7c6b 83:7f09 84:4773 85:7c68 8 6:3e01 87:4763 88:407f 93:0000
[   29.138689] ata2: dev 0 ATA-7, max UDMA/133, 160084415 sectors: LBA48
[   29.142508] sata_get_dev_handle: SATA dev addr=0xe0000, handle=0xffff81001bfd 1f00
[   29.150725] ata2: dev 0 configured for UDMA/133
[   29.154570] sata_get_dev_handle: SATA dev addr=0xe0000, handle=0xffff81001bfd 1f00
[   29.161797] scsi1 : sata_nv
[   29.162783]   Vendor: ATA       Model: Maxtor 6V080E0    Rev: VA11
[   29.162794]   Type:   Direct-Access                      ANSI SCSI revision: 05
[   29.163822] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[   29.163829] GSI 17 sharing vector 0xD9 and IRQ 17
[   29.163833] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 (lev el, low) -> IRQ 217
[   29.163891] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   29.163945] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 217
[   29.163966] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 217
[   29.168603] Driver 'sd' needs updating - please use bus_type methods
[   29.169728] SCSI device sda: 160084415 512-byte hdwr sectors (81963 MB)
[   29.169745] SCSI device sda: drive cache: write back
[   29.173351] SCSI device sda: 160084415 512-byte hdwr sectors (81963 MB)
[   29.173367] SCSI device sda: drive cache: write back
[   29.173373]  sda: sda1 sda2 sda3
[   29.204099] sd 1:0:0:0: Attached scsi disk sda
[   29.370400] ata3: no device found (phy stat 00000000)
[   29.370406] scsi2 : sata_nv
[   29.578284] ata4: no device found (phy stat 00000000)
[   29.578289] scsi3 : sata_nv
[   29.580457] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[   29.580480] NFORCE-MCP51: chipset revision 161
[   29.580483] NFORCE-MCP51: not 100% native mode: will probe irqs later
[   29.580489] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[   29.580499]     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DM A
[   29.580509]     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DM A
[   29.580518] Probing IDE interface ide0...
[   30.317984] hda: _NEC DVD_RW ND-4571A, ATAPI CD/DVD-ROM drive
[   30.989853] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   30.991073] Probing IDE interface ide1...
[   31.571857] hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDM A(33)
[   31.571868] Uniform CD-ROM driver Revision: 3.20
[   31.675616] usbcore: registered new driver usbfs
[   31.675635] usbcore: registered new driver hub
[   31.677185] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
[   31.677192] GSI 18 sharing vector 0xE1 and IRQ 18
[   31.677195] ACPI: PCI Interrupt 0000:00:0b.1[b] -> Link [APCL] -> GSI 21 (lev el, low) -> IRQ 225
[   31.677247] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[   31.677254] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[   31.677288] ehci_hcd 0000:00:0b.1: debug port 1
[   31.677292] PCI: cache line size of 64 is not supported by device 0000:00:0b. 1
[   31.677660] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus numbe r 1
[   31.677673] ehci_hcd 0000:00:0b.1: irq 225, io mem 0xf5104000
[   31.677684] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   31.677758] hub 1-0:1.0: USB hub found
[   31.677766] hub 1-0:1.0: 8 ports detected
[   31.689511] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0 .54.
[   31.710554] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Dri ver (PCI)
[   31.711045] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
[   31.711051] GSI 19 sharing vector 0xE9 and IRQ 19
[   31.711055] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 20 (lev el, low) -> IRQ 233
[   31.711108] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[   31.711114] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[   31.720386] ieee1394: Initialized config rom entry `ip1394'
[   31.785761] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus numbe r 2
[   31.785774] ohci_hcd 0000:00:0b.0: irq 233, io mem 0xf5108000
[   31.786266] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[   31.786271] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 23 (lev el, low) -> IRQ 209
[   31.786278] PCI: Setting latency timer of device 0000:00:14.0 to 64
[   31.786288] forcedeth: using HIGHDMA
[   31.847334] hub 2-0:1.0: USB hub found
[   31.847348] hub 2-0:1.0: 8 ports detected
[   32.309109] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:14.0
[   32.310734] ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
[   32.311216] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[   32.311222] GSI 20 sharing vector 0x32 and IRQ 20
[   32.311225] ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [APC3] -> GSI 18 (lev el, low) -> IRQ 50
[   32.361705] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[50]  MMIO=[f5004000 -f50047ff]  Max Packet=[2048]
[   32.395260] Probing IDE interface ide1...
[   33.014860] Attempting manual resume
[   33.028505] kjournald starting.  Commit interval 5 seconds
[   33.028518] EXT3-fs: mounted filesystem with ordered data mode.
[   33.636260] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0016e60000b40357]
[   40.068206] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   40.939069] NET: Registered protocol family 10
[   40.939178] lo: Disabled Privacy Extensions
[   40.939545] IPv6 over IPv4 tunneling driver
[   41.810418] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   41.825574] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   42.439755] input: PC Speaker as /class/input/input1
[   42.459432] Floppy drive(s): fd0 is 1.44M
[   42.478958] FDC 0 is a post-1991 82077
[   42.486150] nvidia: module license 'NVIDIA' taints kernel.
[   42.491278] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16
[   42.491284] GSI 21 sharing vector 0x3A and IRQ 21
[   42.491288] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APC7] -> GSI 16 (lev el, low) -> IRQ 58
[   42.491297] PCI: Setting latency timer of device 0000:00:05.0 to 64
[   42.491485] NVRM: loading NVIDIA Linux x86_64 Kernel Module  1.0-8762  Mon Ma y 15 13:58:14 PDT 2006
[   43.033633] parport: PnPBIOS parport detected.
[   43.033686] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   43.102465] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[   43.102470] ACPI: PCI Interrupt 0000:00:10.1[b] -> Link [AAZA] -> GSI 22 (lev el, low) -> IRQ 217
[   43.102532] PCI: Setting latency timer of device 0000:00:10.1 to 64
[   43.486776] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS. ..
[   43.555152] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[   43.572783] ts: Compaq touchscreen protocol output
[   44.126860] lp0: using parport0 (interrupt-driven).
[   44.174237] sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
[   44.174242] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[   44.174245] ieee1394: sbp2: Try serialize_io=0 for better performance
[   44.241888] Adding 1052248k swap on /dev/sda2.  Priority:-1 extents:1 across: 1052248k
[   44.376853] EXT3 FS on sda1, internal journal
[   44.552949] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[   44.552954] md: bitmap version 4.39
[   45.075229] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@red hat.com
[   45.671976] cdrom: open failed.
[   46.120662] kjournald starting.  Commit interval 5 seconds
[   46.120724] EXT3 FS on sda3, internal journal
[   46.120729] EXT3-fs: mounted filesystem with ordered data mode.
[   47.672104] NET: Registered protocol family 17
[   51.018697] eth0: no IPv6 routers present
[   53.520631] ACPI: Power Button (FF) [PWRF]
[   53.520642] ACPI: Power Button (CM) [PWRB]
[   53.611321] ibm_acpi: ec object not found
[   53.638699] pcc_acpi: loading...
[   54.114986] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
[   54.115030] powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x8 (1350 mV)
[   54.115034] powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
[   54.115039] cpu_init done, current fid 0xa, vid 0x8
[   58.051284] ppdev: user-space parallel port driver
[   64.053839] Bluetooth: Core ver 2.8
[   64.053847] NET: Registered protocol family 31
[   64.053849] Bluetooth: HCI device and connection manager initialized
[   64.053862] Bluetooth: HCI socket layer initialized
[   64.076761] Bluetooth: L2CAP ver 2.8
[   64.076767] Bluetooth: L2CAP socket layer initialized
[   64.118988] Bluetooth: RFCOMM socket layer initialized
[   64.119008] Bluetooth: RFCOMM TTY layer initialized
[   64.119010] Bluetooth: RFCOMM ver 1.7
[ 5393.914459] eth0: link down.
[ 5413.254924] eth0: link up.
[ 5459.884189] eth0: link down.
[ 5461.099832] eth0: link up.

Moi ça ne me dis pas grand chose...