Pb installation drivers ATI sur portable avec Radeon Xpress200M

LaDameBlanche · Le 11/06/2006, à 18:50

Bonjour à tous !

J'ai installé ubuntu draper ce matin à côté de mon windows sur mon portable HP Pavilion dv5053ea et j'ai voulu installer les drivers d'ATI pour profiter de XGL (j'ai flashé sur les éffets de transparence/3D :lol::lol:).

Pb : impossible soit de démarrer X, soit de les installer.

Alors j'ai commencé par faire une installation automatique avec la dernière version (8.25). Bon installation ok, je redémarre ubuntu, pouf, écran noir. Je redémarre en safe mode et remplace le nouveau xorg.conf par la sauvegarde faite par l'installer d'ati.
j'essaye en suivant les tutos trouvés sur le net (les paquets xorg-fglrx et cie). je reboot, idem.
en lisant le tutorial sur le wifi (celui en anglais), je m'apperçoit qu'il me faut la version 8.24 si je veux que ça marche
je télécharge donc la 8.24, et l'install. Bah non. Au lancement ça dit dans la console :

==================================================
 ATI Technologies Linux Driver Installer/Packager
==================================================
Detected configuration:
Architecture: x86_64 (64-bit)
X Server: Xorg 7.0.0

Detected version of X does not have a matching 'x700_64a' directory
You may override the detected version using the following syntax:
     X_VERSION=<xdir> ./ati-driver-installer-<ver>-<arch>.run [--install]

    x430_64a        XFree86 4.3.x
    x680_64a        X.Org 6.8.x
    x690_64a        X.Org 6.9.x
Removing temporary directory: fglrx-install

Ok, mais sauf que je pige pas comment spécifier la version de X En cherchant un peu sur le net (et en ne trouvant quasiment rien du tout), je trouve un fil de discussion sur lequel un type dit qu'il faut essayer avec la version 32bits. Soit... Et voilà le résultat :

==================================================
 ATI Technologies Linux Driver Installer/Packager
==================================================
Detected configuration:
Architecture: x86_64 (64-bit)
X Server: Xorg 7.0.0

Detected version of X does not have a matching 'x700_64a' directory
You may override the detected version using the following syntax:
     X_VERSION=<xdir> ./ati-driver-installer-<ver>-<arch>.run [--install]

The following values may be used for <xdir>:
    x410        XFree86 4.1.x
    x420        XFree86 4.2.x
    x430        XFree86 4.3.x
    x680        X.Org 6.8.x
    x690        X.Org 6.9.x
Removing temporary directory: fglrx-install

Quelqu'un a-t-il une idée qui pourrait m'aider svp ?

Config :
AMD 64
ATI Radeon Xpress200M
1Go de ram
etc etc etc qui n'a rien à voir.

Merci d'avance.

LaDameBlanche · Le 12/06/2006, à 05:00

Personne ?

LaDameBlanche · Le 13/06/2006, à 07:00

ca se bouscule au portique dites donc

LaDameBlanche · Le 15/06/2006, à 02:02

bon, c'est la dernière fois que je maj ce topic (cette fois de manière intéressante). si personne ne me répond suite à ça, je laisse tomber.

j me suis dis que les contenus des fichiers de config et du log vous intéresseraient...

j'ai essayé d'installer les drivers en suivant le tuto dans la doc sur ce site même. j'ai pas pu faire toutes les étapes, libdri.a n'étant pas présent sur le ddur (amd64)...

Xorg.conf après intallation :

Section "ServerLayout"
	Identifier     "Default Layout"
	Screen         "aticonfig-Screen[0]"
	InputDevice    "Generic Keyboard"
	InputDevice    "Configured Mouse"
	InputDevice    "stylus" "SendCoreEvents"
	InputDevice    "cursor" "SendCoreEvents"
	InputDevice    "eraser" "SendCoreEvents"
	InputDevice    "Synaptics Touchpad"
EndSection

Section "Files"

	# path to defoma fonts
	FontPath     "/usr/share/X11/fonts/misc"
	FontPath     "/usr/share/X11/fonts/cyrillic"
	FontPath     "/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath     "/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath     "/usr/share/X11/fonts/Type1"
	FontPath     "/usr/share/X11/fonts/100dpi"
	FontPath     "/usr/share/X11/fonts/75dpi"
	FontPath     "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load  "i2c"
	Load  "bitmap"
	Load  "ddc"
	Load  "dri"
	Load  "extmod"
	Load  "freetype"
	Load  "glx"
# 	Load  "int10"
	Load  "type1"
	Load  "vbe"
EndSection

Section "InputDevice"
	Identifier  "Generic Keyboard"
	Driver      "kbd"
	Option	    "CoreKeyboard"
	Option	    "XkbRules" "xorg"
	Option	    "XkbModel" "pc105"
	Option	    "XkbLayout" "fr"
	Option	    "XkbVariant" "latin9"
EndSection

Section "InputDevice"
	Identifier  "Configured Mouse"
	Driver      "mouse"
	Option	    "CorePointer"
	Option	    "Device" "/dev/input/mice"
	Option	    "Protocol" "ExplorerPS/2"
	Option	    "ZAxisMapping" "4 5"
	Option	    "Emulate3Buttons" "true"
EndSection

Section "InputDevice"
	Identifier  "Synaptics Touchpad"
	Driver      "synaptics"
	Option	    "SendCoreEvents" "true"
	Option	    "Device" "/dev/psaux"
	Option	    "Protocol" "auto-dev"
	Option	    "HorizScrollDelta" "0"
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "stylus"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "stylus"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "eraser"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "eraser"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "cursor"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "cursor"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

# Section "Monitor"
# 	Identifier   "Écran générique"
# 	Option	    "DPMS"
# EndSection

Section "Monitor"
	Identifier   "Écran générique"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
EndSection

Section "Device"
	Identifier  "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
	Driver      "fglrx"
	BusID       "PCI:1:5:0"
EndSection

# Section "Device"
# 	Identifier  "aticonfig-Device[0]"
# 	Driver      "fglrx"
# EndSection

Section "Screen"
	Identifier "Default Screen"
	Device     "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
	Monitor    "Écran générique"
	DefaultDepth     24
	SubSection "Display"
		Depth     1
		Modes    "1280x800"
	EndSubSection
	SubSection "Display"
		Depth     4
		Modes    "1280x800"
	EndSubSection
	SubSection "Display"
		Depth     8
		Modes    "1280x800"
	EndSubSection
	SubSection "Display"
		Depth     15
		Modes    "1280x800"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes    "1280x800"
	EndSubSection
	SubSection "Display"
		Depth     24
		Modes    "1280x800"
	EndSubSection
EndSection

# Section "Screen"
# 	Identifier "aticonfig-Screen[0]"
# 	Device     "aticonfig-Device[0]"
# 	Monitor    "aticonfig-Monitor[0]"
# 	DefaultDepth     24
# 	SubSection "Display"
# 		Viewport   0 0
# 		Depth     24
# 	EndSubSection
# EndSection

Section "DRI"
	Mode         0666
EndSection

le xorg.conf qui marche (en gros, celui sans acceleration) :

Section "Files"
	FontPath	"/usr/share/X11/fonts/misc"
	FontPath	"/usr/share/X11/fonts/cyrillic"
	FontPath	"/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/Type1"
	FontPath	"/usr/share/X11/fonts/100dpi"
	FontPath	"/usr/share/X11/fonts/75dpi"
	# path to defoma fonts
	FontPath	"/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load	"i2c"
	Load	"bitmap"
	Load	"ddc"
	Load	"dri"
	Load	"extmod"
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"fr"
	Option		"XkbVariant"	"latin9"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ExplorerPS/2"
	Option		"ZAxisMapping"		"4 5"
	Option		"Emulate3Buttons"	"true"
EndSection

Section "InputDevice"
	Identifier	"Synaptics Touchpad"
	Driver		"synaptics"
	Option		"SendCoreEvents"	"true"
	Option		"Device"		"/dev/psaux"
	Option		"Protocol"		"auto-dev"
	Option		"HorizScrollDelta"	"0"
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "stylus"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "stylus"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "eraser"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "eraser"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "cursor"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "cursor"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
	Driver		"ati"
	BusID		"PCI:1:5:0"
EndSection

Section "Monitor"
	Identifier	"Écran générique"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
	Monitor		"Écran générique"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1280x800"
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1280x800"
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1280x800"
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1280x800"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1280x800"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1280x800"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"
	InputDevice     "stylus" "SendCoreEvents"
	InputDevice     "cursor" "SendCoreEvents"
	InputDevice     "eraser" "SendCoreEvents"
	InputDevice	"Synaptics Touchpad"
EndSection

Section "DRI"
	Mode	0666
EndSection

et enfin le log X.org.log.0 :

X Window System Version 7.0.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 7.0
Build Operating System:Linux 2.6.15-ubuntu1 x86_64
Current Operating System: Linux nemesis2 2.6.15-23-amd64-generic #1 SMP PREEMPT Tue May 23 13:45:47 UTC 2006 x86_64
Build Date: 16 March 2006
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Jun 15 01:45:28 2006
(==) Using config file: "/etc/X11/xorg.conf"
Data incomplete in file /etc/X11/xorg.conf
	Undefined Screen "aticonfig-Screen[0]" referenced by ServerLayout "Default Layout".
(EE) Problem parsing the config file
(EE) Error parsing the config file

Fatal server error:
no screens found
(WW) xf86CloseConsole: KDSETMODE failed: Bad file descriptor
(WW) xf86CloseConsole: VT_GETMODE failed: Bad file descriptor

a noter que j'ai modifié le xorg.conf. avant de le faire, le device non commencé avec #, il y avait marqué ati à la place de glrx, le device qui suit n'était pas commenté, idem pour screen et monitor.
en gros j'avais device, screen et monitor en double.

de plus, quand j'ai installé les .deb (comme expliqué dans le tutos), au niveau de module-assistant, il m'a sorti une erreur à propos de kernel-source à propos d'un dossier qui n'existe pas (/usr/src/modules si je me souviens bien).

sinon je crois que c'est tout (à par que fglrx-controle s'est maj après lol).

Si quelqu'un a une idée de comment je dois procéder pour régler tous ces pb... Merci d'avance.

Rappel de ma config :
hp pavilion zv5053ea
amd 64bits
radeon xpress200m

Stemp · Le 15/06/2006, à 02:13

Déplace ta section Section "ServerLayout" à la fin du fichier avant la section DRI

Data incomplete in file /etc/X11/xorg.conf
    Undefined Screen "aticonfig-Screen[0]" referenced by ServerLayout "Default Layout".
(EE) Problem parsing the config file

LaDameBlanche · Le 15/06/2006, à 11:33

J'ai fais ce que tu m'as dit, mais ça disait qu'il ne trouvait pas Default Layout en identifier :
Section "ServerLayout"
Identifier "Default Layout"
Screen "aticonfig-Screen[0]"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
InputDevice "Synaptics Touchpad"
EndSection

Je l'ai alors remplacé par aticonfig-screen[0], mais cette fois, ça disait qu'il trouvait pas de screen.

Et au redémarrage, j'ai alors remplacé Screen "aticonfig-Screen[0]" par Screen "default screen". je fais startx, je vois pdt 1/10eme de secondes mon fond d'écran puis finalement écran noir.

voici le log Xorg :

X Window System Version 7.0.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 7.0
Build Operating System:Linux 2.6.15-ubuntu1 x86_64
Current Operating System: Linux nemesis2 2.6.15-23-amd64-generic #1 SMP PREEMPT Tue May 23 13:45:47 UTC 2006 x86_64
Build Date: 16 March 2006
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu Jun 15 11:15:14 2006
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "aticonfig-Screen[0]"
(**) |-->Screen "Default Screen" (0)
(**) |   |-->Monitor "Écran générique"
(**) |   |-->Device "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
(**) |-->Input Device "Generic Keyboard"
(**) |-->Input Device "Configured Mouse"
(**) |-->Input Device "stylus"
(**) |-->Input Device "cursor"
(**) |-->Input Device "eraser"
(**) |-->Input Device "Synaptics Touchpad"
(WW) The directory "/usr/share/X11/fonts/cyrillic" does not exist.
	Entry deleted from font path.
(**) FontPath set to 

[...]

(II) Module extmod: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
	compiled for 7.0.0, module version = 2.1.0
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules/extensions/libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules/fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.2
	Module class: X.Org Font Renderer
	ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules/libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.1.0
	ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
	compiled for 6.8.99.8, module version = 8.25.18
	Module class: X.Org Video Driver
	ABI class: X.Org Video Driver, version 0.7
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.1
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
	compiled for 6.99.99.904, module version = 1.0.3
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "wacom"
(II) Loading /usr/lib/xorg/modules/input/wacom_drv.so
(II) Module wacom: vendor="X.Org Foundation"
	compiled for 4.3.99.902, module version = 1.0.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.5
(II) Wacom driver level: 47-0.7.2 $
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
	compiled for 4.3.99.902, module version = 1.0.0
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 0.5
(II) ATI Radeon/FireGL: The following chipsets are supported:
	RADEON 9000/9000 PRO (RV250 4966), RADEON 9000 LE (RV250 4967),

[...]

	RADEON 9000 PRO/9100 PRO IGP (RS350 7834),
	MOBILITY RADEON 9000/9100 IGP (RS300M 5835),
	RADEON XPRESS 200 (RS400 5A41), RADEON XPRESS 200M (RS400 5A42),
	RADEON XPRESS 200 (RS480 5954), RADEON XPRESS 200M (RS480 5955),
	RADEON XPRESS 200 (RS482 5974), RADEON XPRESS 200M (RS482 5975),
	RADEON XPRESS 200 (RC410 5A61), RADEON XPRESS 200M (RC410 5A62),
	RADEON X1800 (R520 7100), MOBILITY RADEON X1800 (M58 7101),
	MOBILITY RADEON X1800 (M58 7102), MOBILITY FireGL V7200 (M58 7103),

[...]

(II) Primary Device is: PCI 01:05:0
(II) ATI Proprietary Linux Driver Version Identifier:8.25.18
(II) ATI Proprietary Linux Driver Release Identifier: LGDr8.25g1                           
(II) ATI Proprietary Linux Driver Build Date: May 18 2006 09:58:41
(II) ATI Proprietary Linux Driver Build Information: autobuild-rel-r6-8.25.1-driver-lnx-x86_64-268237
(--) Chipset RADEON XPRESS 200M (RS480 5955) found
(II) resource ranges after xf86ClaimFixedResources() call:
[...]


	[23] -1	0	0x00008410 - 0x0000841f (0x10) IX[b]
	[24] -1	0	0x00008420 - 0x00008420 (0x1) IX[b]
	[25] -1	0	0x00008428 - 0x00008428 (0x1) IX[b]
	[26] -1	0	0x00008424 - 0x00008424 (0x1) IX[b]
	[27] -1	0	0x00008430 - 0x00008430 (0x1) IX[b]
	[28] -1	0	0x00008400 - 0x0000840f (0x10) IX[b]
	[29] -1	0	0x00009000 - 0x000090ff (0x100) IX[b](B)
(II) fglrx(0): pEnt->device->identifier=0x6cdcb0
(II) resource ranges after probing:
	[0] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[...]


	[33] 0	0	0xc01203b0 - 0xc01203bb (0xc) IS[b]
	[34] 0	0	0xc01203c0 - 0xc01203df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) fglrx(0): === [R200PreInit] === begin, [s]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 0.1.0
	ABI class: X.Org Video Driver, version 0.8
(II) fglrx(0): PCI bus 1 card 5 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "DPMS" "true"
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(==) fglrx(0): Gamma Correction for I is 0x06419064
(==) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules/libint10.so
(II) Module int10: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 0.8
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(--) fglrx(0): Chipset: "RADEON XPRESS 200M (RS480 5955)" (Chipset = 0x5955)
(--) fglrx(0): (PciSubVendor = 0x103c, PciSubDevice = 0x30a4)
(--) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI
(--) fglrx(0): Linear framebuffer (phys) at 0xc8000000
(--) fglrx(0): MMIO registers at 0xc0100000
(==) fglrx(0): ROM-BIOS at 0x000c0000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Reloading /usr/lib/xorg/modules/libvbe.so
(II) fglrx(0): VESA BIOS detected
(II) fglrx(0): VESA VBE Version 2.0
(II) fglrx(0): VESA VBE Total Mem: 131072 kB
(II) fglrx(0): VESA VBE OEM: ATI RADEON XPRESS 200M Series
(II) fglrx(0): VESA VBE OEM Software Rev: 1.0
(II) fglrx(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) fglrx(0): VESA VBE OEM Product: MS48
(II) fglrx(0): VESA VBE OEM Product Rev: 01.00
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Reloading /usr/lib/xorg/modules/linux/libdrm.so
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: open result is -1, (No such device or address)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
	compiled for 6.8.99.8, module version = 8.25.18
	ABI class: X.Org Server Extension, version 0.2
(--) fglrx(0): VideoRAM: 131072 kByte, Type: DDR SGRAM / SDRAM
(II) fglrx(0): PCIE card detected
(WW) fglrx(0): board is an unknown third party board, chipset is supported
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/lib/xorg/modules/libddc.so
(II) fglrx(0): Connected Display1: LCD on internal LVDS
(II) fglrx(0): Display1 EDID data ---------------------------
(II) fglrx(0): Manufacturer: LPL  Model: 0  Serial#: 0
(II) fglrx(0): Year: 2005  Week: 0
(II) fglrx(0): EDID Version: 1.2
(II) fglrx(0): Digital Display Input
(II) fglrx(0): Max H-Image Size [cm]: horiz.: 33  vert.: 21
(II) fglrx(0): Gamma: 2.20
(II) fglrx(0): No DPMS capabilities specified; RGB/Color Display
(II) fglrx(0): First detailed timing is preferred mode
(II) fglrx(0): redX: 0.590 redY: 0.344   greenX: 0.323 greenY: 0.534
(II) fglrx(0): blueX: 0.156 blueY: 0.138   whiteX: 0.312 whiteY: 0.328
(II) fglrx(0): Manufacturer's mask: 0
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 71.2 MHz   Image Size:  289 x 21 mm
(II) fglrx(0): h_active: 1280  h_sync: 1328  h_sync_end 1360 h_blank_end 1440 h_border: 0
(II) fglrx(0): v_active: 800  v_sync: 802  v_sync_end 808 v_blanking: 823 v_border: 0
(II) fglrx(0):  LGPhilipsLCD
(II) fglrx(0):  LP154W01-TLA2
(II) fglrx(0): End of Display1 EDID data --------------------
(WW) fglrx(0): Specified desktop setup not supported: 8
(II) fglrx(0): Primary Controller - LCD on internal LVDS
(II) fglrx(0): Internal Desktop Setting: 0x00000004
(II) fglrx(0): POWERplay version 3.  2 power states available:
(II) fglrx(0):   1. 301/250MHz @ 60Hz [enable load balancing]
(II) fglrx(0):   2. 100/133MHz @ 60Hz []
(==) fglrx(0): Qbs disabled
(==) fglrx(0): FAST_SWAP disabled
(==) fglrx(0):  PseudoColor visuals disabled
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(==) fglrx(0): Center Mode is disabled 
(==) fglrx(0): TMDS coherent mode is enabled 
(II) fglrx(0): Total of 14 modes found for primary display.
(--) fglrx(0): Virtual size is 1280x800 (pitch 1280)
(**) fglrx(0): *Mode "1280x800": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x800"   71.25  1280 1328 1360 1440  800 802 808 823
(**) fglrx(0):  Default mode "1280x768": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x768"   71.25  1280 1328 1360 1440  768 786 792 823
(**) fglrx(0):  Default mode "1024x768": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x768"   71.25  1024 1200 1232 1440  768 786 792 823
(**) fglrx(0):  Default mode "848x480": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "848x480"   71.25  848 1112 1144 1440  480 642 648 823
(**) fglrx(0):  Default mode "800x600": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "800x600"   71.25  800 1088 1120 1440  600 702 708 823
(**) fglrx(0):  Default mode "720x576": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x576"   71.25  720 1048 1080 1440  576 690 696 823
(**) fglrx(0):  Default mode "720x480": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x480"   71.25  720 1048 1080 1440  480 642 648 823
(**) fglrx(0):  Default mode "640x480": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x480"   71.25  640 1008 1040 1440  480 642 648 823
(**) fglrx(0):  Default mode "640x400": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x400"   71.25  640 1008 1040 1440  400 602 608 823
(**) fglrx(0):  Default mode "640x350": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x350"   71.25  640 1008 1040 1440  350 577 583 823
(**) fglrx(0):  Default mode "512x384": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "512x384"   71.25  512 944 976 1440  384 594 600 823
(**) fglrx(0):  Default mode "400x300": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "400x300"   71.25  400 888 920 1440  150 702 708 823 doublescan
(**) fglrx(0):  Default mode "320x240": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x240"   71.25  320 848 880 1440  120 642 648 823 doublescan
(**) fglrx(0):  Default mode "320x200": 71.2 MHz (scaled from 0.0 MHz), 49.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x200"   71.25  320 848 880 1440  100 602 608 823 doublescan
(++) fglrx(0): DPI set to (100, 100)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/lib/xorg/modules/libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 0.1.0
	ABI class: X.Org Video Driver, version 0.8
(==) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules/libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
	compiled for 7.0.0, module version = 1.2.0
	ABI class: X.Org Video Driver, version 0.8
(==) fglrx(0): HPV inactive
(==) fglrx(0): FSAA enabled: NO
(==) fglrx(0): FSAA Gamma enabled
(==) fglrx(0): FSAA Multisample Position is fix
(==) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Reloading /usr/lib/xorg/modules/linux/libfglrxdrm.so
(II) fglrx(0): Depth moves disabled by default
(==) fglrx(0): Capabilities: 0x00000000
(==) fglrx(0): CapabilitiesEx: 0x00000000
(==) fglrx(0): cpuFlags: 0x4000001f
(==) fglrx(0): cpuSpeedMHz: 0x0000031b
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(==) fglrx(0): UseFastTLS=0
(==) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] 0	0	0xc0100000 - 0xc010ffff (0x10000) MX[b]
	[1] 0	0	0xc8000000 - 0xcfffffff (0x8000000) MX[b]
	[2] -1	0	0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
	[3] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[b]
	[4] -1	0	0x000c0000 - 0x000effff (0x30000) MX[b]
	[5] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[b]
	[6] -1	0	0xc020a400 - 0xc020a4ff (0x100) MX[b]
	[7] -1	0	0xc0209800 - 0xc02098ff (0x100) MX[b]
	[8] -1	0	0xc0209c00 - 0xc0209cff (0x100) MX[b]
	[9] -1	0	0xc020a000 - 0xc020a0ff (0x100) MX[b]
	[10] -1	0	0xc0206000 - 0xc0207fff (0x2000) MX[b]
	[11] -1	0	0xc0200000 - 0xc0203fff (0x4000) MX[b]
	[12] -1	0	0xc0209000 - 0xc02097ff (0x800) MX[b]
	[13] -1	0	0xc0204000 - 0xc0205fff (0x2000) MX[b]
	[14] -1	0	0xc0003800 - 0xc00038ff (0x100) MX[b]
	[15] -1	0	0xc0003400 - 0xc00034ff (0x100) MX[b]
	[16] -1	0	0xc0003000 - 0xc00033ff (0x400) MX[b]
	[17] -1	0	0xc0002000 - 0xc0002fff (0x1000) MX[b]
	[18] -1	0	0xc0001000 - 0xc0001fff (0x1000) MX[b]
	[19] -1	0	0xc0000000 - 0xc0000fff (0x1000) MX[b]
	[20] -1	0	0xc0100000 - 0xc010ffff (0x10000) MX[b](B)
	[21] -1	0	0xc8000000 - 0xcfffffff (0x8000000) MX[b](B)
	[22] 0	0	0x000a0000 - 0x000affff (0x10000) MS[b]
	[23] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[b]
	[24] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[b]
	[25] 0	0	0x00009000 - 0x000090ff (0x100) IX[b]
	[26] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[b]
	[27] -1	0	0x00000000 - 0x000000ff (0x100) IX[b]
	[28] -1	0	0x0000a000 - 0x0000a0ff (0x100) IX[b]
	[29] -1	0	0x00008410 - 0x0000841f (0x10) IX[b]
	[30] -1	0	0x00008420 - 0x00008420 (0x1) IX[b]
	[31] -1	0	0x00008428 - 0x00008428 (0x1) IX[b]
	[32] -1	0	0x00008424 - 0x00008424 (0x1) IX[b]
	[33] -1	0	0x00008430 - 0x00008430 (0x1) IX[b]
	[34] -1	0	0x00008400 - 0x0000840f (0x10) IX[b]
	[35] -1	0	0x00009000 - 0x000090ff (0x100) IX[b](B)
	[36] 0	0	0xc01203b0 - 0xc01203bb (0xc) IS[b]
	[37] 0	0	0xc01203c0 - 0xc01203df (0x20) IS[b]
(II) fglrx(0): UMM Bus area:     0xc85e9000 (size=0x07a07000)
(II) fglrx(0): UMM area:     0x405e9000 (size=0x07a07000)
(II) fglrx(0): driver needs X.org 6.8.x.y with x.y >= 99.8
(II) fglrx(0): detected X.org 7.0.0.0
(II) Loading extension ATIFGLRXDRI
(II) fglrx(0): doing DRIScreenInit
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: Searching for BusID PCI:1:5:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: drmOpenMinor returns 6
drmOpenByBusid: drmGetBusid reports 
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
[...]

drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card254
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -1023
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) fglrx(0): [drm] DRM interface version 1.0
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:1:5:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0x2000
(II) fglrx(0): [drm] mapped SAREA 0x2000 to 0x2aaaadfbb000
(II) fglrx(0): [drm] framebuffer handle = 0x3000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0):     Name: fglrx
(II) fglrx(0):     Version: 8.25.18
(II) fglrx(0):     Date: May 18 2006
(II) fglrx(0):     Desc: ATI FireGL DRM kernel module
(II) fglrx(0): Kernel Module version matches driver.
(II) fglrx(0): Kernel Module Build Time Information:
(II) fglrx(0):     Build-Kernel UTS_RELEASE:        2.6.15-23-amd64-generic
(II) fglrx(0):     Build-Kernel MODVERSIONS:        no
(II) fglrx(0):     Build-Kernel __SMP__:            no
(II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
(II) fglrx(0): [drm] register handle = 0x00004000
(II) fglrx(0): [pcie] 65536 kB allocated with handle 0xdeadbeef
(II) fglrx(0): [drm] ringbuffer size = 0x00100000 bytes
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 65536
(II) fglrx(0): [drm] texture shared area handle = 0x00008000
(II) fglrx(0): shared FSAAScale=1
(II) fglrx(0): DRI initialization successfull!
(II) fglrx(0): FBADPhys: 0x40000000 FBMappedSize: 0x005e9000
(II) fglrx(0): FBMM initialized for area (0,0)-(1280,1210)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1280,800) (front color buffer - assumption)
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(**) fglrx(0): DPMS enabled
(WW) fglrx(0): Option "VendorName" is not used
(WW) fglrx(0): Option "ModelName" is not used
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
	Screen to screen bit blits
	Solid filled rectangles
	8x8 mono pattern filled rectangles
	Solid Lines
	Dashed Lines
	Offscreen Pixmaps
	Setting up tile and stipple cache:
		30 128x128 slots
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): X context handle = 0x1
(II) fglrx(0): [DRI] installation complete

On dirait que tout est ok, pourtant ça démarre pas, ça fait juste écran noir J'ai l'impression que c'est juste un pb de config d'xorg.conf, mais je vois pas où

Stemp · Le 15/06/2006, à 11:45

En fait je n'avais pas assez regardé et le server layout se trouve bien en début de xorg

Section "ServerLayout"
    Identifier     "Default Layout"
    Screen      0  "aticonfig-Screen[0]" 0 0
    InputDevice    "Generic Keyboard"
    InputDevice    "Configured Mouse"
    InputDevice    "stylus" "SendCoreEvents"
    InputDevice    "cursor" "SendCoreEvents"
    InputDevice    "eraser" "SendCoreEvents"
    InputDevice    "Synaptics Touchpad"
EndSection

Ensuite remplace le nom de ton screen :

Section "Screen"
#    Identifier "Default Screen"
    Indentifier         "aticonfig-Screen[0]"
    Device     "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"

LaDameBlanche · Le 16/06/2006, à 09:25

bonne nouvelle, après les modifications, X redémarre normalement.

mais quand je fais glrxinfo j'obtiens ça dans la console :
Error: couldn't find RGB GLX visual!

idem pour glxgears :
Error: couldn't get an RGB, Double-buffered visual

Par contre, tout juste après le redémarrage, j'ai plein de maj au niveau du kernel linux-restricted, glx, etc... J'imagine que c'est un hasard ^^

Mon xorg.conf :

Section "ServerLayout"
    Identifier     "Default Layout"
    Screen      0   "aticonfig-Screen[0]" 0 0
    InputDevice    "Generic Keyboard"
    InputDevice    "Configured Mouse"
    InputDevice    "stylus" "SendCoreEvents"
    InputDevice    "cursor" "SendCoreEvents"
    InputDevice    "eraser" "SendCoreEvents"
    InputDevice    "Synaptics Touchpad"
EndSection

Section "Files"

    # path to defoma fonts
    FontPath     "/usr/share/X11/fonts/misc"
    FontPath     "/usr/share/X11/fonts/cyrillic"
    FontPath     "/usr/share/X11/fonts/100dpi/:unscaled"
    FontPath     "/usr/share/X11/fonts/75dpi/:unscaled"
    FontPath     "/usr/share/X11/fonts/Type1"
    FontPath     "/usr/share/X11/fonts/100dpi"
    FontPath     "/usr/share/X11/fonts/75dpi"
    FontPath     "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
    Load  "i2c"
    Load  "bitmap"
    Load  "ddc"
    Load  "dri"
    Load  "extmod"
    Load  "freetype"
    Load  "glx"
#     Load  "int10"
    Load  "type1"
    Load  "vbe"
EndSection

Section "InputDevice"
    Identifier  "Generic Keyboard"
    Driver      "kbd"
    Option        "CoreKeyboard"
    Option        "XkbRules" "xorg"
    Option        "XkbModel" "pc105"
    Option        "XkbLayout" "fr"
    Option        "XkbVariant" "latin9"
EndSection

Section "InputDevice"
    Identifier  "Configured Mouse"
    Driver      "mouse"
    Option        "CorePointer"
    Option        "Device" "/dev/input/mice"
    Option        "Protocol" "ExplorerPS/2"
    Option        "ZAxisMapping" "4 5"
    Option        "Emulate3Buttons" "true"
EndSection

Section "InputDevice"
    Identifier  "Synaptics Touchpad"
    Driver      "synaptics"
    Option        "SendCoreEvents" "true"
    Option        "Device" "/dev/psaux"
    Option        "Protocol" "auto-dev"
    Option        "HorizScrollDelta" "0"
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
    Identifier  "stylus"
    Driver      "wacom"
    Option        "Device" "/dev/wacom"          # Change to 
    Option        "Type" "stylus"
    Option        "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
    Identifier  "eraser"
    Driver      "wacom"
    Option        "Device" "/dev/wacom"          # Change to 
    Option        "Type" "eraser"
    Option        "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
    Identifier  "cursor"
    Driver      "wacom"
    Option        "Device" "/dev/wacom"          # Change to 
    Option        "Type" "cursor"
    Option        "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

# Section "Monitor"
#     Identifier   "Écran générique"
#     Option        "DPMS"
# EndSection

Section "Monitor"
    Identifier   "Écran générique"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Device"
    Identifier  "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
    Driver      "fglrx"
    BusID       "PCI:1:5:0"
EndSection

# Section "Device"
#     Identifier  "aticonfig-Device[0]"
#     Driver      "fglrx"
# EndSection

Section "Screen"
    # Identifier "Default Screen"
    Identifier "aticonfig-Screen[0]"
    Device     "ATI Technologies, Inc. Radeon Xpress 200M (RS480)"
    Monitor    "Écran générique"
    DefaultDepth     24
    SubSection "Display"
        Depth     1
        Modes    "1280x800"
    EndSubSection
    SubSection "Display"
        Depth     4
        Modes    "1280x800"
    EndSubSection
    SubSection "Display"
        Depth     8
        Modes    "1280x800"
    EndSubSection
    SubSection "Display"
        Depth     15
        Modes    "1280x800"
    EndSubSection
    SubSection "Display"
        Depth     16
        Modes    "1280x800"
    EndSubSection
    SubSection "Display"
        Depth     24
        Modes    "1280x800"
    EndSubSection
EndSection

# Section "Screen"
#     Identifier "aticonfig-Screen[0]"
#     Device     "aticonfig-Device[0]"
#     Monitor    "aticonfig-Monitor[0]"
#     DefaultDepth     24
#     SubSection "Display"
#         Viewport   0 0
#         Depth     24
#     EndSubSection
# EndSection

Section "DRI"
    Mode         0666
EndSection

J'y suis presque là, je le sens lol

Par contre, dans xorg.log, je trouve ça vers la fin :

(II) Initializing built-in extension XEVIE
[b]No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
No matching visual for __GLcontextMode with visual class = 1 (32774), nplanes = 4294967295
error opening security policy file /etc/X11/xserver/SecurityPolicy[/b]
(**) Option "CoreKeyboard"

??

Dernière modification par LaDameBlanche (Le 16/06/2006, à 09:28)

LaDameBlanche · Le 16/06/2006, à 09:42

Ce faux espoir que j'ai eut...

au redémarrage du portable, la même chose qu'avant. ubuntu se charge, puis là X doit se lancer et non, écran noir.

Je pense qu'il faudrait que je trouve quelqu'un qui a réussi à installer les drivers ati sur un HP pavilion de la série dv5000. parce que là sérieux je vois pas...

dans le log d'xorg, j'ai trouvé ça en plus de ce que j'ai mis dans mon poste juste au dessus :

(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
(**) Option "Device" "/dev/wacom"
(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
(**) Option "Device" "/dev/wacom"
(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
(EE) xf86OpenSerial: Cannot open device /dev/wacom
	No such file or directory.
Error opening /dev/wacom : Invalid argument
Synaptics DeviceInit called
SynapticsCtrl called.
(II) Configured Mouse: ps2EnableDataReporting: succeeded
Synaptics DeviceOn called
(--) Synaptics Touchpad touchpad found
(**) RADEON(0): RADEONSaveScreen(2)
ProcXCloseDevice to close or not ?

Zergy · Le 16/06/2006, à 16:35

/dev/wacom est un périphérique qui correspond à une tablette graphique (rien à voir avec le touchpas hein), donc si tu n'as pas de tablette graphique, les erreurs consernant /dev/wacom sont sans effets.

Edit :
En cherchant "Xpress 200M dapper" sous google, j'ai trouvé le xorg.conf d'un personne utilisant un ATI Xpress 200M qui ne semble pas avoir de problème.
Le fichier xorg.conf (sauvegarde le tien)
Le site en question

Par contre pour l'aide, je ne pourrait pas faire plus, j'ai du NVidia.

Si on ne répond pas, c'est peut être par ce que l'on ne sais pas (même si 4 jour ça fait long)
Si c'est pour utiliser XGL, tu risque de déchanter, c'est encore en cour de dévellopement alors pas forcement super stable/débuggué.

Dernière modification par Zergy (Le 16/06/2006, à 17:36)

organon20005 · Le 16/06/2006, à 18:32

Bonsoir,
pour ce qui le concerne, j'ai une installation en 32 bit sur mon amd 64; les drivers d'ATI n'ayant jamais fonctionnés chez moi en 64 bit (Hoary et Breezy) pour la 3D.

Regarde si quelqu'un a réussi dans les post du forum pour l'architecture 64 bits.
http://forum.ubuntu-fr.org/viewforum.php?id=24

Jette un oeil ici aussi (english only)
http://wiki.cchtml.com/index.php/Ubuntu

bonne recherche

Dernière modification par organon20005 (Le 16/06/2006, à 18:49)

LaDameBlanche · Le 16/06/2006, à 23:11

Zergy ? Je connais ce pseudo (l'avatar aussi je crois )
SWC ? Damechaos ?

Bref, merci pour le xorg, je vais tenter

Pour XGL, je sais que c'est pas encore stable (la fin de l'année m'a-t-on dit), mais j'ai quand même envie d'essayer je suis pas mal persévérante généralement (1semaine que je bosse sur ces fichus drivers lol).

Organon > je pense que c'est ce que je vais faire mais je vais quand même essayer.

vinzdran · Le 07/09/2006, à 13:07

Salut, j'ai exactement le même problème depuis je ne sais combien de temps, je n'en peux plus d'être sans 3D

alors je me demandais, as tu fini par réussir??
je cherche desespérement quelqu'un qui aurait vaincu la machine....
pour info j'ai la même carte sur un Pavilion dv5000 (amd64)

merci, en espérant que je verrai la 3D un jour dans kubuntu.....

xtaz · Le 24/10/2006, à 13:27

Pareil pour moi une ati 128 Xpress 200 M dans un portable Pavilion dv5000 (amd64) 5142 précisement ! Et j'ai testé au moins 10 tuto résultat => 10 réinstallation de ubuntu (enfin à la fin je réinstallais le xorg pour que tout remarche) mais bon j'ai trouvé qu'un seul tuto hyper long et compliqué sur le fonctionnement et j'ai eu beau le suivre à la lettre ça n'a jamais voulu marcher

C'est désespérant...

Si quelqu'un connait une bonne méthode ça serait sympa de la poster !

Antoine.

ghimli · Le 18/01/2007, à 12:07

xtaz, et tous les autres, sur les HP dv5000, c'est solutionné par les derniers pilotes ATI, voir :
http://forum.ubuntu-fr.org/viewtopic.ph … 96#p697096

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 11/06/2006, à 18:50

Pb installation drivers ATI sur portable avec Radeon Xpress200M

#2 Le 12/06/2006, à 05:00

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#3 Le 13/06/2006, à 07:00

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#4 Le 15/06/2006, à 02:02

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#5 Le 15/06/2006, à 02:13

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#6 Le 15/06/2006, à 11:33

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#7 Le 15/06/2006, à 11:45

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#8 Le 16/06/2006, à 09:25

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#9 Le 16/06/2006, à 09:42

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#10 Le 16/06/2006, à 16:35

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#11 Le 16/06/2006, à 18:32

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#12 Le 16/06/2006, à 23:11

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#13 Le 07/09/2006, à 13:07

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#14 Le 24/10/2006, à 13:27

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

#15 Le 18/01/2007, à 12:07

Re : Pb installation drivers ATI sur portable avec Radeon Xpress200M

Pied de page des forums