[Résolu] install accel 3D avant d'installer Beryl

douda · Le 01/04/2007, à 13:21

Bonjour a tous

j'ai un sérieux problème concernant l'activation de l'accélération 3D sur mon Toshiba Satellite m60-103
CPU : model name : Intel(R) Pentium(R) M processor 1.60GHz
GPU: ATI Technologies, Inc. Radeon X600 (RV380) (plus précisément la X600SE (128 Dédié)

j'ai bien testé d'installer les drivers fglrx, j'obtenais 600fps sous glxgears avec 90% d'utilisation CPU :s

avec les drivers ati, je suis a 1200fps sous glxgears avec 30% d'utilisation CPU (je n'ai pas pu descendre en dessous de 20%, je ne comprends pas pourquoi)

dans les deux cas, impossible de lancer fgl_glxgears

Using GLX_SGIX_pbuffer
X Error of failed request:  BadMatch (invalid parameter attributes)
  Major opcode of failed request:  143 (GLX)
  Minor opcode of failed request:  5 (X_GLXMakeCurrent)
  Serial number of failed request:  33
  Current serial number in output stream:  33

Un petit apercu de mon Xorg.conf

# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "ServerLayout"
	Identifier     "Default Layout"
	Screen      0  "aticonfig-Screen[0]" 0 0
	InputDevice    "Generic Keyboard"
	InputDevice    "Configured Mouse"
	InputDevice    "stylus" "SendCoreEvents"
	InputDevice    "cursor" "SendCoreEvents"
	InputDevice    "eraser" "SendCoreEvents"
	InputDevice    "Synaptics Touchpad"
EndSection

Section "Files"

	# path to defoma fonts
	FontPath     "/usr/share/X11/fonts/misc"
	FontPath     "/usr/share/X11/fonts/cyrillic"
	FontPath     "/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath     "/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath     "/usr/share/X11/fonts/Type1"
	FontPath     "/usr/share/X11/fonts/100dpi"
	FontPath     "/usr/share/X11/fonts/75dpi"
	FontPath     "/usr/share/fonts/X11/misc"
	FontPath     "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
        Load    "i2c"
        Load    "bitmap"
        Load    "ddc"
        Load    "dri"
        Load    "extmod"
        Load    "freetype"
        Load    "glx"
        Load    "int10"
        Load    "type1"
        Load    "vbe"
EndSection

Section "InputDevice"
	Identifier  "Generic Keyboard"
	Driver      "kbd"
	Option	    "CoreKeyboard"
	Option	    "XkbRules" "xorg"
	Option	    "XkbModel" "pc105"
	Option	    "XkbLayout" "fr"
	Option	    "XkbOptions" "lv3:ralt_switch"
EndSection

Section "InputDevice"
	Identifier  "Configured Mouse"
	Driver      "mouse"
	Option	    "CorePointer"
	Option	    "Device" "/dev/input/mice"
	Option	    "Protocol" "ExplorerPS/2"
	Option	    "ZAxisMapping" "4 5"
	Option	    "Emulate3Buttons" "true"
EndSection

Section "InputDevice"
	Identifier  "Synaptics Touchpad"
	Driver      "synaptics"
	Option	    "SendCoreEvents" "true"
	Option	    "Device" "/dev/psaux"
	Option	    "Protocol" "auto-dev"
	Option	    "HorizScrollDelta" "0"
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "stylus"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "stylus"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "eraser"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "eraser"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"

                                                      # /dev/input/event
                                                      # for USB
	Identifier  "cursor"
	Driver      "wacom"
	Option	    "Device" "/dev/wacom"          # Change to 
	Option	    "Type" "cursor"
	Option	    "ForceDevice" "ISDV4"               # Tablet PC ONLY
EndSection

Section "Monitor"
	Identifier   "Generic Monitor"
	Option	    "DPMS"
EndSection

Section "Monitor"
	Identifier   "aticonfig-Monitor[0]"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
EndSection

Section "Device"

#       Option 	"AGPMode" "4" # Décommentez si vous avez une carte AGP
#       Option "AGPSize" "128" # Décommentez si vous avec une carte AGP AGP aperture size
	Identifier  "ATI Technologies, Inc. Radeon X600 (RV380)"
	Driver      "ati"
	Option	    "AccelMethod" "XAA" # Use XFree86 Acceleration Architecture
	Option	    "AccelDFS" "1" # mettez à 0 si vous avez une carte AGP
	Option	    "GARTSize" "64"
	Option	    "RingSize" "8"
	Option	    "BufferSize" "2"
	Option	    "EnablePageFlip" "1" # Enable page flipping for 3D apps
	Option	    "ColorTiling" "1"
	Option	    "EnableDepthMoves" "yes"
	Option	    "UseFBDev" "false"
	Option	    "RenderAccel" "true" # Enable the hardware render acceleration
	Option	    "mtrr" "on"
	Option	    "SubPixelOrder" "none"
	Option	    "DPMS"
	Option	    "DynamicClocks" "on"
	BusID       "PCI:1:0:0"
EndSection

Section "Device"
	Identifier  "aticonfig-Device[0]"
	Driver      "ati"
	Option	    "DesktopSetup" "single"
	Option	    "VideoOverlay" "on"
	Option	    "OpenGLOverlay" "off"
	Option	    "TVFormat" "PAL-N"
EndSection

Section "Extensions"
 	Option "RENDER" "Enable"
	Option "Composite" "Enable" 
EndSection

Section "Screen"
	Identifier "Default Screen"
	Device     "ATI Technologies, Inc. Radeon X600 (RV380)"
	Monitor    "Generic Monitor"
	DefaultDepth     24
	SubSection "Display"
		Depth     1
		Modes    "1440x900"
	EndSubSection
	SubSection "Display"
		Depth     4
		Modes    "1440x900"
	EndSubSection
	SubSection "Display"
		Depth     8
		Modes    "1440x900"
	EndSubSection
	SubSection "Display"
		Depth     15
		Modes    "1440x900"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes    "1440x900"
	EndSubSection
	SubSection "Display"
		Depth     24
		Modes    "1440x900"
	EndSubSection
EndSection

Section "Screen"
	Identifier "aticonfig-Screen[0]"
	Device     "aticonfig-Device[0]"
	Monitor    "aticonfig-Monitor[0]"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
	EndSubSection
EndSection

Section "DRI"
        Mode    0666
EndSection

j'ai essayé tous les tutos du site pour essayer d'activer l'accélération, et à chaque échec, j'ai repris mon Xorg.bak

# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
	FontPath	"/usr/share/X11/fonts/misc"
	FontPath	"/usr/share/X11/fonts/cyrillic"
	FontPath	"/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/Type1"
	FontPath	"/usr/share/X11/fonts/100dpi"
	FontPath	"/usr/share/X11/fonts/75dpi"
	FontPath	"/usr/share/fonts/X11/misc"
	# path to defoma fonts
	FontPath	"/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load	"i2c"
	Load	"bitmap"
	Load	"ddc"
	Load	"dri"
	Load	"extmod"
    SubSection "extmod"
        Option    "omit xfree86-dga"
    EndSubSection
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"fr"
	Option		"XkbOptions"	"lv3:ralt_switch"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ExplorerPS/2"
	Option		"ZAxisMapping"		"4 5"
	Option		"Emulate3Buttons"	"true"
EndSection

Section "InputDevice"
	Identifier	"Synaptics Touchpad"
	Driver		"synaptics"
	Option		"SendCoreEvents"	"true"
	Option		"Device"		"/dev/psaux"
	Option		"Protocol"		"auto-dev"
	Option		"HorizScrollDelta"	"0"
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "stylus"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "stylus"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "eraser"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "eraser"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "cursor"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "cursor"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies, Inc. Radeon X600 (RV380)"
	Driver		"fglrx"
	BusID		"PCI:1:0:0"
EndSection

Section "Monitor"
	Identifier	"Generic Monitor"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies, Inc. Radeon X600 (RV380)"
	Monitor		"Generic Monitor"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1440x900"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"
	InputDevice     "stylus" "SendCoreEvents"
	InputDevice     "cursor" "SendCoreEvents"
	InputDevice     "eraser" "SendCoreEvents"
	InputDevice	"Synaptics Touchpad"
EndSection

Section "DRI"
	Mode	0666
EndSection

Je me suis laissé dire que tout se jouait sur le "composite" forcé en Enable que se jouait l'accélération, mais apparement, ce n'est pas le cas

je n'ai, par la meme occasion trouvé aucune info sur la compatibilité de ma carte avec Beryl..., a part le test "--test -only"

douda@douda-laptop:~$    beryl  --test-only
**************************************************************
* Beryl system compatiblity check                            *
**************************************************************

Detected xserver                                : AIGLX

Checking Display :0.0 ...

Checking for XComposite extension               : passed (v0.3)
Checking for XDamage extension                  : passed
Checking for RandR extension                    : passed
Checking for XSync extension                    : passed

Checking Screen 0 ...

Checking for GLX_SGIX_fbconfig                  : passed
Checking for GLX_EXT_texture_from_pixmap        : passed
Checking for non power of two texture support   : failed

Support for non power of two textures missing

Ce test m'a montré, je pense que ma carte ne supporterais peut etre pas Beryl ou ne serait pas compatible
( Checking for non power of two texture support : failed )
à moins que ca ne soit toujours ce fameux problème d'accélération 3D

étant donné que je débute sur Ubuntu, et plus généralement, sur les plates formes Linux en général, si il manque des informations concernant mon problème, n'hésitez a me le dire, que je me perfectionne dans le l'art de résoudre un problème rapidement

Merci a tous,

Douda

Dernière modification par douda (Le 12/09/2007, à 14:06)

douda · Le 01/04/2007, à 13:23

je n'ai pas précisé, ma carte graphique X600SE Mobility est une PCE et non AGP

je n'ai pas voulu tenter le diable en suivant les tutos AGP

Joe Mab · Le 01/04/2007, à 19:40

Bonjourà tous,

je suis désolé mé je ne peux pas résoudre tes problèmes parce que moi aussi j'ai ce problème:

ceci est mon ordi:

Processeur: AMD Mobile AMD Sempon(tm) Processor 3000+
Carte graphique: ATI RADEON XPRESS 200M

et je suis sous Ubuntu Edgy pour l'instant. J'ai suivi ts les tutos pr installer un bon driver pour ma carte, mais je n'arrive à rien.

HELP!!

Tybbow · Le 01/04/2007, à 20:58

D'après ton fichier Xorg, je crois que tu as essayé une installation dîtes "normal" ^^

Essaye de passer par Envy

douda · Le 01/04/2007, à 21:05

je viens a l'instant de réussir a lancer l'accération 3D, mais pas comme je le voulais...
j'ai utilisé ce tuto pour cela : http://doc.ubuntu-fr.org/materiel/ati_p … re_methode

j'ai modifié mon Xorg en conséquence :

# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the /etc/X11/xorg.conf manual page.
# (Type "man /etc/X11/xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
	FontPath	"/usr/share/X11/fonts/misc"
	FontPath	"/usr/share/X11/fonts/cyrillic"
	FontPath	"/usr/share/X11/fonts/100dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/75dpi/:unscaled"
	FontPath	"/usr/share/X11/fonts/Type1"
	FontPath	"/usr/share/X11/fonts/100dpi"
	FontPath	"/usr/share/X11/fonts/75dpi"
	FontPath	"/usr/share/fonts/X11/misc"
	# path to defoma fonts
	FontPath	"/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection

Section "Module"
	Load	"i2c"
	Load	"bitmap"
	Load	"ddc"
	Load	"dri"
	Load	"extmod"
    SubSection "extmod"
        Option    "omit xfree86-dga"
    EndSubSection
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"fr"
	Option		"XkbOptions"	"lv3:ralt_switch"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ExplorerPS/2"
	Option		"ZAxisMapping"		"4 5"
	Option		"Emulate3Buttons"	"true"
EndSection

Section "InputDevice"
	Identifier	"Synaptics Touchpad"
	Driver		"synaptics"
	Option		"SendCoreEvents"	"true"
	Option		"Device"		"/dev/psaux"
	Option		"Protocol"		"auto-dev"
	Option		"HorizScrollDelta"	"0"
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "stylus"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "stylus"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "eraser"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "eraser"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "InputDevice"
  Driver        "wacom"
  Identifier    "cursor"
  Option        "Device"        "/dev/wacom"          # Change to 
                                                      # /dev/input/event
                                                      # for USB
  Option        "Type"          "cursor"
  Option        "ForceDevice"   "ISDV4"               # Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies, Inc. Radeon X600 (RV380)"
	Driver		"fglrx"
	BusID		"PCI:1:0:0"
EndSection

Section "Extensions"
	Option "Composite" "disable"
EndSection

Section "Monitor"
	Identifier	"Generic Monitor"
	Option		"DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies, Inc. Radeon X600 (RV380)"
	Monitor		"Generic Monitor"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1440x900"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1440x900"
	EndSubSection
EndSection

Section "ServerLayout"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"
	InputDevice     "stylus" "SendCoreEvents"
	InputDevice     "cursor" "SendCoreEvents"
	InputDevice     "eraser" "SendCoreEvents"
	InputDevice	"Synaptics Touchpad"
EndSection

Section "DRI"
	Mode	0666
EndSection

Section "ServerFlags"
        Option  "AIGLX" "off"
EndSection

Avec ca, j'ai sous glxgears :

douda@douda-laptop:~$ glxgears -printfps
12384 frames in 5.0 seconds = 2476.751 FPS
12804 frames in 5.0 seconds = 2560.760 FPS
12630 frames in 5.0 seconds = 2525.918 FPS

mais j'ai 100% d'utilisation CPU avec cette config

sous gfl_glxgears :

douda@douda-laptop:~$ fgl_glxgearsUsing GLX_SGIX_pbuffer
2430 frames in 5.0 seconds = 486.000 FPS
2783 frames in 5.0 seconds = 556.600 FPS
2762 frames in 5.0 seconds = 552.400 FPS

toujours avec 100% d'utilisatino CPU...

et a mon grand bonheur, après redémarrage :

douda@douda-laptop:~$  glxinfo | grep "direct rendering"direct rendering: Yes

la principale chose que j'ai compris avec ca mais qui m'embête grandement, c'est que j'ai du désactiver le composite sous Xorg, mais ce qui me fait marrer, c'est que j'ai voulu l'accélération 3D pour lancer Beryl qui lui, est obligé de lancer le composite pour fonctionner...

ah, linux, quand tu nous tiens

douda · Le 01/04/2007, à 21:12

et voila !! je m'en doutais, j'ai activé le composite et redémarré...

sous glxgears

douda@douda-laptop:~$ glxgears -printfps
Xlib:  extension "XFree86-DRI" missing on display ":0.0".
890 frames in 5.2 seconds = 170.275 FPS
912 frames in 5.5 seconds = 164.923 FPS

100% utilisation CPU evidemment ...

sous fgl_glxgears

douda@douda-laptop:~$ fgl_glxgears
Using GLX_SGIX_pbuffer
Xlib:  extension "XFree86-DRI" missing on display ":0.0".
X Error of failed request:  BadMatch (invalid parameter attributes)
  Major opcode of failed request:  142 (GLX)
  Minor opcode of failed request:  5 (X_GLXMakeCurrent)
  Serial number of failed request:  30
  Current serial number in output stream:  30

en résumé, on est bon a attendre la prochaine version stable d'ubuntu Felsty qui, parait-il prends les drivers ATI nativement accélération comprise, espérons que je n'ai pas révé devant un post utopique

ceci dis, je vais essayer quand meme d'installer beryl pour informer Joe sur ce qui peux l'attendre si il se risuqe a ce genre de fantaisie

Dernière modification par douda (Le 01/04/2007, à 21:13)

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 01/04/2007, à 13:21

[Résolu] install accel 3D avant d'installer Beryl

#2 Le 01/04/2007, à 13:23

Re : [Résolu] install accel 3D avant d'installer Beryl

#3 Le 01/04/2007, à 19:40

Re : [Résolu] install accel 3D avant d'installer Beryl

#4 Le 01/04/2007, à 20:58

Re : [Résolu] install accel 3D avant d'installer Beryl

#5 Le 01/04/2007, à 21:05

Re : [Résolu] install accel 3D avant d'installer Beryl

#6 Le 01/04/2007, à 21:12

Re : [Résolu] install accel 3D avant d'installer Beryl

Pied de page des forums