lecteur de carte

serge benamou · Le 29/03/2007, à 22:23

bonjour

j'utilise un portable presario R3365EA et le lecteur de carte ne fonctionne pas. comment dois je m'y prendre?

je suis sous feisty
merci d'avance

G-rom · Le 29/03/2007, à 22:42

si tu es sous feisty tu aurais du poster sous le sujet feisty. Ce genre de module n'est il pas détecté automatiquement normalement ?? Il monte la carte insérée comme un disque USB.
Peut être que ça viens d'une erreur aussi, n'oublie pas que feisty est en beta encore.

NicoA380 · Le 29/03/2007, à 23:04

Fais donc voir un 'lsusb' (avec et sans carte si possible) et 'lspci' s'il te plait, ou aussi la fin du 'dmesg' après avoir inséré une carte (autant que tu as de type de carte dispo).

serge benamou · Le 30/03/2007, à 00:45

salut

voili voilou

fabio@pcdefabio:~$ lsusb
Bus 005 Device 002: ID 0bc2:0500 Seagate RSS LLC
Bus 005 Device 001: ID 0000:0000
Bus 003 Device 003: ID 046d:c50d Logitech, Inc.
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000

fabio@pcdefabio:~$ lspci
00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP AGP Bridge
00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01)
00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01)
00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
00:14.1 IDE interface: ATI Technologies Inc ATI Dual Channel Bus Master PCI IDE Controller
00:14.3 ISA bridge: ATI Technologies Inc Unknown device 434c
00:14.4 PCI bridge: ATI Technologies Inc Unknown device 4342
00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
00:14.6 Modem: ATI Technologies Inc IXP AC'97 Modem (rev 01)
01:05.0 VGA compatible controller: ATI Technologies Inc RS300M AGP [Radeon Mobility 9100IGP]
02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01)
02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01)
02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading Function (rev 01)
02:07.0 USB Controller: NEC Corporation USB (rev 43)
02:07.1 USB Controller: NEC Corporation USB (rev 43)
02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

et enfin

[    0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2
[    0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
[    0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000037f70000 (usable)
[    0.000000]  BIOS-e820: 0000000037f70000 - 0000000037f7d000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000037f7d000 - 0000000037f80000 (ACPI NVS)
[    0.000000]  BIOS-e820: 0000000037f80000 - 0000000038000000 (reserved)
[    0.000000]  BIOS-e820: 0000000047f80000 - 0000000048000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 895MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f6470
[    0.000000] Entering add_active_range(0, 0, 229232) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229232
[    0.000000]   HighMem    229232 ->   229232
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   229232
[    0.000000] On node 0 totalpages: 229232
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1758 pages used for memmap
[    0.000000]   Normal zone: 223378 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6500
[    0.000000] ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x37f79185
[    0.000000] ACPI: FADT (v001 HP     Chinook  0x06040000 ATI  0x000f4240) @ 0x37f7ceed
[    0.000000] ACPI: MADT (v001 PTLTD    APIC   0x06040000  LTP 0x00000000) @ 0x37f7cf61
[    0.000000] ACPI: SSDT (v001 PTLTD  ACPIHT   0x06040000  LTP 0x00000001) @ 0x37f7cfc9
[    0.000000] ACPI: DSDT (v001     HP    SB200 0x06040000 INTL 0x20030509) @ 0x00000000
[    0.000000] ATI board detected. Disabling timer routing over 8254.
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:3 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] Processor #1 15:3 APIC version 20
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 48000000:b6c00000)
[    0.000000] Detected 3000.255 MHz processor.
[   13.663041] Built 1 zonelists.  Total pages: 227442
[   13.663048] Kernel command line: root=UUID=4161de6a-9e21-4cb4-8973-233a2c05de7e ro quiet splash locale=fr_FR
[   13.663226] mapped APIC to ffffd000 (fee00000)
[   13.663229] mapped IOAPIC to ffffc000 (fec00000)
[   13.663232] Enabling fast FPU save and restore... done.
[   13.663236] Enabling unmasked SIMD FPU exception support... done.
[   13.663254] Initializing CPU#0
[   13.663346] PID hash table entries: 4096 (order: 12, 16384 bytes)
[   13.664372] Console: colour VGA+ 80x25
[   13.665397] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   13.666228] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   13.685638] Memory: 897856k/916928k available (1992k kernel code, 18436k reserved, 889k data, 328k init, 0k highmem)
[   13.685649] virtual kernel memory layout:
[   13.685650]     fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
[   13.685651]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   13.685652]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   13.685653]     lowmem  : 0xc0000000 - 0xf7f70000   ( 895 MB)
[   13.685654]       .init : 0xc03d7000 - 0xc0429000   ( 328 kB)
[   13.685655]       .data : 0xc02f2184 - 0xc03d06d4   ( 889 kB)
[   13.685657]       .text : 0xc0100000 - 0xc02f2184   (1992 kB)
[   13.685660] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   13.763261] Calibrating delay using timer specific routine.. 6003.53 BogoMIPS (lpj=12007064)
[   13.763306] Security Framework v1.0.0 initialized
[   13.763312] SELinux:  Disabled at boot.
[   13.763329] Mount-cache hash table entries: 512
[   13.763470] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
[   13.763479] monitor/mwait feature present.
[   13.763481] using mwait in idle threads.
[   13.763488] CPU: Trace cache: 12K uops, L1 D cache: 16K
[   13.763491] CPU: L2 cache: 1024K
[   13.763494] CPU: Physical Processor ID: 0
[   13.763496] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003180 0000441d 00000000 00000000
[   13.763506] Compat vDSO mapped to ffffe000.
[   13.763510] Remapping vsyscall page to ffffe000
[   13.763526] Checking 'hlt' instruction... OK.
[   13.779337] SMP alternatives: switching to UP code
[   13.779681] Early unpacking initramfs... done
[   14.052594] ACPI: Core revision 20060707
[   14.052759] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   14.883039] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
[   14.883069] SMP alternatives: switching to SMP code
[   14.883209] Booting processor 1/1 eip 3000
[   14.893536] Initializing CPU#1
[   14.974189] Calibrating delay using timer specific routine.. 6000.68 BogoMIPS (lpj=12001372)
[   14.974201] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
[   14.974208] monitor/mwait feature present.
[   14.974215] CPU: Trace cache: 12K uops, L1 D cache: 16K
[   14.974218] CPU: L2 cache: 1024K
[   14.974221] CPU: Physical Processor ID: 0
[   14.974224] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003180 0000441d 00000000 00000000
[   14.974609] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
[   14.974652] Total of 2 processors activated (12004.21 BogoMIPS).
[   14.974712] ENABLING IO-APIC IRQs
[   14.974884] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   15.014557] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[   15.014589] ...trying to set up timer (IRQ0) through the 8259A ...  failed.
[   15.014593] ...trying to set up timer as Virtual Wire IRQ... works.
[   15.162029] checking TSC synchronization across 2 CPUs: passed.
[    0.003998] Brought up 2 CPUs
[    0.068492] migration_cost=26
[    0.068813] Booting paravirtualized kernel on bare hardware
[    0.068886] Time: 21:44:35  Date: 02/29/107
[    0.068920] NET: Registered protocol family 16
[    0.069023] EISA bus registered
[    0.069029] ACPI: bus type pci registered
[    0.069086] PCI: PCI BIOS revision 2.10 entry at 0xfd968, last bus=2
[    0.069088] PCI: Using configuration type 1
[    0.069090] Setting up standard PCI resources
[    0.077738] ACPI: Interpreter enabled
[    0.077742] ACPI: Using IOAPIC for interrupt routing
[    0.078326] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.078334] PCI: Probing PCI hardware (bus 00)
[    0.078358] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[    0.079655] Boot video device is 0000:01:05.0
[    0.080204] PCI: Transparent bridge - 0000:00:14.4
[    0.080329] PCI: Bus #04 (-#07) is hidden behind transparent bridge #02 (-#04) (try 'pci=assign-busses')
[    0.080332] Please report the result to linux-kernel to fix this permanently
[    0.080351] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.082509] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[    0.083257] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.084243] ACPI: PCI Interrupt Link [LNK0] (IRQs 5 10 11) *0, disabled.
[    0.084474] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 10 11) *0, disabled.
[    0.084714] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 10 11) *0, disabled.
[    0.084945] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 10 11) *0, disabled.
[    0.132036] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.132053] pnp: PnP ACPI init
[    0.155879] pnp: PnP ACPI: found 10 devices
[    0.155885] PnPBIOS: Disabled by ACPI PNP
[    0.155943] PCI: Using ACPI for IRQ routing
[    0.155946] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.161527] NET: Registered protocol family 8
[    0.161530] NET: Registered protocol family 20
[    0.161747] pnp: 00:07: ioport range 0x200-0x20f has been reserved
[    0.161751] pnp: 00:07: ioport range 0xc14-0xc14 has been reserved
[    0.161753] pnp: 00:07: ioport range 0xc50-0xc52 has been reserved
[    0.161756] pnp: 00:07: ioport range 0xc6c-0xc6c has been reserved
[    0.162108] PCI: Bridge: 0000:00:01.0
[    0.162111]   IO window: 9000-9fff
[    0.162115]   MEM window: d0100000-d01fffff
[    0.162119]   PREFETCH window: e0000000-efffffff
[    0.162136] PCI: Bus 3, cardbus bridge: 0000:02:04.0
[    0.162138]   IO window: 0000a800-0000a8ff
[    0.162142]   IO window: 0000ac00-0000acff
[    0.162147]   PREFETCH window: 50000000-53ffffff
[    0.162151]   MEM window: 5c000000-5fffffff
[    0.162155] PCI: Bus 4, cardbus bridge: 0000:02:04.1
[    0.162157]   IO window: 00001400-000014ff
[    0.162161]   IO window: 00001800-000018ff
[    0.162166]   PREFETCH window: 54000000-57ffffff
[    0.162170]   MEM window: 60000000-63ffffff
[    0.162174] PCI: Bridge: 0000:00:14.4
[    0.162177]   IO window: a000-afff
[    0.162181]   MEM window: d0200000-d02fffff
[    0.162185]   PREFETCH window: 50000000-57ffffff
[    0.162216] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 17 (level, low) -> IRQ 16
[    0.162233] ACPI: PCI Interrupt 0000:02:04.1[b] -> GSI 16 (level, low) -> IRQ 17
[    0.162272] NET: Registered protocol family 2
[    0.199904] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.200119] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.201069] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.201942] TCP: Hash tables configured (established 131072 bind 65536)
[    0.201947] TCP reno registered
[    0.216031] checking if image is initramfs... it is
[    0.761046] Freeing initrd memory: 6744k freed
[    0.761824] audit: initializing netlink socket (disabled)
[    0.761853] audit(1175204675.476:1): initialized
[    0.762062] VFS: Disk quotas dquot_6.5.1
[    0.762085] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.762159] io scheduler noop registered
[    0.762163] io scheduler anticipatory registered
[    0.762165] io scheduler deadline registered
[    0.762177] io scheduler cfq registered (default)
[    0.762509] isapnp: Scanning for PnP cards...
[    1.114048] isapnp: No Plug & Play device found
[    1.142254] Real Time Clock Driver v1.12ac
[    1.142317] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.143004] ACPI: PCI Interrupt 0000:00:14.6[b] -> GSI 5 (level, low) -> IRQ 5
[    1.143013] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[    1.143104] mice: PS/2 mouse device common for all mice
[    1.143817] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[    1.143999] input: Macintosh mouse button emulation as /class/input/input0
[    1.144050] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[    1.144056] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    1.144264] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[    1.154466] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.162101] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.162108] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.162112] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.162116] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.162120] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.162646] EISA: Probing bus 0 at eisa.0
[    1.162656] Cannot allocate resource for EISA slot 1
[    1.162676] Cannot allocate resource for EISA slot 8
[    1.162679] EISA: Detected 0 cards.
[    1.192757] TCP cubic registered
[    1.192768] NET: Registered protocol family 1
[    1.192802] Starting balanced_irq
[    1.192810] Using IPI No-Shortcut mode
[    1.192901] input: AT Translated Set 2 keyboard as /class/input/input1
[    1.192982] ACPI: (supports S0 S3 S4 S5)
[    1.193030]   Magic number: 15:74:754
[    1.193651] Freeing unused kernel memory: 328k freed
[    1.194933] Time: tsc clocksource has been installed.
[    2.410062] Capability LSM initialized
[    2.453917] ACPI: CPU0 (power states: C1[C1] C2[C2])
[    2.453939] ACPI: CPU1 (power states: C1[C1] C2[C2])
[    2.458708] ACPI: Thermal Zone [THRM] (45 C)
[    3.001005] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    3.001054] 8139cp 0000:02:03.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[    3.001058] 8139cp 0000:02:03.0: Try the "8139too" driver instead.
[    3.003676] 8139too Fast Ethernet driver 0.9.28
[    3.003749] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 18
[    3.004118] eth0: RealTek RTL8139 at 0xf8850800, 00:0f:b0:43:80:77, IRQ 18
[    3.004122] eth0:  Identified 8139 chip type 'RTL-8101'
[    3.019235] ieee1394: Initialized config rom entry `ip1394'
[    3.139202] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17
[    3.189141] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]  MMIO=[d0208000-d02087ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    3.189656] usbcore: registered new interface driver usbfs
[    3.189712] usbcore: registered new interface driver hub
[    3.191900] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[    3.191929] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
[    3.191956] ATIIXP: chipset revision 0
[    3.191963] ATIIXP: not 100% native mode: will probe irqs later
[    3.191980]     ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
[    3.192003]     ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
[    3.192024] Probing IDE interface ide0...
[    3.192356] usbcore: registered new device driver usb
[    3.200982] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.481067] hda: IC25N080ATMR04-0, ATA DISK drive
[    4.156546] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    4.178419] Probing IDE interface ide1...
[    4.468216] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[4b3f0200288b4058]
[    4.915769] hdc: _NEC DVD+/-RW ND-6450A, ATAPI CD/DVD-ROM drive
[    5.592537] ide1 at 0x170-0x177,0x376 on irq 15
[    5.595376] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18
[    5.595404] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    5.595734] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[    5.595755] ohci_hcd 0000:00:13.0: irq 18, io mem 0xd0001000
[    5.659058] usb usb1: configuration #1 chosen from 1 choice
[    5.659105] hub 1-0:1.0: USB hub found
[    5.659117] hub 1-0:1.0: 3 ports detected
[    5.766966] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18
[    5.766997] ohci_hcd 0000:00:13.1: OHCI Host Controller
[    5.767036] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[    5.767054] ohci_hcd 0000:00:13.1: irq 18, io mem 0xd0002000
[    5.830871] usb usb2: configuration #1 chosen from 1 choice
[    5.830918] hub 2-0:1.0: USB hub found
[    5.830930] hub 2-0:1.0: 3 ports detected
[    5.938838] ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 17
[    5.938867] ohci_hcd 0000:02:07.0: OHCI Host Controller
[    5.938902] ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 3
[    5.938920] ohci_hcd 0000:02:07.0: irq 17, io mem 0xd0206000
[    6.028492] usb usb3: configuration #1 chosen from 1 choice
[    6.028536] hub 3-0:1.0: USB hub found
[    6.028549] hub 3-0:1.0: 3 ports detected
[    6.134665] ACPI: PCI Interrupt 0000:02:07.1[b] -> GSI 18 (level, low) -> IRQ 19
[    6.134695] ohci_hcd 0000:02:07.1: OHCI Host Controller
[    6.134732] ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 4
[    6.134752] ohci_hcd 0000:02:07.1: irq 19, io mem 0xd0207000
[    6.218433] floppy0: no floppy controllers found
[    6.224318] usb usb4: configuration #1 chosen from 1 choice
[    6.224360] hub 4-0:1.0: USB hub found
[    6.224373] hub 4-0:1.0: 2 ports detected
[    6.330637] ACPI: PCI Interrupt 0000:02:07.2[C] -> GSI 19 (level, low) -> IRQ 18
[    6.330658] ehci_hcd 0000:02:07.2: EHCI Host Controller
[    6.330730] ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 5
[    6.358370] ehci_hcd 0000:02:07.2: irq 18, io mem 0xd0208c00
[    6.358385] ehci_hcd 0000:02:07.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    6.358538] usb usb5: configuration #1 chosen from 1 choice
[    6.358582] hub 5-0:1.0: USB hub found
[    6.358598] hub 5-0:1.0: 5 ports detected
[    6.473562] SCSI subsystem initialized
[    6.479455] libata version 2.20 loaded.
[    6.500794] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
[    6.500810] Uniform CD-ROM driver Revision: 3.20
[    6.501324] hda: max request size: 512KiB
[    6.502347] hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
[    6.502867] hda: cache flushes supported
[    6.502922]  hda: hda1 hda2 < hda5 >
[    6.869176] Attempting manual resume
[    6.869181] swsusp: Resume From Partition 3:5
[    6.869183] PM: Checking swsusp image.
[    6.882660] PM: Resume from disk failed.
[    6.885846] usb 5-1: new high speed USB device using ehci_hcd and address 2
[    6.923072] kjournald starting.  Commit interval 5 seconds
[    6.923084] EXT3-fs: mounted filesystem with ordered data mode.
[    7.155445] usb 5-1: configuration #1 chosen from 1 choice
[    7.645140] usb 3-2: new low speed USB device using ohci_hcd and address 3
[    7.851862] usb 3-2: configuration #1 chosen from 1 choice
[   18.958444] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[   18.983645] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   18.987624] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   19.710024] input: PS/2 Mouse as /class/input/input2
[   19.735371] input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
[   19.826046] Linux agpgart interface v0.102 (c) Dave Jones
[   19.840468] agpgart: Detected Ati IGP9100/M chipset
[   19.846997] agpgart: AGP aperture is 32M @ 0xd2000000
[   19.898744] input: PC Speaker as /class/input/input4
[   20.052086] parport: PnPBIOS parport detected.
[   20.052120] parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
[   20.112667] ieee80211_crypt: registered algorithm 'NULL'
[   20.116396] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   20.116404] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   20.146357] bcm43xx driver
[   20.146512] ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 19
[   20.246360] Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
[   20.246380] Yenta: Enabling burst memory read transactions
[   20.246386] Yenta: Using CSCINT to route CSC interrupts to PCI
[   20.246389] Yenta: Routing CardBus interrupts to PCI
[   20.246396] Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
[   20.482291] Yenta: ISA IRQ mask 0x0e18, PCI irq 16
[   20.482298] Socket status: 30000086
[   20.482304] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[   20.482309] cs: IO port probe 0xa000-0xafff: clean.
[   20.482715] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
[   20.482720] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff
[   20.483009] Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
[   20.483029] Yenta: Using CSCINT to route CSC interrupts to PCI
[   20.483032] Yenta: Routing CardBus interrupts to PCI
[   20.483038] Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
[   20.620637] usbcore: registered new interface driver hiddev
[   20.718079] Yenta: ISA IRQ mask 0x0e18, PCI irq 17
[   20.718085] Socket status: 30000006
[   20.718089] Yenta: Raising subordinate bus# of parent bus (#02) from #04 to #07
[   20.718098] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[   20.718103] cs: IO port probe 0xa000-0xafff: clean.
[   20.718505] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
[   20.718509] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff
[   20.730761] ACPI: PCI Interrupt 0000:00:14.5[b] -> GSI 5 (level, low) -> IRQ 5
[   20.834518] input: Logitech USB Receiver as /class/input/input5
[   20.834619] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:02:07.0-2
[   20.834646] usbcore: registered new interface driver usbhid
[   20.834650] usbcore: registered new interface driver libusual
[   20.834658] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[   20.968654] Initializing USB Mass Storage driver...
[   20.968819] scsi0 : SCSI emulation for USB Mass Storage devices
[   20.968935] usbcore: registered new interface driver usb-storage
[   20.968945] USB Mass Storage support registered.
[   20.969215] usb-storage: device found at 2
[   20.969218] usb-storage: waiting for device to settle before scanning
[   21.258392] ACPI: PCI Interrupt 0000:00:14.6[b] -> GSI 5 (level, low) -> IRQ 5
[   21.390063] cs: IO port probe 0x100-0x3af: clean.
[   21.391180] cs: IO port probe 0x100-0x3af: clean.
[   21.392313] cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
[   21.392811] cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
[   21.393308] cs: IO port probe 0x820-0x8ff: clean.
[   21.393721] cs: IO port probe 0x820-0x8ff: clean.
[   21.394132] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xcd0-0xcd7
[   21.394541] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xcd0-0xcd7
[   21.395083] cs: IO port probe 0xa00-0xaff: clean.
[   21.395550] cs: IO port probe 0xa00-0xaff: clean.
[   23.087290] floppy0: no floppy controllers found
[   23.227888] lp0: using parport0 (interrupt-driven).
[   23.306924] ndiswrapper version 1.38 loaded (preempt=no,smp=yes)
[   23.413939] usbcore: registered new interface driver ndiswrapper
[   23.449478] Adding 2650684k swap on /dev/disk/by-uuid/87da2938-47b9-4ce4-8b25-da9976f0addf.  Priority:-1 extents:1 across:2650684k
[   23.511908] EXT3 FS on hda1, internal journal
[   24.785824] ACPI: AC Adapter [ACAD] (on-line)
[   24.957640] ACPI: Battery Slot [BAT1] (battery present)
[   24.975464] input: Power Button (FF) as /class/input/input6
[   24.975633] ACPI: Power Button (FF) [PWRF]
[   24.975694] input: Lid Switch as /class/input/input7
[   24.975720] ACPI: Lid Switch [LID]
[   24.975768] input: Power Button (CM) as /class/input/input8
[   24.975797] ACPI: Power Button (CM) [PWRB]
[   25.168688] Using specific hotkey driver
[   25.249422] No dock devices found.
[   25.288963] ibm_acpi: ec object not found
[   25.391752] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   25.417973] pcc_acpi: loading...
[   25.964903] usb-storage: device scan complete
[   25.969513] scsi 0:0:0:0: Direct-Access     ST316002 3A                    PQ: 0 ANSI: 0
[   26.027456] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[   26.029457] sda: Write Protect is off
[   26.029463] sda: Mode Sense: 33 00 00 00
[   26.029466] sda: assuming drive cache: write through
[   26.030429] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[   26.031300] sda: Write Protect is off
[   26.031303] sda: Mode Sense: 33 00 00 00
[   26.031305] sda: assuming drive cache: write through
[   26.031308]  sda: sda1
[   26.056583] sd 0:0:0:0: Attached scsi disk sda
[   26.079901] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   29.879108] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
[   30.761773] SoftMAC: Open Authentication completed with 00:0f:66:33:58:aa
[   32.592010] NET: Registered protocol family 17
[   32.821781] [drm] Initialized drm 1.1.0 20060810
[   32.835862] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 17
[   32.837030] [drm] Initialized radeon 1.25.0 20060524 on minor 0
[   33.364961] ppdev: user-space parallel port driver
[   33.958846] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[   33.958873] agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
[   33.958894] agpgart: Putting AGP V3 device at 0000:01:05.0 into 4x mode
[   34.338428] [drm] Setting GART location based on new memory map
[   34.338444] [drm] Loading R200 Microcode
[   34.338499] [drm] writeback test succeeded in 1 usecs
[   35.595166] apm: BIOS not found.
[   35.957963] NET: Registered protocol family 10
[   35.958123] lo: Disabled Privacy Extensions
[   36.149753] Bluetooth: Core ver 2.11
[   36.149860] NET: Registered protocol family 31
[   36.149863] Bluetooth: HCI device and connection manager initialized
[   36.149869] Bluetooth: HCI socket layer initialized
[   36.212119] Bluetooth: L2CAP ver 2.8
[   36.212127] Bluetooth: L2CAP socket layer initialized
[   36.381732] Bluetooth: RFCOMM socket layer initialized
[   36.381752] Bluetooth: RFCOMM TTY layer initialized
[   36.381755] Bluetooth: RFCOMM ver 1.8
[   46.422335] eth0: no IPv6 routers present
[   46.865937] eth1: no IPv6 routers present
[  173.224726] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  175.698320] eth1: no IPv6 routers present
[  185.254860] SoftMAC: Open Authentication completed with 00:0f:66:33:58:aa
[  238.943062] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  255.834402] eth1: no IPv6 routers present
[  274.991962] SoftMAC: Open Authentication completed with 00:0f:66:33:58:aa
[  675.050177] eth1: no IPv6 routers present
[  685.689976] SoftMAC: Open Authentication completed with 00:0f:66:33:58:aa
[ 2974.534519] SoftMAC: Authentication timed out with 00:0f:66:33:58:aa
[ 2993.389833] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2994.980167] eth1: no IPv6 routers present
[ 3053.455690] SoftMAC: Authentication timed out with 00:0f:66:33:58:aa

NicoA380 · Le 30/03/2007, à 14:58

Je vois pas grand chose qui parle de lecteur de carte

Peut-être ça "02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading Function (rev 01)" mais je ne m'y connais pas suffisamment pour t'assurer quoi que ce soit.

Peut-être y a-t-il des personnes plus éclairés sur le sujet ?

ghimli · Le 25/04/2007, à 10:23

Salut, va donc faire un tour sur ce tuto pris du forum anglophone :
http://forum.ubuntu-fr.org/viewtopic.ph … 91#p880591

serge benamou · Le 25/04/2007, à 12:23

bonjour

j'ai suivi le tuto pour feisty par conte pouvez vous me dire ce que signifie:

Ça devrait maintenant se lancer, faire des sauvegardes des anciens fichiers/modules, compiler, charger et décharger les modules.
Et une fois fini, ça devrait marcher !

je bloque la dessus

merci

ghimli · Le 25/04/2007, à 13:37

Ben il n'y a pas d'action à faire dans la phraseque tu me cites, c'est la description de ce que fait le script. Tu as dû avoir des lignes qui se sont affichées à l'écran. C'était pour un peu expliquer ce que ça signifiait. Normalement ça devrait marcher si tu as un lecteur Texas Instrument.

serge benamou · Le 25/04/2007, à 17:12

bon ben alors alors ça n'a pas marché... rien de plus dans mon dossier media... je suppose que c'est la que je verrais ma carte sd si c'etait bon non????

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 29/03/2007, à 22:23

lecteur de carte

#2 Le 29/03/2007, à 22:42

Re : lecteur de carte

#3 Le 29/03/2007, à 23:04

Re : lecteur de carte

#4 Le 30/03/2007, à 00:45

Re : lecteur de carte

#5 Le 30/03/2007, à 14:58

Re : lecteur de carte

#6 Le 25/04/2007, à 10:23

Re : lecteur de carte

#7 Le 25/04/2007, à 12:23

Re : lecteur de carte

#8 Le 25/04/2007, à 13:37

Re : lecteur de carte

#9 Le 25/04/2007, à 17:12

Re : lecteur de carte

Pied de page des forums