Ubuntu-fr

Andri

Breezy + ATI 9800Pro - Acceleration ne fonctionne pas.

Bonjour,

Cela fait une semaine que je tourne autour de plusieurs forums, que j'essaye des trucs conseillés par des gens dans les forums, mais je n'arrive toujours pas a faire marcher l'acceleration de ma carte ATI 9800Pro sous BREEZY. J'ai utillisé le dernier driver propriétaire d'ATI qui est le 8.16.20 - Mon noyau est le 2.6.12-8-386 (je ne trouve pas le linux-headers-2.16.20-8 sur internet- problème de depot????). Alors, si quelqu'un peut me conseiller, ce sera très apprécié.
Voila le résultat de #cat /var/log/Xorg.0.log | grep "fglrx":

(II) LoadModule: "fglrx"
(II) Loading /usr/X11R6/lib/modules/drivers/fglrx_drv.o
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found
(II) fglrx(0): pEnt->device->identifier=0x8212f08
(II) fglrx(0): === [R200PreInit] === begin, [s]
(II) fglrx(0): PCI bus 1 card 0 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "NoAccel" "no"
(**) fglrx(0): Option "NoDRI" "no"
(**) fglrx(0): Option "Capabilities" "0x00000000"
(**) fglrx(0): Option "CapabilitiesEx" "0x00000000"
(**) fglrx(0): Option "GammaCorrectionI" "0x06419064"
(**) fglrx(0): Option "GammaCorrectionII" "0x06419064"
(**) fglrx(0): Option "OpenGLOverlay" "off"
(**) fglrx(0): Option "VideoOverlay" "on"
(**) fglrx(0): Option "DesktopSetup" "(null)"
(**) fglrx(0): Option "ScreenOverlap" "0"
(**) fglrx(0): Option "UseInternalAGPGART" "yes"
(**) fglrx(0): Option "Stereo" "off"
(**) fglrx(0): Option "StereoSyncEnable" "1"
(**) fglrx(0): Option "UseFastTLS" "0"
(**) fglrx(0): Option "BlockSignalsOnLock" "on"
(**) fglrx(0): Option "ForceGenericCPU" "no"
(**) fglrx(0): Option "CenterMode" "off"
(**) fglrx(0): Option "FSAAScale" "1"
(**) fglrx(0): Option "FSAAEnable" "no"
(**) fglrx(0): Option "FSAADisableGamma" "no"
(**) fglrx(0): Option "FSAACustomizeMSPos" "no"
(**) fglrx(0): Option "FSAAMSPosX0" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY0" "0.000000"
(**) fglrx(0): Option "FSAAMSPosX1" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY1" "0.000000"
(**) fglrx(0): Option "FSAAMSPosX2" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY2" "0.000000"
(**) fglrx(0): Option "FSAAMSPosX3" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY3" "0.000000"
(**) fglrx(0): Option "FSAAMSPosX4" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY4" "0.000000"
(**) fglrx(0): Option "FSAAMSPosX5" "0.000000"
(**) fglrx(0): Option "FSAAMSPosY5" "0.000000"
(**) fglrx(0): Option "PseudoColorVisuals" "off"
(**) fglrx(0): Qbs disabled
(==) fglrx(0): FAST_SWAP disabled
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(**) fglrx(0): Gamma Correction for I is 0x06419064
(**) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(**) fglrx(0): Option "mtrr" "off"
(--) fglrx(0): Chipset: "RADEON 9800 PRO (R350 4E48)" (Chipset = 0x4e48)
(--) fglrx(0): (PciSubVendor = 0x1002, PciSubDevice = 0x0002)
(--) fglrx(0): board vendor info: original ATI graphics adapter
(--) fglrx(0): Linear framebuffer (phys) at 0xc0000000
(--) fglrx(0): MMIO registers at 0xcfef0000
(--) fglrx(0): ROM-BIOS at 0xcfec0000
(II) fglrx(0): VESA BIOS detected
(II) fglrx(0): VESA VBE Version 2.0
(II) fglrx(0): VESA VBE Total Mem: 131072 kB
(II) fglrx(0): VESA VBE OEM: ATI R350
(II) fglrx(0): VESA VBE OEM Software Rev: 1.0
(II) fglrx(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) fglrx(0): VESA VBE OEM Product: R350
(II) fglrx(0): VESA VBE OEM Product Rev: 01.00
(--) fglrx(0): VideoRAM: 131072 kByte, Type: DDR SGRAM / SDRAM
(II) fglrx(0): AGP card detected
(II) fglrx(0): board/chipset is supported by this driver (original ATI board)
(II) fglrx(0): Connected Display1: CRT on primary DAC
(II) fglrx(0): No EDID information available.
(WW) fglrx(0): Specified desktop setup not supported: 8
(II) fglrx(0): Primary Controller - CRT on primary DAC
(II) fglrx(0): Internal Desktop Setting: 0x00000004
(**) fglrx(0):  PseudoColor visuals disabled
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(**) fglrx(0): Center Mode is disabled
(==) fglrx(0): TMDS coherent mode is enabled
(II) fglrx(0): Total of 9 modes found for primary display.
(==) fglrx(0): DPI set to (75, 75)
(**) fglrx(0): NoAccel = NO
(==) fglrx(0): HPV inactive
(==) fglrx(0): FSAA enabled: NO
(**) fglrx(0): FSAA Gamma enabled
(**) fglrx(0): FSAA Multisample Position is fix
(**) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/X11R6/lib/modules/linux/libfglrxdrm.a
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
(II) fglrx(0): Depth moves disabled by default
(**) fglrx(0): Capabilities: 0x00000000
(**) fglrx(0): CapabilitiesEx: 0x00000000
(**) fglrx(0): cpuFlags: 0x4000001f
(**) fglrx(0): cpuSpeedMHz: 0x00000707
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(**) fglrx(0): using built in AGPGART module: yes
(**) fglrx(0): UseFastTLS=0
(**) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(II) fglrx(0): UMM Bus area:     0xc0501000 (size=0x07aff000)
(II) fglrx(0): UMM area:     0xc0501000 (size=0x07aff000)
(II) fglrx(0): driver needs X.org 6.8.x.y with x.y >= 0.0
(II) fglrx(0): detected X.org 6.8.2.0
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed!                  *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO)             *
(WW) fglrx(0): * no 3D acceleration available                *
(WW) fglrx(0): ********************************************* *
(II) fglrx(0): FBADPhys: 0xc0000000 FBMappedSize: 0x08000000
(II) fglrx(0): FBMM initialized for area (0,0)-(1024,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1024,768) (front color buffer - a ssumption)
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) fglrx(0): Using hardware cursor (scanline 768)
(II) fglrx(0): Largest offscreen area available: 1024 x 7419
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): Direct rendering disabled

Le log dit que Direct rendering et DRI ne fonctionnent pas.

Merci d'avance

Andri

Cakeman

Re : Breezy + ATI 9800Pro - Acceleration ne fonctionne pas.

Sous Hoary, ça marchait ? (moi y a pas de problème sous Hoary mais ça me fait peur de passer en breezy)

Andri

Re : Breezy + ATI 9800Pro - Acceleration ne fonctionne pas.

Cakeman,

En fait, c'est la premiere fois que j'utilise Ubuntu. J'ai toujours utilisé Fedora (+ redhat avant fedora). Alors, j'ai tout de suite installé Breezy. Breezy est très rapide, mais quelques problèmes pour installer des choses telles que la carte ATI.

Andri