#26 Le 22/07/2015, à 09:27
- Amekoa
Re : [Résolu] Probleme de redémarrage
Ah, j'avais oublié quelque chose d'important, je crois. Je n'ai pas retenu le texte exact mais durant le processus d'installation, s'il est demandé s'il faut continuer avec GPT ou Msdos, qu'est ce que je choisi ?
Hors ligne
#27 Le 22/07/2015, à 10:31
- Amekoa
Re : [Résolu] Probleme de redémarrage
J'ai fait l'installation d'Ubuntu jusqu'à son terme. J'ai redémarrer l'ordinateur comme recommandé mais il est revenu sur "Try ubuntu without installing". Dans Gparted, je vois bien que l'installation est bien présente avec les partitions suivantes:
Partitions Files system Size Used Unused Flags
/dev/sda1 Fat 32 512.00 MiB 4.36 MiB 507.64 MiB boot
/dev/sda2 Ext4 923.12 GiB 18.87 GiB 904.25 GiB
/dev/sda3 Linux-swap 7.89 GiB 4.00 KiB 7.89 GiB
Voilà la situation. Que puis-je faire ?
Hors ligne
#28 Le 22/07/2015, à 10:41
- Nasman
Re : [Résolu] Probleme de redémarrage
Enlever la clé usb ?
PC fixe sous Bionic 64 bits et portable avec Focal 64 bits
Hors ligne
#29 Le 22/07/2015, à 11:01
- Amekoa
Re : [Résolu] Probleme de redémarrage
Lorsque j'enlève la clé usb, ça ne démarre. Je remets la clé et je vais voir sur le disque dur avec Gparted et je vois que les partitions installées sont là.
Hors ligne
#30 Le 22/07/2015, à 11:07
- Nasman
Re : [Résolu] Probleme de redémarrage
Où as tu installé l'amorceur de démarrage (grub-pc) ? (si tu l'as installé)
PC fixe sous Bionic 64 bits et portable avec Focal 64 bits
Hors ligne
#31 Le 22/07/2015, à 11:11
- Amekoa
Re : [Résolu] Probleme de redémarrage
Je ne connais pas. Je n'ai rien installé. Un instant, lorsque j'installais ubuntu sur le disque dur externe, il y eut un message qui disait que le démarrage ou quelque chose du genre y sera installé. C'est de cela que tu parles ?
Hors ligne
#32 Le 22/07/2015, à 12:16
- malbo
Re : [Résolu] Probleme de redémarrage
Je t'ai dit ce qu'il fallait faire dans le post #24 : "Après installation, si tu n'arrives toujours pas à démarrer sur Ubuntu, je te prie de ne rien tenter avec Boot-repair ou autre chose (sinon, moi je n'arrive plus à savoir si c'est l'installateur de Ubuntu qui part en vrille ou si c'est toi qui brouille les cartes) : contente-toi de refaire un Boot-Info et de poster ici pour en donner l'URL"
Hors ligne
#33 Le 22/07/2015, à 12:40
- Amekoa
Re : [Résolu] Probleme de redémarrage
Voici le rapport Boot-Info
Hors ligne
#34 Le 23/07/2015, à 09:13
- Amekoa
Re : [Résolu] Probleme de redémarrage
Bonjour Malbo,
J'espère que tout va bien. Je n'ai pas eu de tes nouvelles et je m'inquiète. Tu peux me donner de tes nouvelles ?
Hors ligne
#35 Le 23/07/2015, à 10:21
- malbo
Re : [Résolu] Probleme de redémarrage
Ton Boot-Info ( http://paste.ubuntu.com/11919253/ ) est là :
Boot Info Script e7fc706 + Boot-Repair extra info [Boot-Info 9Feb2015]
============================= Boot Info Summary: ===============================
=> Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector
59086608 of the same hard drive for core.img. core.img is at this location
and looks for (,gpt2)/boot/grub.
=> Syslinux MBR (4.04 and higher) is installed in the MBR of /dev/sdb.
sda1: __________________________________________________________________________
File system: vfat
Boot sector type: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /EFI/ubuntu/MokManager.efi /EFI/ubuntu/grubx64.efi
/EFI/ubuntu/shimx64.efi
sda2: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Ubuntu 14.04.2 LTS
Boot files: /boot/grub/grub.cfg /etc/fstab
sda3: __________________________________________________________________________
File system: swap
Boot sector type: -
Boot sector info:
sdb1: __________________________________________________________________________
File system: vfat
Boot sector type: SYSLINUX 4.04 2011-04-18
Boot sector info: Syslinux looks at sector 2074272 of /dev/sdb1 for its
second stage. SYSLINUX is installed in the directory.
No errors found in the Boot Parameter Block.
Operating System:
Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg
/casper/vmlinuz.efi /EFI/BOOT/grubx64.efi /ldlinux.sys
============================ Drive/Partition Info: =============================
Drive: sda _____________________________________________________________________
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sda1 1 1,953,525,167 1,953,525,167 ee GPT
GUID Partition Table detected.
Partition Start Sector End Sector # of Sectors System
/dev/sda1 2,048 1,050,623 1,048,576 EFI System partition
/dev/sda2 1,050,624 1,936,969,727 1,935,919,104 Data partition (Linux)
/dev/sda3 1,936,969,728 1,953,523,711 16,553,984 Swap partition (Linux)
Drive: sdb _____________________________________________________________________
Disk /dev/sdb: 15.5 GB, 15512174592 bytes
32 heads, 63 sectors/track, 15028 cylinders, total 30297216 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sdb1 * 63 30,296,447 30,296,385 c W95 FAT32 (LBA)
"blkid" output: ________________________________________________________________
Device UUID TYPE LABEL
/dev/loop0 squashfs
/dev/sda1 6C5B-2C47 vfat
/dev/sda2 fa02904a-a8fb-4830-be02-69f24d5713e6 ext4
/dev/sda3 9a84dfb8-caa8-428c-8097-020dc9574892 swap
/dev/sdb1 EE98-593C vfat LEOKOK
========================= "ls -l /dev/disk/by-id" output: ======================
total 0
lrwxrwxrwx 1 root root 9 Jul 22 10:34 ata-ST1000DM003-1CH162_Z1D9GH5C -> ../../sda
lrwxrwxrwx 1 root root 10 Jul 22 08:59 ata-ST1000DM003-1CH162_Z1D9GH5C-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 Jul 22 08:58 ata-ST1000DM003-1CH162_Z1D9GH5C-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Jul 22 08:58 ata-ST1000DM003-1CH162_Z1D9GH5C-part3 -> ../../sda3
lrwxrwxrwx 1 root root 9 Jul 22 08:58 ata-hp_DVDRAM_GTA0N_B4ARQP2049516 -> ../../sr0
lrwxrwxrwx 1 root root 9 Jul 22 10:34 usb-TOSHIBA_TransMemory_3C7C152B794ECD70934891A8-0:0 -> ../../sdb
lrwxrwxrwx 1 root root 10 Jul 22 08:59 usb-TOSHIBA_TransMemory_3C7C152B794ECD70934891A8-0:0-part1 -> ../../sdb1
lrwxrwxrwx 1 root root 9 Jul 22 10:34 wwn-0x5000c50065f8c11f -> ../../sda
lrwxrwxrwx 1 root root 10 Jul 22 08:59 wwn-0x5000c50065f8c11f-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 Jul 22 08:58 wwn-0x5000c50065f8c11f-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Jul 22 08:58 wwn-0x5000c50065f8c11f-part3 -> ../../sda3
lrwxrwxrwx 1 root root 9 Jul 22 08:58 wwn-0x5001480000000000 -> ../../sr0
================================ Mount points: =================================
Device Mount_Point Type Options
/dev/loop0 /rofs squashfs (ro,noatime)
/dev/sdb1 /cdrom vfat (ro,noatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
=========================== sda2/boot/grub/grub.cfg: ===========================
--------------------------------------------------------------------------------
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
set have_grubenv=true
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}
function recordfail {
set recordfail=1
if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi
}
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
}
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=fr_FR
insmod gettext
fi
terminal_output gfxterm
if [ "${recordfail}" = 1 ] ; then
set timeout=30
else
if [ x$feature_timeout_style = xy ] ; then
set timeout_style=hidden
set timeout=0
# Fallback hidden-timeout code in case the timeout_style feature is
# unavailable.
elif sleep --interruptible 0 ; then
set timeout=0
fi
fi
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
if background_color 44,0,30,0; then
clear
fi
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/10_linux ###
function gfxmode {
set gfxpayload="${1}"
if [ "${1}" = "keep" ]; then
set vt_handoff=vt.handoff=7
else
set vt_handoff=
fi
}
if [ "${recordfail}" != 1 ]; then
if [ -e ${prefix}/gfxblacklist.txt ]; then
if hwmatch ${prefix}/gfxblacklist.txt 3; then
if [ ${match} = 0 ]; then
set linux_gfx_mode=keep
else
set linux_gfx_mode=text
fi
else
set linux_gfx_mode=text
fi
else
set linux_gfx_mode=keep
fi
else
set linux_gfx_mode=text
fi
export linux_gfx_mode
menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-fa02904a-a8fb-4830-be02-69f24d5713e6' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
linux /boot/vmlinuz-3.16.0-43-generic.efi.signed root=UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 ro quiet splash $vt_handoff
initrd /boot/initrd.img-3.16.0-43-generic
}
submenu 'Options avancées pour Ubuntu' $menuentry_id_option 'gnulinux-advanced-fa02904a-a8fb-4830-be02-69f24d5713e6' {
menuentry 'Ubuntu, avec Linux 3.16.0-43-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-43-generic-advanced-fa02904a-a8fb-4830-be02-69f24d5713e6' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
echo 'Chargement de Linux 3.16.0-43-generic…'
linux /boot/vmlinuz-3.16.0-43-generic.efi.signed root=UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 ro quiet splash $vt_handoff
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-43-generic
}
menuentry 'Ubuntu, with Linux 3.16.0-43-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-43-generic-recovery-fa02904a-a8fb-4830-be02-69f24d5713e6' {
recordfail
load_video
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
echo 'Chargement de Linux 3.16.0-43-generic…'
linux /boot/vmlinuz-3.16.0-43-generic.efi.signed root=UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 ro recovery nomodeset
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-43-generic
}
menuentry 'Ubuntu, avec Linux 3.16.0-30-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-30-generic-advanced-fa02904a-a8fb-4830-be02-69f24d5713e6' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
echo 'Chargement de Linux 3.16.0-30-generic…'
linux /boot/vmlinuz-3.16.0-30-generic root=UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 ro quiet splash $vt_handoff
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-30-generic
}
menuentry 'Ubuntu, with Linux 3.16.0-30-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-30-generic-recovery-fa02904a-a8fb-4830-be02-69f24d5713e6' {
recordfail
load_video
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 fa02904a-a8fb-4830-be02-69f24d5713e6
else
search --no-floppy --fs-uuid --set=root fa02904a-a8fb-4830-be02-69f24d5713e6
fi
echo 'Chargement de Linux 3.16.0-30-generic…'
linux /boot/vmlinuz-3.16.0-30-generic root=UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 ro recovery nomodeset
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-30-generic
}
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/20_memtest86+ ###
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/30_uefi-firmware ###
menuentry 'System setup' $menuentry_id_option 'uefi-firmware' {
fwsetup
}
### END /etc/grub.d/30_uefi-firmware ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
--------------------------------------------------------------------------------
=============================== sda2/etc/fstab: ================================
--------------------------------------------------------------------------------
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda2 during installation
UUID=fa02904a-a8fb-4830-be02-69f24d5713e6 / ext4 errors=remount-ro 0 1
# /boot/efi was on /dev/sda1 during installation
UUID=6C5B-2C47 /boot/efi vfat defaults 0 1
# swap was on /dev/sda3 during installation
UUID=9a84dfb8-caa8-428c-8097-020dc9574892 none swap sw 0 0
--------------------------------------------------------------------------------
=========================== sdb1/boot/grub/grub.cfg: ===========================
--------------------------------------------------------------------------------
if loadfont /boot/grub/font.pf2 ; then
set gfxmode=auto
insmod efi_gop
insmod efi_uga
insmod gfxterm
terminal_output gfxterm
fi
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
menuentry "Try Ubuntu without installing" {
set gfxpayload=keep
linux /casper/vmlinuz.efi file=/cdrom/preseed/ubuntu.seed boot=casper quiet splash --
initrd /casper/initrd.lz
}
menuentry "Install Ubuntu" {
set gfxpayload=keep
linux /casper/vmlinuz.efi file=/cdrom/preseed/ubuntu.seed boot=casper only-ubiquity quiet splash --
initrd /casper/initrd.lz
}
menuentry "OEM install (for manufacturers)" {
set gfxpayload=keep
linux /casper/vmlinuz.efi file=/cdrom/preseed/ubuntu.seed boot=casper only-ubiquity quiet splash oem-config/enable=true --
initrd /casper/initrd.lz
}
menuentry "Check disc for defects" {
set gfxpayload=keep
linux /casper/vmlinuz.efi boot=casper integrity-check quiet splash --
initrd /casper/initrd.lz
}
--------------------------------------------------------------------------------
========================= sdb1/syslinux/syslinux.cfg: ==========================
--------------------------------------------------------------------------------
# D-I config version 2.0
include menu.cfg
default vesamenu.c32
prompt 0
timeout 50
ui gfxboot bootlogo
--------------------------------------------------------------------------------
============== sdb1: Version of COM32(R) files used by Syslinux: ===============
syslinux/chain.c32 : COM32R module (v4.xx)
syslinux/gfxboot.c32 : COM32R module (v4.xx)
syslinux/vesamenu.c32 : COM32R module (v4.xx)
=============================== StdErr Messages: ===============================
cat: write error: Broken pipe
File descriptor 9 (/proc/5147/mounts) leaked on lvs invocation. Parent PID 11134: bash
File descriptor 63 (pipe:[57873]) leaked on lvs invocation. Parent PID 11134: bash
No volume groups found
ADDITIONAL INFORMATION :
=================== log of boot-info 2015-07-22__10h34 ===================
boot-info version : 4ppa33
boot-sav version : 4ppa33
glade2script version : 3.2.2~ppa47~saucy
boot-sav-extra version : 4ppa33
boot-info is executed in live-session (Ubuntu 14.04.2 LTS, trusty, Ubuntu, x86_64)
CPU op-mode(s): 32-bit, 64-bit
BOOT_IMAGE=/casper/vmlinuz.efi file=/cdrom/preseed/ubuntu.seed boot=casper quiet splash --
ls: cannot access /home/usr/.config: No such file or directory
WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted.
=================== os-prober:
/dev/sda2:Ubuntu 14.04.2 LTS (14.04):Ubuntu:linux
=================== blkid:
/dev/loop0: TYPE="squashfs"
/dev/sda1: UUID="6C5B-2C47" TYPE="vfat"
/dev/sda2: UUID="fa02904a-a8fb-4830-be02-69f24d5713e6" TYPE="ext4"
/dev/sda3: UUID="9a84dfb8-caa8-428c-8097-020dc9574892" TYPE="swap"
/dev/sdb1: LABEL="LEOKOK" UUID="EE98-593C" TYPE="vfat"
1 disks with OS, 1 OS : 1 Linux, 0 MacOS, 0 Windows, 0 unknown type OS.
WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util sfdisk doesn't support GPT. Use GNU Parted.
WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted.
=================== sda2/etc/grub.d/ :
drwxr-xr-x 2 root root 4096 Jul 22 07:59 grub.d
total 76
-rwxr-xr-x 1 root root 9424 Jun 26 11:16 00_header
-rwxr-xr-x 1 root root 6058 May 8 2014 05_debian_theme
-rwxr-xr-x 1 root root 11608 May 15 2014 10_linux
-rwxr-xr-x 1 root root 10412 May 15 2014 20_linux_xen
-rwxr-xr-x 1 root root 1992 Mar 12 2014 20_memtest86+
-rwxr-xr-x 1 root root 11692 May 15 2014 30_os-prober
-rwxr-xr-x 1 root root 1416 May 15 2014 30_uefi-firmware
-rwxr-xr-x 1 root root 214 May 15 2014 40_custom
-rwxr-xr-x 1 root root 216 May 15 2014 41_custom
-rw-r--r-- 1 root root 483 May 15 2014 README
=================== sda2/etc/default/grub :
# If you change this file, run 'update-grub' afterwards to update
# /boot/grub/grub.cfg.
# For full documentation of the options in this file, see:
# info -f grub -n 'Simple configuration'
GRUB_DEFAULT=0
GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=10
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX=""
# Uncomment to enable BadRAM filtering, modify to suit your needs
# This works with Linux (no patch required) and with any kernel that obtains
# the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
#GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef"
# Uncomment to disable graphical terminal (grub-pc only)
#GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480
# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
#GRUB_DISABLE_RECOVERY="true"
# Uncomment to get a beep at grub start
#GRUB_INIT_TUNE="480 440 1"
/boot/efi detected in the fstab of sda2: UUID=6C5B-2C47 (sda1)
=================== efibootmgr -v
BootCurrent: 0007
Timeout: 0 seconds
BootOrder: 0001,0002,0007,0003,0004,0005,0006,0000
Boot0000* ubuntu Vendor(99e275e7-75a0-4b37-a2e6-c5385e6c00cb,)
Boot0001* USB Floppy/CD Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0500000001)..BO
Boot0002* USB Hard Drive Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0200000001)..BO
Boot0003* UEFI: IPv4 Realtek PCIe GBE Family Controller ACPI(a0341d0,0)PCI(1c,7)PCI(0,0)MAC(0025ab423e61,0)IPv4(0.0.0.0:0<->0.0.0.0:0,0, 0..BO
Boot0004* UEFI: IPv6 Realtek PCIe GBE Family Controller ACPI(a0341d0,0)PCI(1c,7)PCI(0,0)MAC(0025ab423e61,0)030d3c000000000000000000000000000000000000000000000000000000000000000000000000000000004000000000000000000000000000000000..BO
Boot0005 USB Floppy/CD Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0500000000)..BO
Boot0006 Hard Drive Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0200000000)..BO
Boot0007* UEFI: TOSHIBA TransMemory 1.00 ACPI(a0341d0,0)PCI(1d,0)USB(1,0)USB(2,0)HD(1,3f,1ce4941,00065962)..BO
=================== UEFI/Legacy mode:
BIOS is EFI-compatible, and is setup in EFI-mode for this live-session.
SecureBoot enabled.
=================== PARTITIONS & DISKS:
sda1 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, is-correct-EFI, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, not-far, /mnt/boot-sav/sda1.
sda2 : sda, not-sepboot, grubenv-ok grub2, signed grub-efi , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-has-goodEFI, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, /mnt/boot-sav/sda2.
sda : GPT, no-BIOS_boot, has-correctEFI, not-usb, has-os, 2048 sectors * 512 bytes
=================== parted -l:
Model: ATA ST1000DM003-1CH1 (scsi)
Disk /dev/sda: 1000GB
Sector size (logical/physical): 512B/4096B
Partition Table: gpt
Number Start End Size File system Name Flags
1 1049kB 538MB 537MB fat32 boot
2 538MB 992GB 991GB ext4
3 992GB 1000GB 8476MB linux-swap(v1)
Model: TOSHIBA TransMemory (scsi)
Disk /dev/sdb: 15.5GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start End Size Type File system Flags
1 32.3kB 15.5GB 15.5GB primary fat32 boot, lba
=================== parted -lm:
BYT;
/dev/sda:1000GB:scsi:512:4096:gpt:ATA ST1000DM003-1CH1;
1:1049kB:538MB:537MB:fat32::boot;
2:538MB:992GB:991GB:ext4::;
3:992GB:1000GB:8476MB:linux-swap(v1)::;
BYT;
/dev/sdb:15.5GB:scsi:512:512:msdos:TOSHIBA TransMemory;
1:32.3kB:15.5GB:15.5GB:fat32::boot, lba;
=================== lsblk:
KNAME TYPE FSTYPE SIZE LABEL MODEL UUID
sda disk 931.5G ST1000DM0
sda1 part vfat 512M 6C5B-2C47
sda2 part ext4 923.1G fa02904a-a8fb-4830-be02-69f24d5713e6
sda3 part swap 7.9G 9a84dfb8-caa8-428c-8097-020dc9574892
sdb disk 14.5G TransMemo
sdb1 part vfat 14.5G LEOKOK EE98-593C
sr0 rom 1024M DVDRAM GT
loop0 loop squashfs 953M
KNAME ROTA RO RM STATE MOUNTPOINT
sda 1 0 0 running
sda1 1 0 0 /mnt/boot-sav/sda1
sda2 1 0 0 /mnt/boot-sav/sda2
sda3 1 0 0 [SWAP]
sdb 1 0 1 running
sdb1 1 0 1 /cdrom
sr0 1 0 1 running
loop0 1 1 0 /rofs
=================== mount:
/cow on / type overlayfs (rw)
proc on /proc type proc (rw,noexec,nosuid,nodev)
sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
udev on /dev type devtmpfs (rw,mode=0755)
devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620)
tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755)
/dev/sdb1 on /cdrom type vfat (ro,noatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/loop0 on /rofs type squashfs (ro,noatime)
none on /sys/fs/cgroup type tmpfs (rw)
none on /sys/fs/fuse/connections type fusectl (rw)
none on /sys/kernel/debug type debugfs (rw)
none on /sys/kernel/security type securityfs (rw)
none on /sys/firmware/efi/efivars type efivarfs (rw)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev)
none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880)
none on /run/shm type tmpfs (rw,nosuid,nodev)
none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755)
none on /sys/fs/pstore type pstore (rw)
systemd on /sys/fs/cgroup/systemd type cgroup (rw,noexec,nosuid,nodev,none,name=systemd)
gvfsd-fuse on /run/user/999/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=ubuntu)
/dev/sda1 on /mnt/boot-sav/sda1 type vfat (rw)
/dev/sda2 on /mnt/boot-sav/sda2 type ext4 (rw)
=================== ls:
/sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda3 size slaves stat subsystem trace uevent
/sys/block/sdb (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sdb1 size slaves stat subsystem trace uevent
/sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent
/dev (filtered): autofs block bsg btrfs-control bus cdrom char console core cpu cpu_dma_latency cuse disk dri ecryptfs fb0 fd full fuse hidraw0 hidraw1 hidraw2 hidraw3 hidraw4 hidraw5 hpet input kmsg log mapper mcelog media0 mei mem net network_latency network_throughput null port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda3 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sr0 stderr stdin stdout uhid uinput urandom usb v4l vfio vga_arbiter vhci vhost-net video0 zero
ls /dev/mapper: control
=================== hexdump -n512 -C /dev/sda1
00000000 eb 58 90 6d 6b 66 73 2e 66 61 74 00 02 08 20 00 |.X.mkfs.fat... .|
00000010 02 00 00 00 00 f8 00 00 3f 00 ff 00 00 08 00 00 |........?.......|
00000020 00 00 10 00 fe 03 00 00 00 00 00 00 02 00 00 00 |................|
00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000040 80 01 29 47 2c 5b 6c 4e 4f 20 4e 41 4d 45 20 20 |..)G,[lNO NAME |
00000050 20 20 46 41 54 33 32 20 20 20 0e 1f be 77 7c ac | FAT32 ...w|.|
00000060 22 c0 74 0b 56 b4 0e bb 07 00 cd 10 5e eb f0 32 |".t.V.......^..2|
00000070 e4 cd 16 cd 19 eb fe 54 68 69 73 20 69 73 20 6e |.......This is n|
00000080 6f 74 20 61 20 62 6f 6f 74 61 62 6c 65 20 64 69 |ot a bootable di|
00000090 73 6b 2e 20 20 50 6c 65 61 73 65 20 69 6e 73 65 |sk. Please inse|
000000a0 72 74 20 61 20 62 6f 6f 74 61 62 6c 65 20 66 6c |rt a bootable fl|
000000b0 6f 70 70 79 20 61 6e 64 0d 0a 70 72 65 73 73 20 |oppy and..press |
000000c0 61 6e 79 20 6b 65 79 20 74 6f 20 74 72 79 20 61 |any key to try a|
000000d0 67 61 69 6e 20 2e 2e 2e 20 0d 0a 00 00 00 00 00 |gain ... .......|
000000e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
*
000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.|
00000200
WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted.
=================== df -Th:
Filesystem Type Size Used Avail Use% Mounted on
/cow overlayfs 3.9G 104M 3.8G 3% /
udev devtmpfs 3.9G 12K 3.9G 1% /dev
tmpfs tmpfs 788M 1.4M 787M 1% /run
/dev/sdb1 vfat 15G 997M 14G 7% /cdrom
/dev/loop0 squashfs 953M 953M 0 100% /rofs
none tmpfs 4.0K 0 4.0K 0% /sys/fs/cgroup
tmpfs tmpfs 3.9G 1.2M 3.9G 1% /tmp
none tmpfs 5.0M 0 5.0M 0% /run/lock
none tmpfs 3.9G 80K 3.9G 1% /run/shm
none tmpfs 100M 68K 100M 1% /run/user
/dev/sda1 vfat 511M 3.4M 508M 1% /mnt/boot-sav/sda1
/dev/sda2 ext4 909G 4.3G 859G 1% /mnt/boot-sav/sda2
=================== fdisk -l:
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk identifier: 0xfa8228ea
Device Boot Start End Blocks Id System
/dev/sda1 1 1953525167 976762583+ ee GPT
Partition 1 does not start on physical sector boundary.
Disk /dev/sdb: 15.5 GB, 15512174592 bytes
32 heads, 63 sectors/track, 15028 cylinders, total 30297216 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00065962
Device Boot Start End Blocks Id System
/dev/sdb1 * 63 30296447 15148192+ c W95 FAT32 (LBA)
=================== Suggested repair
The default repair of the Boot-Repair utility would reinstall the grub-efi-amd64-signed of sda2, using the following options: sda1/boot/efi,
Additional repair would be performed: unhide-bootmenu-10s use-standard-efi-file rename-ms-efi
=================== User settings
The settings chosen by the user will not act on the boot.
Pour moi l'installation est parfaite sauf que ton système UEFI (ton "Bios") est verouillé comme on peut voir là :
=================== efibootmgr -v
BootCurrent: 0007
Timeout: 0 seconds
BootOrder: 0001,0002,0007,0003,0004,0005,0006,0000
Boot0000* ubuntu Vendor(99e275e7-75a0-4b37-a2e6-c5385e6c00cb,)
Boot0001* USB Floppy/CD Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0500000001)..BO
Boot0002* USB Hard Drive Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0200000001)..BO
Boot0003* UEFI: IPv4 Realtek PCIe GBE Family Controller ACPI(a0341d0,0)PCI(1c,7)PCI(0,0)MAC(0025ab423e61,0)IPv4(0.0.0.0:0<->0.0.0.0:0,0, 0..BO
Boot0004* UEFI: IPv6 Realtek PCIe GBE Family Controller ACPI(a0341d0,0)PCI(1c,7)PCI(0,0)MAC(0025ab423e61,0)030d3c000000000000000000000000000000000000000000000000000000000000000000000000000000004000000000000000000000000000000000..BO
Boot0005 USB Floppy/CD Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0500000000)..BO
Boot0006 Hard Drive Vendor(b6fef66f-1495-4584-a836-3492d1984a8d,0200000000)..BO
Boot0007* UEFI: TOSHIBA TransMemory 1.00 ACPI(a0341d0,0)PCI(1d,0)USB(1,0)USB(2,0)HD(1,3f,1ce4941,00065962)..BO
C'est à dire que dans ton "Bios", il y a bien une entrée pour "ubuntu" (Boot0000) : elle a bien été créée par l'installateur de Ubuntu mais elle n'est pas fonctionnelle(*).
Je ne sais pas te proposer quelque chose de sérieux pour sortir de là. C'est le cœur serré que je te propose aujourd'hui de réinstaller Windows là-dedans. Si quelqu'un a une meilleure idée...
(*)Vendor(99e275e7-75a0-4b37-a2e6-c5385e6c00cb,) signifie que cette entrée est illisible par ton Bios. J'en parle dans ce fil : "[Essai] Entrées UEFI corrompues " Vendor "
Dernière modification par malbo (Le 23/07/2015, à 10:27)
Hors ligne
#36 Le 23/07/2015, à 11:45
- Amekoa
Re : [Résolu] Probleme de redémarrage
Je ne m'y connais pas trop. C'est que je ne veux pas revenir à Windows sur cet ordinateur. Si je change de disque dur, puis-je installer Ubuntu sans problème d'amorçage ? J'ai un portable en duo boot Windows 7 et Ubuntu 14.04 LTS qui fonctionne sans problème. J'ai voulu tester le HP All-in-one avec Ubuntu avant d'y installer Ubuntu à 100%. Alors si je change de disque dur, est-ce possible de résoudre le problème d'amorçage ? Si oui, comment procéder ?
Excuse-moi de t'importuner avec mes problèmes ?
Hors ligne
#37 Le 23/07/2015, à 12:13
- malbo
Re : [Résolu] Probleme de redémarrage
Si tu es décidé à ne pas revenir à Windows sur cet ordinateur, il faudrait faire l'installation de Ubuntu en mode non-EFI suivant ce que j'explique dans ce post : [Essais] Install de Ubuntu en mode non-EFI dans un préinstallé Win8
En fait, tu peux te contenter du résumé que j'ai fait en bas du post mais que je colle ici par commodité :
EDIT : la procédure peut se formaliser ainsi :
1) dans l'UEFI (dans le nouveau "Bios"), désactiver "Fast Boot" (le cas échéant), désactiver "Secure Boot" et passer le "Boot Mode" sur "Legacy" au lieu de "UEFI" (chez certains fabricants, il faut activer "Launch CSM" qui est l'équivalent de "Legacy")
2) lancer l'installation de Ubuntu. A l'étape 3, sélectionner le mode automatique qui écrase tout ce qui existe sur le disque dur pour installer Ubuntu.
Toi tu as "Secure Boot" qui est actuellement activé et il conviendra donc que tu le désactives (pour cela, des indications sont données dans la doc). Ensuite seulement, tu pourras parvenir à activer le mode Legacy . Avec un Bios en anglais, ça donne ce que tu peux voir dans ce post (la photo). A savoir :
Legacy Support : Enabled
Secure Boot : Disabled
Voilà à quoi tu dois parvenir dans ton Bios pour être en mesure de faire une installation en mode non-EFI. Sauf que dans ton cas, ça doit être un Bios en espagnol...
Dernière modification par malbo (Le 23/07/2015, à 12:14)
Hors ligne
#38 Le 23/07/2015, à 13:02
- Amekoa
Re : [Résolu] Probleme de redémarrage
J'ai procédé comme indiqué et j'ai reçu un message qui finit par :
ERROR: No boot disk has been detected or the disk has falled.
Je continue la procédure malgré tout ?
Hors ligne
#39 Le 23/07/2015, à 16:25
- malbo
Re : [Résolu] Probleme de redémarrage
Es-tu parvenu à désactiver "Secure Boot" et à activer "Legacy Support" dans ton "Bios" comme j'ai indiqué dans le post #37 ?
Si oui, je te prie de prendre une photo (ou plusieurs) de ton Bios pour que je puisse vérifier la chose. Pour poster des photos, je te prie de suivre les indications données ici : 4.4 Insérer une image
Hors ligne
#40 Le 23/07/2015, à 17:29
- Amekoa
Re : [Résolu] Probleme de redémarrage
Désolé Malbo, je n'ai pas pu attendre. Après deux revérifications de la mise en application de tes indications, constatant qu'il n'y a pas eu d'erreurs possibles de ma part dans cette mise en application, je me suis dit que le message d'erreur est logique puisque l'amorçage était l'unique problème et que seule l'installation pourrait fournir les éléments de solution pour le démarrage du S.O de l'ordinateur. Et effectivement, après l'installation d'Ubuntu 14.14 LTS, l'ordinateur a redémarré sans problème, le message d'erreur a disparu et Ubuntu fonctionne bien. Actuellement je suis en train d'installer les logicielles dont j'ai besoin. Si je rencontre un problème, je t'en informerai. Merci pour toute ton aide. Ah, je possède un Adobe Master 2003 que j'utilise jusqu'à présent. Je ne sais pas si Adobe est accepté par Ubuntu. Si oui, comment procéder ? Encore une fois, merci infiniment pour ton aide si précieuse.
Hors ligne
#41 Le 23/07/2015, à 18:02
- malbo
Re : [Résolu] Probleme de redémarrage
J'aimerais bien tirer une leçon de tout ça mais là il me manque des morceaux. Pour que je puisse comprendre, je te prie de démarrer une session sur ton Ubuntu fraîchement installé et faire un Boot-Info depuis cette session. Tu donneras l'URL du Boot-Info dans ta réponse.
Hors ligne
#42 Le 23/07/2015, à 18:41
- Amekoa
Re : [Résolu] Probleme de redémarrage
Voici le rapport boot-info
http://paste.ubuntu.com/11925956/
S'il te plaît, la réponse à ma question concernant l'installation de Adobe Master 2003. Si tu peux aussi me faire profiter des enseignements que tu tireras de tout, ça m'aidera dans la connaissance de Linux. C'est la raison essentiellement de mon choix de Ubuntu. A bientôt
Hors ligne
#43 Le 24/07/2015, à 06:14
- malbo
Re : [Résolu] Probleme de redémarrage
Ton Boot-Info est là :
Boot Info Script e7fc706 + Boot-Repair extra info [Boot-Info 9Feb2015]
============================= Boot Info Summary: ===============================
=> Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 1 of
the same hard drive for core.img. core.img is at this location and looks
for (,msdos1)/boot/grub.
sda1: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Ubuntu 14.04.2 LTS
Boot files: /boot/grub/grub.cfg /etc/fstab
/boot/grub/i386-pc/core.img
sda2: __________________________________________________________________________
File system: Extended Partition
Boot sector type: -
Boot sector info:
sda5: __________________________________________________________________________
File system: swap
Boot sector type: -
Boot sector info:
============================ Drive/Partition Info: =============================
Drive: sda _____________________________________________________________________
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sda1 * 2,048 1,936,971,775 1,936,969,728 83 Linux
/dev/sda2 1,936,973,822 1,953,523,711 16,549,890 5 Extended
/dev/sda5 1,936,973,824 1,953,523,711 16,549,888 82 Linux swap / Solaris
"blkid" output: ________________________________________________________________
Device UUID TYPE LABEL
/dev/sda1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d ext4
/dev/sda5 2c628754-0218-4f26-bc25-c85ae401730f swap
========================= "ls -l /dev/disk/by-id" output: ======================
total 0
lrwxrwxrwx 1 root root 9 Jul 23 18:37 ata-ST1000DM003-1CH162_Z1D9GH5C -> ../../sda
lrwxrwxrwx 1 root root 10 Jul 23 16:01 ata-ST1000DM003-1CH162_Z1D9GH5C-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 Jul 23 17:36 ata-ST1000DM003-1CH162_Z1D9GH5C-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Jul 23 16:01 ata-ST1000DM003-1CH162_Z1D9GH5C-part5 -> ../../sda5
lrwxrwxrwx 1 root root 9 Jul 23 16:01 ata-hp_DVDRAM_GTA0N_B4ARQP2049516 -> ../../sr0
lrwxrwxrwx 1 root root 9 Jul 23 18:37 wwn-0x5000c50065f8c11f -> ../../sda
lrwxrwxrwx 1 root root 10 Jul 23 16:01 wwn-0x5000c50065f8c11f-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 Jul 23 17:36 wwn-0x5000c50065f8c11f-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 Jul 23 16:01 wwn-0x5000c50065f8c11f-part5 -> ../../sda5
lrwxrwxrwx 1 root root 9 Jul 23 16:01 wwn-0x5001480000000000 -> ../../sr0
================================ Mount points: =================================
Device Mount_Point Type Options
/dev/sda1 / ext4 (rw,errors=remount-ro)
=========================== sda1/boot/grub/grub.cfg: ===========================
--------------------------------------------------------------------------------
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
set have_grubenv=true
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}
function recordfail {
set recordfail=1
if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi
}
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
}
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=fr_FR
insmod gettext
fi
terminal_output gfxterm
if [ "${recordfail}" = 1 ] ; then
set timeout=30
else
if [ x$feature_timeout_style = xy ] ; then
set timeout_style=hidden
set timeout=0
# Fallback hidden-timeout code in case the timeout_style feature is
# unavailable.
elif sleep --interruptible 0 ; then
set timeout=0
fi
fi
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/05_debian_theme ###
set menu_color_normal=white/black
set menu_color_highlight=black/light-gray
if background_color 44,0,30,0; then
clear
fi
### END /etc/grub.d/05_debian_theme ###
### BEGIN /etc/grub.d/10_linux ###
function gfxmode {
set gfxpayload="${1}"
if [ "${1}" = "keep" ]; then
set vt_handoff=vt.handoff=7
else
set vt_handoff=
fi
}
if [ "${recordfail}" != 1 ]; then
if [ -e ${prefix}/gfxblacklist.txt ]; then
if hwmatch ${prefix}/gfxblacklist.txt 3; then
if [ ${match} = 0 ]; then
set linux_gfx_mode=keep
else
set linux_gfx_mode=text
fi
else
set linux_gfx_mode=text
fi
else
set linux_gfx_mode=keep
fi
else
set linux_gfx_mode=text
fi
export linux_gfx_mode
menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
linux /boot/vmlinuz-3.16.0-44-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro quiet splash $vt_handoff
initrd /boot/initrd.img-3.16.0-44-generic
}
submenu 'Options avancées pour Ubuntu' $menuentry_id_option 'gnulinux-advanced-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
menuentry 'Ubuntu, avec Linux 3.16.0-44-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-44-generic-advanced-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
echo 'Chargement de Linux 3.16.0-44-generic…'
linux /boot/vmlinuz-3.16.0-44-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro quiet splash $vt_handoff
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-44-generic
}
menuentry 'Ubuntu, with Linux 3.16.0-44-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-44-generic-recovery-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
recordfail
load_video
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
echo 'Chargement de Linux 3.16.0-44-generic…'
linux /boot/vmlinuz-3.16.0-44-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro recovery nomodeset
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-44-generic
}
menuentry 'Ubuntu, avec Linux 3.16.0-30-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-30-generic-advanced-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
recordfail
load_video
gfxmode $linux_gfx_mode
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
echo 'Chargement de Linux 3.16.0-30-generic…'
linux /boot/vmlinuz-3.16.0-30-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro quiet splash $vt_handoff
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-30-generic
}
menuentry 'Ubuntu, with Linux 3.16.0-30-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-30-generic-recovery-68aadb77-1a21-44fc-89b4-3cd0bd78b14d' {
recordfail
load_video
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
echo 'Chargement de Linux 3.16.0-30-generic…'
linux /boot/vmlinuz-3.16.0-30-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro recovery nomodeset
echo 'Chargement du disque mémoire initial…'
initrd /boot/initrd.img-3.16.0-30-generic
}
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/20_memtest86+ ###
menuentry 'Memory test (memtest86+)' {
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
knetbsd /boot/memtest86+.elf
}
menuentry 'Memory test (memtest86+, serial console 115200)' {
insmod part_msdos
insmod ext2
set root='hd0,msdos1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
else
search --no-floppy --fs-uuid --set=root 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
fi
linux16 /boot/memtest86+.bin console=ttyS0,115200n8
}
### END /etc/grub.d/20_memtest86+ ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/30_uefi-firmware ###
### END /etc/grub.d/30_uefi-firmware ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
--------------------------------------------------------------------------------
=============================== sda1/etc/fstab: ================================
--------------------------------------------------------------------------------
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda1 during installation
UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d / ext4 errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=2c628754-0218-4f26-bc25-c85ae401730f none swap sw 0 0
--------------------------------------------------------------------------------
=============================== StdErr Messages: ===============================
cat: write error: Broken pipe
ADDITIONAL INFORMATION :
=================== log of boot-info 2015-07-23__18h37 ===================
boot-info version : 4ppa33
boot-sav version : 4ppa33
glade2script version : 3.2.2~ppa47~saucy
boot-sav-extra version : 4ppa33
boot-info is executed in installed-session (Ubuntu 14.04.2 LTS, trusty, Ubuntu, x86_64)
CPU op-mode(s): 32-bit, 64-bit
BOOT_IMAGE=/boot/vmlinuz-3.16.0-44-generic root=UUID=68aadb77-1a21-44fc-89b4-3cd0bd78b14d ro quiet splash vt.handoff=7
=================== os-prober:
/dev/sda1:L'OS actuellement utilisé - Ubuntu 14.04.2 LTS CurrentSession:linux
=================== blkid:
/dev/sda1: UUID="68aadb77-1a21-44fc-89b4-3cd0bd78b14d" TYPE="ext4"
/dev/sda5: UUID="2c628754-0218-4f26-bc25-c85ae401730f" TYPE="swap"
1 disks with OS, 1 OS : 1 Linux, 0 MacOS, 0 Windows, 0 unknown type OS.
Avertissement : la partition étendue ne commence pas sur une frontière de
cylindres. DOS et Linux interpréteront les contenus différemment.
=================== /etc/grub.d/ :
drwxr-xr-x 2 root root 4096 juil. 23 15:58 grub.d
total 76
-rwxr-xr-x 1 root root 9424 juin 26 13:16 00_header
-rwxr-xr-x 1 root root 6058 mai 8 2014 05_debian_theme
-rwxr-xr-x 1 root root 11608 mai 15 2014 10_linux
-rwxr-xr-x 1 root root 10412 mai 15 2014 20_linux_xen
-rwxr-xr-x 1 root root 1992 mars 12 2014 20_memtest86+
-rwxr-xr-x 1 root root 11692 mai 15 2014 30_os-prober
-rwxr-xr-x 1 root root 1416 mai 15 2014 30_uefi-firmware
-rwxr-xr-x 1 root root 214 mai 15 2014 40_custom
-rwxr-xr-x 1 root root 216 mai 15 2014 41_custom
-rw-r--r-- 1 root root 483 mai 15 2014 README
=================== /etc/default/grub :
# If you change this file, run 'update-grub' afterwards to update
# /boot/grub/grub.cfg.
# For full documentation of the options in this file, see:
# info -f grub -n 'Simple configuration'
GRUB_DEFAULT=0
GRUB_HIDDEN_TIMEOUT=0
GRUB_HIDDEN_TIMEOUT_QUIET=true
GRUB_TIMEOUT=10
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX=""
# Uncomment to enable BadRAM filtering, modify to suit your needs
# This works with Linux (no patch required) and with any kernel that obtains
# the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
#GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef"
# Uncomment to disable graphical terminal (grub-pc only)
#GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480
# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
#GRUB_DISABLE_RECOVERY="true"
# Uncomment to get a beep at grub start
#GRUB_INIT_TUNE="480 440 1"
=================== UEFI/Legacy mode:
This installed-session is not in EFI-mode.
SecureBoot disabled.
=================== PARTITIONS & DISKS:
sda1 : sda, not-sepboot, grubenv-ok grub2, grub-pc , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-without-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, .
sda : not-GPT, BIOSboot-not-needed, has-no-EFIpart, not-usb, has-os, 2048 sectors * 512 bytes
=================== parted -l:
Model: ATA ST1000DM003-1CH1 (scsi)
Disk /dev/sda: 1000GB
Sector size (logical/physical): 512B/4096B
Partition Table: msdos
Number Start End Size Type File system Flags
1 1049kB 992GB 992GB primary ext4 boot
2 992GB 1000GB 8474MB extended
5 992GB 1000GB 8474MB logical linux-swap(v1)
=================== parted -lm:
BYT;
/dev/sda:1000GB:scsi:512:4096:msdos:ATA ST1000DM003-1CH1;
1:1049kB:992GB:992GB:ext4::boot;
2:992GB:1000GB:8474MB:::;
5:992GB:1000GB:8474MB:linux-swap(v1)::;
=================== lsblk:
KNAME TYPE FSTYPE SIZE LABEL MODEL UUID
sda disk 931,5G ST1000DM003-
sda1 part ext4 923,6G 68aadb77-1a21-44fc-89b4-3cd0bd78b14d
sda2 part 1K
sda5 part swap 7,9G 2c628754-0218-4f26-bc25-c85ae401730f
sr0 rom 1024M DVDRAM GTA0N
KNAME ROTA RO RM STATE MOUNTPOINT
sda 1 0 0 running
sda1 1 0 0 /
sda2 1 0 0
sda5 1 0 0 [SWAP]
sr0 1 0 1 running
=================== mount:
/dev/sda1 on / type ext4 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
sysfs on /sys type sysfs (rw,noexec,nosuid,nodev)
none on /sys/fs/cgroup type tmpfs (rw)
none on /sys/fs/fuse/connections type fusectl (rw)
none on /sys/kernel/debug type debugfs (rw)
none on /sys/kernel/security type securityfs (rw)
udev on /dev type devtmpfs (rw,mode=0755)
devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620)
tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755)
none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880)
none on /run/shm type tmpfs (rw,nosuid,nodev)
none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755)
none on /sys/fs/pstore type pstore (rw)
systemd on /sys/fs/cgroup/systemd type cgroup (rw,noexec,nosuid,nodev,none,name=systemd)
gvfsd-fuse on /run/user/1000/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=ame)
=================== ls:
/sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda5 size slaves stat subsystem trace uevent
/sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent
/dev (filtered): autofs block bsg btrfs-control bus cdrom char console core cpu cpu_dma_latency cuse disk dri ecryptfs fb0 fd full fuse hidraw0 hidraw1 hidraw2 hidraw3 hidraw4 hidraw5 hpet input kmsg log mapper mcelog media0 mei mem net network_latency network_throughput null port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda5 sg0 sg1 shm snapshot snd sr0 stderr stdin stdout uhid uinput urandom usb v4l vfio vga_arbiter vhci vhost-net video0 zero
ls /dev/mapper: control
ls: impossible d'accéder à : Aucun fichier ou dossier de ce type
=================== df -Th:
Filesystem Type Size Used Avail Use% Mounted on
/dev/sda1 ext4 910G 5.4G 858G 1% /
none tmpfs 4.0K 0 4.0K 0% /sys/fs/cgroup
udev devtmpfs 3.9G 12K 3.9G 1% /dev
tmpfs tmpfs 788M 1.3M 787M 1% /run
none tmpfs 5.0M 0 5.0M 0% /run/lock
none tmpfs 3.9G 38M 3.9G 1% /run/shm
none tmpfs 100M 56K 100M 1% /run/user
=================== fdisk -l:
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk identifier: 0xfa8228ea
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 1936971775 968484864 83 Linux
/dev/sda2 1936973822 1953523711 8274945 5 Extended
Partition 2 does not start on physical sector boundary.
/dev/sda5 1936973824 1953523711 8274944 82 Linux swap / Solaris
=================== Suggested repair
The default repair of the Boot-Repair utility would reinstall the grub2 of sda1 into the MBR of sda.
Additional repair would be performed: unhide-bootmenu-10s
=================== Final advice in case of suggested repair
Les fichiers de démarrage de [L'OS actuellement utilisé - Ubuntu 14.04.2 LTS] sont loin du début du disque. Votre BIOS pourrait ne pas les détecter. Vous voudrez peut-être re-essayer après avoir créé une partition /boot (EXT4, >200MB, en début de disque). Cela peut être réalisé via des outils tels que gParted. Puis sélectionnez cette partition via l'option [Partition /boot séparée :] de [Boot-Repair]. (http://doc.ubuntu-fr.org/tutoriel/partition_boot)
=================== User settings
The settings chosen by the user will not act on the boot.
Tout semble parfait. Dans l'extrait suivant, c'est écrit clairement que tu as activé le mode Legacy (tu n'es pas en mode EFI) et que tu as désactivé "Secure Boot" :
=================== UEFI/Legacy mode:
This installed-session is not in EFI-mode.
SecureBoot disabled.
D'autre part, tu as bien fait une installation automatique de Ubuntu qui écrase tout (tu as choisis "Effacer le disque et installer Ubuntu" à l'étape "Type d'installation") ce qui fait que ta table de partition a été entièrement refaite à neuf comme prévu : elle est à présent du type MSDOS comme tu peux lire ici :
=================== parted -l:
Model: ATA ST1000DM003-1CH1 (scsi)
Disk /dev/sda: 1000GB
Sector size (logical/physical): 512B/4096B
Partition Table: msdos
Number Start End Size Type File system Flags
1 1049kB 992GB 992GB primary ext4 boot
2 992GB 1000GB 8474MB extended
5 992GB 1000GB 8474MB logical linux-swap(v1)
Alors qu'elle était précédemment du type GPT.
Tu as donc obtenu exactement ce que je te proposais dans le post #37 alors que la lecture de tes derniers posts m'inquiétait un peu et je craignais que tu aies pris un autre chemin.
Pour ta question sur Adobe Master 2003, je te prie de créer une nouvelle discussion dans la rubrique adaptée du forum.
EDIT : je viens d'ajouter ton modèle d'ordi HP Pavilion 22-h040es dans la Liste des portables « HP ».
Je te prie de modifier le titre de ton PREMIER message afin qu'il devienne :
[Résolu] Probleme de redemarrage
Dernière modification par malbo (Le 24/07/2015, à 07:16)
Hors ligne
#44 Le 24/07/2015, à 11:53
- Amekoa
Re : [Résolu] Probleme de redémarrage
malbo, merci infiniment pour tout.
Hors ligne
#45 Le 28/08/2015, à 12:26
- Amekoa
Re : [Résolu] Probleme de redémarrage
J'ai installé Ubuntu 14.04 LTS sur un disque dur externe Toshiba HDD. Que faire pour pouvoir l'utiliser sur un ordinaire de bureau All-in-One HP pavillon 22 sous Windows 8 prof. Merci d'avance.
Hors ligne
#46 Le 28/08/2015, à 12:37
- malbo
Re : [Résolu] Probleme de redémarrage
@Amekoa : le sujet de la présente discusion est clos. Pour ton problème du post #45, je te prie de créer une nouvelle discussion. Les indications pour le faire sont là : 4.1 Initier une nouvelle discussion
Hors ligne