Résolu Disque dur externe neuf non reconnu par ubuntu

hardouin48 · Le 31/08/2019, à 11:03

hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on  -d sat  -a /dev/sdb
[sudo] Mot de passe de hardouin : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error medium or hardware error (serious)

A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
hardouin@hardouin-Aspire-V3-372:~$

geole · Le 31/08/2019, à 11:05

sudo smartctl   -s   on  -d sat   -T  verypermissive  -a /dev/sdb

hardouin48 · Le 31/08/2019, à 11:09

hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on  -d sat   -T  verypermissive  -a /dev/sdb
[sudo] Mot de passe de hardouin : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error medium or hardware error (serious)

=== START OF INFORMATION SECTION ===
Device Model:     [No Information Found]
Serial Number:    [No Information Found]
Firmware Version: [No Information Found]
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   [No Information Found]
Local Time is:    Sat Aug 31 12:08:52 2019 CEST
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled.
                  Checking to be sure by trying SMART RETURN STATUS command.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enable failed: scsi error medium or hardware error (serious)

Read SMART Data failed: scsi error medium or hardware error (serious)


=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.

Read SMART Error Log failed: scsi error medium or hardware error (serious)

Read SMART Self-test Log failed: scsi error medium or hardware error (serious)

Selective Self-tests/Logging not supported

hardouin@hardouin-Aspire-V3-372:~$

hardouin48 · Le 31/08/2019, à 11:45

hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on  -d sat  -a /dev/sdb
[sudo] Mot de passe de hardouin : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error medium or hardware error (serious)

A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on   -d usbjmicron   -a /dev/sdb
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Smartctl open device: /dev/sdb [USB JMicron] failed: No device connected
hardouin@hardouin-Aspire-V3-372:~$

geole · Le 31/08/2019, à 11:47

Je mets la trace du premier incident

[ 1067.297461] usb 2-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 1067.318806] usb 2-1: New USB device found, idVendor=152d, idProduct=0578
[ 1067.318817] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1067.318823] usb 2-1: Product: USB to ATA/ATAPI Bridge
[ 1067.318829] usb 2-1: Manufacturer: JMicron
[ 1067.318835] usb 2-1: SerialNumber: 0123456789ABCDEF
[ 1067.343256] usbcore: registered new interface driver usb-storage
[ 1067.347268] scsi host3: uas
[ 1067.347390] usbcore: registered new interface driver uas
[ 1067.347770] scsi 3:0:0:0: Direct-Access     JMicron  Generic          0508 PQ: 0 ANSI: 6
[ 1067.348573] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 1068.867622] sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1068.867632] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[ 1068.867824] sd 3:0:0:0: [sdb] Write Protect is off
[ 1068.867832] sd 3:0:0:0: [sdb] Mode Sense: 53 00 00 08
[ 1068.868157] sd 3:0:0:0: [sdb] Disabling FUA
[ 1068.868165] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1068.888006]  sdb: sdb1
[ 1068.889911] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 1100.589218] sd 3:0:0:0: [sdb] tag#0 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN 
[ 1100.589231] sd 3:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 e8 e0 88 00 00 00 08 00
[ 1100.605180] scsi host3: uas_eh_device_reset_handler start
[ 1100.733910] usb 2-1: reset SuperSpeed USB device number 2 using xhci_hcd
[ 1100.756257] scsi host3: uas_eh_device_reset_handler success
[ 1250.190545] sd 3:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 1250.190599] sd 3:0:0:0: [sdb] tag#0 Sense Key : Not Ready [current] 
[ 1250.190619] sd 3:0:0:0: [sdb] tag#0 Add. Sense: Logical unit is in process of becoming ready
[ 1250.190644] sd 3:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 e8 e0 88 00 00 00 08 00
[ 1250.190657] print_req_error: I/O error, dev sdb, sector 3907028992
[ 1331.002601] sd 3:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 1331.002636] sd 3:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] 
[ 1331.002649] sd 3:0:0:0: [sdb] tag#0 ASC=0x44 <<vendor>>ASCQ=0x81

C'est probablement un problème de connectique. J'ai touvé pas mal de liens sur internet
dont l'un rappelle un vieux temps MAITRE/ESCLAVE

..usbjmicron[,p][,x][,PORT] - this device type is for SATA disks that are behind a JMicron USB to
PATA/SATA bridge. The 48-bit ATA commands (required e.g. for ´-l xerror´, see below) do not work with
all of these bridges and are therefore disabled by default. These commands can be enabled by ´-d usb‐
jmicron,x´. If two disks are connected to a bridge with two ports, an error message is printed if no
PORT is specified. The port can be specified by ´-d usbjmicron[,x],PORT´ where PORT is 0 (master) or 1
(slave). This is not necessary if the device uses a port multiplier to connect multiple disks to one
port. The disks appear under separate /dev/ice names then. CAUTION: Specifying ´,x´ for a device
which does not support it results in I/O errors and may disconnect the drive. The same applies if the
specified PORT does not exist or is not connected to a disk.

Peux-tu regarder avec cette codification que j'ai mal comprise

sudo smartctl   -s   on  -d  usbjmicron,x,0  -T  verypermissive  -a /dev/sdb   
sudo smartctl   -s   on  -d  usbjmicron,x,1  -T  verypermissive  -a /dev/sdb  
sudo smartctl   -s   on  -d  usbjmicron,0  -T  verypermissive  -a /dev/sdb  
sudo smartctl   -s   on  -d  usbjmicron,1  -T  verypermissive  -a /dev/sdb

Dernière modification par geole (Le 31/08/2019, à 11:59)

hardouin48 · Le 31/08/2019, à 11:50

hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on  -d sat   -T  verypermissive  -a /dev/sdb
[sudo] Mot de passe de hardouin : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error medium or hardware error (serious)

=== START OF INFORMATION SECTION ===
Device Model:     [No Information Found]
Serial Number:    [No Information Found]
Firmware Version: [No Information Found]
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   [No Information Found]
Local Time is:    Sat Aug 31 12:49:46 2019 CEST
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled.
                  Checking to be sure by trying SMART RETURN STATUS command.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enable failed: scsi error medium or hardware error (serious)

Read SMART Data failed: scsi error medium or hardware error (serious)


=== START OF READ SMART DATA SECTION ===
SMART Status command failed: scsi error medium or hardware error (serious)
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.

Read SMART Error Log failed: scsi error medium or hardware error (serious)

Read SMART Self-test Log failed: scsi error medium or hardware error (serious)

Selective Self-tests/Logging not supported

hardouin@hardouin-Aspire-V3-372:~$

hardouin48 · Le 31/08/2019, à 11:51

Je vais éteindre l'ordinateur débrancher le disque puis rallumer brancher le disque avec une connexion usb qui fonctionne sur mon autre disque dur

hardouin48 · Le 31/08/2019, à 11:59

Cela ne donne rien avec le changement de connecteur

hardouin@hardouin-Aspire-V3-372:~$ sudo smartctl   -s   on  -d  usbjmicron,x,1  -T  verypermissive  -a /dev/sdb   -T  verypermissive  -a /dev/sdb
[sudo] Mot de passe de hardouin : 
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-58-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

ERROR: smartctl takes ONE device name as the final command-line argument.
You have provided 2 device names:
/dev/sdb
/dev/sdb

Use smartctl -h to get a usage summary

hardouin@hardouin-Aspire-V3-372:~$

geole · Le 31/08/2019, à 12:23

J'ai rectifié le doublon

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 31/08/2019, à 11:03

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#27 Le 31/08/2019, à 11:05

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#28 Le 31/08/2019, à 11:09

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#29 Le 31/08/2019, à 11:45

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#30 Le 31/08/2019, à 11:47

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#31 Le 31/08/2019, à 11:50

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#32 Le 31/08/2019, à 11:51

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#33 Le 31/08/2019, à 11:59

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

#34 Le 31/08/2019, à 12:23

Re : Résolu Disque dur externe neuf non reconnu par ubuntu

Pied de page des forums