#26 Le 01/01/2021, à 18:25
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
xubu1957 a écrit :
Je vais essayer d'avoir l'aide de Nico.
Les pilotes wifi Realtek ne sont pas toujours bien au point.
Ok ça marche
En attendant j'essaie de remettre les valeurs d'avant pour voir si cela refonctionne 
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#27 Le 01/01/2021, à 18:53
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Euh c'est normal que même en remettant les valeurs d'avant, je n'ai plus du tout de wifi !!!!!
Ma femme va être contente !!! 
T'as une idée au moins pour remettre comme avant STP ?
Merci d'avance
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#28 Le 01/01/2021, à 18:57
- xubu1957
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Essaye :
sudo /etc/init.d/network-manager restartou :
sudo ip link set wlo1 upConseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
En ligne
#29 Le 01/01/2021, à 19:17
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Alors j'ai pas eu besoin de relancer. J'ai arrêté le PC. Démarré, puis j'ai redémarré et on a de nouveau la wifi avec les anciens réglages que j'ai remis.
Mais je me demande si en essayant de changer les réglages et de relancer network-manager, cela pourrait peut-être fonctionner.
Je vais m'arrêter là pour aujourd'hui et je ferais des essais demain ou tard ce soir quand ma femme aura terminé d'utiliser son pc !
Merci xubu1957. Je te tiens au jus et si tu as d'autres pistes, n'hésites pas
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#30 Le 01/01/2021, à 22:55
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Hello,
J'ai quelques questions: les retours que tu as fait dans le premier message ont été entrés lorsque la carte wifi ne fonctionne pas ou lorsqu'elle fonctionne (donc après redémarrage)? Dans le premier cas, peux tu redonner tous ces retours lorsque la carte wifi ne fonctionne pas? (donc mettre le contenu des retours dans un fichier, redémarrer et envoyer le contenu du fichier). Tu pourras ajouter le retour de
dmesg aussi
Tu fais bien "éteindre" et non "mettre en veille"?
On est d'accord que tu n'as pas installé de pilote, et que tu utilises donc celui qui est déjà installé?
Sinon WPA AES/CCMP c'est parfait.
Dernière modification par Nuliel (Le 02/01/2021, à 00:04)
Hors ligne
#31 Le 01/01/2021, à 23:49
- moko138
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
avec les anciens réglages que j'ai remis.
Merci de préciser.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#32 Le 02/01/2021, à 12:55
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
moko138 a écrit :
avec les anciens réglages que j'ai remis.
Merci de préciser.
Pour info moko138 :
J'ai remis dans les paramètres swenc : N et ips : Y
c'est ce qu'on avait changé avec xubu1957 et qui entraînait à priori le fait que je ne voyais plus les réseaux wifi disponibles, mais je n'avais pas essayé de relancer ensuite le network-manager donc je vais tenter cela aujourd'hui.
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#33 Le 02/01/2021, à 12:59
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Nuliel a écrit :
Hello,
J'ai quelques questions: les retours que tu as fait dans le premier message ont été entrés lorsque la carte wifi ne fonctionne pas ou lorsqu'elle fonctionne (donc après redémarrage)? Dans le premier cas, peux tu redonner tous ces retours lorsque la carte wifi ne fonctionne pas? (donc mettre le contenu des retours dans un fichier, redémarrer et envoyer le contenu du fichier). Tu pourras ajouter le retour dedmesgaussi
Tu fais bien "éteindre" et non "mettre en veille"?
On est d'accord que tu n'as pas installé de pilote, et que tu utilises donc celui qui est déjà installé?
Sinon WPA AES/CCMP c'est parfait.
Salut Nuliel,
En effet, j'ai fait tous ces tests avec la wifi qui fonctionne donc après un redémarrage.
Je m'étais la réflexion qu'il faudrait le faire aussi quand elle est indisponible. Je vais faire cela cet aprem ok.
Et oui je fais bien éteindre et non mettre en veille (la veille me bloque tout de toute façon, l'écran ne redémarre pas, écran noir, un autre post et d'autres recherches à venir )
Ajout d'infos : j'utilise bien le driver fourni de base avec le noyau d’Ubuntu, je n'ai rien installé de plus.
Dernière modification par shyalan (Le 02/01/2021, à 14:25)
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#34 Le 02/01/2021, à 16:05
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Donc à la demande de Nuliel,
Voici le WIFI-CHECK lorsque le PC a été éteint et qu'on le rallume ... la wifi ne fonctionne pas (dans ce cas précis)
mag@mag-PC-HP:~$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 20.04 LTS
Release: 20.04
Codename: focal
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ lsusb
Bus 002 Device 003: ID 04f2:b52d Chicony Electronics Co., Ltd
Bus 002 Device 002: ID 0438:7900 Advanced Micro Devices, Inc. Root Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 0438:7900 Advanced Micro Devices, Inc. Root Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 2188:0ae1 USB OPTICAL MOUSE
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ lspci
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Root Complex
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Mullins [Radeon R2 Graphics]
00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Kabini HDMI/DP Audio
00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Host Bridge
00:02.5 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
00:08.0 Encryption controller: Advanced Micro Devices, Inc. [AMD] Kabini/Mullins PSP-Platform Security Processor
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 11)
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 39)
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39)
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39)
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 42)
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 02)
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 3
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 4
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 5
01:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ lspci -k -nn | grep -A 3 -i net
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ lspci -k
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Root Complex
Subsystem: Hewlett-Packard Company Family 16h (Models 30h-3fh) Processor Root Complex
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Mullins [Radeon R2 Graphics]
DeviceName: Onboard IGD
Subsystem: Hewlett-Packard Company Mullins [Radeon R2 Graphics]
Kernel driver in use: radeon
Kernel modules: radeon, amdgpu
00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Kabini HDMI/DP Audio
Subsystem: Hewlett-Packard Company Kabini HDMI/DP Audio
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Host Bridge
00:02.5 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Kernel driver in use: pcieport
00:08.0 Encryption controller: Advanced Micro Devices, Inc. [AMD] Kabini/Mullins PSP-Platform Security Processor
Subsystem: Hewlett-Packard Company Kabini/Mullins PSP-Platform Security Processor
Kernel driver in use: ccp
Kernel modules: ccp
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 11)
Subsystem: Hewlett-Packard Company FCH USB XHCI Controller
Kernel driver in use: xhci_hcd
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 39)
Subsystem: Hewlett-Packard Company FCH SATA Controller [AHCI mode]
Kernel driver in use: ahci
Kernel modules: ahci
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39)
Subsystem: Hewlett-Packard Company FCH USB EHCI Controller
Kernel driver in use: ehci-pci
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39)
Subsystem: Hewlett-Packard Company FCH USB EHCI Controller
Kernel driver in use: ehci-pci
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 42)
Subsystem: Hewlett-Packard Company FCH SMBus Controller
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4, sp5100_tco
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 02)
Subsystem: Hewlett-Packard Company FCH Azalia Controller
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)
Subsystem: Hewlett-Packard Company FCH LPC Bridge
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 0
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 3
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 4
Kernel driver in use: fam15h_power
Kernel modules: fam15h_power
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h (Models 30h-3fh) Processor Function 5
01:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
DeviceName: Realtek PCIE CardReader
Subsystem: Hewlett-Packard Company RTS5229 PCI Express Card Reader
Kernel driver in use: rtsx_pci
Kernel modules: rtsx_pci
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ sudo lshw -C network
[sudo] Mot de passe de mag :
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ lsmod | sort
aesni_intel 372736 0
ahci 40960 3
amdgpu 4579328 0
amd_iommu_v2 20480 1 amdgpu
autofs4 45056 2
ccp 86016 0
crc32_pclmul 16384 0
crct10dif_pclmul 16384 1
cryptd 24576 2 crypto_simd,ghash_clmulni_intel
crypto_simd 16384 1 aesni_intel
drm 491520 11 gpu_sched,drm_kms_helper,amdgpu,radeon,ttm
drm_kms_helper 184320 2 amdgpu,radeon
edac_mce_amd 32768 0
fam15h_power 16384 0
fb_sys_fops 16384 1 drm_kms_helper
ghash_clmulni_intel 16384 0
glue_helper 16384 1 aesni_intel
gpu_sched 32768 1 amdgpu
hid 131072 2 usbhid,hid_generic
hid_generic 16384 0
hp_wireless 16384 0
hp_wmi 16384 0
i2c_algo_bit 16384 2 amdgpu,radeon
i2c_piix4 28672 0
i2c_scmi 20480 0
input_leds 16384 0
ip_tables 32768 0
joydev 24576 0
k10temp 16384 0
kvm 663552 0
ledtrig_audio 16384 2 snd_hda_codec_generic,snd_hda_codec_realtek
libahci 32768 1 ahci
lp 20480 0
mac_hid 16384 0
mc 53248 4 videodev,videobuf2_v4l2,uvcvideo,videobuf2_common
memstick 20480 1 rtsx_pci_ms
Module Size Used by
nls_iso8859_1 16384 1
parport 53248 3 parport_pc,lp,ppdev
parport_pc 40960 0
ppdev 24576 0
psmouse 155648 0
radeon 1474560 15
rtsx_pci 73728 2 rtsx_pci_sdmmc,rtsx_pci_ms
rtsx_pci_ms 24576 0
rtsx_pci_sdmmc 28672 0
sch_fq_codel 20480 1
serio_raw 20480 0
snd 90112 19 snd_hda_codec_generic,snd_seq,snd_seq_device,snd_hda_codec_hdmi,snd_hwdep,snd_hda_intel,snd_hda_codec,snd_hda_codec_realtek,snd_timer,snd_pcm,snd_rawmidi
snd_hda_codec 135168 4 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_realtek
snd_hda_codec_generic 81920 1 snd_hda_codec_realtek
snd_hda_codec_hdmi 61440 1
snd_hda_codec_realtek 126976 1
snd_hda_core 90112 5 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hda_codec_realtek
snd_hda_intel 53248 4
snd_hwdep 20480 1 snd_hda_codec
snd_intel_dspcfg 24576 1 snd_hda_intel
snd_pcm 106496 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hda_core
snd_rawmidi 36864 1 snd_seq_midi
snd_seq 69632 2 snd_seq_midi,snd_seq_midi_event
snd_seq_device 16384 3 snd_seq,snd_seq_midi,snd_rawmidi
snd_seq_midi 20480 0
snd_seq_midi_event 16384 1 snd_seq_midi
snd_timer 36864 2 snd_seq,snd_pcm
soundcore 16384 1 snd
sparse_keymap 16384 1 hp_wmi
syscopyarea 16384 1 drm_kms_helper
sysfillrect 16384 1 drm_kms_helper
sysimgblt 16384 1 drm_kms_helper
ttm 106496 2 amdgpu,radeon
usbhid 57344 0
uvcvideo 98304 0
video 49152 0
videobuf2_common 49152 2 videobuf2_v4l2,uvcvideo
videobuf2_memops 20480 1 videobuf2_vmalloc
videobuf2_v4l2 24576 1 uvcvideo
videobuf2_vmalloc 20480 1 uvcvideo
videodev 225280 3 videobuf2_v4l2,uvcvideo,videobuf2_common
wmi 32768 2 hp_wmi,wmi_bmof
wmi_bmof 16384 0
x_tables 40960 1 ip_tables
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ iwconfig
lo no wireless extensions.
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ sudo iwlist scan
lo Interface doesn't support scanning.
mag@mag-PC-HP:~$
mag@mag-PC-HP:~$ uname -r -m
5.4.0-58-generic x86_64
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ cat /etc/network/interfaces
La commande « cat » n'a pas été trouvée, voulez-vous dire :
commande « cat » du deb coreutils (8.30-3ubuntu2)
Essayez : sudo apt install <nom du deb>
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ nmcli
lo: non-géré
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
Utilisez « nmcli device show » pour obtenir des informations complètes sur les>
Consultez les pages de manuel nmcli(1) et nmcli-examples(7) pour les détails c>
lines 1-7/7 (END)mag@mag-PC-HP:~$ sudo rfkill list
mag@mag-PC-HP:~$ mag@mag-PC-HP:~$ nmcli connection show
NAME UUID TYPE DEVICE
freebox_enaya 5ebb1423-42b3-4ca9-a942-28b387d396d8 wifi --
mag@mag-PC-HP:~$ Ajout de la commande de xubu1957 pour info qui donne bien sûr les paramètres lorsque la wifi fonctionne : ici le fichier n'existe même pas !!!
mag@mag-PC-HP:~$ grep [[:alnum:]] /sys/module/rtl8188ee/parameters/*
grep: /sys/module/rtl8188ee/parameters/*: Aucun fichier ou dossier de ce type
mag@mag-PC-HP:~$ Et pour finir la dernière commande demandé par toi Nuliel : Bonne lecture !!!
mag@mag-PC-HP:~$ dmesg
[ 0.000000] Linux version 5.4.0-58-generic (buildd@lcy01-amd64-004) (gcc version 9.3.0 (Ubuntu 9.3.0-17ubuntu1~20.04)) #64-Ubuntu SMP Wed Dec 9 08:16:25 UTC 2020 (Ubuntu 5.4.0-58.64-generic 5.4.73)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-5.4.0-58-generic root=UUID=aaec115f-5a64-4718-93a7-56dec65b2e28 ro quiet splash vt.handoff=7
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Hygon HygonGenuine
[ 0.000000] Centaur CentaurHauls
[ 0.000000] zhaoxin Shanghai
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007cd74fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007cd75000-0x000000007ce11fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007ce12000-0x000000007ce4efff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007ce4f000-0x000000007d00dfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007d00e000-0x000000007e1fcfff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007e1fd000-0x000000007e1fdfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e1fe000-0x000000007e205fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007e206000-0x000000007e355fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007e356000-0x000000007eacbfff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007eacc000-0x000000007eb4ffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007eb50000-0x000000007efe8fff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000007efe9000-0x000000007effffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000001beffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] e820: update [mem 0x4e9a8018-0x4e9b6c57] usable ==> usable
[ 0.000000] e820: update [mem 0x4e9a8018-0x4e9b6c57] usable ==> usable
[ 0.000000] extended physical RAM map:
[ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000009ffff] usable
[ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x000000004e9a8017] usable
[ 0.000000] reserve setup_data: [mem 0x000000004e9a8018-0x000000004e9b6c57] usable
[ 0.000000] reserve setup_data: [mem 0x000000004e9b6c58-0x000000007cd74fff] usable
[ 0.000000] reserve setup_data: [mem 0x000000007cd75000-0x000000007ce11fff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000007ce12000-0x000000007ce4efff] ACPI data
[ 0.000000] reserve setup_data: [mem 0x000000007ce4f000-0x000000007d00dfff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x000000007d00e000-0x000000007e1fcfff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000007e1fd000-0x000000007e1fdfff] usable
[ 0.000000] reserve setup_data: [mem 0x000000007e1fe000-0x000000007e205fff] ACPI NVS
[ 0.000000] reserve setup_data: [mem 0x000000007e206000-0x000000007e355fff] usable
[ 0.000000] reserve setup_data: [mem 0x000000007e356000-0x000000007eacbfff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000007eacc000-0x000000007eb4ffff] usable
[ 0.000000] reserve setup_data: [mem 0x000000007eb50000-0x000000007efe8fff] reserved
[ 0.000000] reserve setup_data: [mem 0x000000007efe9000-0x000000007effffff] usable
[ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x00000001beffffff] usable
[ 0.000000] efi: EFI v2.31 by American Megatrends
[ 0.000000] efi: ESRT=0x7e18fc18 ACPI=0x7ce26000 ACPI 2.0=0x7ce26000 SMBIOS=0x7c737010 TPMEventLog=0x6d1e4018
[ 0.000000] [Firmware Bug]: TPM Final Events table missing or invalid
[ 0.000000] secureboot: Secure boot disabled
[ 0.000000] SMBIOS 2.8 present.
[ 0.000000] DMI: HP HP Notebook /8130, BIOS F.15 05/24/2016
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 1497.189 MHz processor
[ 0.000241] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000245] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000265] last_pfn = 0x1bf000 max_arch_pfn = 0x400000000
[ 0.000275] MTRR default type: uncachable
[ 0.000277] MTRR fixed ranges enabled:
[ 0.000280] 00000-9FFFF write-back
[ 0.000283] A0000-BFFFF write-through
[ 0.000286] C0000-DFFFF uncachable
[ 0.000288] E0000-FFFFF write-protect
[ 0.000290] MTRR variable ranges enabled:
[ 0.000294] 0 base 0000000000 mask FF80000000 write-back
[ 0.000296] 1 disabled
[ 0.000298] 2 disabled
[ 0.000300] 3 disabled
[ 0.000301] 4 disabled
[ 0.000303] 5 disabled
[ 0.000304] 6 disabled
[ 0.000305] 7 disabled
[ 0.000308] TOM2: 00000001bf000000 aka 7152M
[ 0.001039] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.001182] e820: update [mem 0x80000000-0xffffffff] usable ==> reserved
[ 0.001196] last_pfn = 0x7f000 max_arch_pfn = 0x400000000
[ 0.012634] esrt: Reserving ESRT space from 0x000000007e18fc18 to 0x000000007e18fc50.
[ 0.012670] check: Scanning 1 areas for low memory corruption
[ 0.012682] Using GB pages for direct mapping
[ 0.013705] secureboot: Secure boot disabled
[ 0.013708] RAMDISK: [mem 0x3a4d9000-0x3d48ffff]
[ 0.013730] ACPI: Early table checksum verification disabled
[ 0.013739] ACPI: RSDP 0x000000007CE26000 000024 (v02 HPQOEM)
[ 0.013748] ACPI: XSDT 0x000000007CE26098 0000B4 (v01 HPQOEM SLIC-MPC 01072009 HP 00010013)
[ 0.013763] ACPI: FACP 0x000000007CE36DB0 00010C (v05 HPQOEM SLIC-MPC 01072009 HP 00010013)
[ 0.013776] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20190816/tbfadt-615)
[ 0.013789] ACPI: DSDT 0x000000007CE261E0 010BC9 (v02 HPQOEM 8130 00000000 ACPI 20051117)
[ 0.013799] ACPI: FACS 0x000000007CFFAF80 000040
[ 0.013807] ACPI: APIC 0x000000007CE36EC0 00007E (v03 HPQOEM 8130 01072009 HP 00010013)
[ 0.013816] ACPI: FPDT 0x000000007CE36F40 000044 (v01 HPQOEM 8130 01072009 HP 00010013)
[ 0.013825] ACPI: FIDT 0x000000007CE36F88 00009C (v01 HPQOEM 8130 01072009 HP 00010013)
[ 0.013834] ACPI: MCFG 0x000000007CE37028 00003C (v01 HPQOEM 8130 01072009 HP 00010013)
[ 0.013842] ACPI: BOOT 0x000000007CE37068 000028 (v01 HPQOEM 8130 01072009 HP 00010013)
[ 0.013851] ACPI: MSDM 0x000000007CE37090 000055 (v03 HPQOEM SLIC-MPC 00000001 ACPI 00010013)
[ 0.013859] ACPI: HPET 0x000000007CE370E8 000038 (v01 HPQOEM 8130 01072009 HP 00000005)
[ 0.013868] ACPI: UEFI 0x000000007CE37120 000042 (v01 HPQOEM 8130 01072009 HP 00000000)
[ 0.013876] ACPI: VFCT 0x000000007CE37168 00EC84 (v01 HPQOEM 8130 00000001 AMD 31504F47)
[ 0.013885] ACPI: SSDT 0x000000007CE45DF0 00096C (v01 HPQOEM 8130 00000001 ACPI 00000001)
[ 0.013894] ACPI: SSDT 0x000000007CE46760 0048A6 (v02 HPQOEM 8130 00000002 ACPI 04000000)
[ 0.013902] ACPI: TPM2 0x000000007CE4B008 000034 (v03 HPQOEM 8130 00000001 HP 00000000)
[ 0.013911] ACPI: SSDT 0x000000007CE4B040 00071B (v01 HPQOEM 8130 00000001 ACPI 20051117)
[ 0.013920] ACPI: SSDT 0x000000007CE4B760 001207 (v01 HPQOEM 8130 00000001 ACPI 20051117)
[ 0.013928] ACPI: SSDT 0x000000007CE4C968 001457 (v01 HPQOEM 8130 00000001 ACPI 20051117)
[ 0.013937] ACPI: SSDT 0x000000007CE4DDC0 000FB2 (v01 HPQOEM 8130 00000001 ACPI 20051117)
[ 0.013946] ACPI: BGRT 0x000000007CE4ED78 000038 (v01 HPQOEM 8130 01072009 HP 00010013)
[ 0.013969] ACPI: Local APIC address 0xfee00000
[ 0.014362] No NUMA configuration found
[ 0.014365] Faking a node at [mem 0x0000000000000000-0x00000001beffffff]
[ 0.014390] NODE_DATA(0) allocated [mem 0x1befd5000-0x1beffffff]
[ 0.015338] Zone ranges:
[ 0.015340] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.015343] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.015345] Normal [mem 0x0000000100000000-0x00000001beffffff]
[ 0.015348] Device empty
[ 0.015350] Movable zone start for each node
[ 0.015356] Early memory node ranges
[ 0.015358] node 0: [mem 0x0000000000001000-0x000000000009ffff]
[ 0.015361] node 0: [mem 0x0000000000100000-0x000000007cd74fff]
[ 0.015363] node 0: [mem 0x000000007e1fd000-0x000000007e1fdfff]
[ 0.015365] node 0: [mem 0x000000007e206000-0x000000007e355fff]
[ 0.015367] node 0: [mem 0x000000007eacc000-0x000000007eb4ffff]
[ 0.015368] node 0: [mem 0x000000007efe9000-0x000000007effffff]
[ 0.015370] node 0: [mem 0x0000000100000000-0x00000001beffffff]
[ 0.015757] Zeroed struct page in unavailable ranges: 16640 pages
[ 0.015761] Initmem setup node 0 [mem 0x0000000000001000-0x00000001beffffff]
[ 0.015765] On node 0 totalpages: 1294080
[ 0.015768] DMA zone: 64 pages used for memmap
[ 0.015770] DMA zone: 22 pages reserved
[ 0.015773] DMA zone: 3999 pages, LIFO batch:0
[ 0.015956] DMA32 zone: 7934 pages used for memmap
[ 0.015959] DMA32 zone: 507745 pages, LIFO batch:63
[ 0.043980] Normal zone: 12224 pages used for memmap
[ 0.043986] Normal zone: 782336 pages, LIFO batch:63
[ 0.073371] ACPI: PM-Timer IO Port: 0x808
[ 0.073379] ACPI: Local APIC address 0xfee00000
[ 0.073397] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.073413] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[ 0.073421] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[ 0.073426] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.073430] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.073433] ACPI: IRQ0 used by override.
[ 0.073435] ACPI: IRQ9 used by override.
[ 0.073440] Using ACPI (MADT) for SMP configuration information
[ 0.073443] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.073467] e820: update [mem 0x7a8dc000-0x7a8f1fff] usable ==> reserved
[ 0.073493] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.073550] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.073554] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.073559] PM: Registered nosave memory: [mem 0x4e9a8000-0x4e9a8fff]
[ 0.073563] PM: Registered nosave memory: [mem 0x4e9b6000-0x4e9b6fff]
[ 0.073567] PM: Registered nosave memory: [mem 0x7a8dc000-0x7a8f1fff]
[ 0.073571] PM: Registered nosave memory: [mem 0x7cd75000-0x7ce11fff]
[ 0.073573] PM: Registered nosave memory: [mem 0x7ce12000-0x7ce4efff]
[ 0.073574] PM: Registered nosave memory: [mem 0x7ce4f000-0x7d00dfff]
[ 0.073576] PM: Registered nosave memory: [mem 0x7d00e000-0x7e1fcfff]
[ 0.073580] PM: Registered nosave memory: [mem 0x7e1fe000-0x7e205fff]
[ 0.073584] PM: Registered nosave memory: [mem 0x7e356000-0x7eacbfff]
[ 0.073589] PM: Registered nosave memory: [mem 0x7eb50000-0x7efe8fff]
[ 0.073593] PM: Registered nosave memory: [mem 0x7f000000-0xfebfffff]
[ 0.073595] PM: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[ 0.073596] PM: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[ 0.073597] PM: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[ 0.073599] PM: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[ 0.073600] PM: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[ 0.073602] PM: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[ 0.073603] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[ 0.073604] PM: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[ 0.073606] PM: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[ 0.073607] PM: Registered nosave memory: [mem 0xfed90000-0xfeffffff]
[ 0.073608] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.073613] [mem 0x7f000000-0xfebfffff] available for PCI devices
[ 0.073615] Booting paravirtualized kernel on bare hardware
[ 0.073622] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.073639] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.074514] percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u524288
[ 0.074542] pcpu-alloc: s184320 r8192 d28672 u524288 alloc=1*2097152
[ 0.074545] pcpu-alloc: [0] 0 1 2 3
[ 0.074632] Built 1 zonelists, mobility grouping on. Total pages: 1273836
[ 0.074633] Policy zone: Normal
[ 0.074637] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.4.0-58-generic root=UUID=aaec115f-5a64-4718-93a7-56dec65b2e28 ro quiet splash vt.handoff=7
[ 0.077299] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.078553] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.078619] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.098349] Calgary: detecting Calgary via BIOS EBDA area
[ 0.098354] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.135880] Memory: 4892072K/5176320K available (14339K kernel code, 2426K rwdata, 4932K rodata, 2720K init, 4956K bss, 284248K reserved, 0K cma-reserved)
[ 0.135896] random: get_random_u64 called from kmem_cache_open+0x2d/0x410 with crng_init=0
[ 0.136272] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.136309] ftrace: allocating 44541 entries in 174 pages
[ 0.175168] rcu: Hierarchical RCU implementation.
[ 0.175174] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[ 0.175175] Tasks RCU enabled.
[ 0.175177] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.175179] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.184958] NR_IRQS: 524544, nr_irqs: 1000, preallocated irqs: 16
[ 0.185593] random: crng done (trusting CPU's manufacturer)
[ 0.185643] vt handoff: transparent VT on vt#7
[ 0.185663] Console: colour dummy device 80x25
[ 0.185673] printk: console [tty0] enabled
[ 0.185717] ACPI: Core revision 20190816
[ 0.186232] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.186256] APIC: Switch to symmetric I/O mode setup
[ 0.187046] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.206257] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x1594c333f39, max_idle_ns: 440795210089 ns
[ 0.206267] Calibrating delay loop (skipped), value calculated using timer frequency.. 2994.37 BogoMIPS (lpj=5988756)
[ 0.206272] pid_max: default: 32768 minimum: 301
[ 0.209950] LSM: Security Framework initializing
[ 0.209979] Yama: becoming mindful.
[ 0.210050] AppArmor: AppArmor initialized
[ 0.210170] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.210210] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.210266] *** VALIDATE tmpfs ***
[ 0.210637] *** VALIDATE proc ***
[ 0.210777] *** VALIDATE cgroup1 ***
[ 0.210781] *** VALIDATE cgroup2 ***
[ 0.210860] BIOS may not properly restore RDRAND after suspend, hiding RDRAND via CPUID. Use rdrand=force to reenable.
[ 0.210886] LVT offset 1 assigned for vector 0xf9
[ 0.210895] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
[ 0.210897] Last level dTLB entries: 4KB 512, 2MB 256, 4MB 128, 1GB 0
[ 0.210905] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.210908] Spectre V2 : Mitigation: Full AMD retpoline
[ 0.210909] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.210913] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[ 0.211272] Freeing SMP alternatives memory: 40K
[ 0.327609] smpboot: CPU0: AMD E2-6110 APU with AMD Radeon R2 Graphics (family: 0x16, model: 0x30, stepping: 0x1)
[ 0.328034] Performance Events: AMD PMU driver.
[ 0.328041] ... version: 0
[ 0.328042] ... bit width: 48
[ 0.328044] ... generic registers: 4
[ 0.328045] ... value mask: 0000ffffffffffff
[ 0.328046] ... max period: 00007fffffffffff
[ 0.328048] ... fixed-purpose events: 0
[ 0.328049] ... event mask: 000000000000000f
[ 0.328146] rcu: Hierarchical SRCU implementation.
[ 0.329423] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.329611] smp: Bringing up secondary CPUs ...
[ 0.329987] x86: Booting SMP configuration:
[ 0.329990] .... node #0, CPUs: #1 #2 #3
[ 0.336758] smp: Brought up 1 node, 4 CPUs
[ 0.336758] smpboot: Max logical packages: 1
[ 0.336758] smpboot: Total of 4 processors activated (11977.51 BogoMIPS)
[ 0.338574] devtmpfs: initialized
[ 0.338574] x86/mm: Memory block size: 128MB
[ 0.339811] PM: Registering ACPI NVS region [mem 0x7ce4f000-0x7d00dfff] (1830912 bytes)
[ 0.339811] PM: Registering ACPI NVS region [mem 0x7e1fe000-0x7e205fff] (32768 bytes)
[ 0.339811] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.339811] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.339811] pinctrl core: initialized pinctrl subsystem
[ 0.339811] PM: RTC time: 13:14:43, date: 2021-01-02
[ 0.339811] NET: Registered protocol family 16
[ 0.339811] audit: initializing netlink subsys (disabled)
[ 0.339811] audit: type=2000 audit(1609593283.152:1): state=initialized audit_enabled=0 res=1
[ 0.342313] EISA bus registered
[ 0.342335] cpuidle: using governor ladder
[ 0.342346] cpuidle: using governor menu
[ 0.342387] Simple Boot Flag at 0x47 set to 0x1
[ 0.342438] ACPI: bus type PCI registered
[ 0.342441] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.342649] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.342656] PCI: not using MMCONFIG
[ 0.342658] PCI: Using configuration type 1 for base access
[ 0.342658] PCI: Using configuration type 1 for extended access
[ 0.346937] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.346937] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.350538] ACPI: Added _OSI(Module Device)
[ 0.350540] ACPI: Added _OSI(Processor Device)
[ 0.350542] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.350544] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.350547] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.350549] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.350551] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[ 0.405089] ACPI: 7 ACPI AML tables successfully acquired and loaded
[ 0.411323] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.416774] ACPI: EC: EC started
[ 0.416776] ACPI: EC: interrupt blocked
[ 0.986003] ACPI: \_SB_.PCI0.SBRG.EC0_: Used as first EC
[ 0.986011] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x3, IRQ=-1, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.986014] ACPI: \_SB_.PCI0.SBRG.EC0_: Boot DSDT EC used to handle transactions
[ 0.986016] ACPI: Interpreter enabled
[ 0.986099] ACPI: (supports S0 S3 S4 S5)
[ 0.986102] ACPI: Using IOAPIC for interrupt routing
[ 0.986247] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.986429] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.986473] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.987635] ACPI: Enabled 5 GPEs in block 00 to 1F
[ 1.015967] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.015982] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[ 1.016773] acpi PNP0A03:00: _OSC: platform does not support [PME LTR]
[ 1.017533] acpi PNP0A03:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug AER PCIeCapability]
[ 1.018607] PCI host bridge to bus 0000:00
[ 1.018613] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 1.018617] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 1.018620] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 1.018623] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 1.018626] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 1.018630] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 1.018633] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[ 1.018636] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.018660] pci 0000:00:00.0: [1022:1566] type 00 class 0x060000
[ 1.018941] pci 0000:00:01.0: [1002:9852] type 00 class 0x030000
[ 1.018970] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 1.018982] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[ 1.018992] pci 0000:00:01.0: reg 0x20: [io 0xf000-0xf0ff]
[ 1.019001] pci 0000:00:01.0: reg 0x24: [mem 0xfeb00000-0xfeb3ffff]
[ 1.019010] pci 0000:00:01.0: reg 0x30: [mem 0xfeb40000-0xfeb5ffff pref]
[ 1.019020] pci 0000:00:01.0: enabling Extended Tags
[ 1.019040] pci 0000:00:01.0: BAR 0: assigned to efifb
[ 1.019089] pci 0000:00:01.0: supports D1 D2
[ 1.019092] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[ 1.019328] pci 0000:00:01.1: [1002:9840] type 00 class 0x040300
[ 1.019351] pci 0000:00:01.1: reg 0x10: [mem 0xfeb64000-0xfeb67fff 64bit]
[ 1.019379] pci 0000:00:01.1: enabling Extended Tags
[ 1.019431] pci 0000:00:01.1: supports D1 D2
[ 1.019611] pci 0000:00:02.0: [1022:156b] type 00 class 0x060000
[ 1.019825] pci 0000:00:02.5: [1022:1439] type 01 class 0x060400
[ 1.019877] pci 0000:00:02.5: enabling Extended Tags
[ 1.019940] pci 0000:00:02.5: PME# supported from D0 D3hot D3cold
[ 1.020181] pci 0000:00:08.0: [1022:1537] type 00 class 0x108000
[ 1.020201] pci 0000:00:08.0: reg 0x10: [mem 0xd0800000-0xd081ffff 64bit pref]
[ 1.020210] pci 0000:00:08.0: reg 0x18: [mem 0xfe900000-0xfe9fffff]
[ 1.020218] pci 0000:00:08.0: reg 0x1c: [mem 0xfeb6f000-0xfeb6ffff]
[ 1.020230] pci 0000:00:08.0: reg 0x24: [mem 0xfeb6a000-0xfeb6bfff]
[ 1.020449] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[ 1.020481] pci 0000:00:10.0: reg 0x10: [mem 0xfeb68000-0xfeb69fff 64bit]
[ 1.020604] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[ 1.020844] pci 0000:00:11.0: [1022:7804] type 00 class 0x010601
[ 1.020868] pci 0000:00:11.0: reg 0x10: [io 0xf140-0xf147]
[ 1.020879] pci 0000:00:11.0: reg 0x14: [io 0xf130-0xf133]
[ 1.020890] pci 0000:00:11.0: reg 0x18: [io 0xf120-0xf127]
[ 1.020900] pci 0000:00:11.0: reg 0x1c: [io 0xf110-0xf113]
[ 1.020910] pci 0000:00:11.0: reg 0x20: [io 0xf100-0xf10f]
[ 1.020921] pci 0000:00:11.0: reg 0x24: [mem 0xfeb6e000-0xfeb6e3ff]
[ 1.020979] pci 0000:00:11.0: PME# supported from D3hot
[ 1.021395] pci 0000:00:12.0: [1022:7808] type 00 class 0x0c0320
[ 1.021419] pci 0000:00:12.0: reg 0x10: [mem 0xfeb6d000-0xfeb6d0ff]
[ 1.021506] pci 0000:00:12.0: supports D1 D2
[ 1.021509] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.021725] pci 0000:00:13.0: [1022:7808] type 00 class 0x0c0320
[ 1.021749] pci 0000:00:13.0: reg 0x10: [mem 0xfeb6c000-0xfeb6c0ff]
[ 1.021835] pci 0000:00:13.0: supports D1 D2
[ 1.021838] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.022050] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[ 1.022296] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[ 1.022323] pci 0000:00:14.2: reg 0x10: [mem 0xfeb60000-0xfeb63fff 64bit]
[ 1.022398] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 1.022613] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[ 1.022898] pci 0000:00:18.0: [1022:1580] type 00 class 0x060000
[ 1.023094] pci 0000:00:18.1: [1022:1581] type 00 class 0x060000
[ 1.023279] pci 0000:00:18.2: [1022:1582] type 00 class 0x060000
[ 1.023475] pci 0000:00:18.3: [1022:1583] type 00 class 0x060000
[ 1.023666] pci 0000:00:18.4: [1022:1584] type 00 class 0x060000
[ 1.023850] pci 0000:00:18.5: [1022:1585] type 00 class 0x060000
[ 1.024138] pci 0000:01:00.0: [10ec:5229] type 00 class 0xff0000
[ 1.024169] pci 0000:01:00.0: reg 0x10: [mem 0xfea00000-0xfea00fff]
[ 1.024302] pci 0000:01:00.0: supports D1 D2
[ 1.024306] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
[ 1.024461] pci 0000:00:02.5: PCI bridge to [bus 01]
[ 1.024471] pci 0000:00:02.5: bridge window [mem 0xfea00000-0xfeafffff]
[ 1.032112] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[ 1.032342] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[ 1.032624] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[ 1.032899] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[ 1.033125] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 1.033319] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 1.033511] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 1.033704] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 1.035858] ACPI: EC: interrupt unblocked
[ 1.035861] ACPI: EC: event unblocked
[ 1.035871] ACPI: \_SB_.PCI0.SBRG.EC0_: GPE=0x3, IRQ=-1, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 1.035875] ACPI: \_SB_.PCI0.SBRG.EC0_: Boot DSDT EC used to handle transactions and events
[ 1.036044] iommu: Default domain type: Translated
[ 1.036044] SCSI subsystem initialized
[ 1.036044] libata version 3.00 loaded.
[ 1.036044] pci 0000:00:01.0: vgaarb: setting as boot VGA device
[ 1.036044] pci 0000:00:01.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 1.036044] pci 0000:00:01.0: vgaarb: bridge control possible
[ 1.036044] vgaarb: loaded
[ 1.036044] ACPI: bus type USB registered
[ 1.036044] usbcore: registered new interface driver usbfs
[ 1.036044] usbcore: registered new interface driver hub
[ 1.036044] usbcore: registered new device driver usb
[ 1.036044] pps_core: LinuxPPS API ver. 1 registered
[ 1.036044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.036044] PTP clock support registered
[ 1.036044] EDAC MC: Ver: 3.0.0
[ 1.036044] Registered efivars operations
[ 1.036044] PCI: Using ACPI for IRQ routing
[ 1.045059] PCI: pci_cache_line_size set to 64 bytes
[ 1.045123] e820: reserve RAM buffer [mem 0x4e9a8018-0x4fffffff]
[ 1.045126] e820: reserve RAM buffer [mem 0x7a8dc000-0x7bffffff]
[ 1.045129] e820: reserve RAM buffer [mem 0x7cd75000-0x7fffffff]
[ 1.045131] e820: reserve RAM buffer [mem 0x7e1fe000-0x7fffffff]
[ 1.045133] e820: reserve RAM buffer [mem 0x7e356000-0x7fffffff]
[ 1.045136] e820: reserve RAM buffer [mem 0x7eb50000-0x7fffffff]
[ 1.045137] e820: reserve RAM buffer [mem 0x7f000000-0x7fffffff]
[ 1.045139] e820: reserve RAM buffer [mem 0x1bf000000-0x1bfffffff]
[ 1.045387] NetLabel: Initializing
[ 1.045388] NetLabel: domain hash size = 128
[ 1.045390] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 1.045429] NetLabel: unlabeled traffic allowed by default
[ 1.046402] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.046409] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 1.047363] clocksource: Switched to clocksource tsc-early
[ 1.081543] *** VALIDATE bpf ***
[ 1.081743] VFS: Disk quotas dquot_6.6.0
[ 1.081791] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.081855] *** VALIDATE ramfs ***
[ 1.081863] *** VALIDATE hugetlbfs ***
[ 1.082121] AppArmor: AppArmor Filesystem Enabled
[ 1.082192] pnp: PnP ACPI init
[ 1.082612] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.082626] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.082851] system 00:01: [mem 0x80000000-0xbfffffff] has been reserved
[ 1.082862] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.083069] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.083206] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.083369] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 1.083380] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.083483] pnp 00:05: Plug and Play ACPI device, IDs HPQ8001 PNP0303 (active)
[ 1.083561] pnp 00:06: Plug and Play ACPI device, IDs SYN3202 PNP0f13 (active)
[ 1.084511] system 00:07: [io 0x04d0-0x04d1] has been reserved
[ 1.084516] system 00:07: [io 0x040b] has been reserved
[ 1.084519] system 00:07: [io 0x04d6] has been reserved
[ 1.084523] system 00:07: [io 0x0c00-0x0c01] has been reserved
[ 1.084526] system 00:07: [io 0x0c14] has been reserved
[ 1.084530] system 00:07: [io 0x0c50-0x0c51] has been reserved
[ 1.084533] system 00:07: [io 0x0c52] has been reserved
[ 1.084536] system 00:07: [io 0x0c6c] has been reserved
[ 1.084539] system 00:07: [io 0x0c6f] has been reserved
[ 1.084543] system 00:07: [io 0x0cd0-0x0cd1] has been reserved
[ 1.084546] system 00:07: [io 0x0cd2-0x0cd3] has been reserved
[ 1.084549] system 00:07: [io 0x0cd4-0x0cd5] has been reserved
[ 1.084552] system 00:07: [io 0x0cd6-0x0cd7] has been reserved
[ 1.084556] system 00:07: [io 0x0cd8-0x0cdf] has been reserved
[ 1.084559] system 00:07: [io 0x0800-0x089f] has been reserved
[ 1.084563] system 00:07: [io 0x0b20-0x0b3f] has been reserved
[ 1.084566] system 00:07: [io 0x0900-0x090f] has been reserved
[ 1.084569] system 00:07: [io 0x0910-0x091f] has been reserved
[ 1.084573] system 00:07: [io 0xfe00-0xfefe] has been reserved
[ 1.084578] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 1.084582] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[ 1.084586] system 00:07: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 1.084590] system 00:07: [mem 0xfed61000-0xfed70fff] has been reserved
[ 1.084594] system 00:07: [mem 0xfec10000-0xfec10fff] has been reserved
[ 1.084597] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[ 1.084608] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.088731] pnp: PnP ACPI: found 8 devices
[ 1.093234] thermal_sys: Registered thermal governor 'fair_share'
[ 1.093236] thermal_sys: Registered thermal governor 'bang_bang'
[ 1.093238] thermal_sys: Registered thermal governor 'step_wise'
[ 1.093240] thermal_sys: Registered thermal governor 'user_space'
[ 1.093241] thermal_sys: Registered thermal governor 'power_allocator'
[ 1.097757] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 1.097871] pci 0000:00:02.5: PCI bridge to [bus 01]
[ 1.097881] pci 0000:00:02.5: bridge window [mem 0xfea00000-0xfeafffff]
[ 1.097895] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 1.097898] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 1.097902] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 1.097905] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 1.097908] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 1.097911] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 1.097915] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff window]
[ 1.097918] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
[ 1.098134] NET: Registered protocol family 2
[ 1.098631] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 1.098809] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.099345] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 1.099583] TCP: Hash tables configured (established 65536 bind 65536)
[ 1.099748] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 1.099841] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 1.100037] NET: Registered protocol family 1
[ 1.100050] NET: Registered protocol family 44
[ 1.100083] pci 0000:00:01.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 1.100097] pci 0000:00:01.1: D0 power state depends on 0000:00:01.0
[ 1.122841] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x662 took 21565 usecs
[ 1.122847] pci 0000:00:12.0: PME# does not work under D3, disabling it
[ 1.142827] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x662 took 19482 usecs
[ 1.142833] pci 0000:00:13.0: PME# does not work under D3, disabling it
[ 1.142887] PCI: CLS 64 bytes, default 64
[ 1.143047] Trying to unpack rootfs image as initramfs...
[ 1.530688] Initramfs unpacking failed: Decoding failed
[ 1.549820] Freeing initrd memory: 48860K
[ 1.549884] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.549888] software IO TLB: mapped [mem 0x7645d000-0x7a45d000] (64MB)
[ 1.550015] amd_uncore: AMD NB counters detected
[ 1.550021] amd_uncore: AMD LLC counters detected
[ 1.550363] LVT offset 0 assigned for vector 0x400
[ 1.550442] perf: AMD IBS detected (0x000000ff)
[ 1.550566] check: Scanning for low memory corruption every 60 seconds
[ 1.551701] Initialise system trusted keyrings
[ 1.551729] Key type blacklist registered
[ 1.551855] workingset: timestamp_bits=36 max_order=21 bucket_order=0
[ 1.555486] zbud: loaded
[ 1.556407] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.556900] fuse: init (API version 7.31)
[ 1.556944] *** VALIDATE fuse ***
[ 1.556948] *** VALIDATE fuse ***
[ 1.557211] Platform Keyring initialized
[ 1.568116] Key type asymmetric registered
[ 1.568118] Asymmetric key parser 'x509' registered
[ 1.568137] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 1.568250] io scheduler mq-deadline registered
[ 1.569074] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1.569221] efifb: probing for efifb
[ 1.569302] efifb: showing boot graphics
[ 1.571197] efifb: framebuffer at 0xc0000000, using 5628k, total 5625k
[ 1.571200] efifb: mode is 1600x900x32, linelength=6400, pages=1
[ 1.571200] efifb: scrolling: redraw
[ 1.571204] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.571332] fbcon: Deferring console take-over
[ 1.571335] fb0: EFI VGA frame buffer device
[ 1.631513] ACPI: AC Adapter [ACAD] (on-line)
[ 1.631688] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.631734] ACPI: Power Button [PWRB]
[ 1.631829] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 1.631881] ACPI: Lid Switch [LID]
[ 1.631962] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.632043] ACPI: Power Button [PWRF]
[ 1.637514] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.637516] ACPI: Thermal Zone [THRM] (0 C)
[ 1.637900] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.642792] Linux agpgart interface v0.103
[ 1.644299] tpm_crb MSFT0101:00: [Firmware Bug]: ACPI region does not cover the entire command/response buffer. [mem 0x7d004000-0x7d004fff flags 0x200] vs 7d004000 4000
[ 1.644309] tpm_crb MSFT0101:00: can't request region for resource [mem 0x7d004000-0x7d004fff]
[ 1.644321] tpm_crb: probe of MSFT0101:00 failed with error -16
[ 1.649332] loop: module loaded
[ 1.649922] libphy: Fixed MDIO Bus: probed
[ 1.649924] tun: Universal TUN/TAP device driver, 1.6
[ 1.650031] PPP generic driver version 2.4.2
[ 1.650179] VFIO - User Level meta-driver version: 0.3
[ 1.650443] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.650462] ehci-pci: EHCI PCI platform driver
[ 1.650795] ehci-pci 0000:00:12.0: EHCI Host Controller
[ 1.650810] ehci-pci 0000:00:12.0: new USB bus registered, assigned bus number 1
[ 1.650819] ehci-pci 0000:00:12.0: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.650830] ehci-pci 0000:00:12.0: debug port 2
[ 1.650912] ehci-pci 0000:00:12.0: irq 18, io mem 0xfeb6d000
[ 1.668444] battery: ACPI: Battery Slot [BAT0] (battery present)
[ 1.670326] ehci-pci 0000:00:12.0: USB 2.0 started, EHCI 1.00
[ 1.670465] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.670469] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.670472] usb usb1: Product: EHCI Host Controller
[ 1.670475] usb usb1: Manufacturer: Linux 5.4.0-58-generic ehci_hcd
[ 1.670478] usb usb1: SerialNumber: 0000:00:12.0
[ 1.670755] hub 1-0:1.0: USB hub found
[ 1.670773] hub 1-0:1.0: 2 ports detected
[ 1.671269] ehci-pci 0000:00:13.0: EHCI Host Controller
[ 1.671282] ehci-pci 0000:00:13.0: new USB bus registered, assigned bus number 2
[ 1.671289] ehci-pci 0000:00:13.0: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.671300] ehci-pci 0000:00:13.0: debug port 2
[ 1.671354] ehci-pci 0000:00:13.0: irq 18, io mem 0xfeb6c000
[ 1.686454] ehci-pci 0000:00:13.0: USB 2.0 started, EHCI 1.00
[ 1.686614] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.686618] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.686621] usb usb2: Product: EHCI Host Controller
[ 1.686624] usb usb2: Manufacturer: Linux 5.4.0-58-generic ehci_hcd
[ 1.686627] usb usb2: SerialNumber: 0000:00:13.0
[ 1.686978] hub 2-0:1.0: USB hub found
[ 1.686998] hub 2-0:1.0: 2 ports detected
[ 1.687328] ehci-platform: EHCI generic platform driver
[ 1.687375] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.687381] ohci-pci: OHCI PCI platform driver
[ 1.687406] ohci-platform: OHCI generic platform driver
[ 1.687429] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.687745] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.687759] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 3
[ 1.687950] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x0000000000000410
[ 1.688386] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.688390] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.688393] usb usb3: Product: xHCI Host Controller
[ 1.688396] usb usb3: Manufacturer: Linux 5.4.0-58-generic xhci-hcd
[ 1.688398] usb usb3: SerialNumber: 0000:00:10.0
[ 1.688641] hub 3-0:1.0: USB hub found
[ 1.688661] hub 3-0:1.0: 2 ports detected
[ 1.688915] xhci_hcd 0000:00:10.0: xHCI Host Controller
[ 1.688922] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 4
[ 1.688930] xhci_hcd 0000:00:10.0: Host supports USB 3.0 SuperSpeed
[ 1.691357] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.691426] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[ 1.691430] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.691432] usb usb4: Product: xHCI Host Controller
[ 1.691435] usb usb4: Manufacturer: Linux 5.4.0-58-generic xhci-hcd
[ 1.691438] usb usb4: SerialNumber: 0000:00:10.0
[ 1.691688] hub 4-0:1.0: USB hub found
[ 1.691706] hub 4-0:1.0: 2 ports detected
[ 1.692047] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.698509] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.698518] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.698833] mousedev: PS/2 mouse device common for all mice
[ 1.699193] rtc_cmos 00:03: RTC can wake from S4
[ 1.699471] rtc_cmos 00:03: registered as rtc0
[ 1.699520] rtc_cmos 00:03: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.699539] i2c /dev entries driver
[ 1.699636] device-mapper: uevent: version 1.0.3
[ 1.699794] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com
[ 1.699836] platform eisa.0: Probing EISA bus 0
[ 1.699840] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 1.699843] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 1.699846] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 1.699849] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 1.699852] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 1.699855] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 1.699858] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 1.699860] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 1.699863] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 1.699866] platform eisa.0: EISA: Detected 0 cards
[ 1.699991] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.699997] EFI Variables Facility v0.08 2004-May-17
[ 1.707014] x86/pm: family 0x16 cpu detected, MSR saving is needed during suspending.
[ 1.707070] drop_monitor: Initializing network drop monitor service
[ 1.707497] NET: Registered protocol family 10
[ 1.709558] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.723619] Segment Routing with IPv6
[ 1.723678] NET: Registered protocol family 17
[ 1.723827] Key type dns_resolver registered
[ 1.724425] RAS: Correctable Errors collector initialized.
[ 1.724544] microcode: CPU0: patch_level=0x07030105
[ 1.724576] microcode: CPU1: patch_level=0x07030105
[ 1.724605] microcode: CPU2: patch_level=0x07030105
[ 1.724617] microcode: CPU3: patch_level=0x07030105
[ 1.724696] microcode: Microcode Update Driver: v2.2.
[ 1.724707] IPI shorthand broadcast: enabled
[ 1.724724] sched_clock: Marking stable (1723840689, 844059)->(1736408607, -11723859)
[ 1.724892] registered taskstats version 1
[ 1.724915] Loading compiled-in X.509 certificates
[ 1.727130] Loaded X.509 cert 'Build time autogenerated kernel key: 6b3d3d266049f4a4077ed3557f79f9ce7832433a'
[ 1.727212] zswap: loaded using pool lzo/zbud
[ 1.727415] Key type ._fscrypt registered
[ 1.727417] Key type .fscrypt registered
[ 1.741963] Key type big_key registered
[ 1.748940] Key type encrypted registered
[ 1.748950] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.749223] integrity: Loading X.509 certificate: UEFI:db
[ 1.749317] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
[ 1.749319] integrity: Loading X.509 certificate: UEFI:db
[ 1.749372] integrity: Loaded X.509 cert 'Hewlett-Packard Company: HP UEFI Secure Boot 2013 DB key: 1d7cf2c2b92673f69c8ee1ec7063967ab9b62bec'
[ 1.749373] integrity: Loading X.509 certificate: UEFI:db
[ 1.749431] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
[ 1.749641] integrity: Loading X.509 certificate: UEFI:MokListRT
[ 1.749687] integrity: Loaded X.509 cert 'SomeOrg: shim: a01ee84e9b37ace407961cc468c5909447878469'
[ 1.749688] integrity: Loading X.509 certificate: UEFI:MokListRT
[ 1.750560] integrity: Loaded X.509 cert 'Canonical Ltd. Master Certificate Authority: ad91990bc22ab1f517048c23b6655a268e345a63'
[ 1.751219] ima: No TPM chip found, activating TPM-bypass!
[ 1.751227] ima: Allocated hash algorithm: sha1
[ 1.751244] ima: No architecture policies found
[ 1.751274] evm: Initialising EVM extended attributes:
[ 1.751276] evm: security.selinux
[ 1.751277] evm: security.SMACK64
[ 1.751278] evm: security.SMACK64EXEC
[ 1.751279] evm: security.SMACK64TRANSMUTE
[ 1.751280] evm: security.SMACK64MMAP
[ 1.751281] evm: security.apparmor
[ 1.751282] evm: security.ima
[ 1.751283] evm: security.capability
[ 1.751284] evm: HMAC attrs: 0x1
[ 1.752278] PM: Magic number: 5:663:229
[ 1.752512] rtc_cmos 00:03: setting system clock to 2021-01-02T13:14:44 UTC (1609593284)
[ 1.752842] acpi_cpufreq: overriding BIOS provided _PSD data
[ 1.756715] Freeing unused decrypted memory: 2040K
[ 1.758143] Freeing unused kernel image memory: 2720K
[ 1.770504] Write protecting the kernel read-only data: 22528k
[ 1.771735] Freeing unused kernel image memory: 2008K
[ 1.772401] Freeing unused kernel image memory: 1212K
[ 1.803435] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 1.803443] Run /init as init process
[ 2.006476] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 2.022508] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 2.022545] usb 3-1: new low-speed USB device number 2 using xhci_hcd
[ 2.111408] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.112261] acpi device:01: registered as cooling_device4
[ 2.112406] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input5
[ 2.162632] usb 1-1: New USB device found, idVendor=0438, idProduct=7900, bcdDevice= 0.18
[ 2.162638] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.163068] hub 1-1:1.0: USB hub found
[ 2.163124] hub 1-1:1.0: 4 ports detected
[ 2.169123] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 2.169129] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection
[ 2.169545] rtsx_pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 2.170372] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[ 2.173717] ahci 0000:00:11.0: version 3.0
[ 2.174143] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[ 2.174150] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 2.182703] usb 2-1: New USB device found, idVendor=0438, idProduct=7900, bcdDevice= 0.18
[ 2.182711] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.183135] hub 2-1:1.0: USB hub found
[ 2.183188] hub 2-1:1.0: 4 ports detected
[ 2.199085] scsi host0: ahci
[ 2.200430] usb 3-1: New USB device found, idVendor=2188, idProduct=0ae1, bcdDevice= 1.00
[ 2.200435] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.200438] usb 3-1: Product: USB OPTICAL MOUSE
[ 2.202835] scsi host1: ahci
[ 2.202998] ata1: SATA max UDMA/133 abar m1024@0xfeb6e000 port 0xfeb6e100 irq 33
[ 2.203002] ata2: SATA max UDMA/133 abar m1024@0xfeb6e000 port 0xfeb6e180 irq 33
[ 2.276057] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.293098] usbcore: registered new interface driver usbhid
[ 2.293101] usbhid: USB HID core driver
[ 2.323263] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:10.0/usb3/3-1/3-1:1.0/0003:2188:0AE1.0001/input/input7
[ 2.323512] hid-generic 0003:2188:0AE1.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:10.0-1/input0
[ 2.470422] usb 2-1.2: new high-speed USB device number 3 using ehci-pci
[ 2.586338] tsc: Refined TSC clocksource calibration: 1497.191 MHz
[ 2.586357] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1594c522ce2, max_idle_ns: 440795237962 ns
[ 2.586411] clocksource: Switched to clocksource tsc
[ 2.599270] usb 2-1.2: New USB device found, idVendor=04f2, idProduct=b52d, bcdDevice=40.60
[ 2.599278] usb 2-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.599282] usb 2-1.2: Product: HP Webcam
[ 2.599285] usb 2-1.2: Manufacturer: Chicony Electronics Co.,Ltd.
[ 2.599288] usb 2-1.2: SerialNumber: 0x0001
[ 2.678459] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.678490] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.680231] ata1.00: ATA-9: HGST HTS541010A9E680, JA0OA7G0, max UDMA/133
[ 2.680237] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 2.682055] ata1.00: configured for UDMA/133
[ 2.682496] scsi 0:0:0:0: Direct-Access ATA HGST HTS541010A9 A7G0 PQ: 0 ANSI: 5
[ 2.683033] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.683166] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 2.683170] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.683225] ata2.00: ATAPI: hp DVDRW GUD1N, MD00, max UDMA/133
[ 2.683245] sd 0:0:0:0: [sda] Write Protect is off
[ 2.683250] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.683326] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.684582] ata2.00: configured for UDMA/133
[ 2.689205] scsi 1:0:0:0: CD-ROM hp DVDRW GUD1N MD00 PQ: 0 ANSI: 5
[ 2.759832] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.759839] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.764273] sda: sda1 sda2 sda3
[ 2.765562] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.774958] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.775165] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.959387] psmouse serio1: synaptics: queried max coordinates: x [..5656], y [..4712]
[ 2.989833] psmouse serio1: synaptics: queried min coordinates: x [1326..], y [1200..]
[ 2.989848] psmouse serio1: synaptics: Your touchpad (PNP: SYN3202 PNP0f13) says it can support a different bus. If i2c-hid and hid-rmi are not used, you might want to try setting psmouse.synaptics_intertouch to 1 and report this to linux-input@vger.kernel.org.
[ 3.051872] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x12e800/0x0, board id: 2997, fw id: 1665536
[ 3.089851] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 3.662717] fbcon: Taking over console
[ 3.662905] Console: switching to colour frame buffer device 200x56
[ 3.771969] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 5.992254] systemd[1]: Inserted module 'autofs4'
[ 6.269350] systemd[1]: systemd 245.4-4ubuntu3 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[ 6.286673] systemd[1]: Detected architecture x86-64.
[ 6.320920] systemd[1]: Set hostname to <mag-PC-HP>.
[ 8.393868] systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
[ 9.133304] systemd[1]: Created slice system-modprobe.slice.
[ 9.133994] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 9.134621] systemd[1]: Created slice User and Session Slice.
[ 9.134780] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 9.135295] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 9.135421] systemd[1]: Reached target User and Group Name Lookups.
[ 9.135468] systemd[1]: Reached target Remote File Systems.
[ 9.135500] systemd[1]: Reached target Slices.
[ 9.152439] systemd[1]: Listening on Syslog Socket.
[ 9.152774] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 9.152924] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 9.153380] systemd[1]: Listening on Journal Audit Socket.
[ 9.153611] systemd[1]: Listening on Journal Socket (/dev/log).
[ 9.153888] systemd[1]: Listening on Journal Socket.
[ 9.154162] systemd[1]: Listening on udev Control Socket.
[ 9.154382] systemd[1]: Listening on udev Kernel Socket.
[ 9.156983] systemd[1]: Mounting Huge Pages File System...
[ 9.159573] systemd[1]: Mounting POSIX Message Queue File System...
[ 9.162497] systemd[1]: Mounting Kernel Debug File System...
[ 9.165239] systemd[1]: Mounting Kernel Trace File System...
[ 9.168991] systemd[1]: Starting Journal Service...
[ 9.187080] systemd[1]: Starting Set the console keyboard layout...
[ 9.190181] systemd[1]: Starting Create list of static device nodes for the current kernel...
[ 9.192834] systemd[1]: Starting Load Kernel Module drm...
[ 9.222913] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 9.223019] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 9.227313] systemd[1]: Starting Load Kernel Modules...
[ 9.229884] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 9.233028] systemd[1]: Starting udev Coldplug all Devices...
[ 9.235706] systemd[1]: Starting Uncomplicated firewall...
[ 9.240310] systemd[1]: Mounted Huge Pages File System.
[ 9.240619] systemd[1]: Mounted POSIX Message Queue File System.
[ 9.240873] systemd[1]: Mounted Kernel Debug File System.
[ 9.241118] systemd[1]: Mounted Kernel Trace File System.
[ 9.270599] systemd[1]: Finished Create list of static device nodes for the current kernel.
[ 9.337492] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[ 9.341501] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 9.649714] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 9.649860] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 9.652188] systemd[1]: Starting Load/Save Random Seed...
[ 9.654577] systemd[1]: Starting Create System Users...
[ 9.655528] systemd[1]: modprobe@drm.service: Succeeded.
[ 9.656484] systemd[1]: Finished Load Kernel Module drm.
[ 9.659763] systemd[1]: Finished Uncomplicated firewall.
[ 9.660728] lp: driver loaded but no devices found
[ 9.671973] ppdev: user-space parallel port driver
[ 9.759790] systemd[1]: Finished Load Kernel Modules.
[ 9.762811] systemd[1]: Mounting FUSE Control File System...
[ 9.766146] systemd[1]: Mounting Kernel Configuration File System...
[ 9.774111] systemd[1]: Starting Apply Kernel Variables...
[ 9.780330] systemd[1]: Mounted FUSE Control File System.
[ 9.780656] systemd[1]: Mounted Kernel Configuration File System.
[ 9.880454] systemd[1]: Started Journal Service.
[ 9.985489] systemd-journald[271]: Received client request to flush runtime journal.
[ 14.182630] input: HP Wireless hotkeys as /devices/virtual/input/input8
[ 14.726015] ccp 0000:00:08.0: 4 command queues available
[ 14.726611] ccp 0000:00:08.0: ccp enabled
[ 15.368060] input: HP WMI hotkeys as /devices/virtual/input/input9
[ 16.036503] cryptd: max_cpu_qlen set to 1000
[ 16.195944] [drm] radeon kernel modesetting enabled.
[ 16.196051] radeon 0000:00:01.0: remove_conflicting_pci_framebuffers: bar 0: 0xc0000000 -> 0xcfffffff
[ 16.196055] radeon 0000:00:01.0: remove_conflicting_pci_framebuffers: bar 2: 0xd0000000 -> 0xd07fffff
[ 16.196059] radeon 0000:00:01.0: remove_conflicting_pci_framebuffers: bar 5: 0xfeb00000 -> 0xfeb3ffff
[ 16.196063] checking generic (c0000000 57f000) vs hw (c0000000 10000000)
[ 16.196065] fb0: switching to radeondrmfb from EFI VGA
[ 16.196341] Console: switching to colour dummy device 80x25
[ 16.196439] radeon 0000:00:01.0: vgaarb: deactivate vga console
[ 16.197037] [drm] initializing kernel modesetting (MULLINS 0x1002:0x9852 0x103C:0x8130 0x00).
[ 16.197076] [drm] doorbell mmio base: 0xD0000000
[ 16.197077] [drm] doorbell mmio size: 8388608
[ 16.197125] ATOM BIOS: AMD
[ 16.197239] radeon 0000:00:01.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 16.197243] radeon 0000:00:01.0: GTT: 2048M 0x0000000040000000 - 0x00000000BFFFFFFF
[ 16.197250] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 16.197251] [drm] RAM width 128bits DDR
[ 16.197406] [TTM] Zone kernel: Available graphics memory: 2495016 KiB
[ 16.197408] [TTM] Zone dma32: Available graphics memory: 2097152 KiB
[ 16.197410] [TTM] Initializing pool allocator
[ 16.197419] [TTM] Initializing DMA pool allocator
[ 16.197469] [drm] radeon: 1024M of VRAM memory ready
[ 16.197471] [drm] radeon: 2048M of GTT memory ready.
[ 16.197490] [drm] Loading mullins Microcode
[ 16.297372] AVX version of gcm_enc/dec engaged.
[ 16.297376] AES CTR mode by8 optimization enabled
[ 16.611176] mc: Linux media interface: v0.10
[ 16.704347] videodev: Linux video capture interface: v2.00
[ 17.878852] kvm: disabled by bios
[ 17.916031] kvm: disabled by bios
[ 17.922519] [drm] Internal thermal controller without fan control
[ 17.924093] [drm] radeon: dpm initialized
[ 17.945771] [drm] Found UVD firmware Version: 1.64 Family ID: 9
[ 17.956343] kvm: disabled by bios
[ 17.985002] [drm] Found VCE firmware/feedback version 40.2.2 / 15!
[ 17.985042] [drm] GART: num cpu pages 524288, num gpu pages 524288
[ 18.012111] kvm: disabled by bios
[ 18.026635] [drm] PCIE GART of 2048M enabled (table at 0x000000000030E000).
[ 18.026857] radeon 0000:00:01.0: WB enabled
[ 18.026887] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0x000000008543e7dd
[ 18.026892] radeon 0000:00:01.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0x00000000546706d5
[ 18.026896] radeon 0000:00:01.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0x000000007451868e
[ 18.026899] radeon 0000:00:01.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0x000000004662f2a7
[ 18.026903] radeon 0000:00:01.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0x0000000005cd2c71
[ 18.027784] radeon 0000:00:01.0: fence driver on ring 5 use gpu addr 0x0000000000078d30 and cpu addr 0x000000007a7c0717
[ 18.028025] radeon 0000:00:01.0: fence driver on ring 6 use gpu addr 0x0000000040000c18 and cpu addr 0x00000000f9439f8a
[ 18.028028] radeon 0000:00:01.0: fence driver on ring 7 use gpu addr 0x0000000040000c1c and cpu addr 0x000000008b8c30e4
[ 18.028033] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 18.028034] [drm] Driver supports precise vblank timestamp query.
[ 18.028120] radeon 0000:00:01.0: radeon: using MSI.
[ 18.028161] [drm] radeon: irq initialized.
[ 18.032907] [drm] ring test on 0 succeeded in 2 usecs
[ 18.033012] [drm] ring test on 1 succeeded in 2 usecs
[ 18.033035] [drm] ring test on 2 succeeded in 2 usecs
[ 18.033266] [drm] ring test on 3 succeeded in 4 usecs
[ 18.033275] [drm] ring test on 4 succeeded in 4 usecs
[ 18.059146] [drm] ring test on 5 succeeded in 2 usecs
[ 18.059176] [drm] UVD initialized successfully.
[ 18.168441] [drm] ring test on 6 succeeded in 12 usecs
[ 18.168453] [drm] ring test on 7 succeeded in 2 usecs
[ 18.168454] [drm] VCE initialized successfully.
[ 18.170190] [drm] ib test on ring 0 succeeded in 0 usecs
[ 18.170384] [drm] ib test on ring 1 succeeded in 0 usecs
[ 18.170543] [drm] ib test on ring 2 succeeded in 0 usecs
[ 18.170706] [drm] ib test on ring 3 succeeded in 0 usecs
[ 18.170864] [drm] ib test on ring 4 succeeded in 0 usecs
[ 18.186961] MCE: In-kernel MCE decoding enabled.
[ 18.198217] uvcvideo: Found UVC 1.00 device HP Webcam (04f2:b52d)
[ 18.199069] uvcvideo: Failed to query (GET_INFO) UVC control 8 on unit 1: -32 (exp. 1).
[ 18.208847] input: HP Webcam: HP Webcam as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input10
[ 18.209044] usbcore: registered new interface driver uvcvideo
[ 18.209046] USB Video Class driver (1.1.1)
[ 18.248554] EDAC amd64: Node 0: DRAM ECC disabled.
[ 18.248560] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 18.287132] EDAC amd64: Node 0: DRAM ECC disabled.
[ 18.287138] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 18.293694] snd_hda_intel 0000:00:01.1: enabling device (0000 -> 0002)
[ 18.293955] snd_hda_intel 0000:00:01.1: Force to non-snoop mode
[ 18.339663] EDAC amd64: Node 0: DRAM ECC disabled.
[ 18.339669] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 18.343009] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input11
[ 18.399195] EDAC amd64: Node 0: DRAM ECC disabled.
[ 18.399201] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 18.669316] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC3227: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[ 18.669323] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 18.669327] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 18.669329] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 18.669332] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 18.669335] snd_hda_codec_realtek hdaudioC1D0: Mic=0x19
[ 18.669338] snd_hda_codec_realtek hdaudioC1D0: Internal Mic=0x12
[ 18.678421] [drm] ib test on ring 5 succeeded
[ 18.679076] [drm] ib test on ring 6 succeeded
[ 18.679593] [drm] ib test on ring 7 succeeded
[ 18.682303] [drm] radeon atom DIG backlight initialized
[ 18.682308] [drm] Radeon Display Connectors
[ 18.682310] [drm] Connector 0:
[ 18.682311] [drm] eDP-1
[ 18.682312] [drm] HPD1
[ 18.682315] [drm] DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[ 18.682316] [drm] Encoders:
[ 18.682318] [drm] LCD1: INTERNAL_UNIPHY
[ 18.682319] [drm] Connector 1:
[ 18.682320] [drm] HDMI-A-1
[ 18.682321] [drm] HPD2
[ 18.682324] [drm] DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[ 18.682325] [drm] Encoders:
[ 18.682326] [drm] DFP1: INTERNAL_UNIPHY
[ 18.687984] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input12
[ 18.688144] input: HD-Audio Generic Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input13
[ 19.570085] [drm] fb mappable at 0xC0731000
[ 19.570089] [drm] vram apper at 0xC0000000
[ 19.570091] [drm] size 5787648
[ 19.570092] [drm] fb depth is 24
[ 19.570093] [drm] pitch is 6400
[ 19.570398] fbcon: radeondrmfb (fb0) is primary device
[ 19.570674] Console: switching to colour frame buffer device 200x56
[ 19.570745] radeon 0000:00:01.0: fb0: radeondrmfb frame buffer device
[ 19.660316] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:01.0 on minor 0
[ 19.869924] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
[ 19.869928] AMD-Vi: AMD IOMMUv2 functionality not available on this system
[ 20.343316] [drm] amdgpu kernel modesetting enabled.
[ 20.343615] CRAT table not found
[ 20.343625] Virtual CRAT table created for CPU
[ 20.343627] Parsing CRAT table with 1 nodes
[ 20.343631] Creating topology SYSFS entries
[ 20.343662] Topology: Add CPU node
[ 20.343663] Finished initializing topology
[ 25.266411] Adding 15625212k swap on /dev/sda2. Priority:-2 extents:1 across:15625212k FS
[ 26.451786] audit: type=1400 audit(1609593309.193:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=640 comm="apparmor_parser"
[ 26.451798] audit: type=1400 audit(1609593309.193:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=641 comm="apparmor_parser"
[ 26.475986] audit: type=1400 audit(1609593309.217:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ippusbxd" pid=639 comm="apparmor_parser"
[ 26.706614] audit: type=1400 audit(1609593309.449:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=643 comm="apparmor_parser"
[ 26.706625] audit: type=1400 audit(1609593309.449:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=643 comm="apparmor_parser"
[ 26.796758] audit: type=1400 audit(1609593309.537:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/tcpdump" pid=646 comm="apparmor_parser"
[ 26.798774] audit: type=1400 audit(1609593309.541:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=644 comm="apparmor_parser"
[ 26.798784] audit: type=1400 audit(1609593309.541:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=644 comm="apparmor_parser"
[ 26.798790] audit: type=1400 audit(1609593309.541:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=644 comm="apparmor_parser"
[ 26.798796] audit: type=1400 audit(1609593309.541:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=644 comm="apparmor_parser"
[ 38.246527] kauditd_printk_skb: 27 callbacks suppressed
[ 38.246531] audit: type=1400 audit(1609593320.989:39): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=783 comm="cups-browsed" capability=23 capname="sys_nice"
[ 109.152625] rfkill: input handler disabled
[ 110.947246] audit: type=1400 audit(1609593393.689:40): apparmor="DENIED" operation="capable" profile="/snap/snapd/10492/usr/lib/snapd/snap-confine" pid=1591 comm="snap-confine" capability=4 capname="fsetid"
[ 122.376539] audit: type=1326 audit(1609593405.117:41): auid=1000 uid=1000 gid=1000 ses=2 pid=1591 comm="snap-store" exe="/snap/snap-store/518/usr/bin/snap-store" sig=0 arch=c000003e syscall=314 compat=0 ip=0x7f338382f639 code=0x50000
[ 123.946699] audit: type=1107 audit(1609593406.689:42): pid=681 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/NetworkManager" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.12" pid=1591 label="snap.snap-store.ubuntu-software" peer_pid=682 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[ 129.675063] audit: type=1107 audit(1609593412.417:43): pid=681 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.7" pid=1591 label="snap.snap-store.ubuntu-software" peer_pid=713 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[ 129.676249] audit: type=1107 audit(1609593412.417:44): pid=681 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.PolicyKit1.Authority" member="CheckAuthorization" mask="send" name=":1.7" pid=1591 label="snap.snap-store.ubuntu-software" peer_pid=713 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[ 130.126390] audit: type=1107 audit(1609593412.865:45): pid=681 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.DBus.Properties" member="GetAll" mask="send" name=":1.7" pid=1591 label="snap.snap-store.ubuntu-software" peer_pid=713 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[ 130.127829] audit: type=1107 audit(1609593412.869:46): pid=681 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call" bus="system" path="/org/freedesktop/PolicyKit1/Authority" interface="org.freedesktop.PolicyKit1.Authority" member="CheckAuthorization" mask="send" name=":1.7" pid=1591 label="snap.snap-store.ubuntu-software" peer_pid=713 peer_label="unconfined"
exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[ 132.613720] audit: type=1400 audit(1609593415.353:47): apparmor="DENIED" operation="open" profile="snap.snap-store.ubuntu-software" name="/etc/PackageKit/Vendor.conf" pid=1591 comm="snap-store" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
mag@mag-PC-HP:~$ Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#35 Le 02/01/2021, à 16:20
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Alors je m'attendais pas à ça!
La carte a vraiment disparu.
Quelques infos retirées de dmesg:
BIOS may not properly restore RDRAND after suspend, hiding RDRAND via CPUID. Use rdrand=force to reenable.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.016773] acpi PNP0A03:00: _OSC: platform does not support [PME LTR]
[ 1.020604] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
pci 0000:00:12.0: PME# does not work under D3, disabling it
[ 1.644299] tpm_crb MSFT0101:00: [Firmware Bug]: ACPI region does not cover the entire command/response buffer. [mem 0x7d004000-0x7d004fff flags 0x200] vs 7d004000 4000
[ 1.644309] tpm_crb MSFT0101:00: can't request region for resource [mem 0x7d004000-0x7d004fff]
[ 1.644321] tpm_crb: probe of MSFT0101:00 failed with error -16
[ 14.182630] input: HP Wireless hotkeys as /devices/virtual/input/input8
[ 18.248560] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)Je vais faire quelques recherches
Peux tu indiquer le modèle exact de pc? J'aimerais faire des recherches sur son bios.
Pourrais tu essayer de passer le paramètre noyau pci=nocrs et de tester le wifi? Tu peux suivre https://doc.ubuntu-fr.org/kernel#modifi … temporaire pour cela
Dernière modification par Nuliel (Le 02/01/2021, à 16:29)
Hors ligne
#36 Le 02/01/2021, à 16:41
- xubu1957
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Bonjour,
@Nuliel
Pour info, un pilote de substitution (rtl8818ce) était proposé au commentaire #1 > Bug 1409631 - rtl8188ee, wireless connection highly unstable [NEEDINFO]
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
En ligne
#37 Le 02/01/2021, à 16:44
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Nuliel a écrit :
Alors je m'attendais pas à ça!
La carte a vraiment disparu.Peux tu indiquer le modèle exact de pc? J'aimerais faire des recherches sur son bios.
Pourrais tu essayer de passer le paramètre noyau pci=nocrs et de tester le wifi? Tu peux suivre https://doc.ubuntu-fr.org/kernel#modifi … temporaire pour cela
Alors pour le PC :
HP - 17-p136nf(Energy Star) au cas où le num de série : SN : 5CD61223JP
Je viens également de retester les paramètres de Xubu1957 ... (avec la fonction echo ....) et rien à faire, il ne trouve pas mon réseau wifi ni mes voisins, par contre la Carte Wifi est bien allumée !!!!
J'essaie de remettre en fonction la wifi et j'essaie ton option
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#38 Le 02/01/2021, à 17:53
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
pas bien compris l'essai de cette option pci=nocrs
même avec l'exemple de Malbo .... c'est après le quiet splash mais on met quoi entre ? désolé jamais fait cette manip. Et c'est bien temporaire, c'est ça ? juste pour un essai ? si ça marche pas et que je redémarre, l'option disparaît de grub ?
Merci d'avance
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#39 Le 02/01/2021, à 19:00
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Pour ajouter cette option temporairement, tu démarres et tu appuies sur Maj assez tôt dans le démarrage du pc pour faire apparaître le menu grub (sauf s'il apparaît par défaut), puis tu fais e sur la première entrée pour éditer le démarrage, et tu ajoutes l'option pci=nocrs entre quiet et splash, ce qui donnera:
quiet pci=nocrs splashpuis tu fais F10 pour démarrer et tu testes le wifi
PS: le clavier est en QWERTY, faudra chercher un peu pour entrer pci=nocrs (certes moins que pour des paramètres à rallonge comme modprobe.blacklist=nouveau)
Dernière modification par Nuliel (Le 02/01/2021, à 19:02)
Hors ligne
#40 Le 02/01/2021, à 21:29
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Nuliel a écrit :
Pour ajouter cette option temporairement, tu démarres et tu appuies sur Maj assez tôt dans le démarrage du pc pour faire apparaître le menu grub (sauf s'il apparaît par défaut), puis tu fais e sur la première entrée pour éditer le démarrage, et tu ajoutes l'option pci=nocrs entre quiet et splash, ce qui donnera:
quiet pci=nocrs splashpuis tu fais F10 pour démarrer et tu testes le wifi
PS: le clavier est en QWERTY, faudra chercher un peu pour entrer pci=nocrs (certes moins que pour des paramètres à rallonge comme modprobe.blacklist=nouveau)
Ok je comprends mieux.
Par contre je n'arrive pas à obtenir Grub au démarrage.
MAJ ne donne rien et ESC lance un programme lié au PC HP. Un raccourci simplifié pour le bios, par exemple je peux choisir l'option du périphérique de démarrage.
Dès que j'ai trouvé comment faire je te dis, ou si quelqu'un a la combine ici ...
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#41 Le 02/01/2021, à 21:43
- moko138
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
ce qui donnera:
quiet pci=nocrs splashpuis tu fais F10 pour démarrer et tu testes le wifi
PS: le clavier est en QWERTY,
claviers_qwerty_azerty_equivalence.png :
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#42 Le 02/01/2021, à 22:08
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
shyalan a écrit :
Par contre je n'arrive pas à obtenir Grub au démarrage.
MAJ ne donne rien et ESC lance un programme lié au PC HP. Un raccourci simplifié pour le bios, par exemple je peux choisir l'option du périphérique de démarrage.
Dès que j'ai trouvé comment faire je te dis, ou si quelqu'un a la combine ici ...
Bon là je ne vois pas ...
Je presse ESC ... puis F9 et là j'ai accès à quoi lancer au démarrage.
1)EFI Ubuntu
2) EFI windows (alors que je l'ai viré ! ???)
3) autres fichiers ( .... grubx64 un truc comme ça mais cela ne me mets pas non plus Grub )
Je sais pas quoi faire pour le moment ...
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#43 Le 02/01/2021, à 22:13
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
@shyalan: essaie d'allumer, attendre un peu et ensuite appuyer sur Esc. Si vraiment tu n'y arrives pas on fera une modif pour le faire apparaître à chaque démarrage.
@moko138: Je garde ton image sous le coude, c'est bien pratique!
Edit: appuie sur Esc après avoir choisi de démarrer ubuntu efi
Le fichier efi de windows est resté, mais il ne chargera rien.
Dernière modification par Nuliel (Le 02/01/2021, à 22:14)
Hors ligne
#44 Le 03/01/2021, à 00:57
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Nuliel a écrit :
Edit: appuie sur Esc après avoir choisi de démarrer ubuntu efi
Oui c'est pertinent ta remarque ! Donc je tombe bien sur Grub après avoir choisi EFI ubuntu et avoir de nouveau appuyé sur ESC mais il n'y a aucun choix ! La version en haut de grub et puis
grub>C'est tout ...
Désolé 
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#45 Le 03/01/2021, à 11:49
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Une fois dans le menu grub, tu as bien appuyé sur E? Tu devrais avoir un texte assez long, dans le bas tu devrais trouver quiet splash
Hors ligne
#46 Le 03/01/2021, à 21:44
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Moi j'ai ça , peut importe le fichier UEFI que j'utilise
Et avec ça je peux rien faire apparemment, enfin moi je sais pas faire en tout cas.
Appuyer sur E ne donne rien. command invalid
Dernière modification par shyalan (Le 03/01/2021, à 21:47)
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#47 Le 03/01/2021, à 22:58
- Nuliel
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Techniquement si on peut faire des choses avec, mais bon, c'est pas simple.
On va prendre la méthode alternative: tu peux donner
cat /etc/default/grubafin que je t'indique les modifs à faire pour afficher à chaque démarrage le menu grub
Hors ligne
#48 Le 04/01/2021, à 01:36
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Nuliel a écrit :
Techniquement si on peut faire des choses avec, mais bon, c'est pas simple.
On va prendre la méthode alternative: tu peux donner
cat /etc/default/grubafin que je t'indique les modifs à faire pour afficher à chaque démarrage le menu grub
Voilà Nuliel,
Désolé pour le contre temps avec ce problème avec Grub et les PC HP
voici le retour :
mag@mag-PC-HP:~$ cat /etc/default/grub
# If you change this file, run 'update-grub' afterwards to update
# /boot/grub/grub.cfg.
# For full documentation of the options in this file, see:
# info -f grub -n 'Simple configuration'
GRUB_DEFAULT=0
GRUB_TIMEOUT_STYLE=hidden
GRUB_TIMEOUT=0
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX=""
# Uncomment to enable BadRAM filtering, modify to suit your needs
# This works with Linux (no patch required) and with any kernel that obtains
# the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...)
#GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef"
# Uncomment to disable graphical terminal (grub-pc only)
#GRUB_TERMINAL=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
#GRUB_GFXMODE=640x480
# Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
#GRUB_DISABLE_RECOVERY="true"
# Uncomment to get a beep at grub start
#GRUB_INIT_TUNE="480 440 1"
mag@mag-PC-HP:~$ Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne
#49 Le 04/01/2021, à 08:15
- NicoApi73
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
Bonjour,
Commence par sauvegarder ton fichier de config :
sudo cp /etc/default/grub /etc/default/grub.bakEnsuite, tu édites ce fichier avec la commande suivante :
sudo nano /etc/default/grubTu te déplaces avec les touches clavier pour aller à la ligne :
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"et tu ajoutes pci=nocrs avant on après splash, pour obtenir :
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash pci=nocrs"Tu tapes les touches suivantes pour sauvegarder et sortir :
CTRL + o (le lettre o)
Entrée
CTRL + x (la lettre x)
Tu mets à jour grub :
sudo update-grubEt tu rebootes :
rebootHors ligne
#50 Le 04/01/2021, à 19:37
- shyalan
Re : WIFI RTL8188EE ne fonctionne qu'après un redémarrage
NicoApi73 a écrit :
Bonjour,
Commence par sauvegarder ton fichier de config :
sudo cp /etc/default/grub /etc/default/grub.bakEnsuite, tu édites ce fichier avec la commande suivante :
sudo nano /etc/default/grubTu te déplaces avec les touches clavier pour aller à la ligne :
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"et tu ajoutes pci=nocrs avant on après splash, pour obtenir :
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash pci=nocrs"Tu tapes les touches suivantes pour sauvegarder et sortir :
CTRL + o (le lettre o)
Entrée
CTRL + x (la lettre x)Tu mets à jour grub :
sudo update-grubEt tu rebootes :
reboot
Ok mais par contre cette manip est definitive contrairement à celle de Nuliel et cela ne replace pas grub au démarrage ? Si ?
Asus Gamer G55VW - i7 - 16 Go Ram - Nvidia GTX 660M (2Go dédié) - Ubuntu 20.04 (j'ai viré windows !!! enfin !)
Hors ligne